6600 access point - pain / help me

I've just got me hands on a 6600 and it keeps asking me to select an access point (ie: GPRS or my provider) if I say yes it dials up the number - if I say no (cancel) it go's away for about a minute then "pops" back up - can anbody tell me how to STOP it poping back up!!! its driving me round the bend
ps - I have looked in the providers manual (not a Nokia manual) and its no help.
Thanks

Does this help: http://discussions.nokia.co.uk/discussions/board/message?board.id=messaging&message.id=89&query.id=0...

Similar Messages

  • WAP2000 Wireless-G Access Point (Setup Help)

    Hi,
    We have a wireless-g access point typically (and previously, in this case) used for a small business. We were given the device for free and wanted to reset the device to use as our wireless router at home. First and foremost, can a wireless access point double as a home wireless router? I was told that only one computer/laptop at a time can connect to a wireless access point, unlike a wireless router which allows multiple devices to connect to a wireless home network at a time? Is this true?
    Second, because the device is not new, we no longer have the setup instructions. Upon resetting the device (holding down the reset button for 10 or more seconds), we were unable to access the WAP2000 online setup page for a username and password. The device is being picked up by our macbooks and shows up in the Airport as "linksys-g." However, we are unable to access the setup page or communicate with the access point. We have tried typing http://198.162.1.1/ in our address bar, but have had no luck.
    Do you have any suggestions as to how to set up the device? Also, can this device double as a router that will allow multiple laptops and devices (i.e. sony playstation) to access and use the wireless network simultaneously.
    Thank you for your help.

    Sam,
    First yes you won't to factory reset the unit. You should hold down the reset button longer than 30 seconds and no longer than 45.Once this is back to factory default, the current ip address should be 192.168.1.245 , you will need to statically assign your pc an address in 192.168.1.1 /24 range and make sure you are plugged directly into WAP2000. Now you should be able to access the AP. Default username = admin password = admin
    http://www.cisco.com/en/US/docs/wireless/access_point/csbap/wap2000/quick_start/guide/WAP2000_Quick_Start_Guide.pdf
    Above is a quick start guide for reference.
    Now just configure accordingly.
    Thanks,
    Jasbryan    
    Cisco Support Engineer
    .:|:.:|:.

  • Just Moved, Want to Use My e3000 as just an access point NEED HELP

    Hey, I just moved into a house the other day, the router/modem is upstairs, my desktop/xbox only has wired capabilities, and my laptop has wifi. I was trying to just make a bridge with my my laptop to my desktop while i try and figure out how to get all my stuff working again, but found out the jack in my laptop is broken, so it only has WIFI.
    My question is, am I able to use my e3000 to connect to their wifi signal via wifi, in which i can just run a cable to my xbox and desktop within the room?
    I cant run 2 cable from upstairs to downstairs for my desktop/xbox, so was hoping this was possible. thanks

    Yes, and you can turn wi-fi access on after enabling airplane mode if you want or need internet access via an available wi-fi network.

  • CISCO Aironet access point - not able to connect by user.

    Hi,
    I have CISCO Aironet access point C1130 in my network , but not able to connect by users, I can see below logs from access point. please help on this.
    Jun 13 17:50:10.686: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000         
    Jun 13 17:50:10.686: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247         
    Jun 13 17:50:15.678: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000         
    Jun 13 17:50:15.678: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247         
    Jun 13 17:50:20.544: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000         
    Jun 13 17:50:20.544: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247         
    Jun 13 17:50:24.832: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000         
    Jun 13 17:50:24.832: RADIUS: Retransmit to (20.33.100.11:1645,1646) for id 1645/247         
    Jun 13 17:50:29.741: RADIUS: no sg in radius-timers: ctx 0x10653F8 sg 0x0000         
    Jun 13 17:50:29.741: RADIUS: Fail-over denied to  (20.33.100.11:1645,1646) for id 1645/247         
    Jun 13 17:50:29.741: RADIUS: No response from (20.33.100.11:1645,1646) for id 1645/247         
    Jun 13 17:50:29.741: RADIUS/DECODE: No response from radius-server; parse response; FAIL         
    Jun 13 17:50:29.741: RADIUS/DECODE: Case error(no response/ bad packet/ op decode);parse response; FAIL         
    Jun 13 17:50:29.741: dot11_auth_dot1x_parse_aaa_resp: Received server response: FAILOVER_RETRY         
    Jun 13 17:50:29.742: dot11_auth_dot1x_parse_aaa_resp: found eap pak in server response         
    Jun 13 17:50:29.742: Client 5864.6c67.3718 failed: EAP reason 0         
    Jun 13 17:50:29.742: dot11_auth_dot1x_parse_aaa_resp: Failed client 5894.6b37.3518 with aaa_req_status_detail 0         
    Jun 13 17:50:29.742: dot11_auth_dot1x_run_rfsm: Executing Action(SERVER_WAIT,SERVER_FAIL) for 5894.6b37.3518         
    Jun 13 17:50:29.742: dot11_auth_dot1x_send_response_to_client: Forwarding server message to client 5894.6b37.3518         
    Jun 13 17:50:29.742: dot11_auth_dot1x_send_response_to_client: Started timer client_timeout 30 seconds         
    Jun 13 17:50:29.743: dot11_auth_dot1x_send_client_fail: Authentication failed for 5894.6b37.3518         
    Jun 13 17:50:29.743: %DOT11-7-AUTH_FAILED: Station 5894.6b37.3518 Authentication failed
    Regards,       

