6555b System Board

I have a 6555b that is out of warranty and I need to change the system board out but before I do I want to make sure that I can change the S/N and the Model in the BIOS. Is there a way for me to change the S/N and the Model in the BIOS?

Hey simsj,
Welcome to the HP Forums!
I am sorry, but to get your issue more exposure, I would suggest posting it in the commercial forums, since this is a commercial product. You can do this at http://h30499.www3.hp.com/hpeb/
I hope this helps.
I worked on behalf of HP

Similar Messages

How can you brand a serial number onto the system board?

I just replaced a system board and need to brand it with the appropriate serial number. How do I accomplish that? I have software to run when I do that with Dells or Lenovos. How can I do it with an HP?

Hi:
You cannot tattoo a HP notebook. It has to be done by an authorized HP tech service center where they have a DMI tool for that which is not available to the public.
You can tattoo some HP business desktops with this software, link below. It might work on HP consumer desktops but I don't know since I have never tried it on one.
http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=12...
This program makes a bootable floppy disk, and cannot be installed via any other method than a FDD or USB FDD.
It works on many other HP business desktops other than those listed. It has been used successfully in PC's up to a couple years old.
Paul

Z77A-GD65 power issue/bad system board?

Looking for advice. I am afraid its a bad board, but some symptoms point at power which also makes no sense.
This is what the WHOLE system should look like.
MSI Z77A-GD65 system board
Intel 3770K 3.5Ghz
Anted Kuhler H20 620
G.Skills RipJaws 16GB 1600Mhz DDR3 F3-14900CL9Q-16GBXL (on the test list)
Asus nVidia GTX 680 video card
OCX Vertex 3 256MB SSD
Seagate 500GB data drive
Razer Lycosa Keyboard
Razer DeathAdder Mouse
Antec Sonata IV case with Neo ECO 620W power supply
It seems to me that 620W should be more than enough. According to my calculations thats roughly 330W of power draw against a 620W powersupply.
I am not currently over clocking.
So what the system does look like is:
If I connect the 500GB drive then windows starts rebooting as soon as the Windows logo comes up.
If I place all four sticks of RAM in the system windows starts rebooting as soon as the Windows logo comes up.
If I leave the 500GB standard sata drive off and only use 3 sticks of RAM... well we get a solid system and I am writing this message on it.
3 sticks of ram appear to work in any 3 slots and allow the system to boot, except 1,3,4. That combo also resulted in the reboots at the windows logo.
I first thought it was RAM, originally I was using Corsair Vengeance. I saw some posts here about people having the same problem, and noted that the Corsiar RAM was not tested and switch to a the tested G.Skill instead.
Any ideas? It does not completely seem like a System board issue, but it certainly should not be power. All heat levels are well within normal and as I said the system works great if I leave off the drive and one stick of RAM.
Thanks guys....

System torn down, and put back together. (Found out I was out of Thrermal Compound, so I had to run to the store to get some.)
No long leads, only 9 stand offs matching each mount point on the systemboard.
Back together... problem is the exact same.
However, back to the hard drive issue. I decided to play with that since I was getting no where with 4 sticks of RAM.
What I have discovered is that with NO sata cable connecting the drive to the system board, if I try to power the two 250GB standard sata drives the system reboots just as the Windows logo should come up.
The fact that this behavior is so close to the RAM behavior... I am back to thinking its a power issue, though system board is still a chance... its just easier to buy a new better power supply than the Antec Neo Power 620 that came with the case. (I have not ever had a problem with Antec before, and will likely just buy one of their higher end power supplies to replace it, but I think I will try it next, just in case.)
I am not seeing any strange behavior power wise as far as any monitor shows... but connecting power to a sata drive that is NOT connected with a sata cable and causing a reboot just screams power at me.
Anymore thoughts today. In the mean time off to play Secret World with just the SSD and two sticks of RAM, which still runs rock solid.

Replaced system board? How to restore system serial number with a CD.

