6650d Flip front panel switch problem

Can anyone tell me how I disable the front panel switches on my Nokia 6650d flip. Whenever I put this in my pocket the switches are activated whenever I walk: resulting in an annoying beep. It also flattens the battery. It completely negates the point of a flip phone. The phone is OK I just need to know how to disable these annoying buttons. Can anyone help?

To lock the keypad in the standby mode, press the left selection key and * within
1.5 seconds. To set the device to automatically lock the keypad after a certain
time, select > Settings > Phone sett. > General > Security > Phone and SIM
card > Keypad autolock period > User defined and the desired time.
To unlock the keypad, select Unlock, and press * within 1.5 seconds.
When the device or keypad is locked, calls may be possible to the official emergency number
programmed into your device.
To lock the cover keypad, slide your finger on the the left cover touch key and then
the right cover touch key within 1.5 seconds. If you have locked the keypad from
the cover display, and your device goes to sleep mode, you first need to press the
camera key to activate the cover touch keys. To unlock the cover keypad, slide
your finger on Unlock (left cover touch key), and then OK (right cover touch key)
within 1.5 seconds.
If i have helped at all a click on the white star below would be nice thanks.
Now using the Lumia 1520

Similar Messages

How does one empty an array during runtime with a front panel switch

I can 'empty array' from the front panel during runtime but I want to empty all arrays (20) from my vi with a front panel switch (see screenshot). I have used replace array subset and reshape array with no success. Any help would be appreciated
Attachments:
TempScan_screenshot.JPG ‏26 KB

Hmm... You can empty an array by reshaping it or by assigning a constant empty array - using local variables or properies of the original control (see attached example... hmmm... not the best one ). May be you can attach a part of your code to see what is better to do in the given case.
Attachments:
reset_table.vi ‏20 KB

K8N Neo Platinum + Sonata Front Panel Audio Problem

Hello,
The front panel audio speaker output is reversed when using headphones on my K8N Neo Platinum and Antec Sonata case. If I swap the left and right front panel audio output signal connectors, the headphone speakers are fine, but then my normal front speakers are reversed. All other connectors seem to be plugged in correctly. I've tried using nvswap, but doesn't seem to work on nForce3. Currently using Realtek driver version 5.10.0.5620 (had the same problem with the drivers included on mb cd) on WinXP Pro SP1 and 5.1 speaker setup (would like to use FPA for mic/headphones while gaming).
Let me know if you need any additional info.
Thanks.

I am having the same problem as well. Was able to correct front output jack by switching the connections. But rear audio is still backwards. I havent tried any sort of 5.1 or 7.1 channel audio setups

Front Panel LEDs problems for Mega 180

Hi, it's rigth one year I got a Mega 180, and I've not ended yet to tune and optimize it
I admit it's like a hobby now
I immediately ask you for my LEDs problems.
I have read many topics and maybe other people have the same my problem, also if I'm not sure if they treat about the Front Panel LEDs when they speak about the "LCD Display".
I have some switched off LEDs in my front panel, in the "time" displayng and in the volume bar: I have to substituite them? Someone have done it before? It's possible to remove the front panel or I have to disasseble all the pc
Or it's a firmware problem?
I also thank all people that cured the section of optical devices compatibility: last week I bought a new Pioneer 111D, because my LG GSA-4167B was not suitable in the PC mode, for DVD playback.
In fact I had many problems for the DVD fluently playback: I have spent 4 months trying new video codecs and also substituting the video card, then I finally have understood that was an optical device problem.
The Pioneer 111D was perfect in the PC mode, but then I had problems for HI-FI playing mode
Then I finally used my old Pioneer 108, that I had in the old desktop, and all work (I pray) fine both in HI-FI and PC mode.
I'll be very happy also to describe to whom that will ask me, my experience with the Mega 180 "assembling", during the last year, hoping it could be useful for other people.
Thanx

