785GTM-E45 mobo: no ACC option in BIOS

Hi.
I've got new mobo, installed it and can't see "Advanced Core Calibration" option in BIOS though it should be there as it's shown in manual right below "AC Firmware" option of Cell Menu.
Bios v. 8.0 the latest. Before that there was another older ver. of 8.0 - i've upgraded it but nothing has changed.
CPU - Athlon x2 3800+
Please advice.
Thx

You could have read the manual:
Quote
Advanced Clock Calibration
This item is for overclock. Setting to [Enabled] allows you to set the CPU Ratio higher.
It is available only when the processor supports this function.
http://www.msi.com/index.php?func=downloadfile&dno=9939&type=manual page 3-19

Similar Messages

785GTM-E45 MOBO BIOS V 8.80 RANDOMLY RESETS BOOT SEQUENCE

785GTM-E45 MOBO W/ PHENOM 9750 QUAD CORE CPU/4 GB WINTEC DDR2 PC6400 (2 x 2 GB) / WINDOWS XP SP3
PROBLEM: BIOS V 8.80 RANDOMLY RESETS BOOT SEQUENCE
I HAVE 4 HARD DRIVES (2 SATA II - 1 USB 2.0 1 USB 3.0) ALL OF WHICH HAVE MULTIPLE PARTITIONS WITH 1 ACTIVE ON EACH DRIVE
SATA II DRIVES / DEVICES:
ON SATA 1: HITACHI 1TB SATA II DRIVE
ON SATA 2: MSI DVD-CW RW
ON SATA 3: MAXTOR 320GB SATA II DRIVE
USB DRIVES:
1. SEAGATE FREE AGENT EXTERNAL USB 2.0 1TB HD
2. FANTOM EXTERNAL USB 3.0 2TB HD (VIA DIABLOTEK USB 3.0 PCI-E CARD)
EXPLANATION OF PROBLEM AND FIXES ATTEMPTED TO DATE
IN BIOS BOOT SEQUENCE I SELECT THE HITACHI HD AS 1ST DEVICE AND ALSO SET IT 2ND 3RD AND 4TH AND BOOT OTHER DEVICE DISABLED. SAVE/EXIT BIOS AND WHEN SYSTEM REBOOTS IT RANDOMLY SELECTS ANY OF THE 4 DRIVES TO BOOT FROM. WHEN I ENTER BIOS AGAIN IT SHOWS WHATEVER DRIVE IT HAD SELECTED TO BOOT FROM AS 1ST, 2ND, 3RD AND 4TH DEVICE. ENABLING OR DISABLING BOOT FROM OTHER DEVICE MAKES NO DIFFERENCE.
ORIGINALLY MY HITACHI WAS ON SATA 3 AND THE MAXTOR ON SATA 1 - I SWITCHED THESE AND NO DIFFERENCE. BIOS SWITCHES BOOT DEVICE NOT ONLY TO THE MAXTOR SATA DRIVE BUT ALSO TO THE USB DRIVES. USUALLY WHEN I REENTER BIOS AND CHANGE THE BOOT SEQUENCE BACK FROM WHATEVER HD IT SHOWS TO THE HITACHI IT WILL USUALLY THEN BOOT FROM THE HITACHI SOMETIMES THOUGH IT TAKES 2 OR 3 TRIES TO GET IT TO BOOT FROM THE DRIVE I HAVE SELECTED AS 1ST BOOT DEVICE.
I HAVE TESTED ALL DRIVES EXTENSIVELY USING ONTRACK EASY RECOVERY PROFESSIONAL SOFTWARE AND ALL DRIVES SHOW NO PROBLEM.
MSI LIVE UPDATE 5 REPORTS THAT THE BIOS IS 8.80 HOWEVER IT ALSO SHOWS MY OS AS WINDOWS 2000 WHICH IS INCORRECT. MY CURRENT OS IS WINDOWS XP SP3. MY XP INSTALLATION WAS AN UPGRADE FROM WINDOWS 2000.
PROBLEM IS NOT DEVASTATING JUST ANNOYING IF ANYONE KNOWS OF A FIX I'D LOVE TO HEAR ABOUT IT. IF THIS IS A BUG IN THIS VERSION OF THE MOBO BIOS I SURE HOPE THEY EXTERMINATE IT AND RELEASE AN UPDATED VERSION IN THE NEAR FUTURE.

