6509 upgrade sup 720 to 2t - wism1 not working

Hi,
after upgrading to 2t supervisor our wism controller is not working properly.
I can connect to it via service ip address but via management I can't.
status is ok, on line diagnostic is ok... but all AP are not working.
on 6509 we are runing
bootdisk:s2t54-adventerprisek9-mz.SPA.151-2.SY.bin
on wism:
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.240.0
RTOS Version..................................... 7.0.240.0
Bootloader Version............................... 7.0.240.0
Emergency Image Version.......................... 7.0.240.0
Build Type....................................... DATA + WPS
Mod Ports Card Type                              Model              Serial No.
1   16 CEF720 16 port 10GE                    WS-X6716-10GE
2    6 Firewall Module                        WS-SVC-FWM-1
3   10 WiSM WLAN Service Module               WS-SVC-WISM-1-K9
5    5 Supervisor Engine 2T 10GE w/ CTS (Acti VS-SUP2T-10G
Mod MAC addresses                       Hw    Fw           Sw           Status
1 f866.f220.08 to f86.f220.07   1.0   12.2(18r)S1 15.1(2)SY    Ok
2 0023.3d.e174 to 00.334d.e17b   4.5   7.2(1)       4.1(9)       Ok
3 0025.87.d73a to 025.84.d749   2.3   12.2(14r)S5 15.1(2)SY    Ok
5 5057.a8.1d to 505a8.1d18   1.5   12.2(50r)SYS 15.1(2)SY    Ok
Mod Sub-Module                  Model              Serial       Hw     Status
1 Distributed Forwarding Card WS-F6K-DFC4-E        1.2    Ok
3 Centralized Forwarding Card WS-SVC-WISM-1-K9-D   2.1    Ok
5 Policy Feature Card 4       VS-F6K-PFC4          2.1    Ok
5 CPU Daughterboard           VS-F6K-MSFC5         2.1    Ok
Mod Online Diag Status
1 Pass
2 Pass
3 Pass
5 Pass
is there problem with ios incapability or am I doing something wrong.
regards,
Ivan

Ok i think the problem is in:
Port-channel1          unassigned      YES unset down                  down
Port-channel2          unassigned      YES unset down                  down
WiSM Controller 2 in Slot 3 not configured
Operational Status of the Controller : Oper-Up
Service VLAN                         : 702
Service Port                         : 10
Service Port Mac Address             : 0023.eb01.c322
Service IP Address                   : 10.7.2.12
Management IP Address                : 10.7.3.20
Software Version                     : 7.0.240.0
Port Channel Number                  : 0
WCP Keep Alive Missed                : 0
i just need to figure this out :-))
Thx.

Similar Messages

After upgrading to Lion internal mic does not work with Facetime

After upgrading to Lion internal mic does not work with Facetime. The mic is picking up sound as noted in System Prefs. This was working just fine before the updgrade. Facetime works OK on my iPod.

you have in french a tutorial to recreate your partition here
Rebuild partition with Recovery HD lion after upgrade to 10.7.2
i tested, it's work !
For your wifi problem:
Try to change your setup of wifi, look this table given by apple:
I changed my wifi setup wep to wpa and it's work !

After upgrading to Lion Image Capture does not work, even though it is intel software. Gives error 9931. What gives?

After upgrading to Lion, Image Capture does not work, even though it is intel software. Gives error 9931. What gives?

Ouch, if it is indeed damaged, then sadly you need to restore the whole danged huge OS!
Didn't used to be this way before Lion/10.7.
Bootup holding CMD+r, or the Option/alt key to boot from the Restore partition & use Disk Utility from there to Repair the Disk, then Repair Permissions.
If that doesn't help Reinstall the OS.

IPAD Mini Locked after iOS upgrade, tried reset on iPAD did not work, plugged in and device not appearing in iTUNEs for reset/restore

PAD Mini Locked after iOS upgrade, tried reset on iPAD did not work, plugged in and device not appearing in iTUNEs for reset/restore. Just get an Apple Logo then a flashing blue screen as if it is caught booting up. This has happened twice before and iTunes restore fixed it. But this time device not appearing in iTunes.
Running iTunes for PC. But as stated restore has worked before! Any help greatly appreciated!!

