[7.1] New Capabilities: Point to point mapping

Dear all,
I would like to test new features of 7.1. In this case, I would like to
test the point 2 point connection within adapter engine without
configuring anything in repository.
I found this here
http://wiki.sdn.sap.com/wiki/display/XI/CapabilityandEnhancementsofSAPNetWeaverProcessIntegration7.1
but couldn't found any documentations on this site.
Can you please provide me blogs or documentation links?
Thanks in advanced.
Chris

Hi
Check below links
/people/william.li/blog/2008/02/13/sap-pi-71-mapping-enhancements-series-using-graphical-variable     About Graphical variables
/people/william.li/blog/2008/01/02/sap-pi-71-mapping-enhancements-series-share-user-defined-functions     Sharing of UDFs
/people/william.li/blog/2008/01/02/sap-pi-71-mapping-enhancements-series-import-sql-tables-metadata     Import SQL table metadata
/people/jin.shin/blog/2008/02/15/sap-pi-71-mapping-enhancements-series-graphical-support-for-jdbc-and-rfc-lookups     Graphical support for JDBC and RFC lookups
/people/jin.shin/blog/2008/02/14/sap-pi-71-mapping-enhancements-series-parameterized-message-mappings     Perameterized Message mapping
http://www.sdn.sap.com/irj/scn/index?rid=/library/uuid/b00bbb77-75bc-2a10-6b9a-a6f8161515a6&overridelayout=true        Direct connection in sap pi 7.1
Regards
Ramesh

Similar Messages

  • Point to point mapping with iPhone 3G GPS

    Alright, I'm not really sure it is called "point to point mapping", but here is what I really want to know. I have seen this feature on the Eten Glofish where you can mark a start point on the map (your current location), and as you travel, a path gets created. You can save this new path, go back to it anytime, and navigate through that route. This path can be shared. It seems helpful when you are in places that can be confusing to navigate through, or probably when you go trekking. Is this possible on the iPhone? Is this feature going to be added anytime soon?

    " Is this possible on the iPhone?"
    No.
    "Is this feature going to be added anytime soon?"
    No way to know that unless an announcement is made. I have seen no such announcement.
    Maybe a third party App? Look on the App Store.

  • Creating new mount points on pre installed Solaris 2.7

    Creating new mount points on pre installed Solaris 2.7

    Hi,
    Thanks for suggestion.
    I have checked note 1521371, so as per note I have to provide the locations as given below..
    For PI1 (i.e. PI Development)...............
    Oracle Base Location : /oracle/PI1
    Oracle Home Location : /oracle/PI1/112_64
    Inventory Directory : /oracle/PI1
    For PI2 (i.e. PI Production)...............
    Oracle Base Location : /oracle/PI2
    Oracle Home Location : /oracle/PI2/112_64
    Inventory Directory : /oracle/PI2
    Correct me if I am wrong..
    Could you please tell me, does we need to set the ORACLE environmental variables i.e. ORACLE_BASE, ORACLE_HOME and ORACLE_STAGE before start the ORACLE database installation?
    Kindly suggest,
    Thanks and regards,
    Amit....

  • How do you move a track region in Garage Band to a new starting point without altering the existing length of the track?

    How do you move a track region in Garage Band to a new starting point without altering the existing length of the track? Thanks.

    What exactly are you trying to do? You can drag any region by grabbing it in the middle of the upper area with the highlighted name of the region. However, if you move it towards the end of the track, the length of the track will get longer, to accommodate the extra part of the region. DO you want to speed up the region, to shorten it or do you want to trim it? You can simply grab the right margin of the region and drag it, to make the region shorter.

  • Any enhancement to increase pick time, do not want new shipping point

    Have 1 customer that requires a longer picking time, prefer not to create a new shipping point for a one off case.
    Would perfer to write an enhancement so the material availability date is 5 days before goods issue date (5 days pick time) instead of our normal 1 day.  A new ship point would work great with 5 days pick time but big change for users.
    Thanks,

    Hi Glenn,
            SAP System considers the picking time maintained on the shipping point(OVXD) while giving the Material availability date. Picking date is same as material availability date by defualt. Then it will take picking time as 1day( If you have maintained picking time as 1 day on shipping point) and  gives the loading date. you ask your abaper to hard code  the material availability date (overwrite the praposed date by 4 days for particular customer) in "userexit_move_fields_vbep".Kindly please let me know If you need any more help.
    Regards,
    Ram Pedarla

  • New Entry Point in Cisco Interaction Manager

    I have created a new Entry Point in Cisco Interaction Manager for web chat. I used a new Queue and a new Script for the que script selector. I added a new ICM queue script for the chat, a new Dialed Number / Script Selector. When I test the new chat, the entry point works and shows the new entry point name in the CIM agent, but it still queues to the existing queue in ICM, not the new one. Anyone have any idea what I might have missed?
    Thanks - Keith                  

    Hey Lara, the emails are not getting queued because they are abnormally handled after success path of Queue to skill group.
    please add a wait node, after success path of queue to skill group. set time in wait node to max time you want emails to stay in queue. may be after this you can use another queue or send some label back to CIM, which matches to non IPTA group on CIM.
    the same is applicable for Chat as well.
    coming to the point at the subsequent chat not routing to the same agent, this one depends on max concurrent task you configure in CIM for Chat queue.
    there is config tab in each ICM integrated queue called "Concurrent task limit", this is the one deciding factor on how many concurrent task for each queue an agent can handle.
    please try and let me know if that works.
    regards
    Chintan

  • Can not edit or create new power points since installing Yosemite.

