6509 with 24 10/100/100 LX connectors

i have the 6509 switch with module 24 port singlemode fiber LC connectors.
which type of patch cord should i use to connect these ports to an SC PAtch pannel
is it LC-SC ???

hi
As you have mentioned its LC-SC patch cords which is required to be used but do remember that you are going with proper single or multimode patch cords.
Since you are using LX here in your 6509 side do confirm the other end side too.
if both the sides supports single mode then you wont be having any issues in getting the connectivity thru with LC-SC single mode patch cords.
Coz some of the CWDM or other equipments may not support LX modules and you need to go for SX modules on the other side which again supports multimode patch cords.
regds

Similar Messages

  • ABZO Posting with T Type 100 By LSMW ( with Dep areas restriction)

    Hi Gurus
    I have few hundreds of Assets that are created before the Activation of New dep Areas. Now i have to updated the Acquisition costs to those 10 and 11 Dep areas only. I am able to do the update the acquisition costs to Asset master by ABZO tcode with restricted T type 100 for 10 and 11 Dep areas manually But i have to do it by LSMW process with BAPI  method,  But ended up in the following error message.
    Posting with transaction type 100 is not possible here, see long text
    Message no. AAPO177
    Diagnosis
    Transaction type 100 has a depreciation area limitation, although posting is not mandatory in all of the depreciation areas entered. However, it is not possible to select depreciation areas in the current transaction.
    Procedure
    Check the specifications for transaction type 100 or use transaction LSMW to enter the transaction.
    Please guide me the procedure to fix this issue.
    Meenakshi.N
    Edited by: Meenakshi.Nakshatrula on Jun 21, 2010 4:35 AM

    ABZO - Tcode,
    100 - Transaction type
    Assets - Non AUC assets
    Mistake is when i am recording the Session i haven't correctly determined the Depreciation areas. That lead me into error message.
    I was able to do it successfully by Batch input recording method instead of BAPI.
    Thanks
    Meenakshi.N

  • Excel 2013 (pro plus) extermely slow with sheets with more than 100 checkboxes

    I have a customer with Excel 2013 (pro plus).
    They use sheets with more than 100 checkboxes in it.
    The sheet is extremly slow to display. When a user starts scrolling down, the checkboxes appear very slowly, one by one.
    It happens with all users, on both x86 and 64bits Windows 8 PC's and Office clients (32b & 64b).
    Anyone any idea?

    Hi R.Nieraeth,
    Could you please let us know what exactly these checkbox was used for ? Any formulas depend on these checkbox? Or any VBA code in this excel file? If so, you may need to check your formulas or the VBA code.
    In addition,does this issue happen only on excel 2013? You can try to disable hardware graphics acceleration: Click
    File, and then click Options. In the Advanced group, click to select the
    Disable hardware graphics acceleration check box. Click ok.
    Also please check if the following thread is helpful:
    http://social.technet.microsoft.com/Forums/en-US/a9a257fa-ce8b-4399-860c-563022b8714f/checkbox-bug-in-excel-2010-slow-response?forum=excel

  • Reports with more than 100 columns

    I am using Apex 3.2. I am using a classic report with more than 100 columns. So to use the custom heading in the report, I exported the page,did modification in exported sql file and imported back.
    But when I am passing the parameters from a input screen for the first time either it is showing the all data avilable in the database or with only header. If I do the refresh in input screen and try it then it is working as intended. I am updating at the below loaction of the page.Let me know if I have to update anything more in the sql file.
    declare
    s varchar2(32767) := null;
    begin
    s := null;
    wwv_flow_api.create_report_columns (
    p_id=> 200100535534034253 + wwv_flow_api.g_id_offset,
    p_region_id=> 2003453533453 + wwv_flow_api.g_id_offset,
    p_flow_id=> wwv_flow.g_flow_id,
    p_query_column_id=> 157,
    p_form_element_id=> null,
    p_column_alias=> 'XYZ',
    p_column_display_sequence=> 157,
    p_column_heading=> 'XYZ 123',
    p_column_alignment=>'LEFT',
    p_disable_sort_column=>'Y',
    p_sum_column=> 'N',
    p_hidden_column=> 'N',
    p_display_as=>'WITHOUT_MODIFICATION',
    p_pk_col_source=> s,
    p_column_comment=>'');
    end;
    /

    Hi,
    Its just a general thought and I realize you know your application and user community better I do, but do you think your users are going to be very happy when they are presented with a report with more than a hundred columns? Have you considered maybe presenting the data in some sort of rolled up form from which the user can then drill down to the data they are particularly interested in. Also, I'm sure your LAN administrator would be happy not to see 100+ column by x number row reports being regularly shipped across the network.
    Also, 100+ column reports suggests tables with 100+ columns which are probably not designed in a very relationally compliant way. I find that good DB design usually results in applications that have to make less compromises, such as hacking export files in order to fool the API into making ridiculous, unsupported and unsupportable compromises.
    Just a thought..................
    Regards
    Andre

  • Is DTS supported in SQL server 2008 R2 with Compatibility level 100?

