702W Access Point and Bi-Directional Rate Limiting

Has anyone checked whether BDRL (Bi-Directional Rate Limiting) is supported on relatively new 702W APs.
I need it to work in FlexConnect mode.
Thanks,
Nick

It is not supported,
http://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/113682-bdr-limit-guide-00.html

Similar Messages

IOS 6, Netgear access point and Internet

Hi,
I’ve reached a point where I’m not entirely sure what to do next.
Here are some quick details (all are on most recent firmware unless stated):
Router: Draytek Vigor2830n
Access Point: Netgear WG102
Devices: iPhone 4, iPhone 5, iPad 2 and two iPad 2’s for comparison on iOS 5.
So, all devices running iOS 6.1.3/4 will connect to the Netgear access point just fine, can browse the LAN / stream media from network shares but internet access seems to be 'delayed' and can take anywhere between a minute to 20 minutes to connect (I give up after this). In comparison both the iPad 2’s running iOS 5 will gain internet access immediately after connecting to the access point.
On the other hand, when connecting to the routers wireless on all devices it works flawlessly and internet connection is 'instant'.
Given the problems that Netgear wifi has had with iOS 6, which were supposedly ‘fixed’ in iOS 6.1, I’m not sure what to do. It’s definitely a software problem, and could well be something to do with the router (along with connecting to the access point and iOS 6), but I’m not sure what to start changing first. iOS 5 works fine, so what has changed in iOS 6 to break it?
Its not a security issue like before 6.1 and not being able to connect to the access point at all.
Basically:
- I either need to figure what in iOS 6 is causing this ‘delay’ and how to fix it
-Give up on the access point and buy a new one (seems a bit extreme given that every other devices works fine – iOS 5, blackberry, laptops etc).
-Wait for iOS 7, hopefully in the next couple of weeks and see if it fixes it, though I can find little information on this issue as it is, and nothing to suggest iOS 7 might help. Though if iOS 5 is fine, iOS 6 broke it and 6.1 slightly fixed it, maybe iOS 7 will cure it? Doubt it…but worth waiting a few days.
Anyone got any suggestions? I have been through all the usual (HTTP proxy, forget this network, reset network settings), nothing makes it work flawlessly like iOS 5 and the issue is the same on a wide spread of devices running iOS 6.

Dont know my routerand access point works fine. Try http://support.apple.com/kb/HT4199 and make sure your setting are correct.

Silly doubt abt access-points and bridges

hi all i have read cisco doc wherein clients connecting to access-points and also where the cisco access-point is working like a bridge and still clients can connect to it .
then any specific reason why people generally connect clients to access-points.
i mean is there any benefit of either method over the other.
any help and guidance would be really helpful.
regards
sushil

In short, it is preferred to have users connect to access points.... 99% of the time. You can use a wireless bridge (that is associated to an AP) that is connected to a switch/hub to supply network connectivity to wired users off the switch/hub. There are also access points that can be used as a bridge for building point to point connectivity.
Look at the home users with wireless.... it allows then to move from place to place (as long as there is coverage) without having to be wired in.

Use N95 as access point and get laptop inet throug...

Is it possible to use the N95 as an (WIFI) access point and use a laptop, a psp, an ipod touch to access the internet through 3G or even Turbo 3G?
That would be really really cool!
Regards
Raptor

I dont think it is as would have to be connected through a router to a phone line anyway. My psp doesn't even detect my N95. You would have to use it as a bluetooth modem and 3g.
Its not who i am underneath. But what i do that defines me.
You are here for a reason Superman.
"Come to me son of Jor-EL. KNEEL BEFORE ZOD"

Connection between lightweight access point and switch?

Hello everybody,
I am a bit confused about cisco 1000 series access point connection. On wireless lan controller and lightweight access point basic configuration example document id 69719 (http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a0080665cdf.shtml), I understood the access point has two vlans associated with (vlan 3 and 4). Am I correct?
Why is connection between access point and catalyst port just access port rather 802.1q trunk? How vlan traffic can traverse from the access point to controller?
Please advice.
Many thanks,
Nitass

Nitass,
The AP itself does not need to be a trunked port, but the uplink to the controller does. When using a Lightweight enviroment, all the traffic passes thru an encrypted LWAPP tunnel from the AP to the controller, and then gets sent out the correct VLAN interface on the controller.