    Hi Niham,
    You can try few things to troubleshoot this -
    1. check the reachability of Radius server from your wlc (ping).
    2. verify the IP address of Raduis server configured on wlc.
    3. wlc in the Radius server ?
    4. Shared Secret must be same on wlc and in raduis server.
    Plz do not forget to rate useful post.
    Thanks

  • Linksys Wireless-B Router & Access Point question

    Ok, I have a Linksys wireless B router (cant remember the model name off of the top of my head) and it connected to a desktop that I have.  I just purchased a Buffalo Wireless-G MIMO router which has the ability to act as an access point.  I was wondering if I set the Wireless-B router up to my desktop where my modem is, and then turn on the Access Point feature with my Buffalo router, would the two brands work together or no?  Also, if they did work and the Buffalo router acted as an access point would I be able to connect my PS3 via one of the ethernet port on the back of the Buffalo access point?  Help would be greatly appreciated, thanks.
    I just purchased this Buffalo router after returning the Linksys Wireless-G with SpeedBooster and having numerous problems with my Verizon DSL (Westell 6100 modem).

    Yes you can.  Here is a LINK to use as a reference.  The only thing you will run into is the routers IP's may be different so make sure they are in the same range.  Example router 1:192.168.1.1  and router 2:192.168.1.2 but it may vary depending on what you want your private IP range to be. 
    The router you want to set as a AP make sure it has the latest firmware and has the SSID/security all set up.  Make sure the IP for the router is set then disable the DHCP.  Then connect router 1 via numbered port to the number 1 port of the second router.
    Message Edited by Ikester on 07-16-2007 09:43 AM
    Richard Aichner (Ikester)

  • MSI AP11b wireless IEEE802.11b Access Point

    hi to all msi admin there and members.
    im new here in this forum can anyone help me to answer my question about MSI AP11b wireless IEEE802.11b Access Point product.
    I'm planning to buy MSI AP11b wireless IEEE802.11b Access Point to  use my new laptop with wireless and enable me to share my internet using ap11b accesspoint..My problem is im using an usb adsl modem with (no Rj45 jack)only USB. so i can only connect my adsl modem to my desktop pc and i want to share my internet to my laptop using the wireless connection,but the problem is i dont know if this MSI AP11b wireless IEEE802.11b Access Point can help me to share my internet connection over my laptop. i have an idea and i dont think if this would work ex. if i buy MSI AP11b wireless IEEE802.11b Access Point and right after then, as usual my desktop pc is currently connected in the internet using my usb adsl modem, i want to use my desktop pc as a server using internet connection sharing(ICS) (im using WinXP) i have ethernet card that is built on my board and which ap11b available is RJ45 JACK im gonna plug my rj45 and connect it to rj45 jack of ap11b.
    is this possible that im going to use my desktop pc to become serve because my adsl modem(USB)(no rj45)r and share my internet using ap11b wireless accesspoint on my wireless laptop?
    anyone i need some good advice in this cases...
     

    yes, you could use ap11b to become server and share internet for your wireless laptop.
    You have to connect the ap11b to your desktop PC ethernet card via RJ45.
    If the ASP can give you more than 2 IP, you can choose "Bridge model" in the "Network Connections" setup.
    If the ASP only give you 1 IP, you should share the Internet Connection.
    Network connections-->Local Area Connection-->right click-properties-->Advanced-->click "Allow other network users to connect through this computer's Internet connection"

