785GTM-E45 SATAs Not Detected with RAID Set to AHCI

I have a Seagate 640GB on SATA 1 and a WD 250GB on SATA 2. These are detected and show in BIOS when RAID is set at IDE. Disappear when I set to AHCI.
Is this a defective board? Or, is there a compatability issue? I am used to Award BIOS, that has selection of AHCI under SATA mode, rather than being under the RAID options. Wondering if they vanish, because it wants matched size for RAID?
Any info would be a big help, as I don't want to blow away my AHCI drivers on the OS that have AHCI from my previous 780G board.

It is in the Basic Features Screen. SATA drives show undetected here, when AHCI is selected.
Funny and sad, that the manual's BIOS pages skip over this whole area and goes to the Cell portion. But, I think I figured out, that though it is not mentioned anywhere, that it appears that the SATA drive area under basic features, is only IDE devices.
Under Advanced Features and Boot Sequence, I found that the drives showed up and could be selected.

Similar Messages

When trying to restore volume, does not detect my raid set.

So I just bought a Mac Pro. After setting it up, I finally got my extra 320gb hd. So I back everything up with Time Machine, create a raid 0 set with two 320GB HDs, and then try to restore the machine. The problem is when I try to select the volume to restore the Time Machine HD onto, it doesn't detect my RAID set. How do I fix this?

I'm guessing you created a volume on your raid 0 set? Also, is this an issue with software raid or hardware raid, using the apple raid card?

160gb SATA not detected while 80gb SATA is working fine

I have a MSI K8MM-V board with AMD 2800+, I am alredy using a 80gb SATA1 drive, I recently purchased a 160gb SATA1 (seagate) however, to my surprise the disk is not being detected in the BIOS and even when I suply the drivers during windows xp installation, the system is not able to detect any hard disk attached, can somebody please suggest me what to do now, is my board in-compatible with disks with such high capacity
system spec:
AMD 2800+
VIA K8MM-V
512 RAM
80gb SATA(working)
160gb SATA(not detected)

Quote from: Tiresmoke on 03-June-06, 04:14:52
Surv1v0r don't be so hasty next time to RMA. Many times it is something simple like this that gets the job done.
Fair comment - sorry, you guys were right and I was wrong - no excuses.
jatin_bhasin - from Wikipedia :
SNAFU - Situation Normal: All F***ed Up
FUBAR - F***ed Up Beyond All Recognition/Repair/Reason/Redemption
Quote from: mrbadnback
I have read on WD website and on the website where I bought my WD HD and they had lots of people return the HD's just because they didn't know about the jumpers.
You do wonder whethere WD (and others) will learn anything from this. RMAs can't help anyone, perhaps a little guidance on the casing or an installation sheet would help to resolve some of these ?
Once again - sorry

Bluetooth in iPad not detecting with imac

Bluetooth in iPad not detecting with imac

http://support.apple.com/kb/HT3647?viewlocale=en_US&locale=en_US

785GTM-E45 SATA HDs not detected by W7 x64 setup

Hi, so I've not been able to install Windows 7 x64 with my two SATA drives. I have tried all three modes IDE, RAID (setting up a raid 1), ACHI and hit F6 followed by F8 at setup to allow unsigned drivers but I get a message stating that no compliant hardware was found after loading the drivers for the SATA controller.
Also, I've disabled my LAN, audio, and even my USB controller and I still get this problem. And I've tried at least 4 different versions of SATA drivers (SB7xx and SB710 ones) from here:
http://wwwd.amd.com/AMD/SReleaseF.nsf/softwarepages/DriversbyOSChipset?OpenDocument
Should I try to get a replacement board or am I doing something wrong? Thanks.

