6547E Max C dram BIOS settings

I have one stick of Samsung PC 2700 DDR ram, and can
only get it to reliably run @ 230 mhz.
I'm running P4 2 Ghz @ 2.3 Ghz without a problem, but when I try any CPU:Dram ratio besides 1:1 my system
locks at POST ;( .
Shouldn't I be able to run pc 2700 @ 333 Mhz?
Here are system/bios settings:
P4 2 Ghz CPU FSB @ 115 for CPU speed of 2.3 Ghz.
(runs @ 60 c and stable)
Core voltage @ 5.25v
Samsung 512 Mb DDR PC2700
CPU: DRAM ratio @ 1:1 for a DRAM frequency of 230 Mhz.
( anything else and I lock up @ POST)
Cas Latency @ 2.5
Timing @ turbo
Host dram @ fast
Graphics window @ 128
Generic 450w PSU
So wassup? My comp runs OK at these settings but I'm
just wondering why I can't reach 333 Mhz with the
Ram I have.

Quote
Core voltage @ 5.25v
I don't think so...
Is this a Williamette or Northwood CPU ?
Does the memory run wel at 333MHz if you don't overclock the CPU?

Similar Messages

Ideal BIOS Settings for online gaming

this is my 1st computer that i built. i have a lot of experience in wiring high-end electronics, so wiring this little rig with barely any visible wires/cables was a breeze. I bought the processor/mobo with the intention of only doing minor O/C as i dont really know all that much on the hardware side of improving performance. with that said, i've searched for timings and settings for my specific combination, and i cant find any. again, i dont really want to push the config past a safe level, as i will be selling this machine when the 64's come down in price. can someone help me set the proper frequencies/timings? i have a lot to learn, and even in the normal bios settings i don't know if certain things should be enabled or disabled for my main purpose, which is to simply play 3D online games very fast. i will be changing out the GeforceFX5200 PCI for a 5600 AGP in a week or so. I'm noticing that my old Comcrap PIII 1.0Ghz w/512SDRAM with this video card gets just as good a ping ingame as this rig does. the machine starts quickly, runs offline programs quickly, but online it isnt as fast as i'd hoped. from what i've read in the other forums, there are many settings in the bios that are enabled by default that don't need to be. can someone help me decipher which settings are useful and which are not. i loosely understand some of the settings but if someone could help with the questions below and/or do a walkthru for bios geared toward gaming i'd really appreciate it. The machine runs very cool (CPU 104*F/SYS 93*F) but i dont know what else needs adjustment. I simply want to make this machine go as fast and as hard as it can with the right config. i don't want to unlock the processor yet or do anything else major at this point.
1: Best yet safe Voltage for my processor and RAM
2: FSB clock; 133 or 166? had problems @ 200
3: S.M.A.R.T. on or off?
4: Best IRQ/PCI slot for video card
5: "GoodMEM" utility: how much should i safely allot?
6: Video BIOS Cacheable?
7: Multiplier setting for K7N2DeltaL & XP2600+
8: VGA Aperture (my card is 128MB but PCI. upgrading soon)
i'll be learning more as i go along, so i dont really need a full explanation of what's what, lol THIS TIME. all i need is a rundown where someone tells me what to leave alone, and what to change for a very fast yet safe gaming rig

OK I'm officially confused.
I bought the retail boxed AthlonXP2600+, which clearly states on the packaging "With 333 MHZ Frontside Bus". i bought the board over others, one reason being it supported 400MHz FSB. I go into "Advanced Chipset Features" and when i set the "System Performance" to "Manual", i can then go into the "CPU FSB Clock" settings, but the max it will allow me to go to is 233MHz (which won't boot and i have to flip the jumpers. when i had set it to 200MHz before, it failed to boot as well... PLEASE can someone look over these settings and tell me the OPTIMAL settings for taking this combo as fast as it can go w/o overclocking? What am i doing wrong? what multiplier do i need to be at. I'm under the impression that the combo works best when the clock speed of the board is at the same speed as the processor. here are the BIOS settings with which i need advice:
ADV. BIOS
Virus Warning [Disabled]
External Cache [Enabled]
Quick Boot [Enabled]
1st Boot [Floppy]
2nd Boot [HDD]
3rd Boot [CD]
Boot Other Device [Enabled]
Swap Floppy [Disabled]
Seek Floppy [Enabled]
Boot Up Num Lock LED [On]
Gate A20 Option [Fast]
Typematic Rate Setting [Disabled]
Security Option [Setup]
APIC Function [Enabled]
MPS Table Version [1.4]
BOOT OS/2 for DRAM>64MB [No]
HD S.M.A.R.T. [Enabled]
Video BIOS Cacheable [Enabled]
ADV. CHIPSET
System Performance [High Performance]
CPU FSB Clock [166MHz]
AGP 8x Support [Enabled]
AGP Fastwrite Support [Enabled]
System BIOS Cacheable [Disabled]
Video RAM Cacheable [Enabled]
AGP Aperture Size [128MB]
I do currently have a PCI GeForceFX5200 8o, but im getting an AGP FX5600 this week. i know my card has nothing to do with AGP, but i've left most of the AGP settings alone since i'll be using it later. is this creating a bottleneck or tying up system memory to have it this way for now?
FREQUENCY/VOLTAGE CTRL
AGP Clock Value [Default]
xAGP Clock Value [66]
AGP Voltage Adjust [1.5V]
DRAM Voltage Adjust [2.7V]
CPU Ratio [By H/W]
CPU Vcore Select [By H/W]
PCI Clock Auto-Detect [Enabled]
Again, I have an 333MhzFSB Chip and a board that will support up to 400MhzFSB. help!