  • Help with using the WRT54G as an Access Point

    Ever since I've been using the WRT54G as an access point behind another router I have been experiencing intermittent disconnects and reconnects from the internet anywhere from once every 5 to 60 minutes.  I get the message notifcation that the Local Area Network is disconnected for a split second before everything reconnects and works fine.  This has been happening on my desktop which is wired directly to the WRT54G which itself is wired directly to the other router, but I have also experienced these disconnects with my iPhone and laptops which have been using the wireless signal. 
    When I was connected directly to the original router I hadn't experienced any of these problems.  I've also tried changing settings and even disabling the wireless broadcast of the WRT54G but to no avail.  I can't figure out what the issue is, but it seems to also be affecting the wireless broadcast of the original router. 
    I've updated firmware for the Linksys, and I've done a reset for the Linksys as well.
    Any help would be much appreciated to get rid of these disconnects.

    OK, so I've tried a different setting to see if it'll work. 
    Previously I had not configured the WAN of the Linksys router at all and left it on Auto (DHCP) even though I disabled the DHCP for the LAN.  I've now set the WAN up to a random Static IP and hopefully this will solve the problem, but I'm not sure as of yet, if anyone could look over the settings to see if they're correct please let me know.
    Router 1- (Router)
    WAN - Configured to ISP
    LAN - DHCP
    IP: 192.168.1.1
    Subnet: 255.255.255.0
    IP Range: 192.168.1.100 - 192.168.1.150
    Router 2 - Linksys (AP)
    WAN - Static IP
    IP: 64.XXX.XXX.1 (made up value)
    Subnet: 255.255.255.0
    Gateway: 64.XXX.XXX.254 (made up value)
    DNS: XX.XXX.XXX.X (made up value)
    LAN - DHCP disabled
    IP: 192.168.1.2
    Subnet: 255.255.255.252
    The WRT54G was a bit of a pain in terms of what Static IP and Gateway values they would accept, so I had to randomly put in values until I found something that worked.  So far no disconnects, but it's only been half an hour.  I can't seem to access the admin page for my Linksys router at 192.168.1.2 anymore though.

  • Help with N97 and Access points after V20 upgrade

    Hi Guys,
    I'm hoping someone can help me - I have an 505 uk unit and have changed to a generic euro product code to get the V20 software ( as theres a 2 week wait minimum for the network to release its custome version ) and its working brilliantly - except - in connections all my accesspoints have gone - I now show 13 uncategorised access points which I cant expand or open and it wont let me delete the lot as it says its protected Anyone able to sort this out and tell me what to do so I can get back to Internet and Contract WAP etc... destinations?
    Much Appreciating any help.
    Alex

    Hi Alex,
    I am not sure what kind of applications are preloaded in your location.  I suppose the problem you faced is unable to delete certain definitions under the Destinations setting?
    If a hard reset is not an option (not for me as I have purchased apps from the OVI store), I would create a dummy Destination to house all these unwanted definitions.  That way, so long as the default connection does not utilize this dummy Destination, I think you are OK.  Hope this helps.
    Visit http://www.WilfridWong.com - where all good things are meant to be shared!

  • N97 OTA access point help

    hi all, got a probem here that seems to been doin my head in over the last few days. basically i bought a brand new locked to tmobile N97, im a virgin customer.. now, i'm wanting to do a firmware upgrade.. due to having an old **bleep** laptop that only has 248mb of ram i cant d the upgrade via nokia pc suite so my only other option is OTA.. right, so, i dial *#0000# then go to options, then check for updates... up pops a message saying a need to define an access point, ok.. not understanding it much i try and manually add some stuff myself, to no avail... then i do some forum posting and manage to get these settings: Server Name Nokia Server ID Nokia Server password firmupservpass Access point [select your preferred AP] Host address https://dms.update.nokia.com/dms/omadm Port 443 User name nokiams DM password nokiamspass Allow configuration Yes Auto accept all requests Yes but... that hasnt solved my problem, when entered and i try to connect to do the upgrade i get a connection error. my only option is this forum, its a nokia fone and a nokia forum i cant get my head round it as i can use the internet n my fone brilliantly, surely the internet and the OTA access point are the same thing?