    I can not edit or create new power points since installing Yosemite.  I can open and run the power points I have previously created but every time I try and edit or create a new power point it simple comes up with this
    Also when I open the font drop down menu all the font names are in Chinese

    Have you run all the office updates? We have to assume this is a proper copy of Office 11 of course and not one 'from Hxxx-Kxxx'. I  would also consider re-installing Yosemite-something is screwy on your installation of something if its picking up China..unless of course it is true that the Chinese have been hacking into iTunes and are secretly trying to make you into an agent of the state..you will speak Mandarin..you will speak Mandarin  

  • Setup new access point 1200

    hi
    i have problem in install new access point 1200
    the access point now not connect to any device iam connect the access point using ethernet cable to PC to configure it i try to using GUI but i can not iam setup the PC with ip address 10.0.0.2 and GW 10.0.0.1 and i try to enter to access point but i can not
    i try to use CLI and i connect the access point to PC using console cable and now iam enter to it after the access point start i try to enter to config ter but i can not i get error when i check the command i can not see this command and when i read the manual its tell me to setup ip address using command (lwapp ap ip address) and i try to save ip address using command wr mem or copy run start but i cannot i get error
    in prevelig mode i get only this command
    clear Reset functions8B5E500 00001537 61300D06 092A8648
    clock Manage the system clock
    crypto Encryption related commands.
    debug Debugging functions
    dir List files on a
    led LED lock Lock the terminal
    more Display the contents of a file
    name-connection Name an existing network connection
    no Disable debugging functions
    ping Send echo messages
    pwd Display current working directory
    release Release a resource
    reload Halt and perform a cold restart
    rename Rename a file
    renew Renew a resource
    rmdir Remove existing directory
    save Start to save raise_interrupt_level stack
    send Send a message to other tty lines
    set Set system parameter (not config)
    show Show running system information
    systat Display information about terminal lines
    terminal Set terminal line parameters
    test Test subsystems, memory, and interfaces
    traceroute Trace route to destination
    undebug Disable debugging functions (see also 'debug')
    upgrade Upgrade software
    verify Verify a file
    where List active connections
    how i can setup it and how i can enable the radio
    when i see sh run i see that the ip address is dhcp
    can any one help me please
    thanks

    Hi Nassem,
    It looks like you ended up with a Lightweight AP (LAP Part#) instead of an IOS AP. This can be fixed;
    Reverting the Access Point Back to Autonomous Mode
    http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
    You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
    Using a TFTP Server to Return to a Previous Release
    Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
    Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
    Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
    Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, and c1240-k9w7-tar.default for a 1240 series access point.
    Step 4 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
    Step 5 Disconnect power from the access point.
    Step 6 Press and hold MODE while you reconnect power to the access point.
    Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
    Step 8 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
    Step 9 After the access point reboots, reconfigure it using the GUI or the CLI.
    From this doc;
    http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp161272
    Hope this helps!
    Rob

  • Create new backup point

    How do you create a new individual/independent backup in iTunes for the iPhone, so that that specific backup never gets updated again? When I click on the "Restore from backup" by right clicking on my iPhone in iTunes I have about 5 backups in there from different dates. For example, I have a backup dated Jan 14 2009 that never gets updated anymore, but I know I can revert back to that date if I need to. For the past few months, no new backups have been created, and instead I have regular iPhone backup that gets updated every day. I'm worried that if I have to restore my iPhone, and then I accidentally sync my empty iPhone, I'll have lost all my data because it will just replace the default backup. Is there a way to manually create a new backup that will then never get updated again, for archival purposes? I've tried the "Back Up" option, but that doesn't seem to create a new backup point.
    Thanks in advance!

    For some reason iTunes seems to overwrite the existing backup with a new one, unless (as has been noted) there is a firmware upgrade. It is possible to keep some old ones and force a new backup file....
    Go to the backup location (mac is similar):
    C:\Documents and Settings\<name>\Application Data\Apple Computer\MobileSync\Backup
    And notice the folder names - Noticing the naming convention.... The folder without a numeric ending is current. It is possible to give it a time/date ending and then it will not get overwritten. So if you have a bunch of folders, take the one without a numeric ending, copy it and just add "-20090321-091358" to the end of the copy. To the system it is no longer the current backup, but it was made on date-time.
    I have done this successfully quite a few times - I usually do it before a firmware upgrade, just to make sure.
    Before you backup again, look at the backup list in iTunes and you should see an "old" backup with whatever date and time you gave it. Your next backup should be the same alpha-numeric string and no date-time.
    Message was edited by: tokatta

