694D Pro2 with Geforce4 ti4600

hi there!
Can anyone tell me if anybody had experienced any problem using a Geforce4 ti4600 in 694D Pro2 MS-6321 with dual 1Ghz 133mhz cpu.
I have upgraded from MSI Geforce3 to Asus Geforce4 ti4600 ultra deluxe and during the POST, I see 12 white blocks on the screen and then on the win2k startup there are 12 blue blocks afterwards the system hangup.
I have asked for a Geforce4 replacement and my dealer told me that I have to make sure that MSI is compatible with the new VGA card.
Is this possible? I do not have any problem with my old Geforce 3 which is almost the same as with Geforce4.
Help needed before I put the new board in. ?(
Aeigis

First, make shure you have a good and strong power supply. GeForce 4 tends to draw a lot of power. Adding two 1 GHz CPUs, although Intel P-III, doesn't make the burden easier... I wouldn't go for anything less than 300 W, and preferably 340 W or even more. Also be aware that not all so called 300 W PSU's are equally strong. Chieftec makes good PSU's, I would probably recomend their 340 W for this system, unless you have many hard disks or CD's, in which case I would choose an even more powerful PSU.
If possible, you should also test the graphics card in another computer, just make shure the PSU is strong enough for the GF4.
Best regards
Quote
Originally posted by aeigis
hi there!
Can anyone tell me if anybody had experienced any problem using a Geforce4 ti4600 in 694D Pro2 MS-6321 with dual 1Ghz 133mhz cpu.
I have upgraded from MSI Geforce3 to Asus Geforce4 ti4600 ultra deluxe and during the POST, I see 12 white blocks on the screen and then on the win2k startup there are 12 blue blocks afterwards the system hangup.
I have asked for a Geforce4 replacement and my dealer told me that I have to make sure that MSI is compatible with the new VGA card.
Is this possible? I do not have any problem with my old Geforce 3 which is almost the same as with Geforce4.
Help needed before I put the new board in. ?(
Aeigis

Similar Messages

Problem with Geforce4 Ti4600 AGP4X

well I tried searching the forums but I couldn't find a thread that pertained to my problem :/, so: I have the MSI Geforce4-Ti4600 AGP4X card, but when I use it I see lines running down my monitor. The picture is still there (sometimes), but there are vivid lines of color that run vertically on the screen maybe a centimeter wide. So right now I'm using my GF2 ULTRA, but I was thinking that if I couldn't get any help on here I'd go ahead and return the card on warranty...and by the way could someone explain to me how that works? Thanks for any help.
-Josh

First, make shure you have a good and strong power supply. GeForce 4 tends to draw a lot of power. Adding two 1 GHz CPUs, although Intel P-III, doesn't make the burden easier... I wouldn't go for anything less than 300 W, and preferably 340 W or even more. Also be aware that not all so called 300 W PSU's are equally strong. Chieftec makes good PSU's, I would probably recomend their 340 W for this system, unless you have many hard disks or CD's, in which case I would choose an even more powerful PSU.
If possible, you should also test the graphics card in another computer, just make shure the PSU is strong enough for the GF4.
Best regards
Quote
Originally posted by aeigis
hi there!
Can anyone tell me if anybody had experienced any problem using a Geforce4 ti4600 in 694D Pro2 MS-6321 with dual 1Ghz 133mhz cpu.
I have upgraded from MSI Geforce3 to Asus Geforce4 ti4600 ultra deluxe and during the POST, I see 12 white blocks on the screen and then on the win2k startup there are 12 blue blocks afterwards the system hangup.
I have asked for a Geforce4 replacement and my dealer told me that I have to make sure that MSI is compatible with the new VGA card.
Is this possible? I do not have any problem with my old Geforce 3 which is almost the same as with Geforce4.
Help needed before I put the new board in. ?(
Aeigis

MSI-6321 694D Pro2 wont boot past RAID

Hi,
I have a 694d pro2 with dual P3 933's. The board has been running fine with Windows 2000 Server. The problem I have is that now when it boots, it reaches the onboard RAID configuration then halts. I'm not running any array's nor am I using the controller as a standard IDE controller.
Any ideas?
Thanks!

