7510-e-all in one - c311a will not connect to my router dlink wbr-2310.

I just bought HP Photosmart 7510 e-All-in-One-C311A and it will not connect to my router which is a DLink WBR-2310. The diagnostic results are as follows:
Wireless On: PASS
Wireless Working: PASS
Connected: Not Run
Disconnect count total: 0
Disconnect count (last hour): 0
Disconnect count (last 24 hours): 0
Network Name (SSID) Found: PASS
Other Networks detected matching your network name (SSID) No
Wireless Networks Detected: 10
Printer Settings Consistent with Wireless Router Settings: PASS
No Filtering: FAIL
Channel: Not Run
Security: PASS
I have checked to make sure MAC addres is not enabled. I have tried turning off computer, router and printer. Please help. I have Windows 7.
Thanks very much!

Hi,
This is how I installed my printer last week (also a 7510).: Using USB cable to connect it to a computer on your network and setup from there. It will ask you to use similar setup for your computer, just accept this The setup was no longer than 5 mins.
Please also check this:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02900814&lc=en&cc=us&dlc=en&product=5070121
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Similar Messages

HP Deskjet all-in-one F4440 will not print

My HP Deskjet all-in-one- F4440 will not print. I have put in a new color and a new black cartridge. It clanks loudly when it moves back and forth. Finally it stops and then pulls plain paper through as though printing on it - does this two or three times. then it pulls plain paper halfway through and stops. I have to tug and carefully pull halfway paper back out towards front to remove.

Hi there,
Could you provide the community with a little more information to help narrow troubleshooting? Are there any error messages or flashing lights? What operating system are you using?
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

I updated an iPod touch, an iPad 2, and an iPhone 4 to iOS 6, and all of them now will not connect to WiFi. They all give this wierd 404 error page from Apple and insist that I need to login to the network. Bad job testing the software Apple.

I updated an iPod touch, an iPad 2, and an iPhone 4 to iOS 6, and all of them now will not connect to WiFi. They all give this wierd 404 error page from Apple and insist that I need to login to the network. What's the fix? None of the recommended fixes work in any of these devices. Reset device, reset network, renew lease, etc. None of them work.

Does the iPod work OK?
Does it charge when connect to the computer?
Does it appear in My Computer?
Look at the dock connector on the iPod. Compare with the iPod that does work/connect.
I suspect you have a 2G iPod. Those can only go to iOS 4.2.1
http://support.apple.com/kb/HT1353#iPod_touch_late2009
iPod touch (3rd generation)
iPod touch (3rd generation) features a 3.5-inch (diagonal) widescreen multi-touch display and 32 GB or 64 GB flash drive. You can browse the web with Safari and watch YouTube videos with Wi-Fi. You can also search, preview, and buy songs from the iTunes Wi-Fi Music Store on iPod touch.
The iPod touch (3rd generation) can be distinguished from iPod touch (2nd generation) by looking at the back of the device. In the text below the engraving, look for the model number. iPod touch (2nd generation) is model A1288, and iPod touch (3rd generation) is model A1318.

HP all-in-one c301 will not save scanned doc in Mavericks upgrade

I have recently installed the free OS X Mavericks upgrade to my Macbook Pro. My HP all-in-one c301 will scan, but the scans do not save. The saved pdf looks like a bunch of gray lines when I reopen the saved file. Has anyone already found a work around? Unless I missed a webpage, HP does not have drivers or apps for Mavericks at this time.
It seems that nearly everything related to any imaging has stopped working with the new OS. (This situation is not good for someone who uses their system for photography related work only.)

Since maybe 1 in 10,000 are having such experiences, we have to guess that there is something wrong/corrupted in your Mac's Mavericks install. This happens (just slightly) more often, now that everything is downloaded from the internet.
Try some generic repair steps:
1) Restart in Recovery mode and use Disk Utility to repair the hard drive and permissions.
OS X: About OS X Recovery
(Just read the first paragraph about how to get into Recovery)
2) Download and install the 10.9.4 COMBO update (this isn't from Software Update - it replaces all the files from all the updates)
http://support.apple.com/kb/DL1755
3) Reset the Printing System, and re-add the printers (& scanners)
OS X Mavericks: Reset the printing system
You should experiment and see if things improve after each step.