WRT54G ver. 6 Connected to access point and internet, but cannot access the web

I can connect to the access point and it shows that I an connected to the internet. However when I open a bowser it says page cannot be displayed! Signal is very good to excellent. Also, I have been using it all day and it was working fine, until I shutdown. When I booted back up it stopped working. The internet is working! I have XBOX Live working right now. Just not the computer. Any Help would be appreciated.
WRT54G ver. 6
Message Edited by SJohnson4 on 12-01-200607:35 PM

Hi... it seems that your Wireless adapter on does get a IP address or DNS no after reboot. Try assigning a Static IP address and DNS on the Wireless Adapter. Also try to update the drivers for that wireless adapter.

Multiple Cisco Aironet 1131AG access points and same SSID?

We have multiple Cisco Aironet 1131AG devices, all wired on one Cisco L2 switch(2560) who is connected to L3 switch (3550). We assigned one VLAN for access point in L3 switch who acts as vtp server (L2 switch is vtp client). All ap's will have static ip address and all will have same SSID and no security and they will be using multiple channels (ex. 1,6,11). They will operate in 3 floor building for roaming wireless client. We won't using any wireless controller.
So my question is this: How to configure APs-all the same with different ip's, can we use L3 switch to create dhcp server for access points VLAN (pool for clients, and the rest for static ip for ap's)? Can one of the ap's be WDS and in the same time local radius server with users without Cisco Secure ACS or similar controller or I didn't understand this quite well :-). I followed guide http://www.cisco.com/en/US/docs/wireless/access_point/12.3_2_JA/configuration/guide/s32roamg.html for WDS where the part abou Cisco ACS is a problem, so I can use same ap as Local Authenticator as in guide http://www.cisco.com/en/US/docs/wireless/access_point/12.3_4_JA/configuration/guide/s34local.html#wp1035723.
Many thanks...

Well, just so you know, WDS and local RADIUS authentication is only needed if you're using authentication on your wireless connection. You say you're not planning to use security, so this isn't necessary. However, I'd highly recommend at least using a simple WPA2-PSK to lock down your connection, otherwise you might end up giving free Internet access at best, and at worst you might be giving access to company PCs and servers. If you want to further use an 802.1x or WPA authentication method, then yes, you can use an AP as a RADIUS server and WDS to improve authenticated roaming, but this is far more limited than using a Cisco ACS.
As for your other questions, yes, your APs can all be configured the same except for at least three parameters: IP address, channel, and hostname. Configure your static IP addresses on the AP's BVI1 interface. Don't place it on the Radio or Ethernet interfaces, because if either of these interfaces goes down you'll lose the ability to configure the AP, so it's best to use the BVI1 interface.
And yes, configuring a DHCP scope for your clients on your L3 switch is a good design, or you could also use your DHCP server on a different subnet by using the ip helper-address command on the L3 interface. I hope this helps! Let me know if you need help configuring any of this.
Merry Christmas!
Jeff

Cisco 877 as access point and DSL router - 2 subnets

I have been using an 877 to provide DSL access and wireless access point from two separate wired subnets. The idea is that traffic from one subnet will be routed to the DSL connection. The other subnet provides a bridged connection to wireless clients. Both subnets being isolated from each other. In the former case the router acts as DHCP server, whilst in the latter case a separate DHCP server is used. Despite all apparently working, recent introduction of a wireless client did not work and seemed to be acquring a DHCP lease from the router rather than the external DHCP server. It seems that broadcast traffic from the router DHCP server was traversing to the wrong interfaces, despite (I hope) only the wireless and the second wired subnet being in the bridge group.
I would be grateful if anyone can throw any light on this, the salient parts of my config are enclosed below. I have anonymised the public addreses using q1.q2.q3 therein. Many thanks.
dot11 ssid MYSSID
   authentication open eap eap_methods
   authentication network-eap eap_methods
   authentication key-management wpa
   guest-mode
no ip source-route
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.10.10.1
ip dhcp excluded-address q1.q2.q3.15 q1.q2.q3.254
ip dhcp excluded-address q1.q2.q3.1 q1.q2.q3.8
ip dhcp pool sdm-pool1
   import all
   network q1.q2.q3.0 255.255.255.0
   domain-name MyDomain
   dns-server x.y.z.1 x.y.z.2
   default-router q1.q2.q3.3
bridge irb
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
switchport access vlan 10
spanning-tree portfast
interface FastEthernet3
switchport access vlan 10
spanning-tree portfast
interface Dot11Radio0
no ip address
encryption mode ciphers tkip
ssid mySSID
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 spanning-disabled
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
interface Vlan1
description $ES_LAN$
ip address q1.q2.q3.3 255.255.255.0
ip access-group 102 in
ip nat inside
ip virtual-reassembly
interface Vlan10
no ip address
bridge-group 10
interface BVI10
ip address 192.168.253.251 255.255.255.0
bridge 10 protocol ieee
bridge 10 route ip

