694D Pro compatible with PIII 1GHz ???

have a 694D Pro Ver 1.0 (MS6321) Board.
CPU Support page on the Website says PIII 1GHz is OK.
BUT the table shows it has a 100 MHz FSB which is WRONG! The SLOT1 PIII 1G has a 100 MHZ FSB. The Socket370 PIII 1G has a 133 FSB.
The manual indicates the board is compatible with 133 Mhz FSB processors. The CPU Support page seems to indicate that all the Tualatin series processors are not compatible. It appears that all processors with 133 FSB which have a speed > 1 Ghz are all Tualatins and are not compatible. Is that because of the 133 FSB or something else about the Tualatin series? Will the 1G Coppermine work because it is not Tualatin even though it has a 133 FSB?
My real concern is will the PIII 1GHz 133 MHz FSB work on this board? Is this the fastest CPU that will run (reliably) on this board?
dazed and confused (THANKS FOR YOUR HELP! ) )

Both Slot1 and FCPGA PIII's were available at both 1.0Ghz/133 and 1.0GHz/100. link
A Coppermine PIII 1.0GHz/133 (or two of them that are identical) will work on the 694D.
Tulatin's use 1.5V and have a different BUS specification and pin assignment than Coppermine so a Tulatin won't even post on the 694D.

Similar Messages

TS4498 Is music created in logic pro compatible with the logic pro x ? for instance if you have created something in logic pro and wont to add or tweak it a bit is that possible?

Is music created in logic pro compatible with the logic pro x ? for instance if you have created something in logic pro and want to add or tweak it, is that possible? I suppose you would need the original logic folder?

Yes it is more or less compatible, except the use of 32 bit plugins, which is prohibited from now on. So although you're able to open Logic projects as far as down to v5 I believe, it is advisable to remain for 'adding and tweaking' in your pre LPX environment.
Have a nice day!

Is the late 2013 mac pro compatible with 10.8.5

Is the late 2013 mac pro compatible with 10.8.5

No, except through emulation inside a product such as VirtualBox, Parallels Desktop, or VMware Fusion.
(105011)

Is my mac pro compatible with mountain lion?

Is my mac pro compatible with mountain lion/ 2 x 2.66 Ghz Dual core processors?
Any help would be appreciated. Thanks
William

And FBDIMMs which use to cost $300+ for 8GB can now be had for... 2 x $34.
I paid $300 2 x 512MB August 2006,, then 2 x 1GB $400 March '07
So as long as you only need 16GB you are safe, it is when you need 4GB, or the rare 8GB FBDIMM and 32GB or more, that yes, time to part ways and get a system that supports cheaper DDR3.
Except, right now, 10.8.2 'broke' support for more than 64GB and there were people depending on and using 96GB. Or that more than 48GB also 'broke' the Apple Pro RAID card; a card that still does not support 3TB drives. 10.8.2 does though provide support for more current Nvidia cards (10.7.4 also showed support just not for GTX 6xx series). 3rd party graphic support has always been a weakness, until now.
Apple Mac Pro is a workstation. Except when it is not. It is still not clear how they missed these things.
What 32-bit EFI won't get you is 64-bit kernel mode and abilty to fully use more powerful graphic cards or memory addresses for a single process beyond 4GB or graphic card support with more than 2GB (and 2GB use to always fail in OS X in the past).

Video recorded in QT Pro-compatible with FCP?

Is a video recorded in QT Pro compatible with FCP?
I was getting errors earlier today importing QT video clips recorded in QT Pro.
FCP said "unknown file type" and wouldn't import it.
I tried different decks, different footage, all to no avail.
Drag and drop, file>Import, neither worked.
I never tried this before and was surprised.
It's not that it needed rendering, it just wouldn't import.
QT was set to use the native format of the recording device.
FCP was set to DV NTSC easy set up.
OS 10.4.7, QT 7.1.2, FCP 5.0.4.
Thanks,
Richard

Now this is strange.
I just downloaded Live Capture Plus to try it out.
It captures the same tape from the same deck with the same settings as I tried in QT.
Imports perfectly into FCP 5.1.1 No problems whatsoever.
Both clips have identical settings in the info pane of QT Pro:
DV/DVCPRO - NTSC, 720 x 480 (640 x 480), Millions
16-bit Integer (Big Endian), Stereo (L R), 48.000 kHz
29.97
640 x 480 pixels
Yet the QT clip will not import into FCP with an "unknown file" error.
Why?
Thanks
Richard

694D Pro-AR Dual PIII 1,0 AGP probs?