Need help with bios settings for Neo4 Platinum

Hi. I've checked several guides on bioses and still have questions about my settings. I'm not an overclocker, so I'm looking for stability over anything else (although I don't want my computer to run like a pig . I'll post what I have and the parts of the bios that I'm unsure of. I also have saved pictures of a Cpu-z scan if that helps. Any suggestions are much appreciated!
Here's my stuff:
Motherboard: MSI K8N NEo4 Platinum (MS-7125)
Processor: AMD Athlon 64 3000+ 512K 90nm (Winchester socket 939)
   clock frequency: 1800mhz
   system bus: 2000
   operating mode: 32/64
   voltage: 1.40v
   max temp: 70 degrees C
   thermal power: 89w
   L1 cache: 128KB
   L2 cache: 512KB
   cmos technology: 90nm SOI
   memory controller: 128-bit
Award bios version: 1.9
Installed ram: Micron Crucial Ballistix 512MBx2 (1024MB total) (Crucial
part number BL6464Z402)
   PC3200 400mhz Dual-Channel DDR Dimm (184 pins)
   configuration: 64Meg x 64
   unbuffered/non-ecc
   voltage: 2.8v
   memory timings:   2-2-2-6
Here's my current bios settings (I've only listed sections that contained settings that I was unsure of):
ADVANCED BIOS FEATURES
quick booting: enabled
boot to os/2: no
ioapic function: enabled
mps table version: 1.4
full screen logo display: disabled
seek floppy: enabled
typematic rate setting: enabled
typematic rate: 30
typematic delay: 1000
security option: setup
ADVANCED CHIPSET FEATURES
--->>DRAM CONFIGURATION
timing mode: manual
memclock index value: 200mhz
cas# latency TCL:2
min ras# active time TRAS: 6t
ras# to cas# delay TRCD: 2t
row precharge time TRP: 2t
row to row delay TRRD: auto
row cycle time TRC: 8t
row refresh cyc time TRFC: 11t
read-to-write time TRWT:auto
write recovery time TWR:auto
write to read delay: TWTR:auto
refresh period TREF:auto
user config mode: auto
x bottom of 32-bit [31:24] io: D8
x 1t/2t memory timing: 2t
x read preamble value: 8ns
x async latency value: 9ns
s/w memory hole remapping: disabled
mtrr mapping mode: continuous
PNP/PCI CONFIGURATIONS
primary graphic's adapter: first pcie
resources controlled by: auto (escd)
x irq resources setup: press enter
maximum payload size: 4096
CELL MENU
current cpu clock: 1810 mhz
current ddr clock: 201 mhz
high performance mode: manual
aggressive timing: disabled
dynamic overclocking: disabled
adjust cpu fsb frequency: 200
ht frequency: 5x
ht width: (down arrow 16/up arrow 16)
cpu spread spectrum: disabled
sata spread spectrum: disabled
pcie spread spectrum: disabled
pcie clock: 100 mhz
sse/sse2 instructions: enabled
cool'n'quiet: disabled
adjust cpu vid: startup
extra cpu voltage: by cpu vid
cpu voltage 1.400v
memory voltage: auto
nf4 voltage: 1.50v
Thanks again. xpfshost

I'll do that, thanks. I guess I'm really mostly clueless about the following items:
memclock index value: 200mhz
row cycle time TRC: 8t
row refresh cyc time TRFC: 11t
current cpu clock: 1810 mhz
current ddr clock: 201 mhz
adjust cpu fsb frequency: 200
ht frequency: 5x
ht width: (down arrow 16/up arrow 16
pcie clock: 100 mhz
Do they look OK?? Thanks!
xpfshost
Quote from: Grayone on 19-April-07, 05:13:03
Change your user config mode in dram configuration to manual and change your memory timing to 1T. The 1T setting will speed up your memory slightly.

