7.1-7900 Speaker setup problem

I have just set up the speaker system on my new mesh pc but cannot get any sound from two speakers, the left and right side. I have used the THX cosole to test the speakers but nothing happens from these two. I have checked everything is connected correctly, but I think I am missing something obvious. I also have a SB X-FI XTREME sound card. I would be grateful for any help as I am no expert.

Oh...
check with you are u playing song from dvd-audio?
well i am using dvd-audio (96khz, 24bits and 6 ch)song to play back than i need to set your setting as mention than works for 7.
how abt other sound encoding like mp3..
Oh one more thing you need to take note......
is about the S750 tweeter... open up the custion (front casing) check the silver colour tweeter..., make sure is not pressed in should be round and smooth
Check the post that i have mention abt the tweeter:
http://forums.creative.com/creativelabs/board/message?board.id=speakers&message.id=4360#M4360
Else if there the tweeter looks as someone have press on it.. get it replace when still in warrenty.. since most products carry warreny do monthly check of the tweeter if needed.. tell you what tweeter being compress (look like someone have press on it) cannot escape even you buy B&W speaker which cost few K for 2 pair of speaker.
hope it helpsMessage Edited by Blacknight24 on 05--2006 05:6 AM

Similar Messages

Not able to select speaker setup in creative audio cons

Hi, I'm using Creative X-FI Music. Due to a recent re-installation to Vista, after re-installation of drivers and software (with updates from creative support website), I'm still not able to select the speaker setup directly from the audio console. This has prevent me from calibrating my 5. speaker setu
ps.
Please help? Thanks....

what's your os? if you have xp, you should try sp2...that fixed the problems i was having with my card when i upgraded...try telling windows to go to 5. sound through the sound devices in control panel and then go back to surrmixer and see if that works...

Speaker output problems with X-Fi XtremeMu

Today, I bought an X-Fi XtremeMusic card because I was sick of trying to coax my onboard audio to work. I own a set of Logitech Z-5500Ds, and the rear and centre speakers were gathering more and more dust, while my onboard sound refused to work. I should add, my onboard sound did work for a few weeks, but stopped working after what I assume was me installing something that conflicted with it. Anyway, enough about that. I purchased the X-Fi XtremeMusic in the hopes that it would resolve my problems.
Before doing anything, I disabled my onboard audio in the BIOS. After this, I put the card in my computer and installed all the SB X-Fi software and drivers. I restarted, as directed, and when I logged on into my account, The Creative speaker set-up greeted me. I went through the process of selecting my speaker setup (5.) and testing the channels. Left and Right channels worked perfectly, which was expected. When I tested the Rear Left and Rear Right speakers, however, the sound came from the Left and Right speakers, respecti'vely. Moving on to the the Center/Sub test, I was even more disappointed when the Center sound came out of the Left, Right AND Center speakers, and the Sub sound came out as a quiet white noise from both the Left and Right speakers. Now this is EXACTLY what was happening before I bought the card, and I really don't know what to do.
I really want to resolve this issue, so I ask for anyone's help. As of now, I've uninstalled all the drivers and software from Creative, and ready for any advice I'm given.
Thanks
EDIT: I should also add that I'm POSITIVE that everything is plugged in correctly, and that my Rear and Center speakers, as well as my sub work, because I've hooked up my speakers to my Xbox via Optical, and they all work perfectly.Message Edited by FlamingNinja on 07-06-2006 05:28 AM

OK, I had a go at installing the drivers again. Here's the deal. In the speaker setup, the same as before is happening. I ignored this, and continued through the setup. To see if it would even output any sound to my rear speakers, I opened up the Entertainment Window and activated CMSS-3D, and moved it to 50%. Sure enough, it outputs sound to my rear speakers. Can anyone suggest why the test doesn't work though?
I'll try testing a 5. DVD tomorrow and seeing what happens. I'm really hoping the speaker setup is in the wrong.Message Edited by FlamingNinja on 07-06-2006 07:46 AM