> Hi, I'm new to LabVIEW! Ok, what I'm trying to do is create a front
> panel with 9 LEDs. Then I have a Menu Ring, with three different
> options. These options determine the order in which the LEDs are lit.
> So what I was planning on doing was creating three subVIs, one for
> each of the options...but how can I do that when I only have one
> boolean for each LED? So basically how can I relate the LEDs on the
> front panel into the subVIs? I tried using globals - but it seemed
> like that just passed on the state of the boolean instead of allowing
> me to actually change the boolean in the subVI. I hope this makes
> sense...I'm really confused! Thanks for any help!
Initially, you might just hook your ring to a case structure to
determine which frame exe
cutes. You can put the terminals for the
Booleans in the different diagrams and about the only other thing to
keep in mind is that you probably want a delay in the loop.
Greg McKaskle

Save a front panel image problem

Hi, i'm trying to save at run-time an image of my front panel, and the little code with the Invoke Node (FP.GetImage) works well but there is a problem, i have a background image for my front panel and this image don't show up in the image saved so i have an image with controls and graphs but a blank background. Is there some way to obtain an image of my ENTIRE front panel? Thanks

Hi,
Here's how I got ride of tghis issue, I use Windows "printscreen" function by simulating a keyboard stroke and then I get the data from clipboard (crop it it necessary) and save the image.
What I like about it is that the "crop" makes it easy to get just what I want when there's more than one monitor.
What I don't like is that it's a windows only solution.
Hope it helps
When my feet touch the ground each morning the devil thinks "bloody hell... He's up again!"

NI 5112 Scope soft front panel setting problem

Hi,
I tried to meausre a 5.1 voltage using SCOPE soft front panel. I could get 5.1 AC voltage from SCOPE soft front panel,
but it did not go back to 0 volt after 1 to 2 second in a horizontal line. Nornamlly, my 5,1V will go back to 0 volts
in my oscilloscope after 1 to 2 seconds because I am measureing a shock beep pulse waveform.
Can you tell why?
I am going to give you my setting. I was trying Y-axis 2 volt/div, AC coupe, ch 0, X-axis is 10 microsecond/div. normal mode.
Trigger: edge, rising, ch 0, trigger lever 2.5.
I am in a urgent. Coould you pls send me quickly

I'm sorry if I don't completely understand what the behavior is but if I understand you correctly, you have a signal that goes from 1 volt, peaks at 5.1, and then slowly drops to 1 volt again. That entire signal takes 1 to 2 seconds.
I am not sure if the problem you are seeing is 1. You can never get the full signal in the SFP or 2. You get the signal ok but the SFP does not wait for you to hit a button to try and acquire again.
If the question is number 1
If this is the issue it sounds like you are able to capture the 5 Volt peak, however it never goes back down to 1 volt. You mentioned that you have the X-Axis set to 10 microseconds/ div. Therefore the SFP is only acquiring an total of 100 microseconds, and if the reference is set to 50%, then you are only getting 50 microseconds of signal after the trigger, so you will not be able to acquire the 1-2 seconds it takes for your signal to drop. I would suggest increasing the number of points and slowing down the Time/Division. You should be able to change those settings a few times to actually get 2 seconds worth of signal.
2. If you want to simply hit a button and the SFP will acquire again then you need to change the mode to SGL. Then you just need to hit the run or pause button and the SFP will acquire again.
Message Edited by Evan on 09-12-2005 10:03 AM

Remote front panel reconnection problem

Hello,
I have created a real time application build for myRIO and i can succesfully run it as startup. After MyRIO reboots, through the Project Window i select Operate/Connect to Remote Panel. I enter the local network IP address 192.168.0.101 and port 8000 and the Front Panel of the Startup VI opens. I run it and everything is running as expected.
This setup is installed on a UAV and acquires data from scientific instruments all data is writen on a USB flash drive on myRIO
It is expected that sometimes the local network link will break during the flight. To simulate this i unplugged myRIO from the ethernet cable will the Data is saved.
I noticed the following strange things:
1. At time X i connect to the remote panel and i start the DAQ which acquires data
2. At time X+10 minutes i unplug the ethernet cable which connects myrio to the local network
3. At time X+20 minutes i poweroff myRIO
I was expecting that after the connection was broken the VI would have kept acquiring the Data until myRIO powers off.
Instead i noticed that myrio acquires data for only 1 more minute after the ethernet cable is unplugged.
It is very important that after the UAV takes off whatever happens to the network connection the VI keeps acquiring data for as long myrio is powered on.
I also tried the web publishing tool but i could not connect using a browser. It seems that the web server was not running properly. I also noticed that the html file was not located in the target destination folder. I tried to manually copy it using a map networked drive but the file could not be copied.
I will appreciate any help on the above issues.
Thank you,
Christos