    We have a DTS package which executes one stored procedure.
    We have recently switched SQL server compatibility level from 80 to 100. 
    On Compatibility level 80 it was working fine.
    When i switched the level to 100, and executes DTS it shows successfully executed but stored procedure doenot really executed.
    When i execute stored procedure in query analyzer it executed successfully and results were as expected.
    Please let me know Is DTS supported in SQL server 2008 R2 with Compatibility level 100?

    We have just implemented DTS packages on SQL2008R2 using the Backward Compatibility Tools (serarch for SQLServer2005_BC.msi)
    You need the files:
    SQLServer2005_BC.msi or SQLServer2005_BC_x64.msi
    and SQLServer2005_DTS.msi
    After you install these, perform the following -
    1) To integrate DTS Designer with SSMS:
    Copy the files SEMSFC.DLL, SQLGUI.DLL, and SQLSVC.DLL
    from %ProgramFiles%\Microsoft SQL Server\80\Tools\Binn
    to %ProgramFiles%\Microsoft SQL Server\100\Tools\Binn\VSShell\Common7\IDE
    Copy the files SEMSFC.RLL, SQLGUI.RLL, and SQLSVC.RLL
    from %ProgramFiles%\Microsoft SQL Server\80\Tools\Binn\Resources\1033
    to %ProgramFiles%\Microsoft SQL Server\100\Tools\Binn\VSShell\Common7\IDE\Resources\1033
    2) To integrate DTS Designer with BIDS:
    Copy the files SEMSFC.DLL, SQLGUI.DLL, and SQLSVC.DLL
    from %ProgramFiles%\Microsoft SQL Server\80\Tools\Binn
    to %ProgramFiles%\Microsoft Visual Studio 9.0\Common7\IDE
    Copy the files SEMSFC.RLL, SQLGUI.RLL, and SQLSVC.RLL
    from %ProgramFiles%\Microsoft SQL Server\80\Tools\Binn\Resources\1033
    to %ProgramFiles%\Microsoft Visual Studio 9.0\Common7\IDE\Resources\1033
    T

  • HTTP send returned with status code(100,101)

    Hi Experts,
    I am facing an error in ADS at se38 --> FP_PDF_TEST_00
    Test Program: Version Information (for Analysis Only)
    SYSTEM ERROR
    ERROR CODE    :    100,101
    ERROR MESSAGE : SOAP Runtime Exception: CSoapExceptionTransport : HTTP send returned with status code
    SOAP Framework error: SOAP Runtime Exception: CSoapExceptionTransport : HTTP send returned with status code(100,101).
    Please let me know how to resolve this issue
    Thanks & Regards,
    Arun

    Hi,
    Thanks For your reply..
    I tryied but no use
    Actually Here i am tryping to do configuration between ECC6 and Bi (ABAP+JAVA) system
    Here my Bi  system no id different from ECC6 system no.
    The steps i did is
    1.created ADS HTTP RFC Connection  in ECC6 sytem
    2. System no. given as BI system no.
    3. If i give prefix:  /AdobeDocumentServices/Config?style=rpc  it is not allowing me to save  But i give /AdobeDocumentServices/Config it allows me to save
    4.And other settings i followed as document "Configuring ADS for Guided Procedures ''
    I am facing same error
    Test Program: Version Information (for Analysis Only)
    SYSTEM ERROR
    ERROR CODE    :    100,101
    ERROR MESSAGE : SOAP Runtime Exception: CSoapExceptionTransport : HTTP send returned with status code
    SOAP Framework error: SOAP Runtime Exception: CSoapExceptionTransport : HTTP send returned with status code(100,101).
    Please any body know me the solution
    Thanks & Regards,
    Arun

  • CSoap Excep Transport Http receive failed with Excp Commc_failure(100.101)

    Hi Experts;
    Am working with adobe forms. T-code SFP (Form Builder)
    I have  created a adobe form, Layout and all...
    when i Activate the Form, it's not Activating and it's showing the Status information like...
    Status Information: SOAP Framework error:SOAP Runtime Exception: CSoap Exception Transport: Http receive failed with Exception Communication_failure(100.101).
    Please Give your Suggestions !!
    Thanks
    Upender.