Does it halt 'after' detecting the drives connected to the RAID array or before-hand ?
If its halting afterwards you may want to try specifying a different boot order in the BIOS. Maybe its looking for a boot condition or component that isn't responding correctly.
When it halts does the system still respond to a CTRL + ALT + DELETE, or do you need to power it off from holding the button down for 4 seconds ?? If its a soft boot then the system 'is' still responding but is just paused. Needing to hard boot it would probably mean its something a little more serious.
I had a slightly similar problem with an IDE ZIP drive hooked up to the onboard (northbridge) IDE connecters on a 6321. No matter what boot order I had the system in it wouldn't get past the onboard promise card. In the end I switched ZIP drive to an A: drive, and swapped the onboard floppy over to the B: drive and vwala .. system happy.
Hope this helps.

Help with 694D Pro2 & PIII 1133 Copermine

I have 694D Pro2 MS-6321
It good work with PIII 800.
But it can't boot with PIII 1133.
Label on CPU:
INTEL ... 1133/256/133/1.475
7220A844-1004
PENTIUM III SL5LT
BIOS ver 5.2
There are all 4 lamps light red.
Help me, please

http://www.msi.com.tw/program/support/cpu_support/cpu/spt_cpu_detail.php?UID=84%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20&NAME=MS-6321%20Ver2.0
is it a Tualatin version?

Geforce4 ti4600 conflicting or something with win2k.

Hi all...just got me brand new K7N2 Delta-ILSR....I got it all plugged in and went to install win2k pro...it gets through the dos portion of the setup with no problem...I'm not installing the raid drivers because my HDD's are not on the raid controller.
It gets done copying and says its goign to reboot to finish the install...it does so...then when it comes back up I get the dos-like progress indicator at the bottom of the screen that says Starting Windows and it goes all the way across and then the screen goes blank and stays that way...
I've tried numerous things and managed to narrow it down to the video card...I put in an old PCI card and it worked fine...I've pulled out all my other cards and extra devices and turned off the on board extras.
Apparently I'm missing some particular bios setting perhaps that makes my video card work properly?
I have the following actually plugged in:
Antec 450 Watt PSU
K7N2 Delta-ILSR
AMD Athlon XP 3000+ (333 version)
Crucial PC3200 512Mb
Visiontek Geforce4 ti4600
Anybody got any bright ideas???

I'm pretty sure I tried that already, along with increasign the voltage to it.

Help!! VGA Ti-4200-VTDX8 (MS-8894) and MB 694D Pro2(MS 6321)?

I have upgraded my VGA with Ti4200-VTD8X (MS-8894) VGA. I'm having trouble getting the VGA to 4x AGP. I have tried changing settings in bios etc, but it ALWAYS run at 2x AGP. My MB 694D Pro2(MS 6321) should work fine at 4x AGP i've been told.
Any suggestions what i can do? Settings in bios/VGA etc?
Tom
Post #2
VGA Ti4200-VTD8X MS 8894 Intervideo
The software intervideo Winproduser delivred with my VGA board promised MPEG4 video format transferring.
How do i get that to work?`
I'm using Video 8 camera analog. When i import the video i get poor quality what ever option i use importing it. I've tried all option's including AVI, mpeg setting in nVida WDM video capture (universale).
Any suggestions how i can get better quality?
Tom
Post #3
nVida GF4 Ti4200 problem
When i enable AGP Fast Write in bios, PC lock up wile XP is starting.
How can i fix this, and do i loose a lot power when this funktion is disabled?
Tom
MB MB 694D Pro2(MS 6321)
CPU 2 x PIII 800
VGA Ti4200-VTD8X (MS-8894)
HD Western digital x 4
DVD Creative 12x
RAM 1GB (4x 256 SD-RAM)
CD-RW Lite on 40x12x40
Tower Chiftek midi
OS Windows XP 2600 Service pack 1
[I put all your posts into this one since no one will get the Big Picture of your probles if each one is in a different thread scattered all over this forum. - Richard]

Thank you, but I've already tried that kind of stuff :/
I tried changing my onboard network card from automatic to 10 mpbs half duplex... And it changed the performance alot, now it hardly never lags, but when it lags, it's for like 3 seconds.
The weird thing is that when it lags, it's only movement - I can shoot while it's stuck (weird).

MSI GeForce4 Ti4600-VT2D8X advice?

MSI GeForce4 Ti4600-TD8X 128MB,
MSI GeForce4 Ti4600-VT2D8X
MSI GeForce 4 Ti4200-VTD8X
What's really the difference?
I'm trying to figure out which of these cards to get.
I'll be using it with 3DSMAX for open gl.
and video input /output for various projects.. I'll need at least 704x 480 resolution at real time playback/capture.
Has anyone tried using this card with these?
3dsmax
Maya
Premiere
Combustion
Avid
Any advice or info would be greatly appreciated
Waqas
[email protected]

Quote
When I just touch the video card a little with the power off (without removing at all), it gets back normal when I restart...
The pins on the monitor cable maybe bent. Can you try another monitor.
Could be something loose somewhere on card maybe? Bad solder somewhere etc. When card warms up it can lose connection.
What are the Power Supplies. Can be the root of alot of problems exp with Gf4 (make and wattage of PSU can be the difference of it working or not)
Bluesky. I'm not familier with grounded AC plug. Does this have three wires, or is it a separate wire???