Hi,
also running WinFast 250 ultra -ti 4600 GF4
When i enables AGP fastwrites in BIOS my system hangs, AGP4 is already enabled but the VGA Card only runs at AGP2x.
I have updated my BIOS to the latest, and running the latest VIA 4in1
How can i get it to run in AGP4x??
Any help is appriceated, thank you
-Chris

I have just received my 694D Pro-AR from RMA. Once I reinstalled all my hardware, now I can't run my ATI All-In-Wonder RADEON in AGP4X and my DVD is choppy (even with my DVD running in Ultra DMA mode).
Also, I can't perform Digital Audio Extraction anymore.
I've reformatted/reinstalled everything anew with all the latest firmware/bios/drivers possible.
Everything was fine before I received my new board (which had blown capacitors on it).
My system also has:
2 PIII 800, 512MB SDRAM
RAID 0 with 2 45 GB harddrives
ATI All in Wonder RADEON
Creative SB Live! Platinum 5.1
Pioneer 16X DVD (105S)
Plextor Plexwriter 12/10/32A
etc...
I suspect there may be a something wrong with the new VIA drivers perhaps?

MacBook Pro compatible with 3G iPod (five-button)????

Any chance that my 3G iPod (the one with four buttons and the wheel) will be compatible with my new MacBook Pro? I'd have to at least buy a Firewire 400 to Firewire 800 converter. But there's no point in buying one if the iPod won't otherwise be compatible.
Your thoughts??

I can't see why it wouldn't be compatible, yes all new iPods and the like are now USB. But that was a move to encompass the world of Windows computers which tend not to have FW ports.
The main problem I see is the iPod cable has a FW400 plug on it so you need a FW400 socket to plug it into. A FW800 to FW400 cable won't be much use as that is just plug to plug. You would then need a FW Hub to plug into so that you can then plug the iPod cable into that. Or if you have something like a like an external FW drive they usually have a couple of sockets on them. So you could use a FW800 to FW400 to connect the drive and then plug the iPod into the drives other FW400 socket.
I did a very quick search but did not come up with a FW800 plug to FW400 socket, they may exist somewhere?
Sorry I can't help further.
Phil

Is New Mac Pro Compatible with Logic X

Im interested in getting the new mac pro. Is this compatible with Logic X plugins does anyone have it yet working with Logic pro. I have a Mac Pro 3.33ghz 6 core. Is this 10 times better or just a little. I already have good SSD drive so loading and streaming samples is lightning fast.
thanks

hi i have another question i don't know if anyone knows. in Logic X when I pen the mixing board the scrolling lags for a second and stutters lags for a couple of movements then it scrolls back and forth normally. but when I shrink the arrange window with the mixer to a smaller size it gets faster as I shrink the screen.
I have a HP 30" monitor hooked up by dual DVI cable. 60hz refresh rate. A GTX-680 2g Video Card.
My friedn has a imac 27" i7. I have a mac pro 3.33ghz 6 core. His mixing board does not lag. also copiny plugins is slow on mine. his did not lag.
is this because my monitor is older and using dvi insted of hdmi or thinderbolt?

Is Roxio Toast Titanium 11 Pro compatible with OS 10.8

Is toast 11 Pro titanium compatible with Mountin Lion

DVD's burn OK from iTunes.
Spin Doctor totally crashes my MAC Mini and it has to do a restart. (Grey screen of death)
More about this on the Roxio forum.
http://forums.support.roxio.com/topic/82763-will-toast-11-pro-work-with-the-new- mac-os-108-mountain-lion/http://

Soundtrack Pro compatible with Final Cut Express?

I have Final Cut Express 4 installed and installed Logic Studio. Soundtrack Pro and Compressor did not install. Are these programs not compatible with FC Express?