    To add an access point select settings-connectivity-destinations-Access point , Automatically search for available access points ?, select yes and choose access point. Then go into Internet and set the priorities to WLAN number 1 T-Mobile number 2 etc
    Good Luck
    PS Nokia Software Updater should still work on computer, even with low memory or weak internet , just a bit slower.
    If I have helped at all, a click on the White Star is always appreciated :
    you can also help others by marking 'accept as solution' 

  • Help me find the required Wireless Access point

    Dear Friends,
    I am in search of a access point with below specification, so please let me know that which model has this functionalities.
    . Wireless Access Point:
    * No of port should be 10Base-T/100Base-TX Ethernet
    * Standard should be IEEE 802.11g, IEEE802.11b, IEEE 802.3, IEEE 802.3u, IEEE 802.3af(PoE), 802.1q(VLAN) , 802.1X(Security authentication), 802.11i ready (Security WPA2), 802.11e ready (wireless QoS), 802.11F(Wireless roaming)
    * LEDs should be power, PoE, Wireless, Ethernet
    * Web Management should be built-in web user interface for easy browser-based configuration (HTTP/HTTPS)
    * SNMP Support should be SNMP version 1, 2c, 3
    * Operation modes should be access point made, point to point bridge mode, point to point multipoint bridge mode, repeater mode
    * External antennas should be 2 (omni directional) SMA detachable
    * Security should be WEP 64-bit/128-bit, WPA-PSK, WPA2-PSK, WPA-ENT, WPA2-ENT
    * Access Control should be wireless connection control: MAC-based
    * Wireless Security monitor should be Intrusion alarms(e.g. rogue client detected, spoofed MAC address) Denial-of-service alarms (e.g. duration attack, association table full) vulnerability alarms (e.g. access point is not using encryption, access point is broadcasting SSID)
    * Power should be 12V 1A DC input, and IEEE 802.3af compliant PoE. Maximum power draw should be 3.36W

    Hello Shekib,
    All you did was describe the WAP200.
    It fully fits in your description.
    Please check it and see with your eyes.
    http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps10047/ps10048/data_sheet_c78-501966.html
    I hope i helped you.
    Regards.
    Andrey Cassemiro.

  • Having Issues with E1000 as an Access Point setup - Please Help

    Quick background - Using an E2000 as my main router for a DSL connection (using an ISP provided Zyxel 660HW modem with wireless disabled if that matters). I have an E1000 that I want to setup as a LAN to LAN connection to the E2000 at the far end of the house and two floors down to extend my network.
    I am pretty network saavy and thought this would be a snap. But I am running into trouble and hoping someone can assist.
    Here are the steps I took:
    1. I ran a CAT 5 connection down to the basement where the E1000 is to be setup.
    2. I hard reset the E1000 to factory defaults
    3. I connected my notebook to the E1000 via a LAN port. At this stage the E1000 is NOT on the network
    4. I configured the E1000 with an IP of 192.168.1.2 - my main router (E2000) is set to 192.168.1.1 and the IP ranges start at .100 so this should present no conflicts
    5. I disabled DHCP
    6. I disabled NAT
    7. I saved settings and rebooted router
    8. I removed connection to notebook and plugged in the CAT 5 run from the E2000 - LAN port 1 on both (no WAN/Internet port used)
    At this stage I expected the E1000 to act as an Access Point but it is not functioning properly. The first thing I notice is that the E1000 that should now be the AP is broadcasting the router name (something like Cisco 54653) even though this is not a broadcast SSID but only the router name. That is odd, I believe.
    I have tried rebooting both the E2000 and E1000 along with the modem, no luck. I have tried different IPs for the E1000 just in case but again no luck, the wireless is not extended.
    Any advice or guidance? Am I doing something wrong?
    Any help is appreciated.
    Solved!
    Go to Solution.

    It sounds like you have configured the E1000 properly, but you didn't describe how you have configured the Zyxel and E2000.
    Do you have A or B ?
    A.  Zyxel set to full bridge mode.  Then connect Zyxel to E2000's internet port and configure E2000 for PPPoE internet connection type (and DHCP server enabled and NAT enabled). Change MTU to manual on E2000 and enter 1492.  And then connect your E1000 as you described.  Internet connection type on E1000 is AutoconfigDHCP.
    B. Zyxel is configured as modem/router (DHCP server enabled and NAT enabled).  Then connect Zyxel to E2000's internet port.  E2000 is configured as router (DHCP server is enabled and NAT is enabled) and local IP address is 192.168.2.1.  Internet connection type on E2000 would be AutoconfigDHCP.  E1000 is configured as you described except local ip address is 192.168.2.2.  Internet connection type on E1000 is AutoconfigDHCP.
    http://support.earthlink.net/articles/dsl/zyxel-p660rd1-how-to-set-the-modem-for-bridge-mode.php