  • Installing New management Point

    Hi All,
    We want to install a new Management Point in one of our site and remove the existing one.
    could any one please help me what all the steps needs to follow or is there any document available for the same.
    Prashanth Kumar System Center Administrator

    Some good info.
    http://gerryhampsoncm.blogspot.co.uk/2014/05/configmgr-2012-additional-management.html
    https://social.technet.microsoft.com/Forums/en-US/8cd50831-7d1f-4876-acfe-5897dd8cbb96/remove-and-reinstall-management-point?forum=configmanagerdeployment

  • How do i ensure the new access point is joined the controller or not

    How do i ensure the new access point is joined the controller or not

    To Verifying that Access Points Join the Controller or not there are two ways as below.
    Please go through the step by step to find the APs joined state
    When replacing a controller, you need to make sure that access points join the new controller.
    Using the GUI to Verify that Access Points Join the Controller
    Follow these steps to ensure that access points join the new controller.
    Step 1 Follow these steps to configure the new controller as a master controller.
    a. Click Controller > Advanced > Master Controller Mode to open the Master Controller Configuration page.
    b. Check the Master Controller Mode check box.
    c. Click Apply to commit your changes.
    d. Click Save Configuration to save your changes.
    Step 2 (Optional) Flush the ARP and MAC address tables within the network infrastructure. Ask your network administrator for more information about this step.
    Step 3 Restart the access points.
    Step 4 Once all the access points have joined the new controller, configure the controller not to be a master controller by unchecking the Master Controller Mode check box on the Master Controller Configuration page.
    Using the CLI to Verify that Access Points Join the Controller
    Follow these steps to ensure that access points join the new controller.
    Step 1 To configure the new controller as a master controller, enter this command:
    config network master-base enable
    Step 2 (Optional) Flush the ARP and MAC address tables within the network infrastructure. Ask your network administrator for more information about this step.
    Step 3 Restart the access points.

  • Create New Entry Points

    Hi All,
    I have a requirement to display a folder as an Entry Points in KM.
    Same as displayed in the blog [https://www.sdn.sap.com/irj/scn/weblogs?blog=/pub/wlg/1027]
    I have done the configuartion as mentioned the blog still I am not able to view the folder.
    Request your support to achive the same.
    regards,
    SJ

    Hi
    Thanks for the link; still I am not able to view the new entry point for my folder.
    My requirement is to have other folder displayed in SAP standard favorites.
    Presently, below mentioned folders are displayed:
    --> My Room Folders
    --> Favorites
    --> Personal Documents
    --> Recently Used
    --> Common folders
    --> Public Documents
    --> More...
    I need to add a new folder
    --> XYZ
    I have followed the instruction mentioned in the wiki, but I am still not able to view a folder appearing in KM favorites.
    Regards,
    SJ

  • Unable to create Transfer Order manually for a new Shipping Point

    Hi folks
    After spending a couple of days investigating what the problem, I am resorting to my last option of posting here. I am hoping one of you can help me here.
    Due to a new business requirement, I am having to create a new Shipping Point. We use Lean WH. I have performed the following steps
    Created a new shipping point under Logistics Exec
    Created a new Shipping Point and assigned it to the plant (under ENT Structure)
    Created Shipping Condition
    Assign Shipping Point to Shipping Condition
    Changed Customer Master Shipping condition to the new SC.
    Assigned the storage location for the new Shipping Point and the Plant under SPRO-LE-Shipping-Picking-Determine Picking Location- Assign Picking Location
    When I create an Order, a delivery gets created automatically. Now when I try to create a TO in VL06P in the background, I get an error VLA029
    WM-TO: 0 deliveries successful, 0 with errors, 1 not relevant
    As far as I am concerned, all the steps are completed.
    Can someone please throw some light on how to get this fixed.
    Thanks in advance to everyone.

    For the said error, SAP have given the following procedure
    The above is self explanatory and have you tested in line with the above.
    G. Lakshmipathi

  • HT1766 I hooked up my phone because I needed to restore my contacts, instead my phone set up a new restore point losing all the info I wanted.

    I hooked up my phone to my computer so that I could have my contacts restored, instead it made a new save point effectively losing the info I needed.  Is there any point to backing up your phone?

    Ocean20 wrote:
    I thought itunes only keeps the latest backup and every time you do a new backup it overwrites the old backup
    iTunes will keep all backups until you delete them.
    When you Restore from backup, iTunes renames the current backup and adds the date to the name and new backup is named Your_iPhone_name iPhone.
    iCloud will keep backups until you delete them. You are not necessarily limited to 3 but Apple can limit you to 3 iCloud backups.

  • How do I create new mount point

    Hello,
    I'd like to create a new mount point. The Admin guide says to click the Create button on the toolbar but I don't see anything that says Create (I have New, Edit, Upload,...).
    Searching here I've seen references to some code snippets that purport to do it but I'd rather use a GUI.
    Thanks for any help

    You have to use iFS Manager, not the WebUI.

Maybe you are looking for