I have an l412 with a defective system board- would not POST. So I replaced the system board (it's a year out of warranty) and booted up, only to be met with an error code about a sytem serial number mismatch. Boots OK, but system update does not work (because of the serial number mismatch).
The instructions for WHAT to do about this are in the online service manual http://download.lenovo.com/ibmdl/pub/pc/pccbbs/mobiles_pdf/60y3635_02.pdf
When the computer was manufactured, the EEPROM on the system board was loaded with the serial numbers of the system and all major components. These numbers need to remain the same throughout the life of the computer.
If you replace the system board, you must restore the serial number of the system unit to its original value.
You need the LENOVO ThinkPad Hardware Maintenance Diskette to do this. This floppy disk is only available to certified Lenovo service centers. Or those who know how to use google. Versions 1.75, 1.76 and 1.83 are the ones I have used. If you can't find them, you probably should not be trying this anyway.
You read that correctly- DISKETTE. As in floppy disk. How many laptops have one of these? Now you see the problem.
The real trick is HOW to do this- without a USB floppy drive. If you have one of these, stop, you don't need to know this.
For the rest of us....
First, find a computer with a floppy drive. Any computer.
Extract/install the HMD archive onto it. Follow the instructions in the file to make an HMD floppy disk.
Use this program http://www.boodaa.de/index.php/download-mainmenu-31/bootdisk2bootstick-mainmenu-44 to make an image of the floppy. Be sure to save it as a .img type, not .bin
Use this program http://paulski.com/zpages.php?id=1814 to create a bootable CD image using the floppy .img file you just made.
Burn the ISO to a CD and boot from it.
At least on my L412, it works!

you can only download the trial version unless you purchased from adobe and there's a link under your account, https://www.adobe.com/account.html

T 40 Yellow DC-in block on the system board part number

The DC conncector mounted on the system brd where the AC Adapter connects to the laptop. Does anybody know the part number for that. It is a failure I see in many of the t40 series laptop but I have not been able to locate a part number. It does not come with the system board.

Hi SRJack
Please find the link given below for your unit and the Manual and complete part number inside your unit might help you to fix your issue check page number 3-5.
Maintenance and Service Guide
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

IPhone5 bad system board

Yesterday my i5 was at 40% and i decided to plug it in which i noticed it wasnt charging so i rebooted the phone but it wouldnt power back on. I did a handful of hard resets and finally got the screen to show the 'plug in to charge' icon. Im thinking it was at 40% how can it be dead. I plugged it in and wouldnt charge. Tried several cables that worked on the ipad and still wouldnt work with the i5. So i took it in to a local phone repair which they stuck a new battery in and the phone booted but would not charge. They replaced the charge port and still wouldnt charge so they deemed it unrepairable and something wrong with the system board. This phone was bought in Oct 2012 so its about 1.5 yr old. Will apple fix this? whats the procedure on this since its out of warranty?

If the place that repaired the phone was Apple authorized:
If your iPod Touch, iPhone, or iPad is Broken
Apple does not fix iDevices. Instead, they exchange yours for a refurbished or new replacement depending upon the age of your device and refurbished inventories. On rare occasions when there are no longer refurbished units for your older model, they may replace it with the next newer model.
ATTN: Beginning July 2013 Apple Stores are now equipped to do screen repairs/replacements in-house on iPhone 5 and 5C. In some cases while you wait. According to Apple this is the beginning of equipping Apple Stores with the resources needed to do most repairs for iPhones, iPads, and iPod Touches that would not require major replacements. Later in the year the services may be extended as Apple Stores become equipped and staffed with the proper repair expertise. So, if you need a screen repaired or a broken screen replaced or have your stuck Home button fixed, call your local Apple Store to see if they are now doing these in-house.
You may take your device to an Apple retailer for help or you may call Customer Service and arrange to send your device to Apple:
Apple Store Customer Service at 1-800-676-2775 or visit online Help for more information.
To contact product and tech support: Contacting Apple for support and service - this includes international calling numbers.
You will find respective repair costs in the appropriate link:
iPod Service Support and Costs
iPhone Service Support and Costs
iPad Service Support and Costs
There are third-party firms that do repairs on iDevices, and there are places where you can order parts to DIY if you feel up to the task:
1. iResq or Google for others.
2. Buy and replace screen yourself: iFixit

What is the cost and process for factory refurbish of a tx2-1375dx with a blown system board?cc=us

What is the cost and process for factory refurbish of a tx2-1375dx with a blown system board?
How would one go about arranging for such service?
Why is it impossible to contact a real human for support, either via online chat or phone?