    Hi wd4a Adobe community
    here is another guy who has exactly the same problem trying to reproduce the example of: INTERACTIVE FORMS BY ADOBE IN WEB DYNPRO ABAP - INTRODUCTION ( http://www.sdn.sap.com/irj/scn/elearn?rid=/library/uuid/806cf26c-22e7-2c10-8ca3-a671648fd2ea ).
    Anyone out in this world who has a suggestion?
    thanks in advance ...
    Stefan

  • Do you have customer with more than 100 users ?

    Hello
    We think to place business One to a One hundred users customer.
    Do you know if it will works fine ? Do you have an existing customer with more than 100 users ?
    Thanks for answers.
    Julien

    Julien,
    The number is users is just one component in detemining if SAP B1 would work well.  If the transaction volume is low-medium then it should not be a problem.
    I have implemented a couple of 100+ user installations and they are still using B1 after 3 years.
    Minimizing the number of Alerts also helps in better system performance in case of such large installations.
    Regards
    Suda

  • I have downloaded adobe download assistant but when ever i click on sign in it says 'error communicating with adobe (error 100). please help.

    I have downloaded adobe download assistant but when ever i click on sign in it says 'error communicating with adobe (error 100). please help.

    Boskou41043636 for information on how to resolve error 100 please see Troubleshoot Adobe Download Assistant.

  • Outstanding job opportunity with a Fortune-100 national company here in South Florida.

    Outstanding job opportunity with a Fortune-100 national company here in South Florida.If you possess Strong knowledge with Hyperion Essbase; Hyperion Planning; and Hyperion Reports you are one phone call away to get hired. You will have strong finance and IT background so you could provide design expertise to consolidate the flow of information from 300+ sites into the corporate database. Endre PappSr. Technical [email protected] Staffing Solutions (S3)http://www.strategicstaff.com 954-577-5445 x18 Office954-854-3794 Mobile954-577-5453 Fax877-295-8326 x18 (Toll Free)

    "If you possess Strong knowledge with Hyperion Essbase; Hyperion Planning; and Hyperion Reports you are one phone call away to get hired."Wow.

  • Mi iphone shut off with battery at 100%

    mi iphone shut off with battery at 100%

    if you sure so your battery is down
    and you must change it

  • TS3276 cannot receive mail after i sent a large photo.   A new folder appeared called "recovered messages" with the over 100 recovered emails of the same email of the one i sent out.  i have read apple support and done everything they suggest.  Help!

    I cannot receive mail after i sent a large photo.   A new folder appeared called "recovered messages" with the over 100 recovered emails of the same email of the one i sent out.  i have read apple support and done everything they suggest.  Help!

    How large is 'large'?

  • Need the SCSI-II 100-pin connector for the PXI-6624

    Hi. I need to build a custom cable for the NI PXI-6624 and I would like to know where can I get the 100-pin connectors. Thank you.
    Daniel
    Chile

    You should be able to find the connectors here:
    Subminiature and Microminiature D Connectors .050 Series Cable Connectors (SCSI)AMP (749111-8)
    The parts are made by Tyco Electronics P/N: 749111-8
    Otis
    Training and Certification
    Product Support Engineer
    National Instruments

  • Wireless capability Compaq Presario SR1950NX with Integrated 10/100 Base-T networking interface

    Wireless capability available for 6-year old Compaq Presario SR1950NX desktop with "Integrated 10/100 Base-T networking interface" ?  How best to do this. Wireless adapter via USB 2.0 ?  Have Time Warner's modem and my Linksys N750  router in another room, and want to use wireless printer in a third room.  Router currently serves Smart TV and a Lap Top in different rooms.

    Hi:
    Yes, the easiest thing to do is to purchase an external usb wireless adapter.
    I just got this one for my desktop.
    http://www.linksys.com/en-eu/products/adapters/AE3000
    You can read some customer reviews on the adapter at the link below.
    http://www.newegg.com/Product/Product.aspx?Item=N82E16833124477
    I am very happy with mine. It connects to my Linksys E4200 router at 450 MBPS on my N only 5.0 GHz band.
    I believe that is the maximum throughput for the AE 3000 wireless adapter.
    I also like that it comes with the 3' usb extension cable and cradle to position the device for the best reception.

  • Can I replace the Inspire 5500 decoder with a DDTS-100

    Hi,
    All I want to do is replace the decoder that comes with the Inspire 5.1 Digital 5500 set with a DDTS-100, and continue to use the same speakers. Is this possible?
    The only thing I can see preventing this is that at the moment the the sub and the decoder have to be connected via a din socket (for control and power), but there is no din input on the DDTS-100. Will this be a problem?
    Thanks in advance.

    Google is a wonderful tool... Tried it's
    http://www.hardwareluxx.de/akaspar/r...s00/back_s.jpg
    Message Edited by rico01 on 08-17-2005 05:09 PM

Maybe you are looking for