6790 - start up sound

Is there any way to turn off or change the start up sound on the 6790 slide?  I find it annoying.
Thanks

On some phones you have the provision for ON/OFF the startup tone.. Check in phone settings if its there.. else not possible...
--------------------------------------------------​--------------------------------------------------​--------------------------------------------------​--If you find this helpful, pl. hit the White Star in Green Box...

Similar Messages

  • Start Navigation sound in Windows 7 64 bit dissappeared

    ? [size="">I have been scratching my head over this one.
    [size="">After doing a clean install of Windows 7 64 bit on a new build this week, and installing a new X-Fi PCIe Titanium Fatality Pro, I found the start navigation windows sound was no longer there - I am talking about the brief sound you hear, that sounds like a click, when you click a link, double click a folder to open , etc. I could find the sound in windows sounds, but when I pressed test I could not hear it.
    [size="">
    [size="">After much trial and error, I discovered that I had to disable sound blaster enhancements, in the properties tab for speakers in the sound card settings. I now have that windows sound back.
    [size="">When I enable sound blaster enhancements, it goes away, when I disable them, it is back to normal.
    [size="">
    [size="">Is this normal or unique to me?

    Wow, that fixed? my problem also by disabling soundblaster enhancements. How were you able to figure that one out? I was trying to figure it'sout also many months ago when I first got windows 7 beta and couldn't do it. Anyway,
    Seems like most people don't like this start navigation sound, but I do.
    I don't like the fact of having to disable soundblaster enhancements also.
    Have you noticed that if you change the windows theme to something else it will actually work?

  • When I went to turn the desktop on, the start up sound came on.  Then the screen was white with an icon flashing. The icon is a file folder with a question mark on it.  I cannot get it to fully turn on.  HELP

    When I went to turn the desktop on, the start up sound came on.  Then the screen was white with an icon flashing. The icon is a file folder with a question mark on it.  I cannot get it to fully turn on.  HELP

    Run a disk repair tool on the hard disk or install a new OS.
    (59898)

  • My iMac won't boot, get a black screen with alarm sound, then gray screen with start up sound, then repeats

    this problem started last fall after upgrading to Mavericks. If I shut down my computer (or restart) I have problems getting it going again. This is getting progressively worse. I hadn't shut down in over a month, forgot about this issue and shut down (which I used to do daily), so now I can't get my computer to boot. When I hit the power button I hear it starting, then a loud alarm sounds, then a long pause then start up sound with a gray screen with a progress bar. Once the progress bar fills, the screen goes black again for a bit. This whole process will repeat until I get frustrated and force - shut down by holding the power button. I have tried reseting the pram, starting up in safe mode, starting up with the command - R, starting up with my original install disc... none of it works. I'm at a loss! I do have an external hard drive that I have been using for Time Machine, but it's not recent because the disc needs repairs and I hadn't gotten around to buying a new HD to back up to first. Has anyone else had this problem? I really can't afford a big repair/replacement bill.

    A long, steady, load tone followed by a progress bar can indicate it is trying to install a Firmware Update.  Any other Tones would be multiple beeps and show an error code.
    http://support.apple.com/kb/HT5860
    You can also see a progress bar similar to booting into Safe Mode. However, the firmware update bar is thinner vertically than the Safe Mode bar.
    http://support.apple.com/kb/ht1455
    Either way, I would say something is wrong and it would be better evaluated at an Apple Store as Kappy points out.

  • HT3964 My MacBook Pro will not boot up. The screen remains dark although the the comput makes the characteristic start up sound. The sleep light is showing.

    MY MacBook Pro will not boot upThe screen is dark, but the sleep light is on and it makes the characteristic start up sound.What is wrong?

    There is always the forum for MBP
    MacBook Pro
    https://discussions.apple.com/community/notebooks/macbook_pro
    https://discussions.apple.com/community/mac_os?view=discussions 
    http://www.apple.com/support/macbookpro

  • My start up sound is gone after I got the Maverick for my MacBook Pro. Is that supposed to happen?

