6800 performance and architecture

hey !
I was reading the white papers on 6807-XL, 6880-X and Sup2T and i have some questions. I will start of by apologizing for my bad English.
Many of my questions is about the 6880-X chassi and i have read these white papers
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-6880-x-switch/white_paper_c11-728540.html
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-6500-series-switches/white_paper_c11-696669.html
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-6807-xl-switch/white_paper_c11-728264.html
My understanding is that the switch fabric in 6880-X consists of 24 fabric channels and that every module slot gets 4 of these channels. 1 channel can operate in 40 or 55Gbps depending on the clock frequencies of the SerDes lanes. I also read that only 2 of these channels are active and that 2 are there for future use. This means that every slot can have a switch fabric connection consisting of 80 or 110Gbps. The 6880-X linecards consists of 16 SFP/SFP+ ports but only has a 80Gbps switch fabric connection(2*40Gbps).
1. Is this correct or have i missed something?
2. Is it possible to configure only 1 line card in performance mode and leave the rest at default?
Does anyone know how the fabric channel is chosen on incoming and outgoing flows? If you run 6880-X in VSS you have 4 active fabric channels, how does the flows balance over these 4 fabric channels? Or the 2 fabric channels without VSS. Is it a hashing algorithm similar to etherchannels, like the one used in X6904-40G on the 4*16Gbps internal channels?
These SFP/SFP+ ports is also said to support 40Gbps with a SFP-to-QSFP module but since the port complex is based on the X6904-40G linecard it wont be possible to achieve 40Gbps linerate. Since one flow is loadbalanced over 1 16Gbps internal channel.
3. Is this correct or have i missed something?
Looking at the schematics of the port complex i see that the connection between Port ASIC and MUX FPGA consists of 8*6.25Gbps.
4. Is the incoming and outgoing flows loadbalanced over all of these connections or can one flow only use one of these 6.25Gbps connections?
5. If it is loadbalanced does anyone know the hash algorithm?
6. Does anyone know if and when there will be 40Gbps linecards to 6807-XL?
7. Does anyone know if the planned 32*10Gbps linecard for 6807-XL will use 4 fabric channels to run all 32 ports in linerate?
I hope i have placed this topic in the right section.

it all depends if your question is with the same processor.
if we're comparing both with 2.5GHz - the Retina might seem faster because of the flash storage.
if you install a SSD in the non retina Macbook Pro - the retina version will still boot faster but once the boot up process is done. Speed will be similar between the two since the non Retina has a SSD installed.
As for the fastest SSD out there:
Kingston Hyper X - I have this in my late 2011.
Samsung 840 Pro - one of the fastest one out there.
Sandisk Extreme - was one of the fastest last year.

Similar Messages

I need a clarification : Can I use EJBs instead of helper classes for better performance and less network traffic?

My application was designed based on MVC Architecture. But I made some changes to HMV base on my requirements. Servlet invoke helper classes, helper class uses EJBs to communicate with the database. Jsps also uses EJBs to backtrack the results.
I have two EJBs(Stateless), one Servlet, nearly 70 helperclasses, and nearly 800 jsps. Servlet acts as Controler and all database transactions done through EJBs only. Helper classes are having business logic. Based on the request relevant helper classed is invoked by the Servlet, and all database transactions are done through EJBs. Session scope is 'Page' only.
Now I am planning to use EJBs(for business logic) instead on Helper Classes. But before going to do that I need some clarification regarding Network traffic and for better usage of Container resources.
Please suggest me which method (is Helper classes or Using EJBs) is perferable
1) to get better performance and.
2) for less network traffic
3) for better container resource utilization
I thought if I use EJBs, then the network traffic will increase. Because every time it make a remote call to EJBs.
Please give detailed explanation.
thank you,
sudheer

Please suggest me which method (is Helper classes or Using EJBs) is perferable :
1) to get better performance
EJB's have quite a lot of overhead associated with them to support transactions and remoteability. A non-EJB helper class will almost always outperform an EJB. Often considerably. If you plan on making your 70 helper classes EJB's you should expect to see a dramatic decrease in maximum throughput.
2) for less network traffic
There should be no difference. Both architectures will probably make the exact same JDBC calls from the RDBMS's perspective. And since the EJB's and JSP's are co-located there won't be any other additional overhead there either. (You are co-locating your JSP's and EJB's, aren't you?)
3) for better container resource utilization
Again, the EJB version will consume a lot more container resources.