If the Router is not the DHCP server, you'll want to put an ip helper-address under teh BVI 10 and point to the correct DHCP server
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered

How to add a second router as access point and wifi signal extender

Previously I had 2 linksys routers and was able to configure them as one in separate areas of my house. I think it is called cascading. The 2nd router acted as an ethernet switch with 4 extra ports and it provided a wifi signal to areas of my house that previously had a weak signal when I used only one router.
I have since switched to an Airport Extreme as my main router. I can't seem to get the same configuration with the linksys router, it is Model E1000 and has an "N" signal. The Linksys E1000 I think is the newer model of the old WRT54G Linksys. I can't get it configured to work. I have searched high and low on the internet and can't find anything simple enough for a novice to understand. I did read something that I may have to assign a "DHCP Reservation" on the Apple Extreme. I couldn't figure that out.
Can somebody please offer some guidance on how to get this to work?
Thanks

You have two routers producing two networks with the same name, so they will show up as two networks on any type of scan by a wireless utility. This is normal.
If you had used two Linksys devices, they would probably show up as one network, not two. Linksys has a feature that allows this to occur, but this is not true of Apple devices.
As long as the wireless network name, wireless security and password match up between the two routers, the two networks will behave as if they were one. As computers change location, they will automatically connect to the wireless access point with the strongest signal.

Wireless bridging is not working in 1552 outdoor access point and 2602e indoor access point.

Hi,
I am have been tested wireless bridging with 2 indoor Cisco 2602 access point by following the attached document and its working fine without any issue.
After then I made one Cisco 1552 EU-M-K9 outdoor access point as RAP, then connect to this RAP with one 2602 mesh access point. But its not working, mesh access point is just start scan the signal to get associate with RAP, but not getting established. Is there any specific configuration required to connect between outdoor and indoor access point. Kindly find the attachment and advise.
regards,
Jubair.S

Hi Team,
Any suggestion??
Regards,
Jubair.S

Trying to get home shaing working on apple tv using Cisco Access points and a Cisco WLC 5508 with 7.2.110 code. I can get devices working individually but they never see each other. I can ping the apple tv from my laptop and ipad.

Trying to get home sharing working on a corporate wireless network. Cisco wireless.
WLC5508 controller
Cisco 3502 access points
All apple devices on same WLAN - security WPA2-PSK
ITunes account up to date
All devices laterst software.
Can ping apll tv from laptop
can ping apple tv from ipad
Can ping ipad from laptop
can ping laptop from ipad.
Apple tv never sees any other device.
Any ideas?

Fascinating just reading about your setup. I have a WRT350N and have noticed that it will drop its speed, sometimes down to 1Mbps. It seems to do so at about the same time every day, but usually comes back to speed in about 5 minutes. In my experience, the Apple TV will disconnect if the speed falls this low. Try monitoring the Linksys with Netstumbler, Vistumbler, or just in the Windows Network utility.
Check the "lease obtained" and "lease expired" times for your router to see if that is when the network fails. I've just finished reading an angry thread over at the Linksys forum about the WRT330N where someone mentioned that the router wasn't renewing its lease.
"I cannot set it run off automatic DHCP from the WRT330N, the router will not assign it an IP every time the lease expires, causing me to have to manually set an IP on the Print server. That's annoying. Having the router drop IP's to individual machines after 12-48 hours...very annoying."
http://forums.linksys.com/linksys/board/message?board.id=Wireless_Routers&thread .id=67412
If that is the problem, then I would consider setting up a Static IP address for your Apple TV. You can do that through the user interface -> Settings -> Network -> Configure ... (Quite intuitive as you only have change IP address and the subsequent details remain the same.)
My router assigns IP Addresses in the ranges of 192.168.1.100 ->149. The idea here is to choose an address outside of that range but is not greater than 192.168.1.253 (and should not end in the number 1). You shouldn't have to change the linksys router as long as 50 clients are assigned in that range. You'll have to figure that out by accessing your router webpage at browser address 192.168.1.1 -> the default password is "admin" (without the quotes).
Good luck.

6120c - default access point and setting applicati...