    I just uploaded Maverick onto my MacBook Pro and now the start up sound is gone. Is that supposed to happen?

    Hmm.....I tryed that and there isn't anything that pertains to the start up sound. I guess I have to keep searching. Thanx for the help though.

  • Question re start-up sound

    I have an iMac 10.6.8 how do you shut off just the start-up sound without turning off the muting volume
    Thanks
    Deej1

    Silence Your Mac Boot Startup Sound Altogether
    How to Mute the Mac Startup Sound
    How to Disable the Mac Boot Chime Completely
    How To Turn Off Startup Sound

  • Hello I got a iPad mini in January and speakers are started to sound right can you help

    Hello I got a iPad mini in January and the speakers have starting to sound like they are not working propyl can you help thank you

    Hi antony136,
    Thanks for visiting Apple Support Communities.
    If you are not able to hear clearly through your iPad mini speakers, start with the troubleshooting steps in this article:
    iOS: Can't hear through the receiver or speakers
    http://support.apple.com/kb/ts1630
    Note that some steps refer to troubleshooting on an iPhone, but the steps can help with an iPad mini as well.
    Regards,
    Jeremy

  • Is there a way to shut off the start-up sound?

    how do I turn off the start-up sound that plays when I turn on my macbook?

    Try downloading Psst from www.macupdate.com. There is also another, called something like startupchime.prefpane or something like that. Look around macupdate using words like chime and startup chime, and you'll find a way.

  • Video started to sound awful when i've updated to iOS6, how can this be fix?

    Hi,
    Ever sine i've updated to iOS6 this October, the sound of my videos on my iPad started to sound awful. I'm using the default video player for iPad. It sounds like there's an echo, bass sounds has totally low quality and etc.
    I tried removing the videos(music video) on my iPad then resync it but it still sounds different from before. I've tested the sounds in my mp3 (same song) still sounds as expected. So my sound setting and my headset are not defective.
    Please teach me how can i fix this issue.
    Thanks

    What app are you using?
    Do you get sound from the YourTube app
    From other website?
    I suspect a problem with the specific site you are using, not an iPod problem. Can you post a link to that site?

  • How can I disable start up sound?

    how can I disable start up sound?

    Welcome to the Apple Discussions!
    http://www.silvermac.com/2006/mac-os-x-start-up-sound-volume-control/
    It's a preference pane control that allows you to adjust the volume of the startup sound or disable it completely.
    Hope this helps!
    -Mike

  • My imac turns on with start up sound then nothing else just the timer going round

    my imac turns on with start up sound then nothing else just the timer going round

    Try restarting holding down the SHIFT key. That will do a directory check in Safe mode. It will take longer to start so continue to be patient.
    If it starts in Safe mode, then restart normally and see how that goes.

  • Macbook without start up sound

    Good morning everyone.
    I´ll tell you a little about my problem. I have a macbook 13" mid 2010 mod A1342. Last week, after cleaning with a cleaning foam for PC´s, I think i used so much foam into the keyboard, because i started up and wont start, i let pass time and tried to start up, it started but some keys was in dead short, and the laptop turns off, i cleaned again with fairly isopropyl alcohol in the entire surface and the back of the keyboard, i wait for it to dry for 2 days and the in tried again, the mac start and works fine without pushing any key, but some key was making dead short, i was using my iphone as a wireless keyboard the trackpad works fine.
    Consulting with an apple tech center they pdiagnosed the keyboard probably was in dead short and but i have to left them to a entire diagnose.
    I buy the piece(upper case) and i replaced by my self (i´m a desktop support techinician for mac and windows), the macbook works fine again with all the keys including mutimedia keys. but the start up sound was gone, now the sound is very low, the speakers works fine i probe it whit de audio midi config. app, i disconnect the speaker off the board, the spearkers of the keyboard works fine but with a very low sound, when i put a headphone or an external speakers the soud works very fine and with a hig volume.
    Due to the constant reebots without turn off properly, the volume(image) of the mac was corrupt, i´ve tried to repair it with the Disc Utility app but the volume was very damaged, i tried to reinstall preserving my files but there´s no oprtion for that , the only option was a clean installation. i think a clean installation fix the trouble, but the sound was the same, after installing all the updates to this day, the result was the same. In the information menu displays onboard sound, in the prefs pane the output have onboard sound to play sounds, i configured into the audio and midi app the stereo option, bunt the sound is still low.
    I don´t think the problem was the logic, beacuse it plays sound into headphones and the internal speaker and the keybooard speaker, the problem is only the startup sound gone and the level of the sound is very low (sound like a cell phone). i tried to reset the PRAM, in the faqs apple say that i have to hear 2 startups sounds and the i have to realease the pushed keys, but in my case there´s no sound, the laptop restart as they say, but without sound, i´m not sure if the PRAM was restored or not, i push the keys (cmd+op+p+r) turn the MB it try to start the a little bit reboot by it self, tyr to start, again reboot by it self, but without sound, if i keep pushing the keys the procees won´t stop, if i release the keys the macbook start fine(without sound), but i not sure if the PRAM was restored.
    I hope anyone can help me.