Ask the Experts: IOS-XR Fundamentals and Architecture

Welcome to the Cisco Support Community Ask the Expert conversation.
Learn and ask questions about IOS-XR Fundamentals and Architecture.
November 18, 2014 through November 28, 2014.
Cisco IOS XR Software is a modular and fully distributed network operating system for service provider networks. Cisco IOS XR creates a highly available, highly secure routing platform.
It distributes processes across the control, data, and management planes with their own access controls and delivers routing-system scalability, service isolation, and manageability.
This is a Q&A extension of the Live expert Webcast.
Cisco subject matter experts Sudeep, Raj, and Sudhir, will focus on IOS-XR fundamentals.
Including:-
High-Level Overview of Cisco IOS XR
Cisco IOS XR Infrastructure
Configuration Management
Cisco IOS XR Monitoring and Operations
Cisco IOS XR Security
Introduction to different IOS-XR platforms
Sudeep Valengattil is a customer support engineer in High-Touch Technical Services at Cisco specializing in service provider technologies and platforms. Sudeep has got experience on XR platform like ASR9000, CRS, NCS and GSR. Sudeep has more than 9 years of experience in the IT industry and holds CCIE certification (36098) in Service provider.
Sudhir Kumar is a customer support engineer in High-Touch Technical Services at Cisco specializing in service provider technologies and platforms. His areas of expertise include Cisco CRS, ASR 9K and Cisco XR 12000 Series Routers. Sudhir has more than 10 years of experience in the IT industry and holds CCIE certification (35219) in Service provider and Routing and switching.
Raj Pathak is a customer support engineer in High-Touch Technical Services at Cisco specializing in service provider technologies and platforms. He serves as a support engineer for technical issues supporting Cisco IOS XR Software customers on Cisco CRS and Cisco XR 12000 Series Routers. Raj has more than 8 years of experience in the IT industry and holds CCIE certification (38760) in routing and switching.
For more information about this topic, visit the Expert Corner > Knowledge Sharing
Remember to use the rating system to let the experts know if you have received an adequate response.

Hi Charles,
To answer your question,
LPTS would be acting only on packet/traffic which is ingressing the router and destined for the router itself (for-us packets). It provides an internal forwarding table to route control/management protocol packets destined to local router to the right application for further processing. Once we have a packet entering the interface, the network processor would be performing a lookup to determine, if this packet is destined for us. Based on which, it will forward to LPTS. For eg, the ICMP packets coming in on an interface with destination IP of router itself, would be processed by LPTS. It also provides policing function for this traffic transparently.
Key facts about LPTS
1. LPTS is an always on feature. No user configuration needed to enable it.
2. LPTS is only applicable for traffic entring to the router and destined to the local router. Applies for control-plane and management plane traffic.
3. Packets originated by router and transit traffic is not processed by LPTS
4. LPTS polices the incoming traffic based on the pre-defined policer rates.
Here is an o/p snip to view the LPTS entries.
RP/0/RP0/CPU0:CRS-C#sh lpts pifib hard police loc 0/0/cpu0
Tue Nov 25 23:32:10.666 EDT
Node 0/0/CPU0:
Burst = 100ms for all flow types
FlowType Policer Type Cur. Rate Def. Rate Accepted Dropped
unconfigured-default 100 Static 500 500 0 0
L2TPv2-fragment 185 Static 700 700 0 0
Fragment 106 Static 1000 1000 0 0
OSPF-mc-known 107 Static 20000 20000 44818 0
OSPF-mc-default 111 Static 5000 5000 11366 0
Do let us know if you have any further queries.
Regards,
Sudeep Valengattil

Nice to see 13" retina but it has only Intel HD Graphics 4000 and does not have NVIDIA GeForce GT 650M with 1GB of GDDR5 memory card. How it will affect the speed, performance and other things compared to 15" retina where NVIDIA GeForce card is available.