New Computer locks up then loses some bios settings

I just built a new system with the following pieces
2.40 gigahertz AMD Athlon 64 4000
Board: MS-7025
Bus Clock: 200 megahertz
BIOS: Phoenix Technologies, LTD 6.00 PG 02/17/2005
4x 512meg samsung
NVIDIA GeForce 6800 GT bfg oc agp
Thermaltake Silent Purepower 480W
NVIDIA STRIPE 372.62G [Hard drive] (400.09 GB) -- drive 0
photosmart printer card reader (HPH11) [Hard drive] -- drive 2
PLATINUM 080G 2F5400 USB Device [Hard drive] (81.96 GB) -- drive 1
Occasionally system will have a hard freeze and require a reboot. When this happens some of my bios setting change (agp becomes pci, I have to setup raid0 again and video card memory becomes 128). This does not happen after a normal startup and no other changes occur i.e. time and date are not reset. Thanks for any help.
Clint

You lose of bios settings is classic lack of power. The 12v output for Thermaltake Silent Purepower 480W is only 18a MAX, meaning you will essentially run @ about 12a under normal conditions. This isn't enough power for the Neo 2, which likes good clean power in the 24a range.

BIOS settings: please help

Hello,
You can see my specifications below.
I have been busy for weeks with my graphic card to reduce it's crashing.
Now I hope that someone, seeing my specifications below, might be so kind to help me
with the system BIOS settings, who are still at "default values".
I do video editing, burning etc. but no gaming.
I don't intend extreme over clocking.
I have removed the NB-fan as reducing noise is important to me.
Could someone give me some system BIOS settings and values,
for a good performance.
tia
Azerty

Seems we do something similar. See my signature for details. For me, it
worked out better to use 5:4 rate and to increase overclock the CPU only,
because MPEG2 encoding seems still to be CPU bound and mem performance
is not that big issue. The increase of speed is aproximately the increase of
CPU performance.
To enable 5:3, you have to set DRAM timing from AUTO to 333. Still a clock
rate like 227 in my case is x15 fot the CPU but x4 /5 for the RAM, giving you
some potential with DDR400 RAM. In my case, the Corsair allow me 2-3-2-5-8
at the rate.
For me, setting ram timings to SPD allows the MB to do a lot of nasty things.
MSI is somewhat nasty anyhow. 200 MHz FSB is 203. To get something like 200,
you have to set it to 201. I prefer manual settings. PAT is enabled and disabled
just like the board wants. A lot of different behaviours for different settings
and BIOS versions. I use 1.8. Here, PAT is alwasy disabled in 1:1 when you
set RAM timings manually. When setting it SPD, it will be on in Fast and up.
For me, PAT is switched on in 5:4 even in manual. Some say, in 5:4, PAT
can never be enabled. But for encoding, I saw no difference. For cutting, also.
Disable spectrum spread. Let PIC/AGP work at 33/66 fixed. To ackomplish this,
you might have to enable SATA, even if you don't use it. It's a bug. If you
anable Parallel only, you can set "keep yes fpr Serial" in IDE settings. Look for
other hints in this forum. (Sorry, just saw in your sig that you have SATA).
For the fan: I asked the question and a lot of people said it's no recomended to
simply switch off the fan. So I decided to by a cheap manual fan control. I use
it to reduce NB fan to minimum, so I nearly not hear it. I also have a case fan
that is alread reduced and reduced further by this control. The Zalman Cu
fan is also quite silent, I also reduce it. For cutting, no problems. CPU in idle
is about 35-38c (case 33c), will not go beyond 40-42c when cutting. When I do
encoding, it will raise. In this case I have to give aprox. half throttle (I normaly
leave the room for some 12-15 hours of encoding 90 minutes CBR 6500 and
switch them to full). Otherwise temps will raise to 60c (and crash). With a bit of
fan, they will stay at around 50c, which is ok.
If you have further questions, you can also email me.