Quote from: Bas on 26-August-11, 18:07:03
How do you know it's randomly booting a different drive?
What are the messages you get?
As this:
That looks like a broken drive to me, where it can't find the bootsector/mbr in time to boot from, so the BIOS moves to the next drive and tries again.
I built this box about 2 months ago or so and this is the version of BIOS that came with the MOBO. I have not flashed the bios in this board.
As for knowing that it is randomly booting from a different drive as I stated each of my 4 drives has at a minimum 1 active partition. The Hitachi has a dual boot setup in Windows and if it is booting from the Hitachi drive I will get the Window giving me a choice of booting from either the Hitachi or the Seagate. If I select the Hitachi I also have it setup for two hardware profiles so it then gives me that screen to select profile 1 or 2. If I get these screens no problem - I select the Hitachi and profile 1 and it boots without any further problem.
If it has switched lets say to the maxtor (remember I have selected the Hitachi as 1st, 2nd, 3rd and 4th for boot sequence and the boot from other device is NO) I get no multi boot option it just automatically starts Windows from the active partition on the MAXTOR (I can tell because the last time I used the Maxtor didn't shut down Windows properly so I get the option screen to boot normally or use safe mode etc). The active partition on the Maxtor is a duplicate of the Hitachi but about 2 months old - basically a backup of the Hitachi active partition but out of date and without the multi boot option.
In addition if it has switched boot drives and I hit my reset button and del to open up bios again and go to the boot sequence menu it will no longer show my hitachi as all 4 choices but sometimes it will show all 4 drives in varying order (including the hitachi but not as first device), sometimes 1 drive in all 4 (as in the seagate or the maxtor or the fantom drive in all 4 of the boot sequences) this seems to occur randomly and each time the list of boot sequence is different.
Keeping in mind that I had initially selected the Hitachi drive in all 4 of the boot sequences and selected NO to boot from other device - If the Hitachi drive was not ready or had a bad bootsector/mbr should I not get a message similar to "cannot boot from selected device so and so is missing etc?? I was under the impression that when one disabled the boot from other device as in NO then the bios should not attempt to go any further then attempting to boot from the selected device(s)????
As for the broken drive and bios moving to the next drive and trying again I could understand that 1. If I had not supposedly disabled its ability to do that 2. I could perhaps understand this going to the next drive if I had selected the Seagate USB drive as my initial drive because of it's so called sleep mode which I have now turned off as it was causing errors in windows. In addition I have run numerous and rigorous tests on the drives and they all passed with flying colors.
Yesterday after a couple of tries I booted from the Hitachi drive (it was listed as 1,2,3,and 4 in bios and the boot from other device was NO) and was using that all day and was on it when I posted my help request here. Shortly thereafter I properly shut down my computer. Now I would think that when I turned it on again this morning the BIOS would have maintained its previous settings of the Hitachi in all 4 of the boot sequences and the No on enabling it to boot from other device? However when I booted up again this morning it tried to boot from the Maxtor (I can tell because I get the option screen to boot normally or use safe mode etc) so I hit the reset button and then entered bios and boot sequence and now it showed the Seagate as 1 (it had just tried to boot from the Maxtor when I hit the reset button), the Fantom as 2, the Maxtor as 3 and the Hitachi as 4 and boot from other device still said NO - changed them once again to show the Hitachi in all 4 positions and exited bios and it did then boot from the Hitachi and here I am writing this message using Windows XP located in the active partition of my Hitachi drive.
I'm not exactly a novice as my computer experience goes all the way back to mainframe days of the IBM 360 series computers. I have built so many boxes I have lost count including numerous one using MSI mobos and I have never encountered a problem similar to this. As I said it is not devastating just annoying - the only thing I can think of to totally eliminate the possibility of it being the mbr/bootsector of the Hitachi drive is to back up the drive and rewrite those sectors even though no errors have been reported.
I could be wrong but after messing with this for sometime it really seems to be a bios bug or perhaps just my bios is defective - I was able to dl a copy of v8.8 from another post in the forums - and have not used it yet. Sent all of this info in a Tech support request and posted it here to see if there were any solutions I may have overlooked before flashing the bios with a dl copy of the same version I have installed.
As for downloading the current v of bios from the forums here it was apparently the only way I could get a copy as Liveupdate 5 shows that I have the current version installed and only gives me a message that my mobo bios is current and no download is needed or something like that and the MSI site no longer gives one the ability to download the mobo bios without using liveupdate 5 or at least I couldn't find one. Guess they got tired of people killing their boards with bad flashes.

785GTM-E45 mobo: Q'n'C is enabled but CPU fan doesn't slow down

Q'n'C is on, CPU clock is down when idle but CPU fan rotates on full and makes noise. Bios fan settings cannot do anything to slowdown the fan.
Tried two coolers with same result. All coolers were with 3pin connectors while there is 4-pin jack on mobo. Bios has been updated - no result.
Any ideas?
Thank you