    i also got this kind of problem recently. i was connected to a speaker n the start up sound just didnt come out till i plugged out the speaker jack. this happen after i finished reinstalling my mac os x (snow leopard) including the updates. the condition worsen by having a delay when i started up my mbp for the 3rd or 4th times. the screen just black n i got a delay for 3 to 4 seconds till finally i heard the start up sound back n see the apple logo n the loading gear came out. i later restarted the mbp again to see whether the same problem occurs bt somehow it didnt. weird things happen to my mbp these days.. what should i do? any suggestion? :O

  • How can I turn off Start up Sound?

    How can I turn off the start up sound, on both my 10.7.5  iMac 24" Late 2006 and my 10.8.3  iMac 27" Late 2009 Mountain Lion.
    Plus my Superdrive has stopped working on both Computers. Please help asap.
    With kind regards, and many thanks.

    The best way to turn off the startup sound is to mute speakers before turning off your computer.
    Also, apps that help you turn off the startup sound don't work with iMacs. There's a command that will allow you to turn it off without muting your speakers. See > http://osxdaily.com/2012/11/04/disable-mac-boot-chime/

  • The Start up sound - shutting it of?

    Hi!
    I've got a MacBook and I really want to know how to cancel the start up sound. You know, you turn the power on, the screen is lit, you hear som mechanic noises from the machine waking up and then Boom the starting sound of Doom let's everyone know Jakob has just turned his notebook on. Mostly irritating and a bit embarrassing when sitting in a quiet study hall.
    Have a good one
    Jakob
    (oh and turning the sound all the way down doesn't help)

    Cheers mate

Maybe you are looking for

  • How to create chordsymbols in a SMF to perform with a Tyros (XF) Yamaha

    Hello. I try to create Standard Midi Files in Logic Pro 7 to perform it with a Yamaha Tyros 1 Keyboard. For my performing I like to have a "classical realtime leadsheet" on the display - chordsymbols, lyrics and the leadvocal line. I got a problem wi

  • Warp certain areas in a photo, PLEASE help.

    I know that PSE 9 does not come with a "warp" feature (in transform or free transform). Example scenario: In a photo of a face, I want to flatten or extend his nose. Is it possible to select a certain area of photo and distort that area. Or any sugge

  • How to get the server name/hostname on which JVM is running?

    How to get the server name/hostname on which JVM is running from the Servlet or normal class?

  • Upgrade Cisco Prime LMS 4.0 to Cisco Prime Infrastructure 2.1

    My company has asked me to migrate Prime LMS 4.0 to Prime Infrastructure 2.0 for a client and can not find the guide, the questions are? the migration is possible without an intermediate step? and There is a guide to update LMS 4.0 to PI 2.0 ?? Thank

  • Column / Row Spanning in UIX table

    Hi There, Anybody know how to achieve column/row spanning when using the uix databound table? For example, i would like a table which looked similar to the following:      | Cell1  | Cell2 | Cell3 |      | A spanned cell         |      --------------