Last I checked I am a real human, it is just that I do not work for HP and can't speak for them. HP would not be the place I would go for a "refurbish" job. They charge an arm and a leg for out of warranty service. You simply need to find someone to replace the system board (motherboard). It is also very likely on that model that you could have your system board repaired. There are many services on ebay that will repair the motherboard at the component level. The cost would be at or under $100 or so. I have more advice to give but many times I write a detailed response only to have the user never come back. I do check my posts so if you want more ideas just please respond. The tx2-1000 was one of the models affected by the nVidia issue that caused so many HP laptops made in the 2007-2009 era to fail prematurely.

T420 Wearing System Board Insulation in Battery Compartment

From many insertions and removals of batteries, the insulation on the system board of my T420 has begun to wear under the battery (you can see it under the alignment tongue in the following photo). The wear is a bit more pronounced than visible in the photo.
Questions:
a)Is there anything of significance under the insulation (any circuit board components or traces)? Why is the insulation there?
b)If I finally wear through the insulation, are there any special electrical properties where I just can't patch it with clear laminating material (non-conductive) or something like this?
c)Does Lenovo sell this insulation as a spare part (I doubt it)? (And even so, I'd hate to tear the computer apart to replace it--this would take me a good 8 hours.)
d)Anything else I should know?
Thanks, Dave Ashley

A follow-up on this:
I spoke to Apple Australia who said it was not uncommon, even though AppleCare (in India) had said it was not something they had heard of and that I should speak to Customer Relations.
The repair person at the second Apple Store then advised me that the logic board serial no on some machines is in fact the factory's serial no, not Apple's, and therefore it is normal. There is confusion, though, since many newer machines have eg iBooks have Apple's serial no under the key pad.

IMac G5 not starting up after system board install

Six caps blew on my old system board so I ordered a new one and installed it. The system started up great and was running perfectly. However, after the 3rd or 4th reboot, there is no longer anything on the display. I can hear the power click on and after a few seconds, the fans usually start to sing.
I have reset the SMU several times. I have taken the cover off and checked that LED #1 is on when I plug in the power cord. When I push the internal power button, LED #2 comes on and stays lit. Still there is no display.
Can anyone make a suggestion as to what I might check next or what might be going on?
I feel like maybe I didn't get everything plugged in securely when installing the system board, but it was working initially. Any ideas?

It is quite possible that your replaced board is faulty, or that the caps on the power supply have now gone bad. Check every cap in the machine and see what you find.

Time Machine Issue with new system board.

OK MAC Fans here is an issue that I discovered with Time Machine (TM).
First I have a 17” MacBookPro that has two 1TB external HDs and a 30” monitor attached to it.
Something happened to my system and the system board had to be replaced.
The Mac was sent to TX and a new system board was put in it and the very latest OS (10.5.2) was installed on the hard drive.
The Apple store added my profile so you think everything would be good?
Wrong!
None of my applications made it through.
But I was thinking let just use Time Machine to restore them. WRONG in a way.
The first thing I did when I got home was set up TM. I pointed TM to the external HD that has all of the previous backup files and TM wanted to backup the system. During the backup I notice that TM created a new directory for the backup files.
The name of the directory was the name of my MAC. The old directory was also the name of my MAC but with the new OS software release it was stated that you could not use any special characters when naming your MAC or TM may not recognize your backup files (there is a note on this under support).
The new name is FirstnameLastnameMacBookPro17 the old name was Firstname Lastname’s MacBookPro 17”. TM created a new directory named FirstnameLastnameMacBookPro17 and this was the only files that are visible in TM.
I deleted the new directory and renamed my MAC back to the old name and TM created a NEW directory with the old name. Now there were 2 directories with the same “old” name. I can not get TM to use the old directory and display the old backup files.
I was able to drag and drop the files and applications I needed from the previous backup folders back to where I needed them to be so all is not lost but I can not restore files from TM.
Also I renamed my MAC back to FirstnameLastnameMacBookPro17 and TM automatically changed the name of the new directory to the new name.
I tried to drag old backup folders from the old TM directory to the new TM directory but received an error that the files can not be modified.
The only thing that I can think is that when the system board was replaced TM got confused and did not recognize it as the same system. So now I am starting my backup history all over again. The old backup files are good, the only thing is that I have to drag and drop items I want from those folders to the location I want. I can not use the old backup files in TM.
Dose any one have a magic pill (red or blue) I can take to make the old files visible in TM?