I see thank you. Very funny because i thought i had to do something with duplicating the real time target.
So regarding the above problem, is there any way to be connected remotely to the target and when the link is broken to reconnect without affecting the operation of the VI running?
For example, lets assume we connect to a remote front panel which has a simple VI with just a 1 second period timed loop running and for each iteration of the loop i monitor and i save the index of the loop. When i connect to the VI i request control and i click run. The VI starts running. After one minute, at loop iteration 60 the link between the host and the target breaks. The VI should continue running.
After 1 minute of broken link the network is again available.
What can i do to re-establish connection without affecting the VI operation and continue monitoring the VI. If reconnecting after 1 minute i will be expecting to see the loop iteration to be 120 and keep running. Is there any way to do this?

FRONT PANEL AUDIO PROBLEM

Ok i have a Hp pavillion m7480n and yesterday i bought a new graphic card (Nvidia geforce gt220) so i installed the card correctly and everything went well. When i restarted my pc the sound in the taskbar said something about HD. The graphic card has a HDMI out so i guess that after installing the card, the audio went to default HD wich i really didnt want to cuz i do not have a hd monitor.
then i downloaded, reinstalled, uninstalled, reboot, installed again the realtek hd audio driver cuz thats what i thought it was but nothing worked ! so now if i want to use my mic i have to plug in the device at the back of my pc wich is really annoying cuz i change alot.
i really tried everything from going to the bios setup to enable "onboard audio", reinstalling drivers, realtek sound manager options "mute rear output device, when a front headphone plugged in." "enable jack detection when device is plugged in".... so i dont know what else i can do about it... really need help ! and by the way i noticed that on my realtek HD audio manager the "Front panel" is grayed i cant click on both of the inputs heres a link to the screenshot
http://img267.imageshack.us/img267/9473/picyy.jpg
and on this screenshot i there is some level (green bars) on the mic but beleive me its not working.
i beleive that theres a possibility that a wire disconnected when i installed my graphic card but i want to be sure its not a simple driver problem or whatever else before playing with the wires inside.

had the same issue, its the graphics card since it has an integrated HD audio, it causes a conflict, what you have to do is restart the PC, hit either F1 or F10 to go to setup, then go to where it says sound, and you have to change it to onboard device
after that both should work

Z87-G43 Board Front panel USB Problem

I have installed the board and windows 7 64bit
Updated the Bios and checked everything I could. I do NOT get the connect tones from anything I connect to the front panel USB ports. I have used 2 (KNOWN GOOD, works on other machines) connector sets with 2 ports each, and ALL of the ports have the same symptoms. All of the usb devices have the connect tones when inserted to any of the rear ports. I have not tried the USB3 port for the front because I do not have the wiring and related header connector. My phone, (Samsung GS4) when connected to the rear ports always opens an explorer window showing the Ext SDCard and the Internal memory. when I connect to any of the front panel ports, no sound, no pop-up of explorer, but I do see the device when I manually open explorer and can open the connection manually.
I am at a loss as to what is not right and how I can make it work correctly. If anyone can give me any information to correct this, I'd be very grateful. (Tech Support was no help)
Thank you, and Aloha From Hawaii!