Nice to see 13" retina but it has only Intel HD Graphics 4000 and does not have NVIDIA GeForce GT 650M with 1GB of GDDR5 memory card. How it will affect the speed, performance and other things compared to 15" retina where NVIDIA GeForce card is available.

The 15" Retina's will have better performance than any 13" Retina. Not only do the 15" machines have dedicated GPU's, but they also have quad-core processors, whereas the 13" Retina's only have dual-core processors.

QUERY PERFORMANCE AND DATA LOADING PERFORMANCE ISSUES

WHAT ARE QUERY PERFORMANCE ISSUES WE NEED TO TAKE CARE PLEASE EXPLAIN AND LET ME KNOW T CODES...PLZ URGENT
WHAT ARE DATALOADING PERFORMANCE ISSUES WE NEED TO TAKE CARE PLEASE EXPLAIN AND LET ME KNOW T CODES PLZ URGENT
WILL REWARD FULL POINT S
REGARDS
GURU

BW Back end
Some Tips -
1)Identify long-running extraction processes on the source system. Extraction processes are performed by several extraction jobs running on the source system. The run-time of these jobs affects the performance. Use transaction code SM37 Background Processing Job Management to analyze the run-times of these jobs. If the run-time of data collection jobs lasts for several hours, schedule these jobs to run more frequently. This way, less data is written into update tables for each run and extraction performance increases.
2)Identify high run-times for ABAP code, especially for user exits. The quality of any custom ABAP programs used in data extraction affects the extraction performance. Use transaction code SE30 ABAP/4 Run-time Analysis and then run the analysis for the transaction code RSA3 Extractor Checker. The system then records the activities of the extraction program so you can review them to identify time-consuming activities. Eliminate those long-running activities or substitute them with alternative program logic.
3)Identify expensive SQL statements. If database run-time is high for extraction jobs, use transaction code ST05 Performance Trace. On this screen, select ALEREMOTE user and then select SQL trace to record the SQL statements. Identify the time-consuming sections from the results. If the data-selection times are high on a particular SQL statement, index the DataSource tables to increase the performance of selection (see no. 6 below). While using ST05, make sure that no other extraction job is running with ALEREMOTE user.
4)Balance loads by distributing processes onto different servers if possible. If your site uses more than one BW application server, distribute the extraction processes to different servers using transaction code SM59 Maintain RFC Destination. Load balancing is possible only if the extraction program allows the option
5)Set optimum parameters for data-packet size. Packet size affects the number of data requests to the database. Set the data-packet size to optimum values for an efficient data-extraction mechanism. To find the optimum value, start with a packet size in the range of 50,000 to 100,000 and gradually increase it. At some point, you will reach the threshold at which increasing packet size further does not provide any performance increase. To set the packet size, use transaction code SBIW BW IMG Menu on the source system. To set the data load parameters for flat-file uploads, use transaction code RSCUSTV6 in BW.
6)Build indexes on DataSource tables based on selection criteria. Indexing DataSource tables improves the extraction performance, because it reduces the read times of those tables.
7)Execute collection jobs in parallel. Like the Business Content extractors, generic extractors have a number of collection jobs to retrieve relevant data from DataSource tables. Scheduling these collection jobs to run in parallel reduces the total extraction time, and they can be scheduled via transaction code SM37 in the source system.
8). Break up your data selections for InfoPackages and schedule the portions to run in parallel. This parallel upload mechanism sends different portions of the data to BW at the same time, and as a result the total upload time is reduced. You can schedule InfoPackages in the Administrator Workbench.
You can upload data from a data target (InfoCube and ODS) to another data target within the BW system. While uploading, you can schedule more than one InfoPackage with different selection options in each one. For example, fiscal year or fiscal year period can be used as selection options. Avoid using parallel uploads for high volumes of data if hardware resources are constrained. Each InfoPacket uses one background process (if scheduled to run in the background) or dialog process (if scheduled to run online) of the application server, and too many processes could overwhelm a slow server.
9). Building secondary indexes on the tables for the selection fields optimizes these tables for reading, reducing extraction time. If your selection fields are not key fields on the table, primary indexes are not much of a help when accessing data. In this case it is better to create secondary indexes with selection fields on the associated table using ABAP Dictionary to improve better selection performance.
10)Analyze upload times to the PSA and identify long-running uploads. When you extract the data using PSA method, data is written into PSA tables in the BW system. If your data is on the order of tens of millions, consider partitioning these PSA tables for better performance, but pay attention to the partition sizes. Partitioning PSA tables improves data-load performance because it's faster to insert data into smaller database tables. Partitioning also provides increased performance for maintenance of PSA tables for example, you can delete a portion of data faster. You can set the size of each partition in the PSA parameters screen, in transaction code SPRO or RSCUSTV6, so that BW creates a new partition automatically when a threshold value is reached.
11)Debug any routines in the transfer and update rules and eliminate single selects from the routines. Using single selects in custom ABAP routines for selecting data from database tables reduces performance considerably. It is better to use buffers and array operations. When you use buffers or array operations, the system reads data from the database tables and stores it in the memory for manipulation, improving performance. If you do not use buffers or array operations, the whole reading process is performed on the database with many table accesses, and performance deteriorates. Also, extensive use of library transformations in the ABAP code reduces performance; since these transformations are not compiled in advance, they are carried out during run-time.
12)Before uploading a high volume of transaction data into InfoCubes, activate the number-range buffer for dimension IDs. The number-range buffer is a parameter that identifies the number of sequential dimension IDs stored in the memory. If you increase the number range before high-volume data upload, you reduce the number of reads from the dimension tables and hence increase the upload performance. Do not forget to set the number-range values back to their original values after the upload. Use transaction code SNRO to maintain the number range buffer values for InfoCubes.
13)Drop the indexes before uploading high-volume data into InfoCubes. Regenerate them after the upload. Indexes on InfoCubes are optimized for reading data from the InfoCubes. If the indexes exist during the upload, BW reads the indexes and tries to insert the records according to the indexes, resulting in poor upload performance. You can automate the dropping and regeneration of the indexes through InfoPackage scheduling. You can drop indexes in the Manage InfoCube screen in the Administrator Workbench.
14)IDoc (intermediate document) archiving improves the extraction and loading performance and can be applied on both BW and R/3 systems. In addition to IDoc archiving, data archiving is available for InfoCubes and ODS objects.
Hope it Helps
Chetan
@CP..