I decided not to worry about the syncing my TM. I was just at the Apple store and they have decided to replace my MacBookPro. I am going to start my backups on the new system all over again. I know I can drag and drop files that I want from the old files to the new system if I want and that will be go enough.

Question about moving system board from domain C to domain B SF2000

Hello,
i would like to move the system board e this is my configuration:
Domain A with Domain B Solaris 10 Sun cluster 3.2
Domain C Solaris 10 no Sun Cluster.
I move the sytem board SB7 from domain C to domain B with the command from System Controller:
# moveboard -d B -r 2 -t 900 SB7
This command can be done during normal operation and it's totally transparent to Sun Cluster domain A-B.
Thankls

The subject line of your post mentions a "SF2000".
Could you actually mean you have a Sunfire E20K ?
[http://sunsolve.sun.com/handbook_pub/validateUser.do?target=Systems/SunFireE20K_R/SunFireE20K_R]
If yes, then I suggest you contact your local Sun Support Center and open a proper support case.
Get assistance from engineers specifically available for such expensive systems.
This is just an anonymous user-to-user discussion forum.

Is is the BIOS or the system board?

Hi. I have a pc manufactued by a deceased company named Quantex. The pc has a MSI MS-6199VA
system board with W6199VAFD v3.3 121799 Bios, an Intel P6C (Coppermine) Pentium III 733Mhz
processor and a VIA Apollo Pro 133 chipset.
I have been having some trouble with the pc over the last month. It has an nVidia GeForce 256 video
card and around the middle of October I updated my install of Norton SystemWorks from NSW 2002 to
NSW 2003 as well as updating the nVidia drivers to the latest version (40.72). Things have not been the
same since. I started getting random system freezes and 0D or 0E Fata Exceptions as Windows 98SE
was starting to initialize and display the desktop and Windows signon. I was always able to restart in
Safe Mode, but not always able to get around the Fatal Exception in normal mode.
Over the course of the next month, the pc never really attained stability. Sometimes it ran fine for a while,
then would just freeze. I started backing up more often and got PowerQuest Drive Image for disaster
recovery purposes. I already had a tape drive, but sometimes the tape backup software would
freeze/stop functioning in the middle of a backup.
I then got a larger hard drive, so that I do Drive Image backups to HDD rather than CD-RW. I got an
ATA-100 80 Gb drive but did not yet install it.
This past week I checked your website to see if I could find any additional information about my BIOS
and if it would support the new hard drive. I saw that I was on v3.3 and that you have v3.5. It also
appeared to me that v3.5 was needed for the new drive. It also seemed to me that my issues could be
hardware (ie, system board) related.
Anyway, I used your v3.5 BIOS update utility to backup my existing BIOS. Double checked my system
board and chipset and then tried the v3.5 update. The flash update did not write completely (out of the
two full rows of white progress boxes around 6 of them were blue). I restored the original bios and
regained some function. However, I can no longer even get through the CMOS setup without the pc
freezing.
I have reseated all cards and the processor as well as trying only one memory chip at a time. Nothing
has changed the behavior. I even reflashed the v3.5 BIOS, this time with a clean update (all white
progress boxes). Still no stability.
I am just looking for some advice. It my system board gone? Was it going or did I destroy it with the bios
update? Since my original equipment manufacter is no longer in business I have nowhere to go for
hardware support. Is it possible to find a replacement system board or better to cut my losses and get a
new pc. I am fairly pc competent but not to the point where I would swap out a system board on my own.
Vic

On Friday I decided to take everything apart; including removing the system board and then put it all back together. Believe it or not, without any repairs since I last replied in this forum, my pc is now somewhat revived. It appears as though my problem might have been that the processor was not completely seated in the slot. Does that make sense? The freezing during CMOS setup or OS startup has completely disappeared.
There are still some stability problems and there also appears to be a BIOS issue.
I think the stability problems are from corrupt OS files (Win98 SE) and I am thinking the only recovery for that is to reinstall. Nothing like a perfect opportunity to move this hardware to Windows 2000.
Now for the BIOS question. This board is an MS-6199VA. The BIOS is W6199VMS v3.5 100200 with BIOS ID of 01/01/2000-692-596-W977-2A6LGM4BC-00. At the tail end of the BIOS startup I get the following..
CMOS Checksum error - Defaults loaded.
Warning! CPU has been changed.
Please re-enter CPU settings in the CMOS setup and remember to save before quit.
Press F1 to continue or DEL to enter CMOS setup
I have gone through all the CMOS setup options, set them, changed some; like disabling a serial port and setting up a power on password, and save them. Yet I still get this message every time.
Other than halting the startup until I press F1 or DEL there seems to be no other negatives. Am I missing something or is there a storm coming?
Vic