Place the device in DFU mode and let iTunes restore the device to factory condition.

I updated software upgrade from itunes. now phone will not work at all. only have picture of apple icon and usb on screen

i downloaded an upgrade from itunes last night to os5.1 i think. it said there was a problem with the download. now my phone will not work at all. it just has a picture of the itunes logo ans a picture of a usb cable on it. my computer will not recognise phone either

http://support.apple.com/kb/TS1538
Try rebooting it and connect. Make sure you're connected directly to a USB port using the Apple USB cable.

ISE upgrade 1.2: Self-provisioning portal not working

Hi all,
I need help with Self-Provisioning portal flow not showing the agent installation page after upgrade from 1.1.1 to 1.2 on a couple of 3315. I've configured all the pieces as instructed by BYOD SBA guide at http://www.cisco.com/en/US/docs/solutions/SBA/February2013/Cisco_SBA_SLN_BYOD_InternalCorporateAccessDeploymentGuide-Feb2013.pdf
Screenshot of page is attached:
I've checked ise-console.log application log file and found two errors correponding to the first page:
[portal-http-84431][] SystemConsole -::c0a8a82a000000d7523c70f9::guest:- com.cisco.cpm.provisioning.exception.ProvisioningException: java.security.cert.CertificateException: Unable to initialize, java.io.IOException: DerInputStream.getLength(): lengthTag=127, too big.
[portal-http-84431][] SystemConsole -::c0a8a82a000000d7523c70f9::guest:- at com.cisco.cpm.provisioning.cert.CertProvisioningFactory.initialize(CertProvisioningFactory.java:333)
and the second (not working) one:
[portal-http-84431][] SystemConsole -:xxxxx@xxxxxxx:c0a8a82a000000d7523c70f9::guest:- java.lang.NullPointerException
[portal-http-84431][] SystemConsole -:xxxxx@xxxxxxx:c0a8a82a000000d7523c70f9::guest:- at com.cisco.cpm.provisioning.cache.FlowStateCacheManager.getFlowStateCache(FlowStateCacheManager.java:202)
Looks like something is wrong with a certification file, but I cannot find what is. I've exported and re-installed current server certificates (as instructed by upgrade guide for 1.2) and nothing changed.
Can somebody please help?
Thanks,
L

Errors When Adding Devices to My Devices Portal
Employees cannot add a device that is already added if another employee has previously added the device so that it already exists in the Cisco ISE endpoints database.
If employees are attempting to add a device that supports a native supplicant, recommend that they use that instead. That registration process will overwrite the original registration and switch ownership to the new user.
If the device is a MAC Authentication Bypass (MAB) device, such as a printer, then you must resolve ownership of the device, and if appropriate, remove the device from the endpoints database so that the new owner can successfully add the device.
For more information on self-provisioning.
http://www.cisco.com/en/US/docs/security/ise/1.2/user_guide/ise_mydevices.html Errors When Adding Devices to My Devices Portal
Employees cannot add a device that is already added if another employee has previously added the device so that it already exists in the Cisco ISE endpoints database.
If employees are attempting to add a device that supports a native supplicant, recommend that they use that instead. That registration process will overwrite the original registration and switch ownership to the new user.
If the device is a MAC Authentication Bypass (MAB) device, such as a printer, then you must resolve ownership of the device, and if appropriate, remove the device from the endpoints database so that the new owner can successfully add the device.
For more information on self-provisioning.
http://www.cisco.com/en/US/docs/security/ise/1.2/user_guide/ise_mydevices.html

Upgraded to ios 6 Apple Tv not working! How do I Fix this?