BIOS settings for a AMD 2100+ in K7N2 Delta ILSR

Hi can some one tell me what i set the bios settings too for a AMD 2100+ and PC3200 DDR ram in the bios of a K7N2 Delat ILSR.
I dont want to over clock the system just run it at the stock speeds.
Cheers

set FSB to 133 and FSB/Dram ratio to 1:1 you will be underclocking your ram but you will get more peformance running in sync

Ideal KT4V BIOS settings for XP2500+ Barton

I've read AMD's recommendations for the KT4V BIOS settings http://www.amdforums.com/showindex.php?s=&threadid=186506 , but they seem to be very generic. I would like to know the settings that would give me the highest performance, without causing any instability, using my present system and usage. My son does 3D animation and gaming on this computer. This is a stand alone computer (no network). The latest version BIOS for the KT4V offers an option in Power Management Features to enable CPU HALT Command Detection. I heard that this would work better than Cooler XP in cooling the CPU. I enabled it and my CPU Temp dropped 6-10 degrees C. Is this recommended? What is the down side of this action? My system is as follows: AMD Athlon XP 2500+ w/ Vantec VA4-C7040 CPU fan (w/Arctic Silver 3) MSI KT4V mobo Gainward Golden Sample Ti/450 TV w/ 128MB DDR (GeForce3 Ti 200) 2 - Kingston 512MB PC2700 DDR RAM Antec TRUE550 power supply 1 - 40GB 7200RPM hard drive 1 - 30GB 5400RPM hard drive 1 - CD-ROM 1 - CD-RW 1 - floppy drive Windows XP home Any help would be appreciated. Thank you, Barry

As a result of my research, these are the BIOS settings that I am using. My computer runs well and is stable.
* MSI KT4VL BIOS SETTINGS w/AMD XP 2500+ w/ Barton *
==================
Standard CMOS Features
==================
Time Set Correctly Upon first POST and after each BIOS Flash / CMOS Reset
Date Set Correctly Upon first POST and after each BIOS Flash / CMOS Reset
Primary IDE Master
Type AUTO
32Bit transfer Mode ON
Primary IDE Slave
Type AUTO
32 Bit Transfer Mode ON
Secondary IDE MasterType AUTO
32 Bit Transfer Mode ON
Secondary IDE Slave
Type AUTO
32 Bit Transfer Mode ON
Floppy Drive A Set Appropriately
Floppy Drive B Not Installed
Boot Sector Virus Protection Disabled
===================
Advanced BIOS Features
===================
Quick Boot Enabled
Full Screen Logo Show Disabled
Boot Sequence
1st Boot Device Floppy
2nd Boot Device CDROM/DVD whatever you use
3rd Boot Device IDE 0
Try Other Boot Devices No
S.M.A.R.T. for Hard Disks Enabled
BootUp Num-Lock On
Floppy Drive Swap Disabled
Floppy Drive Seek Disabled
Primary Display VGA/EGA
Password Check Setup
Boot to OS/2 No
Internal Cache Enabled
System BIOS Cacheable Disabled
C000,32k Shadow Disabled
APIC Function Enabled
MPS Table Version 1.4
=======================
Advanced Chipset Features
=======================
DRAM Timing Control
Current Host Clock Displays current FSB Frequency
Configure SDRAM Timing By SPD (Set to User first to change RAM timings)
SDRAM frequency 333 for PC2700 and above
SDRAM CAS# Latency 2
Row Precharge Time 2T
RAS Pulse Width 5T
RAS to CAS Delay 2T
SDRAM Bank Interleave 4-Bank
SDRAM Burst Length 8QW
SDRAM 1T Command Enabled
Fast Command Fast (start here and if Windows installs stable set to Ultra)
Fast R-2-R Turnaround Enabled
AGP timing Control
AGP Mode 4X
AGP Fast Write Disabled
AGP Aperture Size 256MB
AGP Master 1 W/S Write Enabled
AGP Master 1 W/S Read Enabled
AGP Read Synchronization Enabled
PCI Delay Transaction Enabled
========================
Power Management Features
========================
IPCA Function Yes
ACPI Standby State S1/POS
Call VGA at S3 Resuming Disabled
USB Wakeup From S3 Enabled
Power Management/APM Enabled
Power/Sleep LED Single LED
Suspend Time Out (Minute) Disabled
Display Activity Ignore
CPU Critical temperature 70 degrees C CPU HALT Command Detection Disabled
Power Button Function On/Off
After AC Power Loss Power Off
Set WakeUp Events
Wake Up on Ring Disabled
Wake Up on PME Disabled
Resume On KBC Disabled
Wake Up Key Any Key
Wake Up Password N/A
Resume on PS/2 Mouse Disabled
Resume By Alarm Disabled
Alarm Date 15
Alarm Hour 12
Alarm Minute 30
Alarm Second 30
===================
PnP/PCI Configurations
===================
Plug and Play Aware O/S Yes
Clear NVRAM No (Set One time only to Yes After Installing New Hardware or Moving PCI Cards Around)
PCI Latency Timer 64 (Set Higher for better PCI performance reduce if having sound or LAN problems)
PCI IDE BusMaster Enabled
Primary Graphics Adapter AGP for AGP card - PCI for PCI video card)
PCI Slot 1 IRQ Auto
PCI Slot 2/5 IRQ Auto
PCI Slot 3/6 IRQ Auto
PCI Slot 4 IRQ Auto
===================
Integrated Peripherals
===================
Floppy Disk Controller Auto
Serial Port 1 Disabled
Serial Port 2 Disabled
Serial Port 2 Mode Normal
IR Pin Select IRRX/IRTX
Onboard Parallel Port Auto
Parallel Port Mode ECP (For some Printers you may need to set as Bi-Dir or EPP)
EPP version N/A
Parallel Port IRQ Auto
Parallel Port DMA Auto
Onboard Midi Port Disabled
Onchip IDE Controller Both
Onboard LAN Enabled (Disabled if using PCI LAN card)
Onboard LAN PME Enabled (Disabled if using PCI LAN card)
AC’97 Audio Enabled (unless using PCI sound card)
MC’97 Modem Disabled
USB Controller All 6 USB Ports
USB Legacy Support Disabled (some people with legacy USB devices may need to enable)
Port 64/60 Emulation Enabled
===============
PC Health Status
===============
Chassis Intrusion Disabled
CPU Fan Detect Enabled (set to disabled BEFORE shutting down to install any PSU powered CPU fan)
======================
Frequency/Voltage Control
======================
Spread Spectrum Disabled (return to default setting to troubleshoot EMI problems)
CPU FSB Clock 166
CPU Ratio Auto
CPU Vcore (V) Auto
DDR Voltage (V) Auto (set to 1.6 if you have RAM instability)
Termination Voltage Auto
AGP Voltage (V) Auto