TS1398 Have 3 iPods and 3 iPads in our house. Our Internet is dlink. Two iPods and one iPad will not connect. Help?

We have 3 iPods and 3 iPads in our house. To of the iPods and one of the iPads will not connect to the Internet. Our Internet is dlink. Can anyone help?

Do the devices connect to other networks?
Do they see the network?
Any error messages?
Do other devices now connect?
Did they connect before?
Try the following to rule out a software problem:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on the router
- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar

PR0BLEM:One computer will not connect thru the hub

umm...well the problem is that there are 2 computers connected thru the hub but one says Limted or No Connectivy the other works fine we called the ISP and they said its the modem but its reciving a connection what could be wrong?

typically only one PC will go online through the router....what you need to confirm with your ISP is , how many IP's are they assigning to you at any given point of time....In case it's just one IP....I'd suggest that you get a router instead of using a HUB.

After installing windows 7, will not connect to my router

I installed windows 7, 64-bit on my macbook late 2009 model. After installing, it would not connect to my router. However, it did connect under Mac OS X and it also worked with my roommates laptops, but not my macbook running windows 7. I searched everywhere and could not find a solution. Tried updating drivers (updated to bootcamp for windows 64 bit, 3.1 and then 3.2). Tried setting it up manually. Also, did not work. Does anyone have any solutions for this? It seems a lot of people are also having this issue.

For wired or wireless if you have not already done it,
1) Remove router cable from Modem,
2) Unplug Router power,
3) Unplug Modem power,
4) Wait a few minutes
5) Replug Router power,
6) Replug router cable to Modem
7) Replug Modem power
Also router may in combo with more modern (if wireless?) PC have security (password setup) requirement.
I.E. http://support.dlink.com/emulators/wbr2310/wireless.htm
and a CD that came with it for setup on your computer.

My hp all in one printer will not link to my new router.

I have a hp all in one printer deskjet 3510 model and i just got a new belkin N600 router and they will not link for wireless printing. The printer just times out when I try to get them to link. I use the push button setup because thats what i have. How can i get them to link. I had no problem with my old router it was a linksys.

Replacing your wireless router try here.
http://www.hp.com/global/au/en/wireless/reconfiguring-system-help3.html
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

HP Deskjet All in ONe L7650 will not print black only --

Started doing this with previously working black cartridge, updated software--prints, but blank page comes out when set to black ink only; prints other colors.
Changed black print cartridge and still will not print black. Diagnostic page prints other colors.
Printhead health shows good for all colors.

What brand of printer cartridges (not printhead) did you use the last time you changed them? I don't know if it was because one or both of my printer cartrdiges went dry, but I put new cartridges in (not printhead) and it improved somewhat--I kept trying to clean the printheads but it seemed to never get resolved.
I refuse to have to buy new printheads. I tried several cycles of "align printheads" "clean printheads" and never got a decent print out, but I did get to the point of all the colors printing although magenta printhead makes printing errors and so I never know what I am going to get with color anymore.
It seems to be at its worst when printing in "draft" but in normal or best (with more ink coming through) it seems better--the higher ink volume seems to cover some of the problems with the printheads.
So, I am justing using it "as is" and not replacing the printheads--because it is a waste and yes, could almost get a new printer for this cost.
I wish I had never gotten this All in One and just stuck with the old 970 csi and the old UMAX scanner, which was a better scanner, but thought I would "save some space" by getting this since it scans legal, which I needed.
Just keep trying to reseat the printheads (also trying to reclean them, which seems to make it worse) and keep printing out those "tools" alignment and cleaning procedures.
But no help from HP.

HP C5280 all-in-one printer will not print yellow

I tried cartridge replacement. Update driver, and clean head. Nothing works. I had this printer in a box for three years without using. Now It will not print yellow or green.