The apple tv is connected to a Sony Bravia using a HDMI lead.
So the upgrading was complete (I think) and it came up with a picture of a cable and an itunes store icon.(What Does this Mean?)Now(about 4hrs later) the apple tv has a white flashing light, when I change from having the tv on to the HDMI where the apple tv is connected it showed up at first with the picture of the cable and the itunes icon but now nothing shows up. I have tried unplugging the apple tv from the power and HDMI. The Airplay (aka playing things through apple tv) feature is usually avalible automatically when a video is played our ipad, ipod and MacBook but this is not working. The apple tv doesn't show up in the itunes devices on MacBook or Ipad. It would really be appreciated if this was answered.The apple tv doesn't respond to the silver remote either.
P.S. I am not 100% sure if it is Apple TV 2 or Apple TV 3

OK so I went to the Apple Store and they said my cable was a third party cable. We tried an apple cable and it worked! So Apple changed the pin out configuration on the OS 5.1 upgrade so only Apple cables will work! So I had to shell out another $40.00 to get that cable!

Lumia 720 volume down button not working

Hey buddies, I'm using lumia 720 and often i get this volume down button not working.
I changed the button by giving it in nokia care for 3times and still im facing the same problem.
And also noticed that this is happening to most of the lumia 720's.
so kindly look into it and rectify the problem as soon as possible.
If there is any solution for this, kindly reply me.
Thanks in advance...!

Your only solution would be to return the unit back to nokia care for inspection,if there is a recurring issue with this im sure nokia would be aware of it now,and it could be a slight manufacturing defect which again would be looked into.
If i have helped at all a click on the white star below would be nice thanks.
Now using the Lumia 1520

Nokia Lumia 720 down volume button not working aft...

Hi just got my Lumia 720 25 days back and now i'm having this issue going on started from today after I wake up my phone the down volume button does not work for a while. What i noticed is until i press the Up volume button the down volume button does not respond anuthing. Is that a software problem ? Because i feel like if i press it little harder than usual it start working fine.
Not sure what to do ? Like it will get resolved with an upcoming update or an hardware issue ? Should I need to check with the Nokia Care.
I already tried to do a soft reset thrice but it still the same. Someone please help !
Thanks in advance.

Even I have the same issue with my Newly purchased nokia lumia 720... Sometime the volume down buttons works perfectly and with time is doesn't work at all is this a software issue... i am facing this since i have downloaded an audio update.... i m tired of resetting the settings i am tired visiting service centers, as they are asking me to leave my phone for 15-20 days as the part is not available with them and my question is. if there is a hardware issue then is should stop working but in my case sometimes it works as perfect as the day i bought the device and sometimes it doesn't work at all. Will this issue be fixed with Amber update... What is the appropriate solutions for this matter please reply......

After upgrading my ipad2 my apps are not working

I have recently upgraded my IPAD 2 after a long time.. but,after upgrade apps are not working!!!

Na!!! I restored factory settings.. now not able to copy aaps from itunes to IPAD

Since mistakenly upgrading Quicktime and I Tunes will not work.

Unfortunately my amd 2700 Windows XP will not take the Service Pack 2 upgrade for whatever reason. It still functions okay, but I mistakenly upgraded my Quicktime along with I Tunes and it will not work. I later read minimum requirements on Apple's site having Service Pack 2 is required. Now I'm frustrated because I can't find an earlier version of either program to download. Unless I buy another computer I'm stuck.
amd 2700 Windows XP
amd 2700 Windows XP
amd 2700 Windows XP

First message is Windows Service Pack encountered a problem. I went to all the technical data and it is Greek to me. I can give you a couple of things, but the entire file doesn't make any sense, but then again it is a computer.
Windows: NT 5.1 (shouldn't it be XP, what do I know)
modver:5.1.2600.2180
modname: ntdll.dll
offset: 0002946
cpu vendor code: 2600 68747541 69746e65 444d4163
I tried MS for support on SP2, but only found 2 free emails if you had the product ID or it was loaded on the computer. Since I can't load it I can't email or call them. My computer was put together by a computer business so I really can't go back to them since it is not a name brand and it has been at least four years. I am still stuck on what to do. I tried to restore to before the updating of I Tunes, but MS would not let me do that.
amd 2700 Windows XP

Post RH 9 Upgrade Expand All and Collapse All not working.

After upgrading to RoboHelp 9 from 7 - the Collapse All and Expand All is not working. I am taking over after attending a RoboHelp 9 Training Class a little over a week ago, so any help would be appreciated.