Welcome to the Solutions and Architectures Data Center & Virtualization Community

Welcome to the Solutions and Architectures Data Center & Virtualization Community. We encourage everyone to share their knowledge and start conversations related to Data Center and Virtualization Solutions and architectures.All topics are welcome, including Servers – Unified Computing, Data Center Security, Data Center Switching, Data Center Management and Automation, Storage Networking, Application Networking Services and solutions to solve business problems.
Remember, just like in the workplace, be courteous to your fellow forum participants. Please refrain from using disparaging or obscene language or posting advertisements.
Cheers,
Dan Bruhn

Hi,
I have a question...
I going to install two Nexus 7009 with three N7K-F248XP-25 modules on each one, I am planning to create 3 VDC, but at the initial configuration the system does not show the ethernets ports of these modules, even with the show inventory and show module I can see tah the modules are recognized and its status is OK. There is something that I have to do before start to configure these modules...? enable some feature or license in order to see the ports with show running CLI...?

Welcome to the Design and Architecture Community

Welcome to the Network Infrastructure Design and Architecture Community. We encourage everyone to share their knowledge and start conversations on design and overall network topology. All topics are welcome, including requirements and constraints of the network, tools and techniques, issues of hierarchy, leading practices, services, build strategies, architectures and solutions to solve business problems.
Remember, just like in the workplace, be courteous to your fellow forum participants. Please refrain from using disparaging or obscene language or posting advertisements.
Cheers,
Dan BruhnCSC Community Manager

been waiting to see a forum like this. This forum should amalgamate all the other areas like R&S, security, DC design, and provide more quality , proven solns and discuss problems/challenges as well. Will be following this forum regularly
thanks dan for creating this community
Regards Kishore

Welcome to Solutions and Architectures Borderless Networks Community

Welcome to the Solutions and Architectures Borderless Networks Community. We encourage everyone to share their knowledge and start conversations related to Borderless Solutions and architectures. All topics are welcome, including Switches, Routers, Security, Wireless, Cloud and System Management, WAN Optimization and solutions to solve business problems.
Remember, just like in the workplace, be courteous to your fellow forum participants. Please refrain from using disparaging or obscene language or posting advertisements.
Cheers,
Dan Bruhn

Hi,
I have a question...
I going to install two Nexus 7009 with three N7K-F248XP-25 modules on each one, I am planning to create 3 VDC, but at the initial configuration the system does not show the ethernets ports of these modules, even with the show inventory and show module I can see tah the modules are recognized and its status is OK. There is something that I have to do before start to configure these modules...? enable some feature or license in order to see the ports with show running CLI...?