Well I've reset the CMOS, by removing the battery and clearing the jumper settings but it hasn't made any difference, as well as disabling every other component on the motherboard that I don't need, ie. everything but the IDE DVD drive and the two SATA HDDs.
Yes, both drives are detected under BIOS.
I am using two seagate hard drives which are both this drive:
http://www.newegg.com/product/product.aspx?Item=n82e16822148040
I put a live CD of Ubuntu 10.04 x86 in and it loaded just fine and it actually detected the drives--even let me format them and copy files to them! I don't understand why it works when Win7 setup can't even detect them.

785GTM-E45 SATA (AHCI) HDD and IDE DVD drive cannot be used together

I have bought 785GTM-E45, and installed a sata hdd and a IDE dvd drive on it. the sata is set to ahci mode. After install xp using f6 method and install all the drivers, I cannot find the dvd drive at all in windows. I have to go into bios to set the sata ports back to IDE model to make the dvd appear again.
Anyone knows the reason? It looks like a bios bug. I am using the new v8 bios.

Quote from: vm1 on 06-October-09, 00:12:31
It is just annoying that this board has so many issues. No vcore change, no gpu voltage change, v8 bios will freeze if entering processor details, and the issue in this current topic. I have used at least three other brands' boards and never had any issue before. Oh my, MSI...
MSI bashing is NOT allowed
>>Please read and comply with the Forum Rules.<<
You could have read the manual before buying, then you would have known it's a cheap office board.

NAS with RAID set up

I want to set up a NAS with RAID option. I have my imac (with leopard) and couple of PCs (vista) at home. I also have an xbox which i use media player (sorry no apple TV) for photos etc. Do you have any suggestion which is the best option that with support both PC and Mac. I would also like to use my NAS as my itune server and store my other media file.
I am not a digitally savvy person and am looking for a simple option.

I have been happy with the ReadyNAS line from Netgear (formerly Infrant). They have information and very active user forums where you can ask specific questions at: http://www.readynas.com

Intermittent "Camera not Detected" with D90 and Windows 7

I just installed and set up LIghtroom 4 on a Windows7 PC. We are having intermittent problems shooting tethered with a Nikon D90. We have successfully been able to tether the D90 to and capture images in Lightroom. But now we are frequently receiving the "Camera not Detected" indicator in the tethered capture window.
It seems that Windows 7 is taking control of the camera away from Lightroom. Is that possible? Is there some setting in Lightroom to override Windows?

it has to be plugged into the machine before you power on the machine, it is not hot swapable like on OSX
does the screen work in OSX

Problem with raid set on xserve

Hi to all!
I hope you can help me with a big problem that I have with a Xserve of the work.
Yesterday afternoon I come to the work and my partners mentioned to me that the web pages were not going. I tried to connect with ARD but he was not answering. I had to move to the building where the server is racked and when I connected a monitor a it was showing me a folder icon with an interrogation icon.
Since this had happened to me in my Mac of the office once, I initiated from the installation DVD to see if I could repair permissions and/or the discs with the Disk Utility. For my surprise (and terror) does not show any volume or disk except the DVD.
I got into the RAID Utility in the menu and there I could see the discs but the RAID Sets does not appear... We had mounted since we install the machine a raid 5 with 3 discs and 2 volumes on this raid set.
Then, from the Terminal, doing "diskutil list" it's show no volume on any disk.
I suppose that something has happened with the volumes and the raid cannot be mounted...
Is there any way to mount the volumes again? Something similar to the "fixmbr" that I believe that there are in others OS to restore the volumes tables...
Is there any way to mount again the RAID without losing the information from the discs?
Do you know that can be happening?
PS: It is a Xserve of the last ones, with Mac OS X 10.6.8. I have already tried to reset the PRAM and it keeps on doing the same.

The Server Monitr does say anything. It doesnt pick up any server. I tried to add the XServe in the Server Monitor, but it keeps waiting for a reply after I have put in the username, password and IP address.
It is an XServe with a Mirror software RAID on the 2 x Internal Hard Drives within the XServe
I am not using the SAN software
There have been reports of fault latchs on the Apple Drive Bay Modules. Do you think this could be causing the units to dismount?

