785gm e65 and ssd

Hi, i have the msi 785gm-e65 moptherboard and i would like to ask if it supports ssd drives and trim.I am interested in installing an samsung 830 ssd.

Quote from: Fredrik on 19-January-12, 06:30:30
A bit off: Does anyone know why they call it IDE mode? Whether a hard disk uses "AHCI" or "IDE" mode it is still usually an IDE sized disk.
Sorry Fred, it's actual a reffering to the circuitboard on the drive, nothing more.
In the old days they used to have "smart" controllers and dumb drives.
Now they have dumb controllers and "smart" drives, as such they moved the electronics to the drive.
The protocol the drive uses is ATA or AHCI, funny is that RAID isn't a protocol for the drive to use

Similar Messages

  • 785GM-E65 and video out

    I am looking for an analog video out solution for this mobo. I bought a VGA to component video cable and that gets me an output with jiberish. I'm aiming for s-video or component. I read that some mobo's support s-video out through the VGA port. Does anyone know if MSI has included this feature on this mobo? I have not found any materials that indicate one way or the other.
    Thanks for the help.

    This board doesn't support that kind of video output. You could get a video card with super video out or get something like this converter.
    http://www.newegg.com/Product/Product.aspx?Item=N82E16815158142&cm_re=vga_to_composite-_-15-158-142-_-Product
    Good luck!

  • MOVED: 785GM-E65 and IOMMU for Xen virtualization

    This topic has been moved to Linux/Unix.
    https://forum-en.msi.com/index.php?topic=135607.0

    Or maybe a dead mobo.
    Is the Power Supply able to feed a fan for more than 30 minutes ? It can happen the PSU to start up and because of a failure capacitor to shut down itself after 5-10 minutes by it s own.
    You ll need to swap mobo ,CPU and PSU to see what happens.RMA the 3 hardware pieces and see what the reseler tells you.
    I would recheck the PSU too having in mind the failure even if it looks good.
    When you get all back working stay with the multimeter connected and see if there are any spikes when you boot or when you load heavy aplications.
    Any overclocking on the machine ?
    Have you tryed with the mobo outside of the case on some wooden surface ?

  • MOVED: Sos Voltage Settings on MSI 785GM-E65 Help Help SOS

    This topic has been moved to Overclockers & Modding Corner.
    https://forum-en.msi.com/index.php?topic=136226.0

    Actually it concerns the Voltages.
    When I installed this CPU in this board everything was AUTO, in Windows the Voltage read 1.4v.
    This 955 Black Editions has Stock Voltages of
    CPU VDD 1.35v
    CPU-NB VDD 1.25v
    HT Link 1.2v.
    However because the BIOS does not output all these voltages in the Right Column as to what they are set to reflecting realtime measures, one has to 'boot' into Window to look at the readout. 
    BIOS Terminology is my main concern so I can set them appropriately to 'stock' first then raise them.
    It seems with this board because it has the several different methods to OC that some voltages cannot be adjusted properly so they are already preset to certain stable measures pre-thinking someone will OC.
    This not good.  Since if the Processor for the CPU VDDC voltage is set high the VCORE get hot quick.
    So, I'm asking for the correct stock voltages for the above for this 955 Black Edition CPU RB-C3 125w/TDP
    on this MSI 785GM-E65 Board.  Don't care about OC at the moment. 
    I need to know from MSI what the stock voltages are for Each Option.
    Lastly, the NB Chipset voltage is set at 1.3v from the Factory along with the HT Link.  When I lower the HT to 1.2 the SB voltage activates and these two move in unison. Which is very uncool and odd.

  • Help please - 785GM-E65 return from RMA but still KO..

    HI,
    my 785gm-e65 was broken after the m-flash use.
    no POST at all.
    RAM, 1 month then came back this morning.
    i put the sempron with its rad, the ddr3 and the power switch, then the VGA plug, and ....
    no POST ...
    clearing CMOS without power plug did not help.
    so my question is, may be its not my mobo, but to debug, i need to know what are the minimal things to POST.
    should i have POST without CPU and RAM, only keyboard and VGA plugged ?
    i tried this and nothing..
    HELP me solving this problem, before calling again the seller..
    [comment removed]

    ok, that's what i thought :
    CPU+RAM+IGP+power on mobo+power switch
    specs:
    sempron140
    DDR3 noname
    antec NSK1480 with PSU
    the thing is that everything was working before M-flash, and after that i RMA my mobo
    it's coming back and they told it's fully functional...
    but still not working, so it's hard to believe that my CPU or RAM is defective, because they were working without trouble..