"Fan Power Connectors: CPUFAN1, SYSFAN1
The fan power connectors support system cooling fan with +12V. When connecting the
wire to the connectors, always note that the red wire is the positive and should be connected
to the +12V; the black wire is Ground and should be connected to GND. If the
mainboard has a System Hardware Monitor chipset on-board, you must use a specially
designed fan with speed sensor to take advantage of the CPU fan control.
Please refer to the recommended CPU fans at processor’s official website or consult
the vendors for proper CPU cooling fan.
CPUFAN1 supports fan control. You can install Dual Core Center utility that will automatically
control the CPU fan speed according to the actual CPU temperature.
Fan cooler set with 3 or 4 pins power connector are both available for CPUFAN1.
SYSFAN1 support fan control, too. You may select how percentage of speed for the
SYSFAN1 in BIOS." P2-12
"CPU Smart FAN Target
The mainboard provides the Smart Fan function which can control the CPU fan speed
automatically depending on the current temperature to keep it with in a specific range.
You can enable a fan target value here. If the current CPU fan temperature reaches to
the target value, the smart fan function will be activated. It provides several sections to
speed up for cooling down automatically.
PC Health Status
CPU/ System Temperature, CPU FAN/ SYS FAN 1 Speed, CPU Vcore, 3.3V, 5V,
12V
These items display the current status of all of the monitored hardware devices/components
such as CPU voltage, temperatures and all fans’ speeds." P3-15
Do n o t use other monitoring and fan controlling programs at the same time. There must be something the matter with the fan cable or the processor seating. 3 pins have been enough for fan control since before 2000, and as you notice on the processor fan connection, you can choose between 3 and 4 pin fan connection. Pretty silly to have such a choice if 3 pins wouldn't work.
- Heck, even the photos in the manual displays a three pin '!

785gtm-e45 cpu temperature very hot

hi, i just bought a 785gtm-e45 mobo yesterday (upgraded from a 780g chipset).. After installation,i turned on the pc and noticed the cpu fan being very noisy. i went to the bios and saw my cpu temp hitting 58-60 degrees (reason why the fan is very noisy). my processor is phenom II x2 550. i want to know if this is a normal behavior of the msi mobo before i continue installing an OS. because as far as i know,58-60 degrees is very hot (without any OC) and the recent mobo i had does not even come close to these numbers no matter how much i overclock it. i presume that it has defect, that's why im afraid to go further that could possibly do damage to other components.

ok, tnx for the reply.. i managed to install windows 7 with no problems and cpu temp goes down to 45-50 degrees in windows. but i observed that when i keep on staying in the bios, cpu temp keeps on getting higher and higher up to 60 degrees. also, the cpu locks when i enter the CPU specifications. is this normal?? my 550 was bought 2 months ago (new out of the box). the only thing i bought yesterday was this msi mobo. i bought it because of ACC. im asking these questions because im very surprised with the big difference in temps with my previous mobo to this new one. with the previous one, i managed to overclock my 550 to 3.6ghz (stable) and temperature doesn't even reach 45 degrees (even at a hot weather).

MSI 785GTM-E45 BIOS CPU fan voltage control

Hello MSI gurus,
I've replaced the MB in an older HP media center with the MSI 785GTM-E45 running BIOS V8.8 out of the box.
CPU = Athlon 64 X2 4200+
My problem is the stock CPU fan has a 3 pin connection (voltage controlled) and is running at 100% speed all the time. From what I've read on the forums there are a number of people that have this issue (with other MBs with 4 pin cpu fan headers) and don't want to switch to a 4 pin CPU fan (PWM controlled). I am in the same situation.
I am hoping that there is a BIOS for this board that has an option to switch to or enable voltage control on the CPU fan header.
I have tried enabling the CPU smart fan target but no matter what settings I chose the fan remains at 100%. The H/W monitor of the MB indicates a CPU temperature (33C) well below the target (tried all options from 40C to 60C in 5C increments).
I have tried MSI's dual core center and it had no effect on the fan speed.
I have tried the 3rd party freeware SpeedFan and if had no effect on the fan speed.
I am not able to check if I have the latest BIOS or even find changelogs for existing BIOS verions because MSI seems to only direct BIOS downloads for this product to the Live update application. I have installed the live update program and it indicated V8.8 was the most recent veriosn of the BIOS for this board, although I have seen posts indicating the Live Update application is not to be trusted.
Dual core center, SpeedFan, and Live Update have all now been uninstalled.
I know the fan I'm using will change speed because I can connect a 3 pin fan controller and manually dial down the speed.
I know the BIOS can read the fan speed becase it correctly shows the RPM changes when I use the hardware fan controller.
Can anyone direct me to a BIOS version for this board (or some secret keystroke) that enables automated 3 pin voltage control on the CPU fan header?
Thanks in advance for your time.