785GTM-E45 - Will not boot

I purchased a bare bones system from Tiger Direct for a basic livingroom multimedia pc to basically run Boxee and we browsing. The kit included: MSI 785GTM-E45 DiabloTek Barebones Kit - MSI 785GTM-E45 Motherboard, AMD Phenom X4 9750 CPU, CPU Fan, Patriot 2GB DDR2 RAM, Seagate 500GB HDD, DiabloTek Elite ATX-Mid Tower Case, 450W Power Supply (Here is a link to the system: http://www.tigerdirect.com/applications/searchtools/item-Details.asp?EdpNo=500255&sku=B69-0367&SRCCODE=WEM2675N&cm_mmc=email-_-Main-_-WEM2675-_-tigeremail2675).
I have built several systems in the past and I have never had an issue before. I received everything in the mail and assembled but the system would power up for about 3 seconds then turn off - essentially the cpu fan would turn on then off immediately. After doing some troubleshooting it turned out to be a bad power supply. TD shipped me a new case and I transferred everything over and it now turned on just fine and stayed on.... BUT it would never load the bios, etc. I have cleared the cmos, reseated and double checked for extra mounting pins on the MB case, reseated the ram.. no fix. I even followed the "flow chart" here: http://www.msi.com/service/cannot-boot-up-properly/
I have unplugged everything and put the motherboard on a nonconductive surface...same result. Unplugged everything and unplugged the RAM hoping to get some system error beep.. NOTHING..ugh
The motherboard powers up, CPU fan turns on, the HDD spools up and runs but that is it. No USB ports light up, the DVD drive does not come to life and there are no system beeps and the monitor never gets any input from the motherboard. I am not running a seperate video card - just the onboard video.
What are some next steps for troubleshooting to get the system up and running?

Exactly! No beep codes at all. I unplugged everything including RAM to see if I could start troubleshooting component by component but with no beep codes. I have been swapping out RAM/HDD/removing from the case and starting it up on a non-conductive surface, you name it...no boot and no beep...

MSI H55M-E33 SATA Not Detected

I've been putting together a new computer with this H55 board fresh out of the box. No matter what I do though all my SATA ports still show up as Not Detected in my BIOS for my hard drive or disk drive. I've tried all kind of combinations with every port. I've even taken out the CMOS battery for a while.
Specs are:
MSI H55M-E33 motherboard
Intel Core i5-680 Clarkdale 3.6GHz 4MB L3 Cache
Western Digital 1.0 TB HDD Model WD1002FAEX-00Z3A0
Pioneer DVR-218LBK
Corsair 850HX Power Supply

Okay, so I cleared CMOS several times, and even tried a brand new hard drive and DVD drive with at least seven different sata cables and every sata slot I had. Still nothing showing up at all in CMOS.
Also, here's my Bios: A7587IMS V1.1 012210
I'm very new at putting computers together, but from my understanding Sata should pretty much be plug-and-play. Or at the very least plug-and-see.

MSI 785gtm-e45 usb not recognizing

HI all. i just built this pc yesterday using this mobo MSI 785gtm-e45 with AMD phenom X4 2.5ghz along side with 2ghz of ram ddr2 800mhz and installed windows 7 ultimate 32bit . everything went well thru the installation of the os, cept when i went to plug in my jump drive the lower right hand box said /!\ usb is not recognized. im using a ps/2 mouse and keyboard it connects thru the internet, i even downloaded drivers from the website and installed and still im getting that warning. any idea of wut could be the culprit

Quote from: Svet on 26-July-10, 07:10:13
>>If you are having problems with USB ports, read this topic.<<
I am having the same problems, but this is also affecting my onboard USB connections. I have disconnected the panel USB connections (they only had 8 wires anyway, so no need for the posted reply in that thread) from the mobo. I cannot even get the mobo to recognize a USB mouse plugged into a PS/2 adapter.