  • Slow Upgrade to 785GM-E65

    Hi,
    I am interested in migrating my current HTPC (Asus M2A-VM HDMI) to the 785GM-E65 motherboard. I want to take advantage of some existing components however, as I don't want to absorb the expense all at once. I've read various online reviews and have gotten some conflicting data. My questions:
    Is this mobo compatible with AM2+ CPUs? I want to use a Phenom X4 9750 for now, and move to an Athlon II X3/4 at a later time
    Can I use DDR2 800Mhz memory with this unit? Again, with this notion of moving to DDR3 in the future.
    Thanks!

    No, the board only takes AM3 CPU and DDR3 memory.
    http://eu.msi.com/index.php?func=prodmbspec&maincat_no=1&cat2_no=&cat3_no=&prod_no=1864
    To reuse parts you need to take an AM2+ (AM3 ready) board with DDR2 slots.
    Then you cvan use AM2(+) and AM3 CPU's, but not DDR3 memory.
    If you goto an AM3 board you have to move all of it now.
    Else go AM2+ board and you can use an AM3 CPU in it later (if the board is AM3 ready)
    See a sample of such a board: http://eu.msi.com/index.php?func=proddesc&maincat_no=1&prod_no=1642

  • Can I upgrade my HP ENVY 14 DR DRE Laptop to a blueray and SSD drive?

    HI all,
    Can I upgrade my HP ENVY 14 DR DRE Laptop to a blue ray and SSD drive?
    cheers

    You can upgrade from HDD to SSD drive, but will not recommend it as it will void the warranty on the unit.
    Pertaining to  bluray drive, you might have some compatibility issues unless you find the right model.
    Although I am an HP Employee, I am speaking for myself and not for HP.
    Make it easier for other people to find solutions, by marking my answer “Accept as Solution” if it solves your problem.

  • MSI 785GM-E51 and memory modules problems

     
    Could anyone help me with one problem. I have motherboard MSI 785GM-E51 and 4 memory modules GOODRAM GR 1333D364L9/2G. But when I'm inserting ALL modules my system not starting (even POST procedure). So working variants - when I'm inserting:
    - one module in first (boot) slot
    or
    - they inserted in first and third memory slots
    Any ideas?

    It is not motherboard problem, but processor itself - I have AMD Phenom II X4 965 Black Edition 3,4 Ghz Core Revision C2 and this revision (according to the article: http://www.fcenter.ru/online.shtml?articles/hardware/processors/27650#02) has problems with support memory modules DDR3-1333 Mhz more than 2 modules. Conclusion - either adjust BIOS settings concerning memory timings and memory controller voltage or replace this kind of processor with the same type but with core revision C3

  • Upgrading RAM and SSD on MacBook Pro 15" mid 2009

    Hey,
    I want to upgrade RAM and SSD on my macbook pro, identifier 5,3, and I want to make sure the parts I picked will be compatible with my Macbook.
    I'm specifically not sure about its support of 512GB.
    I thought about RAM:
    http://www.amazon.com/Crucial-PC3-8500-SODIMM-204-Pin-CT2K4G3S1067M/dp/B008LTBJF M/ref=sr_1_1?ie=UTF8&qid=1420487078&sr=8-1&keywords=DDR3+PC3-8500
    SSD:
    http://www.amazon.com/Crucial-MX100-adapter-Internal-CT512MX100SSD1/dp/B00KFAGCU M/ref=sr_1_1?ie=UTF8&qid=1420486598&sr=8-1&keywords=CT512MX100SSD1
    Thanks!

    " I have also created a back up on Time Machine (I think I did)."
    Check this out:
    http://macintoshhowto.com/repair/back-up-computer.html
    Once you think you've done it correctly restart and hold down the option key or go to "System Preferences" under the Apple and look at "Startup Disk".
    That will tell which Disks are bootable.
    Now about that Crucial drive:
    http://forum.crucial.com/t5/Crucial-SSDs/512GB-M4-and-2009-Macbook-Pro/td-p/7805 6
    It's not clear to me that this issue was resolved. The last post goes nowhere!
    I always use OWC:
    http://eshop.macsales.com/shop/SSD/OWC
    Just did two including this MacBook Pro early 2011 13" and a 2012 Mini. Total no-brainer! The way I like it.

