7925G? HELP? Need a real pro for this one?
Our wireless system is completely off our internal network. Its on its own cable broadband connection. The only thing that can touch our lightweight AP's is our wireless server that has 2 NIC cards. One NIC has an ip just to manage the AP's on there seperate c2960 switch and the other NIC has an internal IP so we can remotely manage. How can I hook up these phones so it can reach our internal voice LAN without compromising the network. I have attached a diagram of our wireless setup. I was told i have to use one of the gigabit ports on the switch the AP's connect through and connect it to my ASA box. Please advise. Thank You.
"I have set up my network so that my wireless clients have no access to my internal network. How can I get some of my wireless clients access to my internal network?"
As things stand, you can't.
In order to make this work, you have to make a connection between your TOCWirelessSwitch and your internal LAN.
Now, there are obviously ways to make this as secure as possible- using an ASA and/or ACLs would be the obvious choices- but you will no longer have the complete physical isolation that you do now.
Of course, you would put your wireless phones on a separate SSID and VLAN from your data traffic, and make sure that the only traffic allowed to cross the new connection is restricted to the phone addresses and the specific ports your voice traffic uses.
Similar Messages
-
Help need my mac pro for school..it has Grey screen..spinning wheel...
I think I have mountain lion OS X....I have done I think almost every suggestion I've seen in discussion boards.
Boot in recovery repaired disk...ok...repair disk permission...all repaired but one warning...I've tried to reinstall lion (without losing data) and it Got all the way to one minute to be done and then the time change back two hours and kept doing this all night long. I haven't done a back up due to no external for time machine.
I hope someone can please help me I've been going crazy for a week now trying to figure this out. I use my computer for school and I'm currently very behind from in my school work thank you
Also I've checked my available space 424.91 free of 750 gigs....disk is verifiedWelcome to the Apple Support Communities
Try holding the Shift key while your Mac is starting to start into safe mode. Then, after starting in safe mode, open Finder, select Go menu (on the menu bar) > Go to Folder, and type /Library/StartupItems. Then, empty this folder and restart the Mac.
If your Mac starts after doing this, it was a problem with a third-party app that starts automatically when you turn on the computer. It won't start automatically anymore after doing that -
I have AVI files that I need to convert to MOV files so that I can edit them in Final Cut Pro. I am going to use Quick Time Pro for this....When I have the files open in QT Pro do I have to 'export' it or can I just 'save as', or is there even a difference? Thanks in advance for your help!
I strongly recommend you use compressor to do the conversion (if it will open the files - since quicktime will open them, it will more than likely do it.
Compressor allows you to customize presets and save them and apply them to multiple files. Although the interface may seem daunting, it's actually pretty simple.
Even if you can edit the avi in fcp, it's not a good idea. Liable to cause problems down the road. -
I have an Intel iMac running OSX 10.6.8. I would like to use Final Cut Pro 10.1. I know I need OSX 10.9 for this. Can I run both 10.6.8 and 10.9 on the iMac ? I do not want to convert completely to 10.9 because of my existing software. Thanks for any help
It would depend on how old your IMac is, how mush memory you have, it it can be upgraded by OWC, etc. I have a 2006 Macbook Pro and would NOT put Mavericks on it or espeacially FCP 10.1.1 on it because the most memory it can have is 4 GB. You need at least 8 GB to work with Final Cut Pro 10.1.1. IMHO.
I would try to find a copy of Final Cut Express perhaps.
Does this answer your question? -
I have created a lengthy slideshow with music on my MacBook Pro under Iphoto. What steps do I need to take in order to burn a DVD copy of this slideshow? "Help" does not offer info for this transaction, only if you want to export to another Apple device and it shows that you must first export to Itunes. Can anyone help me with information on just copying to a DVD? I don't want to email it or show it on another Apple device. I want to be able to burn multiple copies on DVDs as a gift...... Can it be done? I'm not real computer savvy
Connect the device to the computer.