694D Pro2(-IR?) How big HD does this support?

I got a 694D Pro2 motherboard, and I wounder how big hard disk this supports. I thinking about a western digital 8mb cach 120GB, 160GB or 200GB disk.
I also wounder why I got a message that says:
"WARNING! CPU has been changed"
"Please Enter CPU Speed CMOS Setup and Remember to Save Before Exit!"
This message has always comed up since I bought the motherboard, and if i fix it in the bios, it would be the same after I power off my computer. The computer works fine still with this message, but I havto press F1 every time I sould boot my computer.
Odbjørn Bakke
Norway

Here's your answer to the HDD support Qns, you've to go into HDD Support link in this page.
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=84
Next, the speed indication for the CPU is being changed in Softmenu BIOS, but don't worry, it will not do damage to your system. All you've to do is to know what CPU you are running on now, i.e, Dual Intel Pentium III 800 CPU @ 100MHz, then you've to selected this indication from the list in your BIOS. I've had encounter this similar problem on my friend's old P3 running on his ASUS mobo and it's only indication error.
All the Best... :D!!!

Is agp 8x card safe on 694D Pro2?

My 694D Pro2 supports 3.3v agp graphic cards (believe this is agp 2x cards).
I am currently using a agp 4x card (1,5v).
I will like to istall a new 3D card but have read somewhere that a 0,8v (agp 8x) card always can handle the 1,5v but not the 3.3v of older agp slots.
I would like to know if I risk damaging a agp 8x card(0,8v) with 3.3v when using it in my 694D Pro2 mainboard?

Most of the time the card won't fit if it can't be used.
But beware of the universal AGP slots, they can only do 5V if I'm not mistaken.
The slot should have blocking points to stop you from putting wrong cards in.
However the first AGP slots don't have this!!!!
But as you are using an AGP4x card in the board, an AGP 8x card should work well too.

694D Pro2

Hi guys,
I would like to check if this processor, Pentium III 800MHz (SL4MB) is compatible with the 694D Pro2 motherboard. The processor seems to be in PPGA packaging.
Thanx in advance.
Cheers,
Eugene Soh

http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support_detail.php?UID=84&kind=1
YES

Problems booting into OS 9.1 after upgrading to Geforce4 Ti4600

Help!
I still use a older g4 mac to work with several older legacy hardware products such as 12x9 Walcom Tablet, Kodak 8650 dye-sub printer, and a Agfa 12x18 2000xl oversized scanner, and a Nikon LS-2000 neg scanner. So, I still use classic for these hardware items in which os x drivers were never created.
I wanted to use two displays for color proofing, the adc 23" studio display and a DVI formac display. So I needed to upgrade my Geforce2 MX to Geforce4 Ti4600.
It boots fine into OS X however it freezes when booting into os 9.1.
I cannot find any information on the extentions needed for OS 9.1. I am using Nvida drivers 1.1.1 from June 2001. I think this is the source of the problem.
What drivers do I need for the computer to boot?
Adrian

Thank you for the reply, but that link does not work. Is this an os 9.1 issue were the drivers do not exist and I have to upgrade to 9.2.2 or is this an updated drivers issue?
Adrian t

K7N2G-LISR & VisionTek Geforce4 TI4600

Greetings all.
I'm havin' a problem with FPS in games. The video skips pretty badly. It seems to skip about 5 frames every second.
Specs & Settings:
Proc: AMD XP2000+
-FSB 133
Mobo: k7n2g-LISR
-Bios: v1.2
-8x AGP disabled
RAM: Kingston 1024 megs PC3200 DDR
Video: VisionTek GeForce4 Ti4600 (4x version)
-nVidia v43.45 Detonator drivers
OpSys: Windows 2000 Pro (also used Windows XP SP1)
-Service Pack 3 installed
-All windows updates installed

Where would one turn that off? I checked both in the game and in display properties.
Edit - NM found it. nVidia hid it. That didn't work either.

GeForce4 Ti4600 HELP PLZ!!!