MSI 865PE-LS O/C & best Bios settings help

I would like to know the bios configuration for meory,cpu setting
voltage and latency to run
MSI 865PE LS Neo2 Bios Vs 1.52
2x Apacer 512mb DDR400 Powerchip (P/N:77.10739.634
to the best perfromance
any help would be appreciated
see specs below

(jpscwf) going by all the threads it would be better to use 1.5 or 1.52b and the other bioses I have are unknown
I need all the latency settings and good bios settings to run my memory etc
any ideas on the best performance and stable O/C setting
Example
Core Volt -
DRAM Volt -
DRAM timings -

Bios Settings for AMD 2500+

Hi Guys,
I've just built a new system with a KM"M Combo series MSI motherboard. I've put an AMD 2500+ CPU in and set the bio settings all to default, however the CPU is shown as a 1700+ and then in Windows XP the actual speed is shown as being 1400+ Can anyone tell me which settings I need to change and to what.
Thanks.

KM2M uses a 133/266FSB max, the 2500 is a 333FSB CPU. you will never get it up to full speed on that board. Either swap it for a 2600 266FSB chip (good luck finding the rare critter) or a 2400. the 2600 has 3 versions, 1 @ 266, and 2 @ 333. All 2400's are 266FSB.
The other option is to run it at the speed it is running now, and knowing that you are underclocking it about 20%.

URGENT HELP NEEDED (Bios Settings Failed)