M305-S4848 Audio Muddy/lack of treble after system board replacement

I recently sent in my M305-S4848 for repair and the system board was replaced. (wouldn't charge while powered on)
After receiving my laptop back from repair I noticed that the sound quality of my speakers had gone downhill. There is no crackling/hissing and the like but there is a muddy, midrange filled tone and a reduction in treble and clarity. When this computer was serviced the BIOS was updated and the software was set back to factory spec.
     I have a second m305-S4848 that I purchased for my wife at the same time. Our computers sounded the same before mine was sent for repair and different now. I have spoken to Toshiba support, had a remote session performed by a high level tech. No one seems to have any idea what may be wrong. I was told to send in the computer again.
     The concern I have is that the sound is more mediocre than bad and if serviced by a tech without a good ear, the moderate audio problem will not be noticed/corrected/taken seriously. Any help would be greatly appreciated. I'm hoping someone might know what could have happened and the best way to communicate my problem to whatever service depot my notebook may be sent to.
BTW: Notebook seems to be running well in all other respects at this point.
                                             Thanks in advance
                                                            Jason

Chris,
I wanted to reply here on your original thread . I appreciate your noting your prior case 10140045 - this appears not to have been routed correctly and was closed out. We will escalate this situation and ensure follow up.
I appreciate your speaking up, and your patience. I really hope we can restore your confidence in Lenovo.
Mark
ThinkPads: S30, T43, X60t, X1, W700ds, IdeaPad Y710, IdeaCentre: A300, IdeaPad K1
Mark Hopkins
Program Manager, Lenovo Social Media (Services)
twitter @lenovoforums
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

"Product info programmed into the system board is missing or invalid system board:

Product info programmed into the system board is missing or invalid system board:
OOA product name,
OOA serial #,
OOA product #,
OOA system board ct#
I get this message every time I start up suddenly. What does it mean and how do I fix It? I just bought this laptop from Staples about 4 months ago!!!
This question was solved.
View Solution.

It is very important that you post the product name or product number of your notebook and the version of the installed BIOS here in your thread.
How to identify your notebook.
Remove the battery and look in the compartment where the battery was installed. You should see a printed part number and a product name. Please post one or both of them (with all alphanumeric characters here).
It also helps if you post the country of purchase
I will pass that information to an internal HP contact as soon as you post it to see if we can get that resolved for you.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

