6600 Fold - Too Much Power

I have the 6600 Fold, and recently when using the USB connecting cable, I get the following message displayed " Connected device uses too much power. Disconnect cable".
The USB cable is connected from the mobile phone to a Asus notebook. As mentioned, this has only just begun to occur in the last few weeks. I now can only use the 240 volt charger to recharge the phone.
Any suggestions to what is causing the problem or has anyone else experienced the same.

The USB port on the camera connection kit is only for importing photos/videos from a camera, SD card or a USB flash drive. It can't be used for export of any file type.
 Cheers, Tom

Similar Messages

I tried to export photos from iMac to iPad using a USB flash drive. The photos are on the drive but when I plug it into the iPad, the iPad says the device requires too much power. Any ideas of what type of USB flash drive I should use?

I tried to export photos from iMac to iPad using a USB flash drive. The photos are on the drive but when I plug it into the iPad, the iPad says the device requires too much power. Any ideas of what type of USB flash drive I should use?

You can transfer photos outside of iTunes. I do it all the time. THat said, i have a 50/50 success rate with them. I'd avoid sandisk and kingston, their bundled software triggers the 'too much power' warning.
I've had mixed luck with lexar, some work, some don't.
I did have good luck with an older 4 gig geek squad one.
Look for drives without software on them, without bright LED lights and I haven't gotten any larger than 4 gig to work, but that may just be me.
For a less troublesome way? h onestly, I use a SD card that I've formatted with the DCIM folder. I've never had one of them trigger the 'too much power' warning. Just make sure they're not SDXC. those don't work.

External HD claims to be drawing too much power, after 2 months of working

I have a 2.5" external HD enclosure from Mad Dog Multimedia that uses two USB connections, one for data and one for power. It's been working fine with my new Macbook Pro since I bought it several months ago, and continues to work fine with other comptuers. Last night I got a message that it was drawing too much power and the ports would be shut off. I unplugged and replugged it, and it continued to work all evening. This morning however, no matter what I do, it continues to tell me that its drawing too much power. This is baffling to me, because it has worked for the last few months, and still works on other computers, leading me to believe that something is wrong with my USB ports. Unfortunately I don't have much in the way of other USB devices I can use to test this hypothesis. Has anyone else encountered similar problems, and have you been able to resolve them successfully?

In the event you haven't done this already, shut down the computer and remove the external drive. Wait at least one or two minutes. Restart the computer then reconnect the external drive. See if your problem is resolved.
Try repairing the hard drive and permissions:
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger and Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation complete. I also suggest you run Repair Disk on the external drive as well while you still have DU running. Now quit DU and return to the installer. Restart normally.
If DU reports errors it cannot fix, then you will need Disk Warrior (4.0 for Tiger, and 4.1 for Leopard) and/or TechTool Pro (4.6.1 for Leopard) to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
If the above does not work, it is possible there's a problem with your OS X installation. It's difficult to know what that may be so you will need to experiment. First, restart the computer in safe mode. If this doesn't result in the problem ceasing, then try creating a new user account. Log out of your account and log into the new one. If this doesn't result in the problem going away, then more extreme measures are needed: reinstalling OS X. You might give this a try:
How to Perform an Archive and Install
An Archive and Install will NOT erase your hard drive, but you must have sufficient free space for a second OS X installation which could be from 3-9 GBs depending upon the version of OS X and selected installation options. The free space requirement is over and above normal free space requirements which should be at least 6-10 GBs. Read all the linked references carefully before proceeding.
1. Be sure to use Disk Utility first to repair the disk before performing the Archive and Install.
Repairing the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported, then quit DU and return to the installer.
2. Do not proceed with an Archive and Install if DU reports errors it cannot fix. In that case use Disk Warrior and/or TechTool Pro to repair the hard drive. If neither can repair the drive, then you will have to erase the drive and reinstall from scratch.
3. Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When you reach the screen to select a destination drive click once on the destination drive then click on the Option button. Select the Archive and Install option. You have an option to preserve users and network preferences. Only select this option if you are sure you have no corrupted files in your user accounts. Otherwise leave this option unchecked. Click on the OK button and continue with the OS X Installation.
4. Upon completion of the Archive and Install you will have a Previous System Folder in the root directory. You should retain the PSF until you are sure you do not need to manually transfer any items from the PSF to your newly installed system.
5. After moving any items you want to keep from the PSF you should delete it. You can back it up if you prefer, but you must delete it from the hard drive.
6. You can now download a Combo Updater directly from Apple's download site to update your new system to the desired version as well as install any security or other updates. You can also do this using Software Update.

