6509e SUP-2T VSS and 100BASE-X SFP

Dear All,
i need to connect via 100BASE-X uplinks some access switches to 6509e VSS distribution Switches having SUP-2T.
It seems that the only module on 6509e supporting 100BASE-X SFP is WS-X6148-FE-SFP. This module is going EoS and is not supportes in VSS.
Is there any other modules that i can use?
Thanks and Regards
Giuseppe

Hi,
Here's a link that contains information about available line cards that might help you:
http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps708/product_data_sheet0900aecd801459a7.html
Regards,

Similar Messages

Qu. about Deploying MPLS on Sup-2T VSS

Hi,
We are planning to deploy a new campus network comprising of a Core (Nexus 7K), 2 client aggregation modules (Catalyst 6500 /w Sup-2T VSS) and a single Data Centre module (Nexus 7k).
MPLS is being deployed to provide segregation of services. Now in a traditional MPLS campus deployment, we would have a pair of Core switches performing the P, or LSR function, and the aggregation devices each performing the role of the PE, or LER. Load balancing would be achieved by using different RDs for each PE.
In the world of VSS however we obviously change this model, with a pair of PE switches appearing as "one" to the Core or P node. In this scenario we would just use the one RD and use a Layer-3 Port channel from the VSS node to each P node to provide the resilience.
I have read a few posts about this type of deployment and the general consensus seems to be sticking with a non VSS deployment, mainly for simplicity and the ability to have greater visibility into what is going on under the hood.
Has anyone deployed MPLS using VSS ? Does anyone have any views or recommendations as to why one would choose one particular method over the other ?
I think my personal preference will be to go non VSS, then at least we have the same configuration across all aggregation modules (Nexus / Catalyst).
Any help would be greatly appreciated.
Chris.

Hi Alessio,
The underlying design will be a traditional Access - Distribution - Core - Distribution - Access model. With a hierarchical OSPF backbone design, i.e. area 0 for Core and backbone links, with the distribution switches configured as ASBRs. We are then planning to configure an iBGP overlay on this, and then MPLS VPN using MP-BGP to provide network segregation. This is something I have done before on a Catalyst / Nexus backbone and works well, I have just never used VSS to accomplish this. So I just wanted to understand if there are any best practice recommendations for VSS which may not be in the path isolation design doc.
For example, in a traditional non VSS deployment, load balancing is typical configured by configuring different RD's across a pair of PEs with the same RT which route a common subnet. Different VPNv4 prefixes are then advertised to the Core / P nodes for the same IPv4 subnets. In a VSS deployment, this isn't possible, because obviously there is only a single control plane, so load balancing is achieved by the hash algorythm used on the Layer 3 port channels connecting the PE to the Core - are there any other considerations such as this which I need to be aware of ?
I hope this helps explain the design a little better.
Chris.

What are the differences between Easy VSS and Traditional VSS on Catalyst 4500E with Sup 8E ?

I would like to know which feature is different between Easy VSS and Traditional VSS.
I know "Easy VSS is a new way of implementing VSS by using a single command" but I cannot find more information about it.
Please help.
Thank you.
Nash

Easy VSS is a simplified and automated way of configuring VSS for first time. Once a VSS is configured then it same as traditional VSS in functionality.
There is no concept of layer 2 or layer 3 VSL link. VSL is the internal portchannel link and you cannot configure as layer 2 or layer 3 portchannel.
Following is the link of Easy VSS steps.
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/XE3-6-0E/15-22E/configuration/guide/xe-360-config/vss.html#60764

SRW2008 with a 100Base-FX SFP?

i got a 100Base-FX SFP from my localloop provider and tried to use it in a Linksys SRW2008 switch.
it seems the SFP ports are fixed to 1000Base. is there a way around this limitation?
thanks for your help.