System board of SF 6900 is shutting down automatically of high temperature

Hi
In SF6900, the system board SB1 is automatically shutting down. The following are the logs, can anyone confirm if i have to replace the system board or is there any other fix?
showlogs -v
Sep 18 12:31:25 sep21-admin-sc0 Platform.SC: [ID 112625 local0.notice] FT1, fan speed, High (4,2)
Sep 18 12:31:25 sep21-admin-sc0 Platform.SC: [ID 120817 local0.notice] FT2, fan speed, High (4,2)
Sep 18 12:31:25 sep21-admin-sc0 Platform.SC: [ID 129009 local0.notice] FT3, fan speed, High (4,2)
Sep 18 12:31:25 sep21-admin-sc0 Platform.SC: [ID 861705 local0.notice] /N0/SB1, sensor status, outside acceptable limits (7,1,0x205010500030000)
Sep 18 12:31:25 sep21-admin-sc0 Platform.SC: [ID 101552 local0.notice] /N0/SB1, sensor status, shutdown (7,3,0x205010500030000)
Sep 18 12:31:49 sep21-admin-sc0 Platform.SC: [ID 811484 local0.notice] /N0/SB1: powered off
Sep 18 12:34:18 sep21-admin-sc0 Platform.SC: [ID 807377 local0.notice] FT0, fan speed, Low (4,1)
Sep 18 12:34:18 sep21-admin-sc0 Platform.SC: [ID 169540 local0.notice] FT1, fan speed, Low (4,1)
Sep 18 12:34:18 sep21-admin-sc0 Platform.SC: [ID 431684 local0.notice] FT2, fan speed, Low (4,1)
Sep 18 12:34:18 sep21-admin-sc0 Platform.SC: [ID 693828 local0.notice] FT3, fan speed, Low (4,1)
Sep 18 16:19:25 sep21-admin-sc0 Platform.SC: [ID 740317 local0.notice] Main, up 28 days 20:27:43, Memory 7,031,904
Sep 18 20:19:25 sep21-admin-sc0 Platform.SC: [ID 683143 local0.notice] Main, up 29 days 00:27:43, Memory 6,084,592
Sep 19 00:19:25 sep21-admin-sc0 Platform.SC: [ID 783229 local0.notice] Main, up 29 days 04:27:43, Memory 6,755,952
Sep 19 04:19:25 sep21-admin-sc0 Platform.SC: [ID 248112 local0.notice] Main, up 29 days 08:27:43, Memory 5,805,104
Sep 19 08:19:25 sep21-admin-sc0 Platform.SC: [ID 627151 local0.notice] Main, up 29 days 12:27:43, Memory 6,410,168
Sep 19 12:19:25 sep21-admin-sc0 Platform.SC: [ID 151055 local0.notice] Main, up 29 days 16:27:43, Memory 5,591,520
Sep 19 16:19:25 sep21-admin-sc0 Platform.SC: [ID 191622 local0.notice] Main, up 29 days 20:27:43, Memory 7,114,208
Sep 19 17:24:35 sep21-admin-sc0 Platform.SC: [ID 449265 local0.alert] FULL-COOLING ENGAGED: turning fans high
Sep 19 17:24:35 sep21-admin-sc0 Platform.SC: [ID 746364 local0.warning] WARNING: /N0/SB1 temperature is approaching max limit of 105C
Sep 19 17:24:35 sep21-admin-sc0 Platform.SC: [ID 332049 local0.warning] /N0/SB1 DX 0 Temp. 0 value: 107 Degrees C
Sep 19 17:24:35 sep21-admin-sc0 Platform.SC: [ID 362413 local0.warning] Check for abnormal environmental operating conditions.
Sep 19 17:24:35 sep21-admin-sc0 Platform.SC: [ID 310355 local0.error] Notice: Shutting down /N0/SB1 as temperature exceeds max limit of 105C
Sep 19 17:24:35 sep21-admin-sc0 Platform.SC: [ID 969886 local0.error] /N0/SB1 DX 0 Temp. 0 value: 107 Degrees C
Sep 19 17:24:35 sep21-admin-sc0 Platform.SC: [ID 231341 local0.error] Check for abnormal environmental operating conditions.
Sep 19 17:24:35 sep21-admin-sc0 Platform.SC: [ID 468401 local0.notice] /N0/SB1: has been queued for power off.
messages logs
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 783031 kern.info] NOTICE: [AFT0] L3_WDC Event detected by CPU519 at TL=0, errID 0x000472db.3855bbf0
Sep 4 09:44:17 sep21 AFSR 0x00000000.0000001c AFSR_EXT 0x00000002<L3_WDC> AFAR 0x00000020.1b7b4e00
Sep 4 09:44:17 sep21 Fault_PC 0x1023c8964 Esynd 0x001c /N0/SB1/P3/E0 J7400
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 654596 kern.info] [AFT0] errID 0x000472db.3855bbf0 Data Bit 11 was in error and corrected
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 171505 kern.info] [AFT2] errID 0x000472db.3855bbf0 E$tag PA=0x000000a1.7e7b4e00 does not match AFAR=0x00000020.1b7b4e00
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 351869 kern.info] [AFT2] errID 0x000472db.3855bbf0 PA=0x000000a1.7e7b4e00
Sep 4 09:44:17 sep21 E$tag 0x00000142.fc004581 E$state_0 Shared
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 895151 kern.info] [AFT2] E$Data (0x00) 0x00000000.00000000 0xf8800000.00000000 ECC 0x104