Welcome to the Solutions and Architectures Collaboration Community

Welcome to the Solutions and Architectures Collaboration Community. We encourage everyone to share their knowledge and start conversations related to Collaboration Solutions and architectures.All topics are welcome, including Collaboration Applications, Customer Collaboration, Telepresence, Unified Communications and solutions to solve business problems.
Remember, just like in the workplace, be courteous to your fellow forum participants. Please refrain from using disparaging or obscene language or posting advertisements.
Cheers,
Dan Bruhn

Hi,
I have a question...
I going to install two Nexus 7009 with three N7K-F248XP-25 modules on each one, I am planning to create 3 VDC, but at the initial configuration the system does not show the ethernets ports of these modules, even with the show inventory and show module I can see tah the modules are recognized and its status is OK. There is something that I have to do before start to configure these modules...? enable some feature or license in order to see the ports with show running CLI...?

Looking for a high-performance and reliable NAS

Hi,
I have been searching for a high-performance and reliable SOHO NAS storage but I have seen very mixed and contradicting reviews for the products I have looked at so far. From QNAP to Synology to etc.
However I've not found a good review for Promise SOHO NAS devices such NSx700 and NSx600.
Is anybody here using them? If so how would you rate these devices?
Thanks in advance,
Behrang

My g/f is using a Synology 1511+ with 2TB WB black drives - set up for 2 disk redundancy.
http://www.synology.com/us/products/DS1511+/index.php
She has her lightroom images on there and it works very well with her MBP 10.6.8
If you have specific questions, please ask
Michael

Performance and Stability Problem with PE9

I just upgraded my computer to a Core i5 with 8G of memory and everything is running much faster. But my NEW PE9 just run very slow. Some of the simple tasks take 10-30 second to complete. Even Windows 7 will often come out to ask if I want to wait for PE9 to wake up or kill the process. When I want to change the size of a video clip, it just doesn't work at all due to performance. It will take PE9 20-30 seconds to resize the video clip. Without some realtime feedback of the size, it is impossible to do the resizing and this is a very fundamental operation. PE9 often crash or seize up as well, I didn't have any of these problem with PE3.0. I upgraded to PE9 simply because my PE3.0 for WIndows XP is not comletely compatible with Windows 7 (some of the text displace does not show up).
Do anyone else have issue with performance and stability?