Happy Monday edam. Green is actually the result of two or more color mixed together. Lets try printing a self test report:
Make sure the All-in-One is on and loaded with unused, plain, white paper.
Press Setup . The Setup Menu appears.
Press the down arrow button to select Tools , and then press OK .
Select Self-test Report , and press OK . The self-test report prints.
Let me know the results of the self test. Are all the colors present on the self test or are you missing specific colors?
Thanks!
-SeanS
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

HP C7200 All-in-One printer will not print through the Wifi network

I have used the HP printing and scanning Doctor but none of the proposed solutions have solved the problem. The blue light for wirelwss 802.11g service is on and connected to the same Wifi address as my laptop is using now. My Dell laptop is running Windows 7 and the printer works if I use the USB connection instead of the Wifi. Any suggestions?
Larrypat
This question was solved.
View Solution.

Welcome to the community @Larrypat
I understand your printer is not connecting wireless and only connecting USB. I have some questions and ideas for you that should help. Let's get to it!
Could you please remove the USB cable, run the Print and Scan Doctor again and send me a screen shot of the results from running the diagnostic tool?
Also let me know which model from the C7200 series you have:
HP Photosmart C7250 All-in-One Printer
HP Photosmart C7280 All-in-One Printer
HP Photosmart C7288 All-in-One Printer
Try power cycling the network devices:
Turn off the printer and computer and unplug the router for 1 minute (do not press any buttons on the router).
Plug the router back in and wait another minute, next turn on the printer and computer. Run the Print and Scan Doctor afterwards and try printing.
Let me know how it goes and the results
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

HP 7780 All in One Printer will not print PDF files!!!

I have an HP 7780 All in One printer setup as a network printer. It will copy, scan, and print everything except PDF files. Why will it not print PDF files? You send a PDF file to print. The printer spins up like its about to start printing and then nothing. No error message or nothing. Nothing even shows up in the print queue as waiting to print.

Happy Monday edam. Green is actually the result of two or more color mixed together. Lets try printing a self test report:
Make sure the All-in-One is on and loaded with unused, plain, white paper.
Press Setup . The Setup Menu appears.
Press the down arrow button to select Tools , and then press OK .
Select Self-test Report , and press OK . The self-test report prints.
Let me know the results of the self test. Are all the colors present on the self test or are you missing specific colors?
Thanks!
-SeanS
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

HP Photosmart C6180 All-in-One printer will not work

Printer worked one day and the next day it did not and now will not turn on. I did not turn it off. It went off all by itself. Only 3 years old and not over used. Have checked outlet and power cable. Green LED light comes on when connected to outlet but as soon as I connect it to the printer, the light goes out and the printer will not turn on. Is it dead?

I have the exact same problem
Where do we find a solution

HP All-in-One 7400 Will not Power On

Hello -
We have an Officejet 7410 that, when plugged in, will not power on. The "HP invent" screen and a scrolling white bar that one sees before the power button is pushedstays on, but the printer will not turn on when the power button is pushed.
I've restarted computer to which it's connected, tried different outlets and power strips, checked USB connections, all to no avail.
Has anyone ever had this issue?
Is it possibly in some sort of 'sleep' mode?
Thank you.
Hildreth @ TALHFA

If you can live without the wireless capability the following solution may help.
Regards,
Bob Headrick, Microsoft MVP Printing/Imaging
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

HP Pavilion 23 All-in-One PC will not turn on

Was away this weekend, before leaving on Friday I updated my computer and then shut it down. When I returned today it will not turn on. I have disconnected it and reconnected everything and still no luck. It was plugged into a sugre protector but no significant weather that would have caused issues. Electricity did not go off over the weekend. I have no idea what could be wrong. I just bought this computer in March of this year. Any suggestions or ideas?

Hello @Harold-N-Tville,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I understand that after running some updates and turning your computer off for the weekend your HP Pavilion 23 All-In-One Desktop PC will not start. I would ensure that you try your computer plugged directly into the wall and if still does not work please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region. http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html. Given how new your computer is you want to ensure that any issues are properly documented and dealt with.
I would like to thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

7510-e-all in one - c311a will not connect to my router dlink wbr-2310.

Similar Messages

Maybe you are looking for