For those who are interested I received the following answer from MSI technical support. Personally I find this to be a flaw in this board's design. I chose this MB to replace a dead MB in a HP media center for a friend. If I was buying this board for myself I likely would be using it as a HTPC because of the mATX form factor, HDMI on board, and backward compatibility for CPUs. However, due to the added cost of purchasing a new heat sink and fan I would be RMAing if I had bought it for myself. Considering many of the top performing after market coolers still come with a 3 pin fan it was a poor decision for MSI to not include support for automatic speed control of a 3 pin voltage controlled fan.
Quote
Dear Sir/Madam,
Thanks for contacting msi technical support team!
We are sorry that because of the circuit designs,we could not add cpu smart function for 3 pin's connector fan in the BIOS. The difference between 3pins and 4pins is that the second has a temperature controller but the first does not.We would suggest you utilize a 4-pin CPU Fan in order to control the CPU Fan speed.
Sorry for any inconvenience caused you!
Best regards,
MSI Technical Support Team

MSI 785GTM-E45 Bios Startup Random Freezes Help?

Hi all,
I hope I am posting this in the right forum, because it is a bios startup problem. I have been searching the forums from here and other places extensively for the past few days as well as trying pinpoint the problem on my own computer. My problem is every now and then when I boot up, it takes a really long time to get past or freezes at "initializing usb controllers" or it just freezes on "hypertransport flood sync." Some people say its the cpu, motherboard, ram, etc... So I have just been testing to see which component is causing the problem.
I recently purchased parts to build a new computer from frys. The parts are:
1. MSI 785GTM-E45
2. AMD Phenom II X2 555 BE
3. Patriot Extreme Performance 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 800 (PC2 6400) Dual Channel Kit Desktop Memory Model PDC24G6400ELK
4. Antec EarthWatts Green EA-430D Green 430W power supply
5. PNY Geforce 240 GT
6. 80 gb pata WD harddrive and NEC pata dvd-rw.
At first I thought it might've been that I was unlocking the cores and they were unstable, turns out the 4th core is unstable. However, I still get the weird freezes at initializing usb controllers and hypertransport flood sync even when I am running the stock 2 cores. Plus I purchased another AMD 555 to test it out, and its the same. Then I turned my attention to the ram, I ran memtest86+ on it and the ram appears to be good. And I don't think it is the power supply either, I can't really test it cuz I only have one. It can't be the video card because I was having this problem before I even installed the video card (I was using onboard waiting for something to go on sale). I am beginning to suspect that it's just a bad motherboard. I have even tried updating the bios to 8.5, I can now support X6, but it still doing the weird random freezes.
Was wondering if others had any ideas or suggestions. Thanks.

For your current system as is that PSU will be OK. If you think you will be upgrading video to something beyond a 250GTS & x4 CPU then I would recommend the TX650W instead. newegg usually has the best prices for the Corsairs and only online store I buy from in the past couple of years.
If you look at the specs at newegg you will see where it says how many rails it has. Also n'egg usually has picture of the PSU label and you can see there, it will show for example 2 rail: +12V1@18, +12V2@18, note the number after +12V. A single rail will have 1, for example the Corsair in your link +12V@30A

785GTM-E45 not POSTing after a week (Need help)

Hello guys and girls,
Good day to you.
I am new here as I just happily purchase my new MSI motherboard last week. Yay~
However, I am now currently facing problem in POSTing the PC after it was working beautifully for a week. Hope someone can help me as I have exhausted my testing/diagnostics options.
Some other infos that might be informative :-
1.) APS LED does not light anymore.
2.) No longer have successful POST beep anymore. (CPU Cooler comes on though)
3.) Of course the black screen.
4.) The last boot time, I remember seeing CMOS related error in the POST screen. After that loaded into Windows XP 32bit and I restarted the PC. Then the No POST happened.
My PC hardware components :-
CPU: Athlon X2 5000 (2.2GHz)
Motherboard: MSI 785GTM-E45 (ver 1.4) (No idea on how to check the BIOS as I can't even POST now)
RAM: I have 4 units working memory that I have tested to be working in this motherboard before it is not POSTing.
a.) Kingston DDR2 667MHz (KVR667D2N5/2G) [1 Stick]
b.) Mushkin DDR2 800MHz [1 Stick]
c.) Corsair Dominator DDR2 1066MHz 2x1GB Kit [2 Sticks] (using this one as the main before it failed to POST)
Graphics: Using onboard
PSU: Seasonic S12D 750W
a.) +3.3V = 24A ; +5V = 30A. (150W)
b.) +12V Combine = 62A (744W)
c.) -12V = 0.8A (9.6W)
d.) +5Vsb = 3A (15W)
Diagnostics that I have done :-
1.) Checked whether the motherboard is touching the casing which will ground it. The motherboard is screwed on the standoffs with a 1.5cm away from the case. Checked the motherboard edges, not touching the casing either. Checked whether is there any screws that are short-circuiting the motherboard, nothing there as well.
2.) Unplug the HDD and ODD. No POST as well. Plugged the HDD and ODD to another computer, it works.
3.) Triple checked the power connections in the PC. No POST. After that plugged my Seasonic PSU to another computer to test. It was working.
4.) Plugged another working PSU (Xigmatek 550W) from a working PC. Quadruple check the power connections is correct. No POST still.
5.) Test the memory DIMMs with different slots (all 4 of them). Installed one at a time and each time is in different slot. No POST still. Tried the board with NO memory, it beeps non-stop (Good news it is still working?)
6.) Did the Clear CMOS method according to manual. No POST still.
7.) Checked the monitor by plugging into another computer and see whether is it faulty. Is working.
8.) Retest all the memory DIMMs in another PC. All 4 DIMMs is working in another PC.
9.) Carefully remove the CPU and reseat the processor. After that retest all the 4 memory DIMMS (No matter which slot). No POST still.
10.) Disassemble the motherboard from the casing and other components to checked whether the capacitors are bad. Didn't detect any.
11.) Plugged in a working graphic card to check whether the onboard graphic is faulty. No POST still.
So now, I think I am left with 2 possibilities. The processor or the motherboard, however, the motherboard was the one showing symptoms based on the LED thing. So I am siding towards the motherboard is faulty?
I am out of ideas now. Hope someone can help me.