Hello all, I have a P4 1.9, Motherboard intel D850MV, 512MB Rambus memory, sb live 5.1, and now i try to install a GeForce4 Ti4600. Whem I start the computer and try to get in in bios setup for exemple, it just turno off the monitor, whem start appear the Intem Pentium 4 logo, after that whem the windows gonna start the monitor just turn off, like on the sleep mode. So i put the card on my brother computer, is a P4 1.4, motherboard intel D850DB, 256MB rambus memory and work perfect. So I ask for the teachers ehehe.. what is the problem? I really think that is the motherboard. :(

Quote
Originally posted by isidro
Hi, i dont know that have a 4pin with 12v on the psu, so i connect that on motherboard and its look that work normally...
You have a 1.9GHz P4. This processor draws more power than was originally planned for ATX 2.0 power supply units (PSUs). Thus, P4-compatible power supplies have been augmented with an additional 12V connector to supply additional current to the motherboard (which then divides and regulates it down to what the processor and other board components expect). Thus, the board/processor/RAM combination generally isn't receiving adequate power to operate when the additional 4-pin connector is not connected.
Quote
and whem i put over that 4pin dont work. Like without the 4pin dont get in on BIOS, and with that get in on BIOS what you think?
Yup. When the extra connector is disconnected, inadequate power is provided and the board does not operate. When it is connected, there is adequate power.
Note that it is still possible to have a too tiny power supply and too power-hungry components. In fact, your particular set of hardware is rather power-hungry. Even if you don't have immediate power trouble, as the power supply ( and other components ) age(s), you may find that the machine is unstable when it is either cold or hot. Eventually this will worsen until either it only works after it's been off for a while or it only works after it's been on for a while.
Thus, although you aren't experiencing power supply trouble currently, it would be wise to watch for the symptoms I've mentioned and then take corrective power supply action if you observe them.
-- Eric Towers ! [email protected]

Major GeForce4:ti4600 problem

Hey everyone, I just bought the MSI Geforce4:ti4600 "champion Edition" video card and i have a huge problem. I uninstalled the drivers from the old video card i was using. and shutdown to install the new card. i installed it and boot up. when i got to the windows 2k screen i get alot of nasty artifact blocks with static going through some of them. i've read through a few threads about this problem but no one seemed to know the answer to the problem.
after i installed the drivers i figured it would be fine after that. was i wrong. it still gave me the same nasty blocks everywhere and it would not even go past the windows 2k start up screen. it would just give me a blue screen of death very quickly and restart. i looked in the BIOS to see if everything was fine and it was. here are my system specs: Abit KG7 mobo
AMD Athlon XP2000+
256mb 2100DDR micron ram
sound blaster x-gamer 5.1
10/100tb nic
windows 2k sp4
350W PSU
+3.3V 14A
+5V
+12V
+5VSB
hope you guys can help, thanks!

Well i just bought a new PSU for my PC and I'm still having the same problems with the video card. X( I think it's time to call MSI for an RMA. this sucks. i was hoping i would not have to do that. now i have to wait til after i move out next week to replace the card. this is my first time upgrading my vid card in over 2 years and i end up with a lemon. :(
well here are the new PSU specs.
3.3v= 28A---\_____220W
5v= 30A-----/
12v= 15A

G4 733 with GeForce4 MX 32MB - second monitor

G4 733 with GeForce4 MX 32MB
I currently run a LaCie Photon 19 at 1280x1024 and am thinking about getting a second monitor to increase desktop space.
My understanding is that the card will support dual monitors at up to 1920x1200. Is that correct, please?
Thanks,
Michael

That's for the GeForce4 MX 64MB, mine is GeForce4 MX 32MB and therein lies the uncertainty.
What does the System Profiler report for the VRAM of the card?
I have a Geforce4 MX from a Quicksilver, and as far as I know, the Geforce4 MX in the QS series are all 64MB VRAM.
Does the card have DVI and ADC or VGA and ADC ports?
I bought this Quicksilver used some years back and it appears the original owner had specified/installed the GeForce4 MX 32MB card which I believe was available as an option on some G4s later than the 733.
If the card came from a MDD, then it would be the Geforce4 MX 32MB card.
http://support.apple.com/kb/SP63
I did find one spec which suggested it would support dual monitors as in my OP but it was not wholly clear.
PC or Mac, the Geforce4 series all support dual displays.
Does the existence of a second display slot in System Profiler indicate dual monitor capability or is it always there regardless of card?
If dual displays were not supported, the System profiler would indicate that.
As you can see from the MDD technical specs page linked above, dual displays are supported.

694D Pro2 with Geforce4 ti4600

Similar Messages

Maybe you are looking for