Hey Guys,
I am having problems with my MSI Board, and don't know what to do. I am very much a noob to BIOS/and modding so I apologize in advance. You guys helped me a few months ago getting everything up and running and all was great for months. Then last night I walked away from my PC for a while and when i came back a starting screen was on saying my OC Settings Failed to load, i tried other versions I saved and they all failed as well. I ended up loading failsafe options, and got the "double start" where the computer turns on, then instantly shuts off, then turns on again. This allowed me to load windows 7, which then started to "install updates". So i think while i was away Windows automatically updated and rebooted... but would that effect my BIOS settings?
As I said, I had my system running perfect for months no errors or crashes at all based on the Bios setting you guys help me with in this thread: https://forum-en.msi.com/index.php?topic=147854.0
However, last week I removed the heat sink and installed this cooler: http://www.newegg.com/Product/Product.aspx?Item=N82E16835181010&nm_mc=OTC-Froogle&cm_mmc=OTC-Froogle-_-Water+Cooling-_-Corsair-_-35181010
All I did was unhook everything from the MB, install the cooler, and then hook everything back up to the MB. The only thing I may have done wrong is not connect the SATA devices (my HDs and ROMS) back in the spots they were in originally. However after I installed the cooler, they system booted right up, and I haven’t had any problems with my system for the past two weeks. I also should note I didnt make any BIOS changes either after I installed the cooler. So I don’t know if I should have done something there. Yet, like I said the system has been fine for the past two weeks, no crashes or errors... it wasn’t until last night after Windows auto updated that this has begun.
The reason I need "URGENT HELP" is because of course I just a new job with deadlines due and so much video editing work I need to do. I would be fine leaving it on failsafe settings, and forgetting the OC setting all together if I new that would make the system stable. But considering its still doing the "double start" even in failsafe mode, im afraid if i start working my system will crash.
So I am begging anybody for any advice or help they could provide. I will provide my system info below. If anybody can guide me as to what settings I should set in BIOS i would appreciate it. Or perhaps there’s a BIOS update that I should use now that I have a cooler and not a heat sink? If you need any more information from me, just ask. I will be monitoring this thread all day, as I desperately need help.
MY SYSTEM:
Intel 980X chip running Win 7 64bit (with MSI BigBang xPower MB installed in my old Dell XPS 730X)
(1) SATA II WD 3gb Hard Drive @ 1.5TB
(2) OCZ SATA II SSD drives @120GB: http://www.newegg.com/Product/Product.aspx?Item=N82E16820227543
(2) Hitachi 6gb SATA III drives @2TB: http://www.newegg.com/Product/Product.aspx?Item=N82E16822145473
3 DVD/CD/BLUERAY DRIVES:
1 SATA DVD DRIVE
1 SATA BlueRay Drive
1 SATA CD Drive
(So 8 SATA Devices Total)
24GIGs of this ram: http://www.newegg.com/Product/Product.aspx?Item=N82E16820145321
1 NVida Geforce GTX 470
1 Soundblaster X-Fi Titanum Card
New Addition Water Cooler: http://www.newegg.com/Product/Product.aspx?Item=N82E16835181010&nm_mc=OTC-Froogle&cm_mmc=OTC-Froogle-_-Water+Cooling-_-Corsair-_-35181010

PROBLEM: My OC BIOS setting wont load. Even on failsafe i get the "double start". I want to get back to my OC (stable) settings.
UPDATE: Since I posted somebody messaged me mentioned I should have "reset the CMOS" after I installed the new cooler. So I did that, and now they system starts fine without the "double start". I am able to load one of my saved OC settings now as well (but any others causes a failure).
NEW QUESTIONS:
1. Since I reset the CMOS and now the system is starting fine on my last OC settings, is it safe to assume the sytem is stable for now?
2. I never made any power changes or BIOS changes after I installed the new cooler. Should I have?
3. After I reset the CMOS was I soupposed to reinstall the drivers from the MSI disk again? I did not, and the system seems to be fine, but I thought I was soupposed to do that after a CMOS reset.
4. Is there a new BIOS version for my setup that may be better now? Im currently on v1.5
Here is a screenshot from CPUZ of the system information currently. This is with it booting normally after my CMOS reboot. I just figured id post it incase it helps with any of my questions. Thanks so much for helping guys!

How to restore default BIOS settings on Toshiba 1410 / 1415 / 2410 laptops? Option to CHGBIOSA?

I have problems booting to any operating system but DOS on Toshiba Satellite 1410 (in very good physical condition) after few years of inactivity (drained down main battery and CMOS battery - now they're charged)
Windows stops with BSOD (error 0x0000008e), Linux stops with kernel panic, bad_area_nosemaphore and IRQ error.
Plain MS-DOS 7.10 seems to run OK.
BIOS was 1.40 with main password set. After first boot it displayed request for entering password and pressing F1 key to set the hardware clock. Now it doesn't display this message anymore.
Two memory modules (Nanya - 256 MB, 266 MHz, CL 2,5) are OK - checked on different versions of MemTest86+
(Windows Memory Diagnostic Tool hangs when starting!)
I dismantled laptop and cleaned very small amount of dust inside with compressed air. Changed thermal paste on the processor (Celeron M 1,8) and bridge. Turned laptop on with extension cards, battery and disk and without them also.
It didn't help.
I flashed the CMOS with BIOS 1.20, 1.30 and 1.40 back again. None of the versions didn't let booting neither Windows nor Linux.
MS-DOS, PC-DOS, FreeDOS still run OK.
What's more interesting - after flashing procedure all BIOS settings were intact (booting priority, battery saving mode, etc.). And yes - I removed the password before flashing!
I was suspicious about problems occuring when laptop was entering 32-bit mode and checked it with Video Memory Stress Test.
When CMOS was flashed with 1.20 BIOS above test was running flawlessly. However, with 1.30 and 1.40 version it stopped >>Unhandled Exceptopn "Access Denied"<< in 8th iteration when lucky. Most of the time it stopped after 2nd or 3rd iteration after framebuffer subtest.
So my question are:
- did CMOS lost its settings or somehow they were corrupted after long period of laptop's inactivity?
- is Video extension of this BIOS flashable?
- why the settings are NOT restored to defaults after each CMOS flashing?
- or maybe there is some hidden switch/option to CHGBIOSA flasher to reset non-flashable CMOS area?
- or is my built-in Video Card (nVidia NV17M) or IRQ enumerator dead?