HT4101 my camera says check connected device. USB device uses too much power. I have got the photos on before with persistence but this is not working

help

Is the USB drive you are trying to connect a USB thumb drive or a USB hard drive?
I have 4 USB thumb drives - an old one at 250MB, newer ones at 1GB and 4GB, and a new one at 8GB. All work in the camera connection kit except the 250MB (requires too much power). Suggest you get a new USB drive.
Use your camera's SD card.
Another way. You can use a USB flash drive & the camera connection kit.
Plug the USB flash drive into your computer & create a new folder titled DCIM. Then put your movie/photo files into the folder. The files must have a filename with exactly 8 characters long (no spaces) plus the file extension (i.e., my-movie.mov; DSCN0164.jpg).
Now plug the flash drive into the iPad using the camera connection kit. Open the Photos app, the movie/photo files should appear & you can import. (You can not export using the camera connection kit.)
Secrets of the iPad Camera Connection Kit
http://howto.cnet.com/8301-11310_39-57401068-285/secrets-of-the-ipad-camera-conn ection-kit/
 Cheers, Tom

I just got an iPad 2 16 gb and was wondering how I can upload pictures from a micro sd card but my iPad is saying cannot connect device using too much power. I have tried a 16 gb micro sd card and 4 gb micro sd card. Can anyone help please??

I got an iPad 2 and I cannot get my pictures to upload from a micro sd card as the iPad is saying device not accepted using too much power. Can anyone help? My iPad 2 is a 16 gb and my micro sd card is 4 gb

You can use a USB flash drive & the camera connection kit. First download the pics to your computer.
Plug the USB flash drive into your computer & create a new folder titled DCIM. Then put your movie/photo files into the folder. The files must have a filename with exactly 8 characters long (no spaces) plus the file extension (i.e., my-movie.mov).
Now plug the flash drive into the iPad using the camera connection kit. Open the Photos app, the movie/photo files should appear & you can import.
 Cheers, Tom

I want to download pictures from a Sony Memory Stick Pro Duo to my iPad 4. There is no cord for the camera and the USB dongle requires too much power through the camera connector kit. Any good solutions?

I want to download pictures to my iPad 4 from a memory stick pro duo. There are no cord connections for the camera and the USB dongle requires too much power through the camera connection kit. Any good solutions?

Another way. You can use a USB flash drive & the camera connection kit.
Plug the USB flash drive (works the same with an SD card) into your computer & create a new folder titled DCIM. Then put your movie/photo files into the folder. The files must have a filename with exactly 8 characters long (no spaces) plus the file extension (i.e., my-movie.mov; DSCN0164.jpg).
Now plug the flash drive into the iPad using the camera connection kit. Open the Photos app, the movie/photo files should appear & you can import. (You can not export using the camera connection kit.)
 Cheers, Tom

HT4101 It says it requires too much power when i connect my usb??

It says it requires too much power when i connect my usb??

Ok. Many USB's trigger the too much power warning. If you have a memory card, try doing it that way. Or you can experiment with other USB sticks. I've literally had a 50/50 success rate with the ones I've tried. You can try another one. Off brands seem to work better, along with smaller ones. The largest I've had work was a 4 gig. Kingston and Sandisk often trigger the too much power warning.
Do you know the naming format to make it work? Have a folder named DCIM in the upper level and make sure that all the photos have a name of exactly 8 characters.

Error message (Because a USB device was drawing too much power)

Hi Everyone,
Bought recently a new macbook pro 13 inch with Retina display with 120 GB flash drive.
Connected a non-apple CD drive to my macbook and after that started receiving this message: "Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled."
initially I was receiving this message after I switch on my macbook but now after every 30 seconds this message pops up although I never connected anything to my macbook through its USB ports.
Will highly appreciate for your help on how to get rid of this problem.
Regards
Homayun

Try resetting the SMC
Shut down the computer.
Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
Release all the keys and the power button at the same time.
Press the power button to turn on the computer.
Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.

I am trying to upload photos from my digital camera. Every time I try to plug it into my USB, the following error message comes up: "Because a usb device was drawing too much power from your computer, one or more of your USB devices have been disabled."

I am trying to upload photos from my digital camera. Every time I try to plug it into my USB, the following error message comes up: "Because a usb device was drawing too much power from your computer, one or more of your USB devices have been disabled."
I don't have anything else plugged into my MBP, so I am confused as to what's going on. This problem has never happened before. MBP is less than a year old - about 9 months old. HELP

Get a powered USB hub.
https://discussions.apple.com/community/notebooks/macbook_pro?view=documents

HT4106 How do I use a midi keyboard on GarageBand with my iPad? When I try it says the device cannot be used as it requires too much power. However, I have given the midi it's own power source.

How do I use a midi keyboard as an input device on garageband? Its an oxygen 61 board. I'm using an iPad camera connection kit and a separate power source for the midi but each time it says it cannot use the midi as it requires too much power.