Some general comments, and reading (some for PPro, but concepts are the same)
http://forums.adobe.com/thread/416679
Some specific information that is needed...
Brand/Model Computer (or Brand/Model Motherboard if self-built)
How much system memory you have installed, such as 2Gig or ???
Operating System version, such as Win7 64bit Pro... or whatevevr
-including your security settings, such as are YOU the Administrator
-and have you tried to RIGHT click the program Icon and then select
-the Run as Administrator option (for Windows, not sure about Mac)
Your Firewall settings and brand of anti-virus are you running
Brand/Model graphics card, sush as ATI "xxxx" or nVidia "xxxx"
-or the brand/model graphics chip if on the motherboard
-and the exact driver version for the above graphics card/chip
-and how much video memory you have on your graphics card
Brand/Model sound card, or sound "chip" name on Motherboard
-and the exact driver version for the above sound card/chip
Size(s) and configuration of your hard drive(s)... example below
-and how much FREE space is available on each drive (in Windows
-you RIGHT click the drive letter while using Windows Explorer
-and then select the Properties option to see used/free space)
While in Properties, be sure you have drive indexing set OFF
-for the drive, and for all directories, to improve performance
My 3 hard drives are configured as... (WD = Western Digital)
1 - 320G WD Win7 64bit Pro and all programs
2 - 320G WD Win7 swap file and video projects
3 - 1T WD all video files... read and write
Make sure you have the default Windows hard drive indexing set to OFF for all hard drives and folders
Some/Much of the above are available by going to the Windows
Control Panel and then the Hardware option (Win7 option name)
OR Control Panel--System--Hardware Tab--Device Manager for WinXP
Plus Video-Specific Information http://forums.adobe.com/thread/459220?tstart=0
And, finally, the EXACT type and size of file that is causing you problems
-for pictures, that includes the camera used and the pixel dimensions
Read Bill Hunt on a file type as WRAPPER http://forums.adobe.com/thread/440037?tstart=0
What is a CODEC... a Primer http://forums.adobe.com/thread/546811?tstart=0
What CODEC is INSIDE that file? http://forums.adobe.com/thread/440037?tstart=0
For PC http://www.headbands.com/gspot/ or http://mediainfo.sourceforge.net/en
This is aimed at Premiere Pro, but may help
Work through all of the steps (ideas) listed at http://forums.adobe.com/thread/459220?tstart=0
If your problem isn't fixed after you follow all of the steps, report back with ALL OF THE DETAILS asked for in the FINALLY section at the troubleshooting link
Also, tuning Win7
http://www.pcworld.com/businesscenter/article/220753/windows_7_godmode_tips_tricks_tweaks. html
Temp/Cookie Cleaner http://www.mixesoft.com/
http://forums.adobe.com/thread/789809?tstart=0
Win7 Toolbar http://WindowsSecrets.com/comp/110210
More Win7 Tips http://windowssecrets.com/comp/110127
Utilities http://windowssecrets.com/comp/110106 (Startup Solutions)
Win7 Help http://social.technet.microsoft.com/Forums/en-US/category/w7itpro/
Win7 Configuration Article http://windowssecrets.com:80/comp/100218
Win7 Monitor http://windowssecrets.com:80/comp/100304
Win7 Optimizing http://www.blackviper.com/Windows_7/servicecfg.htm
Win7 Virtual XP http://www.microsoft.com/windows/virtual-pc/
More on Virtual XP http://blogs.zdnet.com/microsoft/?p=5607&tag=col1;post-5607
Win7 Adobe Notes http://kb2.adobe.com/cps/508/cpsid_50853.html#tech
Win7 Adobe Update Server Problem http://forums.adobe.com/thread/586346?tstart=0
An Adobe Win7 FAQ http://forums.adobe.com/thread/511916?tstart=0
More Win7 Tips/FAQ http://forums.adobe.com/thread/513640?tstart=0
Processes http://technet.microsoft.com/en-us/sysinternals/bb896653.aspx
Compatibility http://www.microsoft.com/windows/compatibility/windows-7/en-us/Default.aspx
Win7 God Mode http://forums.adobe.com/thread/595255?tstart=0
CS5 Install Error http://forums.adobe.com/thread/629281?tstart=0
CS5 Help Problem http://kb2.adobe.com/cps/842/cpsid_84215.html
Win7 and Firewire http://forums.adobe.com/thread/521842?tstart=0
http://lifehacker.com/5634978/top-10-things-to-do-with-a-new-windows-7-system
http://www.downloadsquad.com/2009/05/29/7-free-windows-7-tweaking-utilities/
Win7 64bit Crashing and "a" fix http://forums.adobe.com/thread/580435?tstart=0
http://prodesigntools.com/if-any-problems-downloading-or-installing-cs5.html
Harm's Tools http://forums.adobe.com/thread/504907
Also http://www.tune-up.com/products/tuneup-utilities/
Also http://personal.inet.fi/business/toniarts/ecleane.htm

BEA / Wily: Financial Webinar - Achieving Availability, Performance and Control of Java Applications in Financial Services