Hi Jerry! I think I'm on board now, anyway I hope so. I removed both devices and switched them around. The device manager shows two USB devices. One is Mass Storage and one is Composite. I don't realy know which one is the 1TB and which one is the 16 GB. In my boot menu, it just says USB now?? My laptop only has three USB ports. Two on the right and One on the left. I have a wireless mouse plugged in one of the ports on the right as you can see in device manager. I hope this is what you were asking. I can be a little thick headed at times, so let me know what else you want me to try Thank you for your kind reply. It really means a lot to me.
Dokie!
I Love my Satellite L775D-S7222 Laptop. Some days you're the windshield, Some days you're the bug. The Computer world is crazy. If you have answers to computer problems, pass them forward.
Attachments:
Capture40.JPG ‏202 KB
Capture41.JPG ‏137 KB

How do I find the BIOS settings? I'm trying to install a VM so I can run CAD programs for my work.

I am an engineering student and thus having the capability to utilize CAD programs is highly advantageous to me, so I talked to several of my friends who have Macbooks and they recommended using Parallel. After I installed the program and my Windows OS, it keeps giving me an error message saying that the hardware virtualization has been disabled in the BIOS settings. I cannot find the BIOS settings anywhere! How do I change this? Does anyone know?

There are no BIOS settings, because Macs don't have a BIOS. I don't use Parallels, but I assume it has simulated BIOS settings. You'd have to consult its documentation to find out how to change them.

Lenovo G50-30 Unable to access BIOS settings after Windows recovery

Hi
I recently 'downgraded' a recently purchased Lenovo G50-30 with preinstalled Windows 8.1 to Windows 7 using a UEFI USB install on a GPT partition. I also updated the BIOS from A7CN40WW to the latest A7CN43WW and all was working fine. However, after performing a necessary restore of an system image created using the Windows 7 backup and restore tool, I am suddenly unable to access the BIOS settings, either with the novo button (I do get the menu to select BIOS) or with Fn +F2. All that happens is that I receive a blank screen with a static cursor in the upper left corner. I can however still access the boot menu Fn +F12. This is a particular pain as I obviousl can't select USB 3.0 in BIOS.
Any help here would be greatly appreciated.

OK, I managed to clear CMOS by disassembling and desoldering a leg off the the RTC battery but to no avail. The problem seems to be that BIOS a7cn43ww itself has somehow been corupted. In theory this should be able to be resolved by a reflash. The trouble here is there seems to be no way to reflash with a current or previous BIOS version, so I'll have to either wait for a newer version or someone may know better.
C'mon Lenovo support this simply isn't good enough. It's a brand new laptop and I'm considering returning it for a refund.

How to install Windows 7 in UEFI modeand what bios settings for D30

How do you install windows 7 in UEFI mode and what bios settings do I need to install it on a D30 workstation.

Not a ThinkStation guy, but FWIW, that can happen when installing Win 7 in UEFI mode when CSM support is not enabled in BIOS.
Is CSM support - either explicit or by selecting "other OS" and turning UEFI back on as suggested above - an option?
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

BIOS Settings Problem on KT3 Ultra2 MS-6380E with Barton 3000+(FSB333)