Yes, the CPU power is connected. both the 4 pins and 24 pins.
Some updates, I went to buy a Sempron 140 processor to test just for the sake whether the mobo works.. I just burnt some money on it.. it won't work.. Brought the motherboard back to the shop, they tested it and it is faulty.. so warranty claim. Guess I wont have a mobo for sometime..
Consider solved and I just burnt some money buying a spare proc which I think I wont be using also. haha.
Thanks for everyone who attempted to help me.

MSI 785GTM-E45 Strange Problems

I hope this is the correct fouum, but here goes.
I have a new 785GTM-E45 with an AMD Athelon IIx2 255 dual core processor, 4 MB RAM, running XP Pro SP3.
I am having more halts, stops, freezes, what ever you call it than I think I should be having. Very frequently if I read an email then try to connect to a link, the machine freezes and after a CTRL-ALT-DEL the message "This program not responding."
There are freezes at other random times also but I am unable to duplicate or find a pattern. I have used XP PRO for a long time on previous platforms and this behavior is unusual, hence this call for help.
Possible Problem areas
CPU
RAM
Internal Motherboard
Possible need to update BIOS ? I keep reading info that suggests this can produce strange problems but I have not updated this until I know more about what problems this can cause and until you guys assure me that I can do this without causing more problems.
Is there any way to check CPU and/or RAM? I really do not want to spend a lot of money but are there any freebys out there that can test these two items?
Any other ideas about this MB that might be causing this trouble?
TYA
John

John,
I have the same board but on it I have
PSU Antec 500Watt
Phenom x3 8400B2 with TLB bug
2GB Samsung 667MHz
Geforce 9600GT 6pin molex
Windows Vista 32
Sata HD
Sata DVD ROM
and no freezes.
The Bios is latest 8.5
Running the FSB at 203MHz so three steps from 200MHz
Also running Defaults in Bios doesn't always turn out good to best results.
Turn off C1E in the CPU Options under Advanced
Turn off Spreadspectrum in Cell Menu
Turn off all unnecessary ports such as LTP ports these are parallel/serial ports
Also, do not turn on the ACC and all those options without first consulting and having your system running top notch.
If you're not using Firewire turn off the 1394 option or disable (turn off means disable) if the selections are Auto leave them on Auto, the board will detect and turn on if associated in this case the device is present.

785GTM-E45 and the disappearing video controller

Noticed an odd behavior on my 785GTM-E45 motherboard. When there is no video card installed on the motherboard, the onboard video works.
I have since installed an ATI Radeon HD 4350 board, and I can no longer use the video ports on the motherboard. Hardware info only shows one adapter.
I was hoping to use three or four monitors with this setup, but as of yet no dice.
I have tried both Internal and PCI-E for the primary video setting in the BIOS, but that doesn't seem to change anything.
Anyone know why this is? Thanks!

+1.
I have a G45 Asus mobo, and the only thing I can do when a videcard is installed is choosing between internal (and the videocard doesn't work) or pcie (and the internal doesn't work). Before, I had an old G31 Gigabyte motherboard, and I was able to use both internal and pcie at the same time. Maybe some nvidia 9300/9400 boards too. I never tried a pcie card with my 890GXM-G65, don't think it will work.
What you can do, since you only have an HD4350, is to plug it in the pcie 1x port...you'll have to cut it at the end (quite easy with a cutter, but be careful !), but normally you should be able to use both HD4350 and Internal (not too sure how the driver will react ?). You could also buy a special pcie 1x videocard (or pci).
http://forums.whirlpool.net.au/archive/1380104