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 895151 kern.info] [AFT2] E$Data (0x10) 0x00000000.ffffffff 0x00000000.00000000 ECC 0x138
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 895151 kern.info] [AFT2] E$Data (0x20) 0x00000000.00000000 0x00000000.00000000 ECC 0x000
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 895151 kern.info] [AFT2] E$Data (0x30) 0x00000000.00000000 0x00000000.00000000 ECC 0x000
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 171505 kern.info] [AFT2] errID 0x000472db.3855bbf0 E$tag PA=0x00000023.f47b4e00 does not match AFAR=0x00000020.1b7b4e00
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 351869 kern.info] [AFT2] errID 0x000472db.3855bbf0 PA=0x00000023.f47b4e00
Sep 4 09:44:17 sep21 E$tag 0x00000047.e8004584 E$state_0 Modified
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 895151 kern.info] [AFT2] E$Data (0x00) 0x00000000.00000000 0x00000000.00000005 ECC 0x05c
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 895151 kern.info] [AFT2] E$Data (0x10) 0x00000000.0151fcb0 0x0000000b.00000000 ECC 0x179
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 895151 kern.info] [AFT2] E$Data (0x20) 0x00000000.00000210 0x00000023.2586d7e0 ECC 0x072
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 895151 kern.info] [AFT2] E$Data (0x30) 0x00000000.0104a8bc 0x00000000.00000000 ECC 0x08d
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 171505 kern.info] [AFT2] errID 0x000472db.3855bbf0 E$tag PA=0x00000005.62fb4e00 does not match AFAR=0x00000020.1b7b4e00
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 351869 kern.info] [AFT2] errID 0x000472db.3855bbf0 PA=0x00000005.62fb4e00
Sep 4 09:44:17 sep21 E$tag 0x0000000a.c5004581 E$state_0 Shared
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 895151 kern.info] [AFT2] E$Data (0x00) 0x00000000.00000000 0x00000000.00000000 ECC 0x000
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 895151 kern.info] [AFT2] E$Data (0x10) 0x00000000.00000000 0x00000000.00000000 ECC 0x000
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 895151 kern.info] [AFT2] E$Data (0x20) 0x00000000.00000000 0x00000000.00000000 ECC 0x000
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 895151 kern.info] [AFT2] E$Data (0x30) 0x00000000.00000000 0x00000000.00000000 ECC 0x000
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 171505 kern.info] [AFT2] errID 0x000472db.3855bbf0 E$tag PA=0x00000023.a57b4e00 does not match AFAR=0x00000020.1b7b4e00
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 351869 kern.info] [AFT2] errID 0x000472db.3855bbf0 PA=0x00000023.a57b4e00
Sep 4 09:44:17 sep21 E$tag 0x00000047.4a004581 E$state_0 Shared
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 895151 kern.info] [AFT2] E$Data (0x00) 0x00000000.00000000 0x00000000.00000000 ECC 0x000
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 895151 kern.info] [AFT2] E$Data (0x10) 0x00000000.00000000 0x00000004.d57b4e18 ECC 0x183
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 895151 kern.info] [AFT2] E$Data (0x20) 0x00000004.d57b4e18 0x00000000.00000000 ECC 0x140
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 895151 kern.info] [AFT2] E$Data (0x30) 0x00000000.00000000 0x00000004.d57b4e38 ECC 0x10c
Sep 4 09:44:17 sep21 SUNW,UltraSPARC-IV+: [ID 809480 kern.info] [AFT2] errID 0x000472db.3855bbf0 L2$tag PA=0x00000043.670b4e00 does not match AFAR=0x00000020.1b7b4e00

continuation...
showchs -b
Component Status
RP0 Suspect
RP1 Suspect
RP2 Suspect
RP3 Suspect
testboard SB1
{N0/SB1/P2/C0} set_panther_rd_bypass_wr: cpuno 6 ctl_addr 00000000.00000030 val 37064778
.0c060301
{N0/SB1/P3/C0} set_panther_rd_bypass_wr: cpuno 7 ctl_addr 00000000.00000030 val 37064778
.0c060301
{N0/SB1/P0/C0} set_panther_rd_bypass_wr: cpuno 4 ctl_addr 00000000.00000030 val 37064778
.0c060301
{N0/SB1/P2/C0} Subtest: Memory DIMMs Init
{N0/SB1/P1/C0} set_panther_rd_bypass_wr: cpuno 5 ctl_addr 00000000.00000030 val 37064778
.0c060301
I have only posted selected part of testboard sb1. Please help me in getting into a conclusion
Edited by: ytamourt on Sep 21, 2010 4:52 AM

6555b System Board

Similar Messages

Maybe you are looking for