Hi
Check software requirements and configuration requirements in the attached guide.
I think it gives you your answer (I hope )
It suggests you need 1.0.3 software and then try the following;
Manually Configuring the 100M SFP
STEP 1 On the Port Configuration page, click Detail.
STEP 2 In the Port Configuration popup window, select eth 100M in the SFP Speed field.
STEP 3 Save your changes.
STEP 4 Insert the 100M SFP module.
Hope this helps
regards Dave

100BASE-BX10 SFP

Hi All,
I have several Cisco 3560C setup at multiple stations. The Cisco 3560C are connected in a daisy chain between each other using 100BASE-BX10-D and 100BASE-BX10-U SFP. So, on the first Cisco 3560C (station 1), I have a U-type connecting to the second Cisco 3560C (station 2.). The second Cisco 3560C (station 2) will have a D-type and U-type SFP where the D-type connects to the previous station 1 on its U-type SFP. This setup repeats for station 3 onwards.
It seems that these connections between the stations, I noticed that the Cisco switch registers the link at 100Mb half-duplex and I see incrementing CRCs and collisions. I am not able to hard-code the interface to 100Mb FULL as it seems that the interface configuration does not give me the option to do a 'speed 100' or 'duplex full'.
Is this normal for these kinds of SFP?
Below are some outputs:
Cisco IOS Software, C3560C Software (C3560c405-UNIVERSALK9-M), Version 12.2(55)EX3, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 10-Aug-11 07:37 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x02100000
Switch(config)#do sh int status
Port      Name               Status       Vlan       Duplex Speed Type
Fa0/1                        notconnect   15           auto   auto 10/100BaseTX
Fa0/2                        notconnect   15           auto   auto 10/100BaseTX
Fa0/3                        notconnect   15           auto   auto 10/100BaseTX
Fa0/4                        notconnect   15           auto   auto 10/100BaseTX
Fa0/5                        connected    15         a-full a-100 10/100BaseTX
Fa0/6                        notconnect   15           auto   auto 10/100BaseTX
Fa0/7                        notconnect   15           auto   auto 10/100BaseTX
Fa0/8                        notconnect   15           auto   auto 10/100BaseTX
Fa0/9                        notconnect   15           auto   auto 10/100BaseTX
Fa0/10                       notconnect   15           auto   auto 10/100BaseTX
Fa0/11                       connected    trunk      a-full a-100 10/100BaseTX
Fa0/12                       connected    trunk      a-full a-100 10/100BaseTX
Gi0/1                        connected    trunk      a-half a-100 100BaseBX-10U SFP
Gi0/2                        connected    trunk      a-half a-100 100BaseBX-10D SFP
Switch#sh interfaces gigabitEthernet 0/2
GigabitEthernet0/1 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet, address is c025.5c11.928d (bia c025.5c11.928d)
Description:
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
     reliability 254/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive not set
Half-duplex, 100Mb/s, link type is auto, media type is 100BaseBX-10D SFP
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 80000 bits/sec, 22 packets/sec
5 minute output rate 16000 bits/sec, 16 packets/sec
     74931 packets input, 21611558 bytes, 0 no buffer
     Received 48734 broadcasts (39982 multicasts)
     0 runts, 0 giants, 0 throttles
     667 input errors, 667 CRC, 0 frame, 0 overrun, 0 ignored
     0 watchdog, 39982 multicast, 0 pause input
     0 input packets with dribble condition detected
     23385 packets output, 3857612 bytes, 0 underruns
     0 output errors, 564 collisions, 1 interface resets
     0 babbles, 29 late collision, 0 deferred
     0 lost carrier, 0 no carrier, 0 PAUSE output
     0 output buffer failures, 0 output buffers swapped out

Yes scope all connections with a 900 micron 200x scope, and clean anything you can.
GLC-FE-100BX-U
100BASE-BX10-U
-8
-14
-3
-28.2
GLC-FE-100BX-D
100BASE-BX10-D
-8
-14
-3
-28.2
If its clean, check the TX/RX power levels with a power meters. End-to-end; bidirectional test, on both lamdas.
Because of the CWDM going on, I'm not sure I'd trust the internal "show hard" or
"show interfaces interface-id transceiver detail" internaly.
Obviously this is something common/systemic since it happens betwen multiple locations.
Is the fiber the common denominator?

Issues with CWLMS 3.2 RME 4.3.1 cannot fetch vlan.dat off a VSS and 4510.