  • Help needed setting up access point to public network

    Hi from a newbie,
    Assuming they are suitable, I want to use one (or two) AP1232AG-E-K9 access points for Internet connection through a public wireless network (BTFON), where wire broadband is not an option. I've downloaded what I think is the correct manual for the APs and I'm now scratching my head as to where and how to start setting them up. I want to use these Cisco APs in the hope they will give me better wireless performance than I'm currently getting, which is frequently flakey.
    I've tried to reset the APs to the factory default but there seem to be different ways of doing this depending on what you want and what you've got. I made up a console cable  to access the console but there even appear to be different versions of  this so I'm not sure if the cable I have is the correct one.
    I have setup and used lower end wireless devices in the past but these Cisco units seem real complicated and I'm going to need help in getting them working.
    Any assistance would be much appreciated.
    Kind regards,
    Glenn.

    Updated network diagram.

  • AP Extreme (WiFi Access Point)... LAN... Web Proxy Server help.

    Hello...
    I need a little help configuring this Airport Extreme as a Wireless Access point, serving a bunch of iPads via the schools LAN connection for which traffic is routed through a Web Proxy Server. I've been told to set it up as a bridge as the PC LAN and Proxy are providing NAT but can't seem to crack it.
    The WiFi side of things is up and running, we can all see and connect to the AP.
    I'm told that it was working fine before the school break in the summer, then something was changed and the position of the AP altered.
    The Web Proxy Server is normally accesses from the PC's via the following address... IP > 10.12.14.122  //  PORT > 3128
    I'm not certain where the Proxy settings need to go in the new 'simple' Airport Utility, can't see a place for Port at all?!?
    (I've taken the AP home, tried it on my home network and it works fine, so we know its all OK and its down to config).
    Here are some screen images of the settings as they are, that do not work.
    (I was trying a few different settings hence the screens like Static/DHCP etc.)
    Any help is greatly appreciated.

    Hi Daniel,
    >>Now when I go on a client site my internet access on the host laptop is via a web proxy on a LAN connection.
    "LAN connection" means physical NIC (Realtek PCIe GBE Family Controller) ?
    " web proxy " means adding a proxy server IP in IE ?
    Bounding the NIC (Realtek PCIe ) to external virtual switch then connect all VMs to that external virtual switch ,still can not access ?
    Best Regards
    Elton Ji
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • Configuring Cisco Aironet 1100 Access Point. Please help!

    Hi all,
    I have dozens of Cisco Aironet 1100 access points, each is managing its own wi-fi with DHCP.
    I had to disable dhcp on them because they are on a wired subnet where I am using the static IPs and don't want my wired clients to get DHCP addresses, nor someone to be able to plug the wire into own laptop and get on the network.
    It's been working fine with one exception - I need to be able to ping my access points from the central site, and I can't.
    What IOS command would enable ICMP echo on my access points in this case?
    Please help!

    Hi all,
    I have dozens of Cisco Aironet 1100 access points, each is managing its own wi-fi with DHCP.
    I had to disable dhcp on them because they are on a wired subnet where I am using the static IPs and don't want my wired clients to get DHCP addresses, nor someone to be able to plug the wire into own laptop and get on the network.
    It's been working fine with one exception - I need to be able to ping my access points from the central site, and I can't.
    What IOS command would enable ICMP echo on my access points in this case?
    Please help!

  • Access point problem... help

    i have an access point which is not suppose to be in the native vlan, the port which is connected to the access point has no trunk.
    when i checked the native vlan, this error prompted...
    %SYS-4-P2_WARN: 1/Tag 1 on packet from <mac add> port 1/3, but port's native vlan is 2
    but when i unchecked it, the connection lost between AP & switch...
    what actually happened? can anyone plz help me?

    Hi,
    the connected switch a Cisco Switch? If yes do you have configured a "switchport access vlan xx"?
    If the connected Switch is not a Cisco i had a problem similiar to yours and fixed it with the setup of the used VLAN (in my case VLAN 10) as Native VLAN in the AP.
    Maybe you should setup the Native VLAN to 2 in your AP Config.
    I Hope that helps.
    Best regards,
    Frank

Maybe you are looking for