Two speaker setup, Audio is strange please he

It appears that my speaker setup has some how gotten corrupted, as my bass only shoots out of one speaker and the audio for both the left and right channel only kicks out of the other speaker. Seeing as my speaker setup up is only a two speaker setup I would like the bass and audio to be coming out of both speakers as it was originally. I've checked and my speaker setup is set to two stereo desktop speakers so I don't know what I should do. Any help is greatly appreciated. Thank you in advance. My cpu is running a Sound Blaster Li've card.
.Sandro.Message Edited by Sandroace on 09-8-200709:3 PM

nycron
That said, the laptop speakers are playing stereo.
Hello. that would suggest that the integrated audio system is working okay and that the problem is in the jack or external device. There is no processing that I know of that would send 2 channels to the speakers but combine them into one channel into the jack.
If you want to replace the jack you would replace this I/O circuit board.
For a workaround there are many inexpensive usb audio jacks available.
If you want to test some more, switch to the Windows native audio driver.
1. Open the Device Manager (type devmgmt.msc in the Windows search box).
2. Expand the "Sound, video & game controllers" and right click on "IDT High Definition Audio Codec".
3. Select to "Update Driver Software".
4. Click on "Browse my computer for driver software".
5. Click "Let me pick from a list of drivers on my computer".
6. Put a check in the box "Show compatible hardware" if not already checked.
7. In the list of devices, click "High Definition Audio" (the native driver).
8. Click "Next".
9. On the Update Driver Warning box, click "Yes" (install the driver).
10. Restart the laptop if prompted. If not prompted, then no need to restart.
[To get back to the IDT driver, do it again but reverse the names in steps 1 and 6.]
If it doesn't work with the native driver then it is pretty surely hardware failure.
nycron
Also, the balance feature in settings is working and allows me to selectively control the volume of the two external speakers.Which suggests it's how sound files is being processed rather than the output jack itself.
If you still feel that it is a software issue could perform a system recovery. Doing so will fix the issue unless it is due to hardware failure.

X-fi speaker setup HELP!

OK i have a quick problem, How in WINDOWS XP do i access this speaker setup page (pictured is windows vista obviously)?http://pws.prserv.net/tpham/pic3.jpg?The reason i ask is i would like to run a true 3. setup with my new Xtrememusic. and am unable to as of right now.Message Edited by nd4spdbh on 0-08-200803:34 PM

~bump~ ?

I need to upgrade my 10.5.1 os on my G4/1.25 (I'm having some audio-midi setup problems), but it's a machine that is not connected to the internet. Do I have any options? Thanks!

Friends,
I'm having some audio-midi setup problems on my G4/1.25/10.5.1 machine. I'm thinking that a routine OS upgrade might help. However, this machine is not connected to the internet. Are there any alternate methods for upgrading system software? Thanks in advance!

OK, what you should do is download the updates on another machine and burn them to a disc. Start at this link http://support.apple.com/downloads/#leopard for downloads and find, among other things, the 10.5.8 combo updater that works on PPC machines, plus security, QuickTime and other updates. Going from 10.5.1 to 10.5.8, there will probably be a bunch of things that you should install. Being off the internet with the machine, you can't have Software Update sort it out, so something might get missed, unfortunately.
My suggestion is this: if it looks like you might need a download, get it onto that disc.

Setup problem, windows xp, firefox upgrade to 4 and asked to reboot but did not progress. keeps asking to restart even if I try to remove

setup problem, windows xp, firefox upgrade to 4 and asked to reboot but did not progress. keeps asking to restart even if I try to remove

Hi marsano,
Usually the only reason it will ask you to reboot is if there is a file that must be modified that the updater doesn't currently have access to. You should try running the Firefox program once as Administrator:
* Right-click the icon and choose ''Run as Administrator''
If that doesn't help then do a clean reinstall.
# Download a fresh copy of Firefox from the [http://www.mozilla.org/firefox/fx/ Mozilla download page] and save the file to the desktop.
# [[Uninstalling Firefox|Uninstall]] your current version of Firefox and remove the Firefox program folder before running the new installer.
# Run installer
Remember that you don't want to remove personal data when uninstalling. That way you'll still have your personal information.
Hopefully this helps!

After I updated the latest iso 6.0.1 my speaker is problem

After I updated the latest iso 6.0.1 my speaker is problem.
Only the upper one and all the rest is working good ( loud speaker and headset).
Just only the one I put on the ear.
Please help !!!!

Try:
- iOS: Not responding or does not turn on
- If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.