I have the same problem with my iPad and 61. Sometimes it says device not supported and sometimes it rants about power - any solutions anyone ?

MacBook pro 13" mid 2010 "USB drawing too much power" HELP

Hi, my MacBook Pro keeps coming up with a window about 30 after start up saying "USB drawing too much power" and none if the USB ports work neither does the iSight camera (green light is constantly on) and the headphone jack won't work! I have tried re installing OSX but it hasn't worked! Apart from an SMC reset and a PRAM what else can I try? Absolutely nothing is plugged in not a single cable or keyboard or mouse just my MacBook on its own, is it definitely a software problem or am I going to have to get apple to repair the hardware because I do not have that much money to replace a logic board and get apple to replace it themselves. Thanks in advance!

I hope it works for you ...

To upload photos from my pc onto my ipad using a usb stick. I bought a camera connector kit and tried placing the usb stick onto one of the white square adaptors, stuck it into the ipad2 and I got 'the device uses too much power'' message. Pls help.

I am not very familiar with the ipad2. I wished to transfer some photos from my pc (not an apple pc but that is the only one I have) to my ipad2 as I thought it would be easier to cull them, edit, crop etc to create albums for our recent trip (the photos are already on the pc and no longer on the camera memory card). When I place the usb stick on the adaptor and stick it onto the Ipad2 I keep getting 'device uses too much power/ requires too much power' message. I read somewhere on the internet that a usb hub could be used to solve the issue but that did not work either. What am I doing wrong? Is there actually a way around this problem. If not why does apple sell this product for Ipad users at all?
Thank you for any help/ solution you can offer.
Regards

I'd ask that on the iPad forum.
https://discussions.apple.com/community/ipad

Can't print to HP Photosmart C5180. getting error mssg that says, "Because a USB device was drawing too much power from your computer, one or more of our USB devices have been disabled." Never seen this before. How do i fix this?

can't print to HP Photosmart C5180. getting error mssg that says, "Because a USB device was drawing too much power from your computer, one or more of our USB devices have been disabled." Never seen this before. How do i fix this?

Get a powered USB hub.
https://discussions.apple.com/community/notebooks/macbook_pro?view=documents

On my MacBook Pro with Retina Display, Why does the "USB Devices Disabled Unplug the device using too much power to re-enable USB devices" keep coming up after I unplugged the usb device?

On my MacBook Pro with Retina Display 15", that I purchased a few weeks ago, started coming up with the following message on my desktop:
"USB Devices Disabled Unplug the device using too much power to re-enable USB devices".
I unplugged the device and the message still keeps coming up.
This is what I have done so far to troubleshoot:
I shut down the laptop. When booting up I pressed the command+option+p+r at the same time. It comes up with a menu to reinstall OSX, Get help online, Run Disk Utility, etc. I choose the disk utility and repair the disk and then restarted.
The message keeps popping up and I can't seem to get rid of it. Why does the message keep popping up even though I don't have any devices hooked up to the laptop at all? Any help to reenable my usb ports and get rid of the messaage would be helpful.

I talked to Apple Support and we at least stopped the bleeding, a little bit. These are the troubleshooting steps I did before I contacted Apple Support:
1. Reinstalled OSX
2. Restore the last known good Time Machine Backup.
This did not fix my issue, so I called Apple Support and they told me this:
1. Turn Power off.
2. Wait 15 seconds.
3. Plug in Magsafe adapter.
4. Wait 15 seconds.
5. Hold down the Shift+Option+Power Button for 20-30 seconds.
6. Turn Power back on.
Ok, this stopped the bleeding a little, but as soon as I plugged in a Apple USB Superdrive
and a Apple Mini Displayport to VGA Adapter. This "USB Devices Disabled" pop-up pops up like every 30 minutes now. At least, it is not constantly popping up after I close it, so I guess it will do for the temporary. Going to contact Apple support, later, though to see what else can be done.

"Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled." HELP!

When I plug in my son's iPad I get this message "Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled." I only have one charger for this iPad all my other chargers are for iPhone 4s. I have pluggerd it in different outlets around the house and the iPad will not charge. When I plugged it on my lap top to back it up it gave me the warning message. HELP!!

I have the same problem on my Air. The message first came up while my iPhone was connected to it for some time. Since then, it pops up ALL THE TIME, whithout anything being connected to the USB port, at what appear to be random intervals that vary between about one hour and a few seconds. I have tried resetting the SMC and the PRAM, but no results. A quick search revealed that thousands of users are facing this problem, but Apple has yet to provide a solution. Please help!

6600 Fold - Too Much Power

Similar Messages

Maybe you are looking for