785GTM-E45 AND OCZ2P10664GK PC2 8500

AMD 7850 AM2+ 4 gigs ocz memory. When I set ram to epp mode for 1066 set to 2.2v the bios post but windows will not load. I tried manually setting the memory timing but same problem. I messed around with multipliers and fsb and was able to get the system memory running stable at 1000mhz but 1066 would be nice. is there a list of supported memory that works with this board. I've noticed that no bios updates are available yet. I've also contacted ocz about this issue.
Thanks

OCZ configurator report presumes Phenom II X4.... The RAM installed is not listed for that mobo by OCZ. Everyone needs to update their configurators for the new processors...
Upgrade Configuration for: MSI
Model: MSI 785GTM-E45
System Specs
Type of system:   Motherboards
Bus Architecture:   PCI
CPU Type:   Phenom II X4
Memory Specs
Standard Memory:
Maximum Memory:   8192 MB
Memory Expansion:   2
Model Specs
Model Comments:   AMD 785G, 2600 FSB, Micro ATX
CPU Comments:   Phenom II X4
COMPATIBLE MEMORY
Description    Mfr SKU/OEM#    OCZ Technology Part No.
256MB, 667MHz, DDR2-667 PC2-5300, 240p DIMM, 1.8v
256MB, 800MHz, DDR2-800 PC2-6400, 240p DIMM, 1.8v
512MB, 1066MHz, DDR2-1066 PC2-8500, 240p DIMM, 1.8v
512MB, 667MHz, DDR2-667 PC2-5300, 240p DIMM, 1.8v
512MB, 800MHz, DDR2-800 PC2-6400, 240p DIMM, 1.8v         OCZ2800512
1GB, 1066MHz, DDR2-1066 PC2-8500, 240p DIMM, 1.8v         OCZ210661GB
1GB, 1066MHz, DDR2-1066 PC2-8500, 240p DIMM, 1.8v, double-sided
1GB, 1066MHz, DDR2-1066 PC2-8500, 240p DIMM, 1.8v, single-sided
1GB, 667MHz, DDR2-667 PC2-5300, 240p DIMM, 1.8v         OCZ26671GB
1GB, 667MHz, DDR2-667 PC2-5300, 240p DIMM, 1.8v, double-sided
1GB, 667MHz, DDR2-667 PC2-5300, 240p DIMM, 1.8v, single-sided
1GB, 800MHz, DDR2-800 PC2-6400, 240p DIMM, 1.8v         OCZ28001GB
1GB, 800MHz, DDR2-800 PC2-6400, 240p DIMM, 1.8v, double-sided
1GB, 800MHz, DDR2-800 PC2-6400, 240p DIMM, 1.8v, single-sided
2GB, 1066MHz, DDR2-1066 PC2-8500, 240p DIMM, 1.8v         OCZ210662GB
2GB, 1066MHz, DDR2-1066 PC2-8500, 240p DIMM, 1.8v, double-sided
2GB, 1066MHz, DDR2-1066 PC2-8500, 240p DIMM, 1.8v, single-sided
2GB, 667MHz, DDR2-667 PC2-5300, 240p DIMM, 1.8v         OCZ26672GB
2GB, 667MHz, DDR2-667 PC2-5300, 240p DIMM, 1.8v, double-sided
2GB, 667MHz, DDR2-667 PC2-5300, 240p DIMM, 1.8v, single-sided
2GB, 800MHz, DDR2-800 PC2-6400, 240p DIMM, 1.8v         OCZ28002GB
2GB, 800MHz, DDR2-800 PC2-6400, 240p DIMM, 1.8v, double-sided
2GB, 800MHz, DDR2-800 PC2-6400, 240p DIMM, 1.8v, single-sided
4GB, 667MHz, DDR2-667 PC2-5300, 240p DIMM, 1.8v
4GB, 800MHz, DDR2-800 PC2-6400, 240p DIMM, 1.8v         OCZ28004GB

785GTM-E45 - Half of Memory Being Recognized

MSI 785GTM-E45
AMD Phenom II 840
4GB RAM Kingston HyperX DDR2
Basically my sticks of ram are only being recognized as 1GB sticks instead of 2 GB sticks.
- I have Windows 64 Bit
- This is occuring inside the BioS this is not a software issue
- Both sticks are 100% working condition, I have tested them in other machines
- BioS is updated at version 8.8 I believe (12-2010 version)
- I have checked and unchecked all options within the BioS I feel safe trying
- This occurs with 1 stick, or 2 sticks in the slots (I only have 2 slots) they both recognized as 1GB each.
- I have made sure my RAM is indeed 2GB sticks
- I have reseated my RAM multiple times
Any help on this would be greatly appreciated. Even a arrow to a sticky post.
Thank you.

maybe your cpu is damaged? have you tried with another one?
or with different memory sticks eventually?