Event Date: October 1, 2002 at 11:00 AM Pacific (US), 02:00 PM Eastern (US)
To register: http://regsvc.placeware.com/?wily-bea1001
Title: Achieving Availability, Performance and Control of Java Applications
in Financial Services
Abstract:
In today's competitive environment, financial institutions must focus on
three key business goals:
a.. Creating a customer-centric enterprise to maximize value to customers
and increase share of wallet
b.. Improving transactional efficiency for rapid delivery of the right
products, services and information to customers and to employees
c.. Accelerating the decision making process to mitigate risk and improve
returns.
BEA and Wily Technology have helped a number of financial services firms
meet these objectives by delivering high-performance business solutions that
meet rigorous demands for performance, reliability and scalability.
On October 1, 2002, Wily Technology and BEA will present a joint Web seminar
titled "Achieving Availability, Performance and Control of Java Applications
in Financial Services" with Eric Gudgion, Principal System Architect,
Technical Solutions Group at BEA and Chris Farrell, Director of Technical
Marketing at Wily. This Webinar will showcase the many advantages that the
WebLogic® Enterprise PlatformT and Wily's Introscope® offer financial
services firms.
Attendees will learn how WebLogic Server, BEA's unified, simplified and
extensible solution, provides a robust platform for the development and
deployment of enterprise Java applications. Some examples of what financial
institutions can achieve with BEA include Multi-channel Services Delivery,
Straight-Through Processing, Wealth Management and Cash Management.
Wily Technology will highlight Introscope's ability to manage financial
services Java applications by pinpointing component-level performance issues
in real-time, whether in the application, application server or
Java-connected back-end systems. Wily's suite of Java application management
solutions offers a comprehensive platform for achieving 24x7 application
availability, enhanced performance and better control of IT resources.

First of all you should check out which products are supported on 64bit :- http://www.oracle.com/technology/products/bi/hyperion-supported-platforms.html
If you are planning on using windows 64bit EAS then you will have to manually deploy the web application, it cannot be automatically deployed.
Cheers
John
http://john-goodwin.blogspot.com/

Is there a way to view Flash videos on my iMac without downloading Adobe Flash Player? I'm concerned about performance and security with Flash Player.

Is there a way to view Flash videos on my iMac without downloading Adobe Flash Player? I'm concerned about performance and security with Adobe Flash Player.

If the video is only available in a format that requires Flash player : then no.
However, a great many can also be viewed in an HTML5 version, in which case http://hoyois.github.io/safariextensions/clicktoplugin/ or similar can be set up so that Flash never runs unless you specifically choose it to.

FAQ's, intros and memorable discussions in the Performance and Tuning Forum

Welcome to the SDN ABAP Performance and Tuning Forum!
In addition to release dependent information avalaible by:
- pressing the F1 key on an ABAP statement,
- or searching for them in transaction ABAPDOCU,
- using the [SDN ABAP Development Forum Search|https://www.sdn.sap.com/irj/sdn/directforumsearch?threadid=&q=&objid=c42&daterange=all&numresults=15&rankby=10001],
- the information accessible via the [SDN ABAP Main Wiki|https://wiki.sdn.sap.com/wiki/display/ABAP],
- the [SAP Service Marketplace|http://service.sap.com] and see [SAP Note 192194|https://service.sap.com/sap/support/notes/192194] for search tips,
- the 3 part [How to write guru ABAP code series|https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/f2dac69e-0e01-0010-e2b6-81c1e8e5ce50] ... (use the search to easily find the other 2 documents...)
... this "sticky post" lists some threads from the ABAP forums as:
- An introduction for new members / visitors on topics discussed in threads,
- An introduction to how the forums are used and the quality expected,
- A collection of some threads which provided usefull answers to questions which are frequently asked, and,
- A collection of some memorable threads if you feel like reading some ABAP related material.
The listed threads will be enhanced from time to time. Please feel welcome to post to [this thread|Suggestions thread for ABAP FAQ sticky; to suggest any additional inclusions.
Note: When asking a question in the forum, please also provide sufficient information such that the question can be answered usefully, do not repeat interview-type questions, and once closed please indicate which solution was usefull - to help others who search for it.