Hi,
I am having a major headache with RME collecting the vlan.dat from a VSS and 4510, the device and credentials work fine, however when archiving the config i get partial success due to vlan failing. You can see in the IC_Services log that it attempts to TFTP the .dat file off which it fails with, i believe vlan fetch is only supported by SSH or telnet
when you do a CDA test both devices pass on everything..

managed to log on and please see below, tftp on one device works fine but from the 4510 or vss still fails
GRA_CHUB_CR_01#copy cat4000_flash: tftp:
Source filename []? vlan.dat
Address or name of remote host []? 172.20.220.10
Destination filename [vlan.dat]?
%Error opening tftp://172.20.220.10/vlan.dat (Timed out)
GRA_CHUB_CR_01#
DAR_R002_AS_01#
DAR_R002_AS_01#copy flash:vlan.dat tftp:
Address or name of remote host []? 172.20.220.10
Destination filename [vlan.dat]?
616 bytes copied in 0.009 secs (68444 bytes/sec)
DAR_R002_AS_01#

My 5s screen is super zoomed in and I cannot operate it?

My iPhone 5s screened is super zoomed in and I cannot operate it? any thoughts out there?

Double-tap the screen with THREE fingers. Then navigate to Settings/General/Accessibility and turn off Zoom.

Basic questation about VSS and windows backup

hi all, basic questation about backup and VSS
Environment:
windows 2008r2,NAS backup disk connected with iSCSI
If i create in the windows backup server job , where i backup disk D , target is NAS disk and start it . Windows backup is requester and is created shadow copy . This shadow copy is created in the disk D or in the NAS disk ? If in the disk D is created for
everyone application snapshot ? After created snapshot the windows backup copy data from snapshot to windowsimagebackup ? And If windows backup create different snapshot how detect which files is changed ?
thank you
Falcon

Hi,
Windows Server Backup stores backup versions in volume shadow copies. After the data write is complete, Windows Server Backup creates a shadow copy of the volume where the backup is stored using Volume Shadow Copy Service (VSS). This shadow copy retains the
state of the storage volume as a “backup version” or “point-in-time” of the backup and must restore using this backup version.
You could refer to the article below to know the steps of a back up operation performs:
Backup Version and Space Management in Windows Server Backup
http://blogs.technet.com/b/filecab/archive/2009/06/22/backup-version-and-space-management-in-windows-server-backup.aspx
Windows Server Backup uses Volume Shadow Copy Service (VSS) and block-level backup technology to back up and recover your operating system, files and folders, and volumes. The Volume Shadow Copy Service is used to differentiate between backup sets, and to track
where the various blocks are being written to within the shadow copy storage.
For more information about the incremental backup technology, please see:
Learn more about system image backup
http://blogs.technet.com/b/filecab/archive/2009/10/31/learn-more-about-system-image-backup.aspx
Backup and Recovery Issues with Windows Server 2008 (Part 2)
http://www.windowsnetworking.com/articles-tutorials/windows-server-2008/Backup-Recovery-Issues-Windows-Server-2008-Part2.html
Please Note: Since the website is not hosted by Microsoft, the link may change without notice. Microsoft does not guarantee the accuracy of this information.
Best Regards,
Mandy
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

VSS and Infoblox

Hi !
We have 2 Infoblox in HA connect to a VSS and we recibe this log:
[2013/01/10 17:47:03.945] (24443 /infoblox/one/bin/clusterd) vrrp.c:1180 vrrp_process_receive_pkt(): DETECTED DUAL ACTIVE CONDITION!
The configuration on the VSS's interfaces are:
interface giga1/1/YY
des LAN 1
sw acc vlan X
spanning-tree portfast
speed 1000
duplex full
interface giga1/1/YY
des HA1
sw acc vlan X
spanning-tree portfast
speed 1000
duplex full
interface giga2/1/YY
des LAN 2
sw acc vlan X
spanning-tree portfast
speed 1000
duplex full
interface giga2/1/YY
des HA2
sw acc vlan X
spanning-tree portfast
speed 1000
duplex full
All the interfaces are connected but the infloblox shows an error on the HA2 port.
Thanks
Regards,

Yes, we resolved the issue. There was any bug in the VSS IOS but when we change the status Master-backup the vip dind't learnt the new mac.
We configured the mac on the two interfaces manually.
Thank you,
Regards

10G-Ethernet RJ45 (10GBASE-T) and direct attached SFP+ Twinax (10GBASE-CR)?

Hello,
I'm searching a switch that does support 10G-Ethernet RJ45 (10GBASE-T) and direct attached SFP+ Twinax (10GBASE-CR).
I do not have big requirements, but it should be as cheap as possible.

Would like to connect an SFP+ port to 10GBASE-T port?
Maybe a media converter is enough for your demand.