Simple speaker setup for ATV?

I understand if I get bumped because this post isn't ATV-related... But I argue that other ATV users might find this thread helpful. So...
I purchased a new HD TV, one that I will use solely with Apple TV. I want better audio than the built-in speakers. Since I'm not going to need AM/FM radio, CD player, etc., I don't need or want a traditional AV receiver.
I want a 2-speaker speaker setup that can accept an optical audio connection (from the Apple TV)... and that's it. I've seen computer-type speakers that accept a 2.5mm audio cable, from the headphone-out of the computer. The audio signal runs to one speaker, which is the "parent" speaker -- it accepts the audio from the computer, the power input to the speaker system, and then an audio cable that runs audio to the other speaker. I want the same setup... except that it sends an optical audio signal.
Does anyone know of a speaker system that will do this? I don't need all of the bells and whistles of a traditional receiver/speaker setup. Many other Apple TV users out there might have the same, simple needs.

I want a 2-speaker speaker setup that can accept an optical audio connection (from the Apple TV)...
This may be much more than you want, but is I believe what currently replaces my Logitec Z680 which I am still using on my old PPC G5. It is a 505 watt RMS optical input amplified speaker system with 5.1 DD/DTS/Pro Logic II decoder built into the control head. Believe the street price is in the $325-$350 range if interested.

When I want to make a phonecall with my iphone5, I hear absolutely nothing....no ringing and no talking when connection established. When I make the same call but now on speaker, no problem or what so ever, can anyone help me ?

When I want to make a phonecall with my iphone5, I hear absolutely nothing....no ringing and no talking when connection established. When I make the same call but now on speaker, no problem or what so ever, can anyone help me ?

Hello there, RobenCaatje.
The following Knowledge Base article is specific for the issue you're describing:
iPhone: Can't hear through the receiver or speakers
http://support.apple.com/kb/TS1630
Specifically:
Resolution
Verify that there is nothing plugged in to the headset jack, including headsets, headphones, or adapters.
Make sure the Ring/Silent switch is not switched to silent.
While on the Home screen, adjust the volume buttons. If you see the icon below, indicating that headphones are attached, there may be debris or an object lodged in the headset jack:
Check the headset jack. If there is an object lodged in the headset jack that is not easily removed, have the iPhone serviced to remove object.
For Original iPhone: If there is light debris, such as lint, in the headset jack, try connecting a pair of headphones to the headset jack and then remove the headphones. Repeat this several times to remove the debris.
If you have installed a protective film on the display, either ensure that the receiver is not covered or remove the film completely.
Check the receiver mesh (which is on the top front of the device, above the display). If it appears blocked, use a clean, small, dry, soft-bristled brush to carefully and gently brush away any debris.
If you have paired with a Bluetooth headset that is nearby, either use the headset or turn Bluetooth off (chooseSettings > General > Bluetooth).
Restart the iPhone.
If restarting the iPhone doesn't resolve the issue, try restoring the device.
If the issue persists, go to the Service Answer Center - iPhone for information on service.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro D.

Simple VISA Setup Problem

Hi all,
I'm having issues working with VISA in LabVIEW. Previously, I've used Peek/Poke VIs (before they were VISA VIs) that allowed me to read and write directly to registers at a given Windows address. I have a new, custom PCI Express board that uses the same architecture that I've worked with previously only this time I'm trying to access the registers using VISA.
As this is my first time using VISA, I'm having some setup problems. Yesterday I got to a state where logically things should work but I still end up getting an error when I try to run a simple VISA Open command (see attached screenshot).
The initial problem I had was I was not able to acquire a VISA resource that opens a session to my PCIe board...it would simply not show up on the resource list. After reading around I discovered I needed to create a custom VISA driver for my board. Once I did that using the VISA Driver Wizard, the device showed up in my list (as seen in the screenshot). I wrote the simplest of all VIs where I simply open that VISA resource, however, the error seen in the screenshot is produced.
I'm pretty sure this is a simple setup issue, but does anyone know what I'm doing wrong?
Attachments:
Screenshot1.JPG ‏145 KB