785GTM-e45 enable Unlock CPU Core - won't post past sata harddrive detection

I recently bought a 785GTM-E45 and have a Phenom II x2 560 in it. I have a sata harddrive drive attached with the Raid setting to AHCI. I have windows 7 x64 running fine, but wanted to see if I could unlock any cores. If I enable ACC but leave Unlock CPU Core to Disabled, I can boot fine. But when I change Unlock CPU Core to Enabled and reboot, i get the Post messages and it identifies the CPU as Phenom II X4 B60. Its goes through the whole posting until it get to initializing the sata drives. It will sit on that screen for a few minutes and then say that no drives are found so it cant boot. If i do the same thing with the harddrive unplugged, it immediately says it can't find any drives. I have tried changing the Raid setting to IDE with similar results. I am running bios version 8.8 One thing I noticed that I thought was strange is that when I do the save after enabling CPU Unlock, the computer totally shuts off. The power light turns off, all drives and fans turn off, then it turns it self back on and does the reboot. It only does this with CPU Unlock enabled.
785GTM-E45
Phenom II x2 560BE
OCZ SLI-Ready 2GB (2 x 1GB) 240-Pin DDR2 800 (PC2 6400)
Onboard video and sound
Hauppauge 2250 QAM Tuner
Hauppauge 1600 QAM Tuner
Samsung F4 HD204UI 2TB
Antec NeoHE 500W
Win 7 x64

I believe that AMD is doing a more thorough job of disabling defective cores on those things and you will not be able to unlock. We've been seeing more and more of that recently on the 5xx series. If you want more cores then you will have to pay for them, looks like no longer a free ride for extra cores. Can't blame MSI for that.

MSI 785gtm-e45 gpu overclock?? could it be??

Hi guys, I'm new in the forum. Last saturday I bougth this motherboard (MSI 785GTM-E45) and I tried to overclock the ati 4200 integrated gpu but I can't. There isn't an option in the BIOS, not even with MSI Dual Core Center, or AMD Overdrive or ATI Tray tools or ATI GPU tools... so I would like to know if this new BIOS version has te option to change the MHZ in GPU. Thanks in advance!!

Yes, that may be the case. But this is a Micro-ATX-Mainboard which simply does not have this option in BIOS. What is the point of overclocking the low-profile onboard-video chip of a mATX-Board besides increasing the chip temperature? Overclocking onboard video chips is not going to turn them into high-performance full-featured video cards either.