Thank you for your reply.
I have an older Antec Case and I have tried a brand new front panel connector I got from Frys and it acts the same Way. the only difference is that the connector is a one piece assembly that connects directly to the mobo header pins. the one in the case has individual pin connectors. both systems end up with the same scenario. When I plug in a thumb drive, there is no connect or disconnect sound and I still can manually open explorer and access the thumb drive or my phone but nothing pops up to signify any port access.BTW, I am a systems engineer and have spent the last 13 years building machines for a transportation company (bus) My previous board in the same case used the front panel connection and it worked just fine, but since the board died and was only supportive of XP I decided to upgrade to Win 7 64bit and have 16gb ram. All the rear connectors work just fine, but I need all of them so have to use the front panel connection for phone, and thumb drive access. I suspect the mobo has a design problem. The tech support person had no suggestion to correct this problem too! :<(

MSI K9A2-CF front panel audio problem

Just rebuilt a computer using the board. Please note, I have not updated the BIOS at all and I am using XP Pro. Anywho, I've tried everything under the sun, so far, aside from previously stated, to get this sucker to work. I have it connected properly, I've installed every audio driver on the motherboard CD. I can't find a setting in the BIOS to turn on front panel audio either. Everything else works fine though. USB's, HD audio connections in the back, etc. The program in windows will detect all inputs except for the front audio in and out.
I'm a bit stumped. Any suggestions?

Quote from: Bas on 17-August-09, 22:22:14
You have to check the wires on the plug, looks like they are wrong or the case-module is broken somewhere.
You have to start checking and measuring with an Ohm-meter.
Remember, neither case front worked. I'm not saying it couldn't be the case, but I'll try to get my hands on an Ohm-meter. Where can I find out what values I'm looking for? I know next to nothing about testing to that extent.
Also, what if it's the motherboard itself? Isn't there somewhere in the bios and/or windows device manager that I can confirm whether or not the device itself is working, or not working, properly?
Thanks for your replies so far.
Mike,
I honestly don't know, but the case only has one audio cable, and the MB only has one audio plug-in for the front panel. I have both drivers installed. The on-board audio plug-in on the rear of the computer works fine. I can get sound, etc, no problem from the rear. Front panel only is not working.

Z87-G43 : JAUD1 front panel connector problem

Hi everyone,
I received this mb two days ago, everything was working fine until i decided to plug my headphones in the front panel jack of my Zalman Z12 plus...
There is like an "underwater" effect that makes the sound pretty bad. The rear jacks work flawlessly.
Any clues ? Any feedbacks ?
I've tried to :
- reinstall the latest realtek driver : still
- use another headset : still
Maybe the mb is faulty, maybe the case is...
Thanks.

Quote from: Ppgtjmad on 08-February-14, 20:42:32
Hello,
Thanks for the feedback. I found the culprit : broken front panel audio connectors on my Zalman Z12 Plus.
What case do you have ?
Glad to hear that you figured it out.
Cooler Master 430 Elite (in my sig.).
Yogi

Front Panel Audio Problems

I'm trying to make sense of the JAUD1 descriptions and enable the front panel audio jacks to work but it seems the mobo doc and the casing connectors have entirely different descriptions.
The JAUD1 has these:
Pin1 AUD_MIC
Pin2 AUD_GND
Pin3 AUD_MIC_BIAS
Pin4 AUD_VCC
Pin5 AUD_FPOUT_R
Pin6 AUD_RET_R
Pin7 HP_ON
Pin8 Key
Pin9 AUD_FPOUT_L
Pin10 AUD_RET_L
The casing's connectors are:
Mic:
MICOUT
MICIN
AGMD (Ground???)
LineIn:
SPKO-R
SPKO-L
LineOut:
EARO-R
EARO-L
Reserved
What is going on??? Please help! ;(

Although it doesn't make sense as LineIn - SPKO_L/SPKO_R, I read as Speaker Out though. EARO_L/EARO_R should be headphone out.
Pin1 AUD_MIC - MICOUT
Pin2 AUD_GND - AGMD
Pin3 AUD_MIC_BIAS - MICIN
Pin4 AUD_VCC
Pin5 AUD_FPOUT_R - EARO_R
Pin6 AUD_RET_R - SPKO_R
Pin7 HP_ON
Pin8 Key
Pin9 AUD_FPOUT_L - EARO_L
Pin10 AUD_RET_L - SPKO_L