Hi bonhomme,
I see you're having some issues using VISA. It sounds like you're new to VISA, so I wanted to pass along some information that we have availble on this software. This link gives good general information about VISA, and the related links are extremely helpful in finding specific issues.
Thank you for attaching your error. This is extremely helpful in debugging since we can actually see the numbers. There is another forumn that talks about these at this link and at this link.
Hope this helps you out!!
Lea D.
Applications Engineering
National Instruments

5.1 Speaker Setup not stick

I just recently got a set of Logitech X-530 speakers. My sound card is the Soundblaster Li've! 5. card. I have verified that I've got the speakers plugged in correctly. I went to the speaker setup in the Creative software and set it to 5. (without digital output). At this point everything works great. However, after I reboot my computer the speaker setup goes back to 2 speakers. I have verified (using Creative's Auto-Update Acti'veX Control) that I have the latest drivers for my sound card. Is this a SB issue or a Windows issue? What do I need to do so that my computer will remember my speaker setup?Thanks.

kinadian wrote:
I do not see a "Synchronize with Control Panel" option in the Surrond Mixer settings anywhere. Where should I be looking for it's
Also, after I've set the speakers to 5., I can go into Control Panel\Sounds and Audio Devices and the speaker setup is configured properly in there. As far as I can tell everything is ok. Until I reboot. Then it reverts back to 2 speakers.
It's more of an annoyance issue than anything else. Since I can go into the settings and switch it back. I would just rather not have to do that everytime I reboot my machine.
On Speaker Settings, not on Surround Mixer.
jutapa

CDC setup problem

{noformat}Dear all,{noformat}{noformat}Trying to troubleshoot a CDC setup problem in ODI:{noformat}{noformat}I got an error when trying to "Start Journal" from the CDC source model (in Designer).{noformat}{noformat}Here is what I've done:{noformat}{noformat}1. grant the following role to the CDC source schema (user):{noformat}{noformat}DBA, execute on DBMS_CDC_PUBLISH, connect, resource, select_on_change_sets, create session, select_catalog_role, execute_catalog_role, create sequence{noformat}{noformat}2. in the CDC source model "Journalizing" tab, specify JKM 9i logminer (CDC source is on 9i) and specify "Automatic Configuration"{noformat}{noformat}3. add a subscriber "SUNOPSIS" to the source model -> Changed Data Capture (Operator successfully run){noformat}{noformat}4. "add to CDC" from source model -> Changed Data Capture{noformat}{noformat}5. "Start Journal" from source model -> Changed Data Capture (Operator run failed with the following errors in the "create Journal" step){noformat}{noformat}
30475 : 99999 : java.sql.BatchUpdateException: ORA-30475: feature not enabled:
ORA-06512: at "SYS.DBMS_CDC_PUBLISH", line 298
ORA-06512: at line 1
30475 : 99999 : java.sql.SQLException: ORA-30475: feature not enabled:
ORA-06512: at "SYS.DBMS_CDC_PUBLISH", line 298
ORA-06512: at line 1
java.sql.BatchUpdateException: ORA-30475: feature not enabled:
ORA-06512: at "SYS.DBMS_CDC_PUBLISH", line 298
ORA-06512: at line 1
at oracle.jdbc.driver.DatabaseError.throwBatchUpdateException(DatabaseError.java:367)
at oracle.jdbc.driver.OraclePreparedStatement.executeBatch(OraclePreparedStatement.java:9119)
at com.sunopsis.sql.SnpsQuery.executeBatch(SnpsQuery.java)
at com.sunopsis.dwg.dbobj.SnpSessTaskSql.execCollOrders(SnpSessTaskSql.java)
at com.sunopsis.dwg.dbobj.SnpSessTaskSql.treatTaskTrt(SnpSessTaskSql.java)
at com.sunopsis.dwg.dbobj.SnpSessTaskSqlC.treatTaskTrt(SnpSessTaskSqlC.java)
at com.sunopsis.dwg.dbobj.SnpSessTaskSql.treatTask(SnpSessTaskSql.java)
at com.sunopsis.dwg.dbobj.SnpSessStep.treatSessStep(SnpSessStep.java)
at com.sunopsis.dwg.dbobj.SnpSession.treatSession(SnpSession.java)
{noformat}{noformat}Any idea?{noformat}{noformat} {noformat}{noformat}William Lam
{noformat}