  • Satellite R630-155 - Fan is too noisy and SSD upgrade

    I am the owner of a Toshiba Satellite R630-155 (Core i5-480). My problems are:
    1. The fan is too noisy and never stops. In normal operation (browsing and general office work) there is a constant high pitch noise that is audible three to four meters away in an office environment - in high load you just can't stand it!!! The fan never stops... even when you are doing nothing...
    2. Heat is a big problem. The bottom of the laptop is constantly overheating and i have to place it on my desk in a way that the bottom left corner is outside of the table so it can breath fresh air from below - if not, the temperature rises and the (loud) fan is unable to keep up. When i work with the laptop while sitting on a sofa, i have to place a thick book between the laptop and my legs. The book must be thick (more than an inch) with hard covers, otherwise the heat passes through the book!!!!
    3. Last (but not least, i just mention the biggest problems here) it's the problem with SSD installation. I bought a used Corsair F80 (80Gb SSD) from a friend, but i was unable to use it with the Toshiba - the BIOS was not detecting the disk. I tried installing all latest firmware updates for both laptop and SSD but i had no success. Then i gave the disk back and i bought a brand new Zalman 128Gb SSD (SSD0128N1 Sandforce) but i had exactly the same problem. I contacted my local Toshiba support and after a lot of conversation the only answer i got is that the laptop is not compatible with those SSD's and this is acceptable by Toshiba and not their problem. They told me that if i need an SSD upgrade i can only go for the Toshiba SSD that is installed on the portege series, which is sold by Toshiba for a ridiculously expensive price - about $500 for 128Gb. I contacted the European support center and i got the exact same reply. I searched on the Internet and i found someone else with the exact same problem with a Corsair 128Gb SSD - he found that the laptop detects the SSD after ten to twenty reboots. I tried that and it was true - after a lot of reboots the laptop detected the Zalman disk and i was able to install Windows 7 successfully, but the process is unacceptable. Also the disk is benchmarked by official sites at the speed of an OCZ Vertex 2 128Gb (and slightly better), but when i ran a benchmark in the Toshiba, the results I got were below half of the advertised speed. Same benchmark in another machine for the same disk, resulted in the advertised speeds.
    Shame for Toshiba... nice design and portability but everything else is a big flaw. Their support in non existent and they do not value their customers. I feel they stole my money and I'll never buy a Toshiba laptop again.
    Sorry for the big message, but I need I have to warn potential customers. Can someone help me with any of the above problems? Do you have the same problems too?
    To be continued...

    Hi buddy,
    Regarding the fan and heat issue: Did you make BIOS update? Friend of me has Satellite R630 too and he told me that fan activity with new BIOS version 2.10 is reduced. Furthermore the notebook is cooler than before so I would recommend installing this update. You can download the BIOS update here:
    http://eu.computers.toshiba-europe.com > Support & Downloads > Download Drivers
    But before you start the BIOS update you should consider the following tips:
    -Run update as Administrator only
    -Unzip all files from zip archive before you start the update file
    -Close all running programs and also the antivirus and firewall
    -Make sure that battery is fully charged
    Regarding the SSDs its always a little bit complicated installing 3rd party products and nobody can guarantee that such parts would work. You are always on safely side with original Toshiba spare parts.
    Everything what you can do is installing the newest firmware for SSD and hope that it works but who knows maybe the BIOS update will also help you in this case ;)

  • [Q] dual HD partitioning with sata and SSD

    I have a computer that has a 500gb sata drive and a 16gb solid state drive. the computer only boots from the sata and I was wondering if I could partition the drives so that arch boots from the sata but the arch installation is on the solid state drive.

    teateawhy wrote:
    If you run
    lsblk
    are the SSD and the HDD shown as separate devices? Or is it a HDD that uses a SSD as its cache?
    If HDD and SSD are separate devices, what you want is possible. Otherwise i can't say, probably not.
    they are separate drives

  • E65 and BT headset

    I bougt E65 smatphone, everything seems great with it, exept one thing. When I connect my Logitech Freedom Hedset and NextLink Bluespoon AX2 on it it drops volume to the minimum, so every time I have to put it to maximum manually on headset...
    Another thing when you answer the call using the headset, first second you hear callr's voys on max. level and than it drops to minimum... Pretty annoying, especially when you drive. Enyone have the solution for theese probelms? Also it is not possible to chenge volume of a headset from the phone itself...
    Theese headsets were working properly on my old Nokia 6230i, so i suppose they are not broken or anything.