Front panel audio problem Neo2 Platinum

Hi
I have a S775 915P Neo2 Platinum motherboard which I would like to connect to a Thermaltake Tsunami Case (front panel) but I don't know how to do this since the names on the cables from the case don't match the motherboard.
The cables from the case has the following names:
MIC VCC
MIC IN
RETURN L
RETURN R
EAR R
EAR L
GROUND
...and on the motherboard:
PORT 1L
GND
PORT 1R
PRESENCE#
PORT 2R
SENSE1_RETIRN
SENSE_SEND
KEY
PORT 2L
SENSE2_RETIRN
How do I connect theese?
Thanks!
//Thomas

Not the same MoBo, but maybe some of these links will help,
https://forum-en.msi.com/index.php?topic=72497.0
https://forum-en.msi.com/index.php?topic=62730.0
Personally I prefer USB in front and Audio back with a mediahub /adapter on the monitor.
Cheap, simple and functionally.

Z77A-GD65 and front panel audio problem !!

I have a Z77A-GD65 and a case CM 690 II advanced window, and i connected the front panel audio correctly in the right port, and when i plug my headphones in the front audio jack, there is no sound !!!
Please help me !!

Quote from: CalinTM on 11-May-12, 16:25:29
Ok, i've did this thing, now works, but the sound sounds only in the right side of the headphones, and the sound is very very slow....
which of the 2 audio header plugs did you connect to the mother board ac97 or HDaudio?
have you connected the headphones to the rear pannel connector of the motherboard to see if its better?

Xonar D1 front panel microphone not working in kernel 2.6.33

It is not possible to record anything from my front panel microphone jack after I updated kernel to 2.6.33.
It still works OK with kernel 2.6.32.10, but does not work with 2.6.33.3, and it did not work with 2.6.33.rc8 too. The front panel switch in alsamixer switches only output but not input (mic) now. Before, the switch had impact on both output and input.
When I activate the back panel on the card everything is working well (back panel connectors are active, front panel connectors are inactive). When I activate the front panel then the front panel microphone is not working (back panel microphone works). The alsamixer front panel switch does not have impact on the microphone any more and no switch was added to control the microphone separately from the output.
The alsa version is 1.0.23.
I use 32 bit kernels. My brother uses 64 bit kernels and the problem is the same for him too. Although he uses Xonar DX.
Any idea how to get this fixed?

I'm also having trouble with the 2800pci driver. I installed the v26 firmware from the PKGBUILD in this thread, and it does scan as Cdh says, but will not connect...
$ dmesg | grep rt2800pci
rt2800pci 0000:04:01.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
Registered led device: rt2800pci-phy0::radio
Registered led device: rt2800pci-phy0::assoc
Registered led device: rt2800pci-phy0::quality
rt2800pci 0000:04:01.0: firmware: requesting rt2860.bin
phy0 -> rt2800pci_mcu_status: Error - MCU request failed, no response from hardware
Should it really be loading all these modules just to use rt2800pci?
$ lsmod | grep 'rt'
rt2800pci 9547 0
rt2800lib 21101 1 rt2800pci
rt2x00usb 7607 1 rt2800lib
rt2x00pci 5005 1 rt2800pci
crc_ccitt 1307 1 rt2800pci
rt2x00lib 25148 4 rt2800pci,rt2800lib,rt2x00usb,rt2x00pci
led_class 2609 1 rt2x00lib
mac80211 171772 3 rt2x00usb,rt2x00pci,rt2x00lib
cfg80211 126658 2 rt2x00lib,mac80211
iTCO_vendor_support 1873 1 iTCO_wdt
eeprom_93cx6 1352 1 rt2800pci
usbcore 144604 6 usbhid,rt2x00usb,usb_storage,uhci_hcd,ehci_hcd
rtc_cmos 8990 0
rtc_core 14439 1 rtc_cmos
rtc_lib 1842 1 rtc_core
The rt2860sta driver does work, but only at G speed not N. I also tried the ralink 2.3.0.0 driver, but it is even slower than the kernel driver. With 2.6.32 kernel, I was able to get N speed from their 2.1.2.0 driver, but that one won't compile anymore. I've had nothing but trouble with this card for the last year.
I'm very tempted to just buy another card, but I'm not sure which one to buy.

6650d Flip front panel switch problem

Similar Messages

Maybe you are looking for