In iTunes, select the content desired to sync.
Sync.
This is all described in the User's Guide, reading it may be a good place to start. -
Need help reinstalling Acrobat X pro for MAC. Got one site but I-tunes didn't recognize so couldn't go further. I have serial
Actually, you can and have downloaded from there, because that message only happens when the download is finished.
The message is entirely normal, and is Apple's way of encouraging the world to use the Mac App Store. That doesn't help you because Acrobat isn't in the Mac App Store - it isn't allowed there.
So, what to do? Change your system settings
Please follow the steps given below to resolve this issue -
System Preferences > Security & Privacy > General > Allow applications downloaded from > Anywhere -
i am trying to download some apps onto my iphone 3gs and it keeps saying i need to update it for this but ive trying and there is no update option on the phone or through itunes, it keeps saying its up to date, can anyone help please?
Would this matter then? can you not update the 3g to the lastest software?
-
Hi,
I need a PL/SQL code for this one...
Let me know if something is not clear...
1) The table CLOB_CLOBJECT_CDA has the columns described below...
Explaining only those fields which are important in this context
-- CDA_STEP_ID : Basically a Sequence
-- CLOBJECT_SOURCE1_ID : Every id has got a set of records
-- CLOBJECT_SOURCE2_ID : Every id has got a set of records
-- LVL : There are total 8 levels..
This is the main aim :
1) There are total 16 million rows..(limited to 10 rows here)
2) We need to go through level by level (LVL column) & insert the intersection records (CLOBJECT_SOURCE1_ID intersect CLOBJECT_SOURCE2_ID)
into another table...but this is how it goes..
Level (LVL column) 3's basically have CLOBJECT_SOURCE1_ID as level (LVL column) 2 CDA_STEP_ID's..
(consider the statement --** where CLOBJECT_SOURCE1_ID = 285 which is same as 1st insert statement step id)..
The above process goes for next levels until 8..(so have to use loops)
So for ex :
We go through the first insert statement and insert the insertion records only when both CLOBJECT_SOURCE1_ID & CLOBJECT_SOURCE2_ID has got records ..
If we don't find any records for both of them we should skip the corresponding step id when we go to the next levels...
Let's go through the 1st insert statement...
-- We have CDA_STEP_ID = 285 & two sources CLOBJECT_SOURCE1_ID as 19 & CLOBJECT_SOURCE2_ID as 74...
-- We see the table CLOBJECT_COUNTS & check whether we have counts for both 19 & 74 ..(In fact we insert counts into this table only if they have records)
-- If so, we insert the intersection records into CDA_MRN_RESULTS ( we do have counts for both of them..) with CDA_STEP_ID 285...
-- Then we insert the step id which is 285 along with the count into CLOBJECT_COUNTS..
Let's go through another insert statement...
-- Consider CDA_STEP_ID = 288 which has two sources CLOBJECT_SOURCE1_ID as 19 & CLOBJECT_SOURCE2_ID as 92...
-- We see the table CLOBJECT_COUNTS & check whether we have counts for both 19 & 92 ..(we have records for 19 but not for 92)
-- So we should not proceed with this..& also skip all those records (future records with increasing levels..basically level 3's) which have got 288 as CLOBJECT_SOURCE1_ID..
(As said earlier that the present CDA_STEP_ID will always be CLOBJECT_SOURCE1_ID in the next level)...
I wrote the following code which is after the statement...