Does anyone know how to set the default access point on the 6120, for all apps? And how to allow apps to access the internet without asking? The default browser is ok but everything else (Opera Mini, Gmail, Google Maps etc) asks for permission, then an access point. I figured it out on my N73 but can't get it on the 6120.

Thanks for the reply. I've looked in App Manager but the only context-sensitive stuff for each app is 'details' which is just the vendor and certificate, and 'settings' which is 'Software Installation', Online Certificate Check' and 'Default Web Address'.
Doh! Just got it - choosing 'open' doesn't start the app, it gives me the options I need. Problem solved!

HP photosmart 7520 connects to wrong access point and looses connection

I recently installed a remote wireless access point in an outbuilding. I'm using a router with the same SSID and password as my main router with the same security settings. Only the main router is set to issue IP addresses. The system works fine with two laptops, a desktop, an Ipad and an Ipod. It provides continuous connections from my house to the outbuilding. Only the HP Photosmart seems to be an issue. At first the system worked fine then after a couple of days it lost its connection. I tried to the Wireless Setup Wizzard with no success. The Wireless Network Test results indicated that MAC address filtering may be enabled. This is not the case, MAC filtering in not enabled on either router. The next morning the printer was fine and connected again. I suspect that it is detecting the remote router and trying to connect through it. During the setup a warning came up indicating that two routers were detected with the same SSID and Password and that the printer might try to connect to the wrong router. It should not matter since the remote router connects and is issued IP addresses through the main router. The only difference in the routers is the BSSID. This uses the same number as the MAC filtering address, so I suspect this may be the problem. Any suggestions on a work around. The only thing I have found that solves the problem is turning off the remote router.

Hello there -
Is it possible your new remote access point only supports the 5Ghz band for N connection, or that it's connected to your primary router through a wireless N connection in the 5Ghz band? The 7520 only supports 2.4Ghz N connections. If your primary access point supports both 2.4Ghz and 5Ghz, that is likely why it's able to connect there while it cannot connect to the new access point. Many newer laptops and iPad/pods utilize 5Ghz N, which would explain why they can connect and your 7520 cannot. I'd recommend moving the 7520 closer to the primary router and using AirPrint to send your jobs.
***I am an HP employee***
The comments above represent myself and do not reflect the opinions of HP.

Design question: Access points and controller Logical/Physical placement

Background:
We have an MPLS (layer 3) network 4 offices and a Datacenter:
We are planning to install about 10 Access Points(3600 series) per office and have a controller(5508 series) in the Datacenter.
Questions:
1- Is this design possible, in other words, just one controller centralizing all Access point traffic in one controller in the Datacenter?
2- We would like to accomplish this in two phases:
    A- install access points without controller handling authentication thru microsoft IAS servers (current configuration with 1200 series)
    B- Deploy wireless Controller in Datacenter and start migrating orphan APs to Controllers one office at a time
I'll appreciate any advice , comments and suggestions to the the outlined plan/design
Thanks
Juan

1- Is this design possible, in other words, just one controller centralizing all Access point traffic in one controller in the Datacenter?
Yes... depending on the bandwidth you can either have the APs in local mode which tunnels all traffic back to the WLC or you configure the AP's in FlexConnect and place the traffic locally in each site.
2- We would like to accomplish this in two phases:
    A- install access points without controller handling authentication thru microsoft IAS servers (current configuration with 1200 series)
    B- Deploy wireless Controller in Datacenter and start migrating orphan APs to Controllers one office at a time
I don't know what you are trying to accomplish here, but if you are running new cables and replacing all the AP's, you should bring up the WLC in the DC and connect all the AP's but leave the AP as admin down until your ready to cutover. You can still use the IAS server for radius, just need to create a AAA client on the IAS for the WLC.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Cisco autonomous access points and WCS

Hi, I'm trying to add my autonomous access points to WCS which I have done but I'm not getting any performance data or errors etc.
Does anyone know if WCS support autonomous access points or do I have to use WLSE to get this info
Thanks

Greetings the WLSE will be needed to manage autonomous access points. The WCS application is geared towards LWAPP and Controller based implementations.
For a comparison please see the following document.
http://www.cisco.com/en/US/products/hw/wireless/products_category_buyers_guide.html#http://www.cisco.com/en/US/products/hw/wireless/products_category_buyers_guide.html?linkpos=4#number_4
Regards

702W Access Point and Bi-Directional Rate Limiting

Similar Messages

Maybe you are looking for