    I have the same problem with my E65 and both of my Logitech Freedom headsets (versions 5 and 8). Although the volume problem is annoying, there is a more serious problem where after a while you hear the other party very loud and distorted, while the other party does not hear you at all anymore. Only way to solve this is to reboot (switch off and on) the phone. The headsets work perfectly on my 2 other Nokia phones, one 6021 and one other I don't remember the model number.
    My only resolution is to buy a new headset, any recommendations for troublefree use?

  • E65 and what router

    hi first time poster long time reader so please be nice
    I have an E65 and i'm trying to get the internet telephone to work
    Location: UK
    Connection is : Virgin 20MB
    current router : Netgear WPN 824v2 wireless router(latest firmware)
    my problem is i can connect to the wireless network and surf the net no problem , but as soon as i try to make a net call it crashes the router , i use Ubuntu and ekiga on both wired and wireless , my thought is the phone is just not compatible with the netgear.
    So oh great and wise Nokia forum Guru's what routers do you use that is know to work with an E65
    min router requirements are :
    Cable
    4 port lan
    wireless
    i'm looking at the Linksys: WRT300N " The incredible speed of Wireless-N makes it ideal for media-centric applications like streaming video, gaming, and Voice over IP telephony"
    over to the forum and thanks for all help advice given

    This is what i got back from Netgear Support
    WPN824v2 is a home class router and does not have any specific support for Session Initiation Protocol or a H.323 gateway. The unit was not designed for use with a SIP phone in mind and may not work with it.
    You can try a firmware update or a downgrade.
    Version 2.0.10 ( North America and Worldwide Versions) Nov 15, 2006
    Version 2.0.6_1.2.17 ( for use in North America only ) Sep 1, 2006
    Version 1.0.20 ( for use only in Europe ) May 25, 2006
    Version 1.0.19 Mar. 10, 2006
    Initial Release 1.0.1 Jan. 3, 2006
    It may also be necessary to DMZ the IP address of the phone and or disable the SPI firewall.
    Assign a static IP address to the phone if able and then place that IP address of the phone in the DMZ option located under Advanced, WAN Setup.
    OR
    Enable port forwarding to the below listed ports.
    Port 5060 TCP and UDP
    Port 5004 UDP
    Port 10000 UDP (sipgate Stun service - usually 3478/9)
    Ports 16348-32768 UDP (RTP, RTCP multimedia streaming)
    STUN normally operates on TCP and UDP port 3478
    Or what ever ports are specified by the provider.
    Note: The DMZ or port forwarding can be used but no both setup to the same IP address at the same time.
    You may also want to review the below listed web site for a work around using SSH.
    http://www.fonosip.com/english/trouble.html
    Please not the WPN824v2 is end of life and no longer manufactured and more then likely there will be no further firmware updates.
    Thank you for choosing NETGEAR.
    has anyone found a router that works with the E65 ???

  • E65 and Bluetooth intermittent freeze up on phone

    Hi Guys
    Thanks for taking the time to respond:
    I have an E65 and PC suite at home and office (Toshiba and Bluesoleil). This works well 80% of the time. It's not set to sync auto.
    Often the Bluetooth on the phone freezes in connected mode and the only way to get it going is to switch bluetooth off on the phone and on again. It’s flashed to the latest firmware to no avail.
    I've set the phone to Bluetooth - hidden and this doesn’t make much difference either.
    The nasty is that when it freezes like this it causes the battery to drain rapidly and will prob have me die early because of the continuous radiation!
    Any advice is much appreciated.

    could also be an issue with short bluetooth range of the phone or headsets
    at least it would break up like that if range was an issue

  • E65 and BH-214

    I should like know the compatibility between my phone E65 and blue tooth BH-214, tks 

    On which device is the call key  not working ?
    If this post answers your question, you can help others by clicking the green accepted solution' button.
    Please ask your questions to the main board and not to my mailbox. Thank you.

Maybe you are looking for