Hi,
What is your output? Where are the show/hide buttons placed: In the topic or in the toolbar? You're using RoboHTML right?
Did you use any kind of twisties in your RoboHelp 7 project? The show all hide all buttons are controlled by a custom script and I'd like to know which method you are using. (If you know which.) See also http://www.grainge.org/pages/authoring/twisty/twisty.htm
If you're not sure which method you are using, can you post the HTML of the show/hide all button/link?
Greet,
Willam

HT1338 Upgraded to Lion. IWork does not work. How do I fix this?

I increased the size of my hard drive to 1TB and upgraded from Snow Lepord to Lion. iWorks 09' (keynote, pages, numbers) and iPhoto do not work. I have used software updated and everything is current.
Is there a patch of something else I need to do to make them compatible?

Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ If you’re running Mac OS X 10.7 or later, open LaunchPad. Click Utilities, then Console in the page that opens.
Step 1
Enter the name of the crashed application or process in the Filter text field. Post the messages from the time of the last crash, if any — the text, please, not a screenshot.
Step 2
Still in the Console window, look under User Diagnostic Reports for crash reports related to the process. The report name starts with the name of the crashed process, and ends with ".crash". Select the most recent report and post the contents — again, the text, not a screenshot. For privacy’s sake, I suggest that, before posting, you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if it’s present (it may not be.) Please don’t post shutdownStall or hang logs — they're very long and not helpful.

My HP Lasrjet 1020 not work after upgrade Mavericks, My HP Lasrjet 1020 not work after upgrade Mavericks

Hi,
My HP Laserjet 1020 not working after upgrade to Mavericks.
Please provide a solution to make it work. Thanks.
Percy

Check Software Update and HP tech support for updated drivers that will work with Maverick.

Skype upgrade for Mac 10.5.8 not working

[Topic title updated by moderator to be more descriptive. Original topic title was: "Skype upgrade for Mac not working"]
Skype just left my 79 y.o. father wihtout SKYPE, he is running 10.5.8 becasuse it is good enough for him, he is used to it aafter years of using it.
You cant ask an older person to start searching forums etc.
They rely on the companies that make the products they trust.
I have helped him download and install Skype_6.3.0.604.dmg (we are 500 km away) but the program now says it is not supported.
I can tell my dad to modify the /etc/hosts file and the info.plist.
This is just ridiculous.
SKYPE: YOU SHOULD NOT GIVE THE CHANCE TO UPDATE TO A VERSION THAT IS NOT GOING TO WORK!!!!

Not to sound fraternising, but the matter of fact is that nothing has been changed in tcp/ip, that is used by Skype. What has been changed is that Microsoft now manage the code, and with that comes the Microsoft way of doing things. If this includes complete lack of version control and software management, I suggest you do not change one thing.
What you do not explain and fail to mention is that features that used to work, does not work in your new versions, and the simplest way to get it to work is to remove everything that has been changed.
What has been changed is how the tcp/ip packets are sent on the Internet. The software that MS acquired used straight forward, standard tcp/ip with non-lingering sockets, which is the ITU-T variant of tcp/ip that is also the US FCC RFC. If Microsoft wants to implement Skype on Netbios, go ahead, but do not expect others to follow, and allow the rest of the world, including those that used to run Skype on Windows, to leave and find the attempt a complete waste of time, and the software utter worthless.
It is very well defined what Skype is expected to deliver of functionality, just now, it is to perform just as good as two years ago. If you cannot acheive this by Windows used on servers on the network, that is a change that removed functionality, and did not add anything. It is simple to get it back - drop the Windows relay servers. Microsoft cannot rewrite international standards - and do not tell us to endorse any attempt of that nature. It would be nice if the world was a cube, but all your effort in telling us that it is convenient does not change facts: it will be round as a bowling ball, and tcp/ip has to be fully standard, not one that keeps open long after the connection has been taken down to allow MS to implement IPX/SPX functionality in Skype. We are not interested, and nobody is, I doubt Mr. Nadella would endorse this had he known.

6509 upgrade sup 720 to 2t - wism1 not working

Similar Messages

Maybe you are looking for