ABAP Performance and Tuning
Read Performance => Gurus take over the discussion from Guests caught cheating the points-system.
SELECT INTO TABLE => Initial questions often result in interesting follow-up discussions.
Inner Joins vs For all Entries. => Including infos about system parameters for performance optimization.
Inner Join Vs Database view Vs for all entries => Usefull literature recommended by performance guru YukonKid.
Inner Joins vs For All Entries - performance query => Performance legends unplugged... read the blogs as well.
The ABAP Runtime Trace (SE30) - Quick and Easy => New tricks in old tools. See other blogs by the same author as well.
Skip scan used instead of (better?) range scan => Insider information on how index access works.
DELETE WHERE sample case that i would like to share with you => Experts discussing the deletion of data from internal tables.
Impact of Order of fields in Secondary index => Also discussing order of fields in WHERE-clause
"SELECT SINGLE" vs. "SELECT UP TO 1 ROWS" => Better for performance or semantics?
into corresponding fields of table VERSUS into table => detailed discussion incl. runtime measurements
Indexes making program run slower... => Everything you ever wanted to know about Oracle indexes.
New! Mass reading standard texts (STXH, STXL) => avoiding single calls to READ_TEXT for time-critical processes
New! Next Generation ABAP Runtime Analysis (SAT) => detailed introduction to the successor of SE30
New! Points to note when using FOR ALL ENTRIES => detailed blog on the pitfall(s) a developer might face when using FAE
New! Performance: What is the best way to check if a record exist on a table ? => Hermann's tips on checking existence of a record in a table
Message was edited by: Oxana Noa Zubarev

Performance and Sprite objects

I've written an application in Flex 2 that consists of
several accordions containing custom canvas objects, and it is
having performance problems.
I'm running the application within IE 6.0 under Windows 2000.
The application loads an XML file and uses the data to create
custom Sprite objects in the canvases. Each Sprite consists of two
swf images that are loaded using the Loader class, a small
rectangle created by using the Sprite graphics property, and a text
label. In addition, each Sprite is connected to one or more other
Sprites by a line drawn using the Sprite's graphics property. The
Sprites have the capability for being dragged, and for being
highlighted when clicked.
My problem is performance; these Sprites perform slower than
a similiar program that I wrote in ActionScript 2.0. From what I
understand, Flex 2.0, ActionScript 3.0, Flash 9, and the new Sprite
class are supposed to deliver greatly improved performance, but my
new application seems worse than the old one under Flash 7 using
MovieClips. The more Sprites on the screen, the worse the
performance, and the lines seem to contribute to the degradation.
There is way too much code involved to include in this
message, so I'm looking for general info. Is there some basic point
I am missing?
The performance is also degraded when triggering instances of
the Menu and Popup classes. When running the Task Manager during
the application, I've noticed that both Memory Usage and GDI
objects increase whenever I display a Menu or Popup. Both Memory
Usage and GDI objects go up and down, but there is a steady
increase in both metrics as I continue to use Menus and Popups. As
far as I can tell, I am disposing of both types of objects
properly, but it appears that their allocation is remaining in
memory.

I've written an application in Flex 2 that consists of
several accordions containing custom canvas objects, and it is
having performance problems.
I'm running the application within IE 6.0 under Windows 2000.
The application loads an XML file and uses the data to create
custom Sprite objects in the canvases. Each Sprite consists of two
swf images that are loaded using the Loader class, a small
rectangle created by using the Sprite graphics property, and a text
label. In addition, each Sprite is connected to one or more other
Sprites by a line drawn using the Sprite's graphics property. The
Sprites have the capability for being dragged, and for being
highlighted when clicked.
My problem is performance; these Sprites perform slower than
a similiar program that I wrote in ActionScript 2.0. From what I
understand, Flex 2.0, ActionScript 3.0, Flash 9, and the new Sprite
class are supposed to deliver greatly improved performance, but my
new application seems worse than the old one under Flash 7 using
MovieClips. The more Sprites on the screen, the worse the
performance, and the lines seem to contribute to the degradation.
There is way too much code involved to include in this
message, so I'm looking for general info. Is there some basic point
I am missing?
The performance is also degraded when triggering instances of
the Menu and Popup classes. When running the Task Manager during
the application, I've noticed that both Memory Usage and GDI
objects increase whenever I display a Menu or Popup. Both Memory
Usage and GDI objects go up and down, but there is a steady
increase in both metrics as I continue to use Menus and Popups. As
far as I can tell, I am disposing of both types of objects
properly, but it appears that their allocation is remaining in
memory.

6800 performance and architecture

Similar Messages

Maybe you are looking for