Hi Cezar,
Thanks for following up. Below is from the description tab of the "Create Journal" steps:
LOADING:
select     FULL_TABLE_NAME     FULL_TABLE_NAME
from     CDCSRC.SNP_TMP_TABLE_LIST     TMP
where     TMP.FULL_TABLE_NAME = 'CDCSRC.DEPT'
and     not exists      (
          select     'X'
          from     CDCSRC.SNP_CDC_OBJECTS     OBJ,
               CDCSRC.SNP_CDC_SET_TABLE     TBL
          where     TBL.FULL_TABLE_NAME          = OBJ.FULL_TABLE_NAME
          and     TBL.FULL_TABLE_NAME          = TMP.FULL_TABLE_NAME
          and     TBL.CDC_SET_NAME          = 'CDCSRC.CDCSRC'
          and     OBJ.FULL_OBJECT_NAME     = 'CDCSRC.J$DEPT'
          and     OBJ.CDC_OBJECT_TYPE          = 'JRN_FULL_NAME'
DEFAULT:
BEGIN
     DBMS_LOGMNR_CDC_PUBLISH.CREATE_CHANGE_TABLE(
     owner          => 'CDCSRC',
     change_table_name     => 'J$DEPT',
     change_set_name     => 'SYNC_SET',
     source_schema     => 'CDCSRC',
     source_table     => 'DEPT',
     column_type_list     => 'DEPTNO NUMBER(2) ',
     capture_values     => 'new',
     rs_id          => 'n',
     row_id          => 'n',
     user_id          => 'n',
     timestamp          => 'y',
     object_id          => 'n',
     source_colmap     => 'n',
     target_colmap     => 'n',
     options_string     => ''
END;
The error message from the Execution Tab:
30475 : 99999 : java.sql.BatchUpdateException: ORA-30475: feature not enabled:
ORA-06512: at "SYS.DBMS_CDC_PUBLISH", line 298
ORA-06512: at line 1
30475 : 99999 : java.sql.SQLException: ORA-30475: feature not enabled:
ORA-06512: at "SYS.DBMS_CDC_PUBLISH", line 298
ORA-06512: at line 1
java.sql.BatchUpdateException: ORA-30475: feature not enabled:
ORA-06512: at "SYS.DBMS_CDC_PUBLISH", line 298
ORA-06512: at line 1
Once again, the setup details:
- CDC source is on Oracle 9i
- KM used is Oracle 9i LogMiner
- enabled archivelog in Oracle 9i
- installed logminer by running the 2 sqls as described in the earlier tread.
I need to meet a tight deadline for POC completion and I desparate need some help here.
Thanks and regards,
William

Will Creative Ever Support The 6.1 Speaker Setup In Vista?

The subject line says it all. I'm disappointed that I have a 6. speaker setup with my X-Fi card that worked great in Windows XP, even the x64 edition. Now since I've updated to Vista, the rear center speaker is no longer enabled. I know the current driver set has a note on this, but just wondering if we will ever get 6. surround support again.

alexs3d2 wrote:
No, because Microsoft doesn't support it.
I'll elaborate on that a bit for you. The 6.1 surround setup is not supported in Vista. This means that (barring some bizzare workaround/emulation effort by Creative), you won't see 6.1 in Vista no matter what sound card/onboard chip you use. It's not up to Creative. Sorry. Microsoft could re-introduce 6.1 with a Vista update. I don't know if it's feasible to do so, but I wouldn't expect anything till Service Pack , as my guess is that would require some major sound architecture changes.

2.1 speaker setup on the SoundBlaster Live24 Extern

I have a 2. speaker setup but I can not figure out how to configure the Li've24 for 2.

I have a pair of Swans M-200's and a Totem Thunder Subwoofer. I have the Swans plugged into the front L+R output and the Subwooder plugged into the Sub/Center output on the Li've24 external. When I select 2/2. speaker output it only shows me the left and right speakers and the test tone will only produce sound out of the front left and right speakers and not the subwoofer. When I click on the "Bass Managment" tab everything including "Bass Redirect" is greyed out. The only way thus far I have been able to get the subwoofer to work at all is if I select 5. then the test tone will produce sound out of the subwoofer.

7.1-7900 Speaker setup problem

Similar Messages

Maybe you are looking for