From the Apogee website:
"Duet features two superb microphone inputs, each with phantom power and up to 75dB of gain. With Duet, you can record a pristine vocal track while playing your guitar or keyboard, stereo mic your acoustic or even capture a live concert."
http://www.apogeedigital.com/products/duet.php
It's ideal target audience would be laptop users in need of a high-quality, but very portable audio interface for Logic.
Message was edited by: lwilliam

Are Distributed Forms created in Acrobat XI Pro compatible with Response Forms in Acrobat X Pro?

I want to be able to use distributed forms (created in Acrobat XI Pro) that I have received back through email with Acrobat X Pro. That is, I want to be able to import the form information that is being sent back to me into a response form in Acrobat X Pro. Is this kind of "forward-compatible" issue possible?
Or, since I created the distributed forms in Acrobat XI Pro, can I only import data from those forms in an appropriate response from in Acrobat XI Pro?
Thanks!

The distribution technique for email, network folder, or internal server haven't changed between Acrobat X and XI so you should be able to do this; however, it won't be managed through Tracker because you're distributing the form through different programs.

Is Logic Pro compatible with Roland REAC technology?

My church is considering purchasing a new Roland m200i and they only list support for direct recording to Cakewalk Sonar (not Mac compatible). Has anyone set up logic pro (or any other DAW) to work with a direct Roland REAC connection?

REAC requires a driver to be installed on the computer, the drivers are PC compatible only.

How can I make Acrobat 6 Pro compatible with Windows 7?

When I load Acrobat 6 Pro on my Windows 7 laptop I get a message stating it isn't compatible. Is there a fix for this issue?

If you were able to install it with Acrobat and Distiller opening if selected, there is a chance. However, it is a work around. The problem is typically the print driver and Acrotray. The work around (if these two basic programs run) is to install a color PS printer (may be one of the HP printers or even a PS printer from Adobe), rename it to Adobe PDF, and set the port to FILE. To print or use PDF Maker, you print to this Adobe PDF printer that you have created. Then open the file created in Distiller to obtain a PDF. I have done this with AA7 on a WIn7, 64-bit, and with AA5 (naming the printer Acrobat Distiller) on Win7, 32-bit, for testing.
Also, be sure to install the updates to Acrobat. You will likely have to download them from http://www.adobe.com/support/downloads/product.jsp?product=1&platform=Windows and install them in order.

Is my mid 2010 macbook pro compatible with apple tv?

I just purchased apple tv and am having trouble with airplay are mirroring? I need to know if my mid 2010 macbook pro and ipad 2 are compatiable? Because so far the only thing i am able to get on my apple tv is my music. I am unable to mirror any of my pics or applications.
Help please!!

It has a newer processor that is capable of video encoding.
AirPlay Mirroring in OS X takes advantage of the hardware video encoding capabilities of 2nd and 3rd Generation Intel Core processors. Hardware video encoding allows AirPlay Mirroring to efficiently deliver high frame rates while maintaining optimal system performance.
http://support.apple.com/kb/ht5404

Is Print Studio Pro Compatible with Photoshop CC 2014

I recently acquired a Pixima Pro 100 and am attempting to install Print Studio Pro so that it can be accessed in Photoshop CC 2014. When I attempt to install, it will find and install in Lightroom and Photoshop CC. However, it does not find and install in Photoshop CC 2014. I have attempted to uninstall Photoshop CC with the hope that it would find Photoshop CC 2014. But it does not. Does any know how to install Print Studio Pro so that it will find Photoshop CC 2014? Cheers, Don Barar

Hi Debra, Thanks for writing. What I have learned is that Print Studio Pro is not set up to recognized Photoshop CC (2014). I happened to have still retained Photoshop CC in my computer. The installer did recognize Photoshop CC and was installed. In another forum, a user suggested that I copy the plug-in Print Studio Pro from Photoshop CC to the plug-in directory on Photoshopy CC (2014). That worked. Now I have access to Print Studio Pro in Photoshop CC 2014. Cheers, Don Barar

694D Pro compatible with PIII 1GHz ???

Similar Messages

Maybe you are looking for