UVD-power summary of MSI 5770 Hawk, 5570, & 785GTM-E45; Hawk min voltage

MSI R5770 Hawk
MSI R5570-MD1G
MSI 785GTM-E45
GPU PWR SYS f_GPU f_VRAM V_GPU set V_GPU meas Note 1: freq & voltage Note 2: system state
DCW Mhz Mhz V V
785 35 197 400 idle stock idle, light (5 min max)
785 46 498 400 UVD stock 1x 720p sharpen complex 2
5570 43 157 200 0.9 idle stock idle, light (5 min max)
5570 54 400 800 1 UVD stock 1x 720p sharpen complex 2
5570 52 400 800 0.9 0.8987 UVD undervolt/underclock 1 1x 720p sharpen complex 2
5570 55 400 800 0.9 0.9001 UVD undervolt/underclock 1 1x 1080p sharpen complex 2
5770 53 157 300 0.95 0.956 idle stock idle, light (5 min max)
5770 58 157 600 0.95 0.957 idle 2x f_VRAM idle, light (5 min max)
5770 65 157 1200 0.95 0.957 idle 4x f_VRAM (nom. max) idle, light (5 min max)
5770 61 400 900 0.95 0.958 idle @ UVD stock idle, light (5 min max)
5770 72 400 900 0.95 0.9499 UVD stock 1x 720p sharpen complex 2
5770 75 400 900 0.95 0.9508 UVD stock 1x 1080p sharpen complex 2
5770 60 157 300 0.95 0.9498 UVD undervolt/underclock 1 1x 720p sharpen complex 2
5770 63 157 300 0.95 0.9503 UVD undervolt/underclock 1 1x 1080p sharpen complex 2
5770 61 157 200 0.95 0.9497 UVD undervolt/underclock 2 1x 720p sharpen complex 2
5770 61 157 200 0.95 0.9497 UVD undervolt/underclock 2 1x 1080p sharpen complex 2
AMD Power Play states are glitchy, and not all videos detect and run with DirectX Video Acceleration. So max power during playback can end up on the highest power state which is not shown above.
MSI R5770 Hawk minimum power
The uP6204 power controller used on the MSI R5770 Hawk design nominally supports 0.5625 to 1.3500V in 0.0125V steps.
With a stock video BIOS, MSI Afterburner 1.50/1.51 allows the MSI R5770 Hawk to be soft-modded from 1.000 to 1.350V in the roughly 0.0125V steps.
The video BIOS can be set as low as 0.950V but with no steps between 0.950 and 1.000V.
MSI Afterburner 1.60 beta 4 or earlier adds the AllowCaptureVoltageDefaults profile setting. Acquiring, then changing the default GPU voltage allows "resetting" the Hawk to 0.950V in Afterburner for the highest frequency state. This allows maintaining Power Play transitions and running the max frequency at 0.950V, where Afterburner by itself is limited to 1.000V.
The max frequency state of the Hawk is 875 MHz 1200 MHz 1.200V. To have the most flexibilty on control the Hawk, lowest power in the Desktop/HTPC/light gaming, and the ability to manually overvolt/overclock for specific games: run the Hawk at 0.950V in the max frequency state.
How-to work around Afterburner and the Hawk design to run 1.000V in the max frequency state. *
1) in the video BIOS, leave the voltage as 1.200V in the BIOS--which is required for Afterburner to change the Hawk voltages in Windows
2) in the video BIOS, change the GPU frequency of that state to something less than or equal to the maximum stable frequency at 1.000V
3) in Afterburner, Reset to default settings **
4) in Afterburner, change "Core Voltage" to 1.000V
5) in Afterburner, Apply
6) in Afterburner, Save to Profile 1
7) in Afterburner, \Settings\Profiles\2D Profile\ & "3D Profile" choose "Profile 1" ***
8) on each Windows startup, run Afterburner
How-to work around Afterburner and the Hawk design to run 0.950V in the max frequency state.*
1) in the video BIOS, leave the voltage as 1.200V in the BIOS--which is required for Afterburner to change the Hawk voltages in Windows
2) in the video BIOS, change the GPU frequency of that state to something less than or equal to the maximum stable frequency at 0.950V
3) in Afterburner, confirm the voltage default setting for 0.950V--capture voltage defaults as needed using AllowCaptureVoltageDefaults mentioned above
4) in notepad as an Administrator (Win 6.x), change the Hawk's profile configuration file to 0.950V
example:
[Settings]
uP6204_Defaults=D7 20
5) in Afterburner, Reset to default settings **
6) in Afterburner, change "Core Voltage" to 1.000V--changing the profile setting to 0950/950 is not useful as of 1.60 beta 4.
7) in Afterburner, Apply
8) in Afterburner, Save to Profile 1
9) in Afterburner, \Settings\Profiles\2D Profile\ & "3D Profile" choose "Profile 1" ***
10) on each Windows startup, run Afterburner
11) in Afterburner, "Reset" to re-enable 0.950V.
* UnlockVoltageControl in the primary Afterburner profile's [Settings] will likely be needed.
** Only default profiles support Power Play states correctly.
*** Having a non-"default" profile in 3D results in the "3D Profile" activating instead of the UVD in the BIOS.
MSI Afterburner, default voltages
Profile Idle V_GPU @ V_CORE (V)
D7 12 1.125
D7 14 1.100
D7 16 1.047
D7 18 1.049
D7 19 1.037
D7 20 0.949
D7 21 0.937
D7 22 0.925
D7 23 0.912
D7 24 0.899
Power Play states in RBE 1.25
0 Boot 00 -> 00 -> 00
1 Power saving 01 -> 02 -> 00
2 UVD 03 -> 03 -> 03
3 Power saving 04 -> 02 -> 00
4 ACPI 01 -> 01 -> 01
Stock clocks & V_GPU
Clock info 00 01 02 03 04
f_GPU 875 157 600 400 400
f_RAM 1200 300 1200 900 1200
V_GPU 1.20 0.95 1.00 0.95 0.95
My current and likely final settings for MSI R5770 Hawk:
MOD clocks & V_GPU
Clock info 00 01 02 03 04
f_GPU 714 157 600 157 400
f_RAM 1200 300 600 300 600
V_GPU 1.20 0.95 0.95 0.95 0.95
Afterburner Profiles
# CoreVoltage CoreClk MemClk
1 0950 714000 1200000
2 1000 785000 1200000
3 1125 902000 1200000
5 1200 951000 1200000
More data & full system config:
http://forums.techpowerup.com/showpost.php?p=1858205&postcount=1

Radeon HD 4870 X2 2GB GDDR5 on a 785GTM-E45 mainboard post prob

trying to install my Radeon HD 4870 X2 2GB GDDR5 on my 785GTM-E45 mainboard and it wont post i disabled my internal card did every thing directions said to do. cleared my cmos still wont post. so i removed my pci e card and hooked my monitor back up to the main board and nwow that isnt posting grrrrr is there a jumper setting on my board that im not seeing to make my new card work. or how can i get my onboard vga to work agian

ok i got it to work and after about a minute running though my 650w power supply went BOOM so i went out and got a TX850 V2 power supply and it fired right up now im having a problem with hyper threading i see theres a way to adjust it in my bios just need to figure out what to adjust it to

785GTM-E45 mobo: no ACC option in BIOS

Similar Messages

Maybe you are looking for