Super sensative keyboard and keep putting my phone on mute or on speaker while on a call. What can i do?

Suddenly my iphone has a super sensative keyboard and keep putting my phone on mute or on speaker while on a call. What can i do?

Do you have a screen protector? If so, try removing it and see.
You can also try cleaning your screen with a lint free cloth, pretty much the same way you clean your glasses.

HT4528 I have an iPhone 5, and when i try to set a picture as my background it super enlarges it and will not let me shrink it down to the size it needs to be. help.

I have an iPhone 5, and when i try to set a picture as my background it super enlarges it and will not let me shrink it down to the size it needs to be. help

Hello Tholc
The reason for that is the screen motion that is enabled. With certain photos and how they were taken, they will be zoomed in so that there is no black space on the photo.
iOS 7: How to reduce screen motion
http://support.apple.com/kb/HT5595
Regards,
-Norm G.

4500x VSS and SFP-H10GB-CU1M

Hello
I have (2) Cisco 4500x with a VSS config. I als have a couple cables "SFP-H10GB-CU1M".
I want to make sure I have this physically setup correctly. I have searched but not found anything specific enough.
Please review and advise.

Yes, all device packages are installed (including 7.0) and the Pi 2.1.2 patch.
Info from "ifm_config_archive.log" when trying Archive the Configuration:
[2014-12-09 19:58:11,300] [pool-37-thread-5] [service] [ERROR] - Thread Id : [9,460] : IFM_CONFIG_ARCHIVE_ERROR_DETAILS: [Error in fetching VLAN file] : IFM_CONFIG_ARCHIVE_ERROR: [com.cisco.ifm.config.archive.service.exceptions.XDEFeatureExecutionException: No device package found for the specified device.]'
Maybe the Prime don't know where to find the vlan.dat on the 4500X-VSS ?
#dir cat4000_flash:
Directory of cat4000_flash:/
1 -rw- 2236 <no date> vlan.dat
sysObjectID (1.3.6.1.2.1.1.2) is
.iso.org.dod.internet.private.enterprises.cisco.ciscoProducts.cat4xxxVirtualSwitch
That is not the expected and supported value "4500X-16" above
Update: Error on fetching running and startup config as well:
[2014-12-09 20:24:21,818] [pool-37-thread-9] [service] [ERROR] - Thread Id : [10,013] : IFM_CONFIG_ARCHIVE_ERROR_DETAILS: [Error in fetching RUNNINGCONFIG file] : IFM_CONFIG_ARCHIVE_ERROR: [com.cisco.ifm.config.archive.service.exceptions.XDEFeatureExecutionException: No device package found for the specified device.]
[2014-12-09 20:25:31,882] [pool-37-thread-9] [service] [ERROR] - Thread Id : [10,013] : IFM_CONFIG_ARCHIVE_ERROR_DETAILS: [Error in fetching STARTUPCONFIG file] : IFM_CONFIG_ARCHIVE_ERROR: [com.cisco.ifm.config.archive.service.exceptions.XDEFeatureExecutionException: No device package found for the specified device.]

WS-X6748-SFP and 100Base-X

Hello.
Our network is based on Cisco7600 with WS-X6748-SFP modules.
As optical transceiver we use gigabitethernet GLC (1000Base-X).
In order to reduce costs can we use Fastethernet GLC 100Base-X?
Thx

Nope, that won't work. You need to use the 1000Base-X transceivers.
-brad
www.ccbootcamp.com
(please rate the post if this helps!)

6500-VSS and NEXUS 56XX vPC interoperability

Hello, is it possible to establish a PORT CHANNEL between a couple of Cisco 6500 running VSS mode and a couple of NEXUS 5000 running vPC? . Design should be " Back-to-Back" : VSS-- Port-Channel--vPC.
I want also to support L2 and L3 flows between the two couples.
I read many forums but i am not sure it runs.
Is such design, if it runs; supported by Cisco?
Thanks a lot for your help.

Hi Tlequertier,
We have VSS 6509Es with Sup 2Ts & 6908 modules. These have a 40gb/sec (4 x 10gb/sec) uplink to our NEXUS 5548UP vPC switches.
So we have a fully meshed ether-channel between the 4 physical switches (2 x N5548UP & 2x6509E)
Kind regards,
Tim

6509e SUP-2T VSS and 100BASE-X SFP

Similar Messages

Maybe you are looking for