Well, I finally got my Barton 3000+ with 333 MHz FSB and installed it yesterday in my MSI KT3 Ultra2 Mainboard....
System Before changing anything:
PSU: DTK 400 W
+3.3 V / 22 A
+5 V / 35 A
+12 V / 15 A
-5 V / 0.5 A
-12 V / 0.8 A
+5 V VSB / 3 A
So that should make up 400 W as far as I know, my total System drain should be around 300-350 W so even if it would not suffice 400 W it should run the system ?
Mainboard: KT3 Ultra 2 (BIOS v5.7)
CPU: AMD XP 2100 FSB 133 MHz
RAM: 1.536 MB, 3x512 MB Infineon PC3200 (400MHz) CL 3-3-3-8 @400MHz, Cl2.5-3-3-7@333Mhz, 2-2-2-6@266MHz
VGA: MSI RX-9800 Pro 128 MB
DVD/CD-R/RW-Combo: Plextor PX-708 (Firmware 1.08)
CD-R/RW: TEAC CD-W540E (Firmware 1.0K)
Storage: Western Digital WD800BB (80 GB) (Firmware 17.07W17)
USB-Storage: Maxtor 4 K080 H4 (80 GB)
Monitor: Samsung Syncmaster 172T with Driver Version 1.0
Printer: HP Deskjet 970Cxi with Original HP Driver Version 4.3
OS: Windows 2000 Professional with Service Pack 4
BIOS Settings: SDRAM 1T Command: "Disabled" It won't work stable with 3 RAM's in it with that setting, but that I did know before.
CPU Fast Command: "Ultra"
System was running stable for nearly 2 years with this Configuration:
So now it goes:
First I changed the CPU form my old AMD XP 2100+ to the new Barton 3000 + with its new Arctic Cool Copper Silent 2TC.
Then I went into BIOS and raised the FSB to 166 MHz, which should be the correct one, or do I have to put 167 MHz in there (since 166.666666 MHz is rounded to 167)?
Then I exited and watched the restart...but it didn't start-up it only got me 3 long beeps at the HOST.
After some whining and beating I plugged out anything and cleared CMOS and started the whole thing again:
System after Clearing CMOS:
Mainboard: KT3 Ultra 2 (BIOS v5.7)
CPU: AMD XP 3000+ FSB 100 MHz
RAM: 1x512 MB Infineon PC3200 CL 2-3-3-7 (BIOS setting CAS Latency by "SPD")
Storage: Western Digital WD800BB (80 GB) (Firmware 17.07W17)
Monitor: Samsung Syncmaster 172T with Driver Version 1.0
OS: Windows 2000 Professional with Service Pack 4
With all Default settings, the Computer boots up, and is correctly Recognized as a Barton 1300 MHz.
When increasing FSB to 133 MHz it is correctly displayed as a Barton 2200+
NOW...
...after adding one BIOS setting after another I narrowed the problem down to the "CPU Fast Command (decode)" Function...if set to Ultra it does not boot-up when running 166 MHz FSB, it does not even let me into BIOS. I have to clear CMOS and restart from scratch again...
Is this normal and expectable with a Barton 3000+ running at the native 166 MHz FSB or not ?
Since my system before was running on "Ultra" with my old AMD XP 2100+.
There is only one more thing I noticed, the CPU V-Core is shown to be only 1.616 V (setting on "Auto" but it should be 1.65 V ? Should I increase the V-Core to 1.675 V in order to get closer to 1.65 V or shouldn't I worry about ?
Thanks for any Input you can give me on the problem.
Iscaran

Iscaran, you are indeed correct in the statement which you made
Quote
...after adding one BIOS setting after another I narrowed the problem down to the "CPU Fast Command (decode)" Function...if set to Ultra it does not boot-up when running 166 MHz FSB, it does not even let me into BIOS. I have to clear CMOS and restart from scratch again...
This setting can be set to fast/ultra on the KT3 Ultra2 when using PC2100 ram running at 266. However, when using PC2700 ram running at 333, this setting MUST be set to normal for the satisfactory operation of the board. I know that you have PC3200 ram actually installed but it is only running at 333.
Quote
Is this normal and expectable with a Barton 3000+ running at the native 166 MHz FSB or not ?
Yes, absolutely normal
Quote
There is only one more thing I noticed, the CPU V-Core is shown to be only 1.616 V (setting on "Auto" but it should be 1.65 V ? Should I increase the V-Core to 1.675 V in order to get closer to 1.65 V or shouldn't I worry about ?
How are you measuring this ie Bios or o/s utility? Not unknown that these are incorrect. However, if you feel unhappy about this, try setting the V-core manually to 1.65v and check what this gives.
Quote
So 3.3 V x 22 A gives 72.6 W, that could be really a little cutting the edge. Could that cause the board to not respond when setting the "CPU Fast Command" to "Ultra" ?
Getting a more powerful psu will not likely cure this well documented problem.
However, this board mostly draws power from the 3.3 & 5v rails. The 12v is mostly used to power HDD, optical and fans. When you consider that 128Mb of ram draws about 8-10w from the 5v rail and you have a total of 1.5Gb that adds up to 96-120W of juice just for the memory alone. This board will beep at you at o/s level when it's running underpowered but my opinion is the same as osnavi's your 3.3v & 5v rails are too low. Also what is combined 3.3v & 5v wattage. What kind of reading do you get on monitoring utilities.
By the way I have as you can see from my dets below the same board and cpu as you and when I changed from a XP2000 Palomino with PC2100 ram to XP3000 Barton and PC3200, I changed the 'Fast Command' setting from 'Fast' to 'Normal'
Hope this helps, enjoy the board

6547E Max C dram BIOS settings

Similar Messages

Maybe you are looking for