Upgrading Xserve with RAID set

Hi,
I have been asked to upgrade a copy of Server 10.3 to 10.4. I don't like upgrading, so will do a clean install and then restore all of the SA and WGM data back into the server. Here is the question:
The XServe has 3 bays - bay 1 has the startup disk and bay 2 and 3 have a mirrored RAID set. Is the RAID config data held in the OS, so if I reinstall the system will the configuration data for the RAID set be lost and will I have to re-RAID the server? Or is the config data stored on the drive and so a re-install won't affect the RAID set?
Many thanks,
JS
iMac G5 17" 2 Ghz, 1 GB RAM, 600 GB HDD Mac OS X (10.4.9)
iMac G5 17" 2 Ghz, 1 GB RAM, 600 GB HDD Mac OS X (10.4.9)
iMac G5 17" 2 Ghz, 1 GB RAM, 600 GB HDD Mac OS X (10.4.9)

I would like to know if the RAID 'config' data is
actually written onto the drive or is stored in the
OS. I first thought it would be stored in software
because Disk Utility uses software RAID, but then
again a single drive has the partition data on the
drive.
James,
If you think about it a bit, software RAID information has to be on the drive because the volume becomes a RAID before a filesystem is created and before an install is done. Likewise, a hardware raid is done on the interface card and comes up the same way. Neither can know which of the members of the mirror are available at first boot; otherwise, there would be a single point of failure during boot, and the whole purpose of a RAID 1 mirror would be lost.
The bootstrap starts on the mirror primary, then, as the driver is brought online and before any writes are done, the driver collects the members of the RAID 1 mirror set and forms the mirror. If the mirror primary isn't available, then the mirror secondary is used (which has an exact copy except for stuff indicating that it is the secondary). All this happens normally during boot, as if from a single non-RAID drive, until the cutover is made to RAID early in the driver intialization.
That's why booting from a RAID 0 (stripe) is so hard - all of the data is not present on a single drive. It can be done, but it is hard and requires special care during the boot.
You really do want to make the upgrade to AppleRAID 2 before spending time on the update, though. There are details in this article on afp548.com:
http://www.afp548.com/article.php?story=AppleRAID2-in-Depth
Russ
Xserve G5 2.0 GHz 2 GB RAM Mac OS X (10.4.8) Apple Hardware RAID, ATTO UL4D, Exabyte VXA-2 1x10 1u

Quickpaint reports not working with assignment set defined with criteria

Hello,
I have a problem with quickpaint reports in HRMS. When i run quickpaint report against assignment set defined with criteria it reports following error: APP-PAY-06867 An error occurred during formula execution FFX00_DATA_NOT_FOUND (assignment criteria was &ASG_LOCATION=New York).I defined several assignment sets with different criteria and i always get the same error when i run any quickpaint report.
The same Quickpaint report works well with assignment set defined by including individual assignment.
Thanks in advance!
best regards

Thanks for uploading the sample reports.
I am not abe to reproduce the issue and the graphs generated in both the attached reports are the same except that the width of the graphs being displayed are different as seen in the below images.
ATML 5.1 Report Graph
XML Report Graph
Regards
Srivinayaka Pandurangan
National Instruments
With Best Regards,
Srivinayaka
National Instruments

Adobe Flash 11.1.102.63 not detected with April 2012 PRU

We have recently updated Adobe Flash to version 11.1.102.63 in our ZENworks 10.3.3 zone. I downloaded and applied the April 2012 PRU and it is still not detecting after an inventory. Is there a fix or easy workaround?
Thanks.

Originally Posted by pcwoodring
We have recently updated Adobe Flash to version 11.1.102.63 in our ZENworks 10.3.3 zone. I downloaded and applied the April 2012 PRU and it is still not detecting after an inventory. Is there a fix or easy workaround?
Thanks.
All - it magically worked during the weekly scheduled inventory run. Perhaps some database updates hadn't taken place yet.

785GTM-E45 SATAs Not Detected with RAID Set to AHCI

Similar Messages

Maybe you are looking for