Let me have the create & insert statements here..
create table CLOB_CLOBJECT_CDA
CDA_STEP_ID NUMBER,
CDA_ID NUMBER,
CDA_SEQ_NUMBER NUMBER,
CLOBJECT_SOURCE1_TYPE VARCHAR2(3000),
CLOBJECT_SOURCE1_ID NUMBER,
CLOBJECT_OPERATOR VARCHAR2(3000),
CLOBJECT_SOURCE2_TYPE VARCHAR2(3000),
CLOBJECT_SOURCE2_ID NUMBER,
LVL NUMBER
insert into clob_clobject_cda (CDA_STEP_ID, CDA_ID, CDA_SEQ_NUMBER, CLOBJECT_SOURCE1_TYPE, CLOBJECT_SOURCE1_ID, CLOBJECT_OPERATOR, CLOBJECT_SOURCE2_TYPE, CLOBJECT_SOURCE2_ID, LVL)
values (285, 285, 1, 'CLOBJECT', 19, 'INTERSECT', 'CLOBJECT', 74, 2);
insert into clob_clobject_cda (CDA_STEP_ID, CDA_ID, CDA_SEQ_NUMBER, CLOBJECT_SOURCE1_TYPE, CLOBJECT_SOURCE1_ID, CLOBJECT_OPERATOR, CLOBJECT_SOURCE2_TYPE, CLOBJECT_SOURCE2_ID, LVL)
values (286, 286, 1, 'CLOBJECT', 19, 'INTERSECT', 'CLOBJECT', 75, 2);
insert into clob_clobject_cda (CDA_STEP_ID, CDA_ID, CDA_SEQ_NUMBER, CLOBJECT_SOURCE1_TYPE, CLOBJECT_SOURCE1_ID, CLOBJECT_OPERATOR, CLOBJECT_SOURCE2_TYPE, CLOBJECT_SOURCE2_ID, LVL)
values (287, 287, 1, 'CLOBJECT', 19, 'INTERSECT', 'CLOBJECT', 91, 2);
insert into clob_clobject_cda (CDA_STEP_ID, CDA_ID, CDA_SEQ_NUMBER, CLOBJECT_SOURCE1_TYPE, CLOBJECT_SOURCE1_ID, CLOBJECT_OPERATOR, CLOBJECT_SOURCE2_TYPE, CLOBJECT_SOURCE2_ID, LVL)
values (288, 288, 1, 'CLOBJECT', 19, 'INTERSECT', 'CLOBJECT', 92, 2);
insert into clob_clobject_cda (CDA_STEP_ID, CDA_ID, CDA_SEQ_NUMBER, CLOBJECT_SOURCE1_TYPE, CLOBJECT_SOURCE1_ID, CLOBJECT_OPERATOR, CLOBJECT_SOURCE2_TYPE, CLOBJECT_SOURCE2_ID, LVL)
values (4869, 4869, 1, 'CDA_STEP', 285, 'INTERSECT', 'CLOBJECT', 91, 3); -- **
insert into clob_clobject_cda (CDA_STEP_ID, CDA_ID, CDA_SEQ_NUMBER, CLOBJECT_SOURCE1_TYPE, CLOBJECT_SOURCE1_ID, CLOBJECT_OPERATOR, CLOBJECT_SOURCE2_TYPE, CLOBJECT_SOURCE2_ID, LVL)
values (4870, 4870, 1, 'CDA_STEP', 285, 'INTERSECT', 'CLOBJECT', 92, 3);
insert into clob_clobject_cda (CDA_STEP_ID, CDA_ID, CDA_SEQ_NUMBER, CLOBJECT_SOURCE1_TYPE, CLOBJECT_SOURCE1_ID, CLOBJECT_OPERATOR, CLOBJECT_SOURCE2_TYPE, CLOBJECT_SOURCE2_ID, LVL)
values (4871, 4871, 1, 'CDA_STEP', 285, 'INTERSECT', 'CLOBJECT', 93, 3);
insert into clob_clobject_cda (CDA_STEP_ID, CDA_ID, CDA_SEQ_NUMBER, CLOBJECT_SOURCE1_TYPE, CLOBJECT_SOURCE1_ID, CLOBJECT_OPERATOR, CLOBJECT_SOURCE2_TYPE, CLOBJECT_SOURCE2_ID, LVL)
values (4880, 4880, 1, 'CDA_STEP', 286, 'INTERSECT', 'CLOBJECT', 91, 3);
insert into clob_clobject_cda (CDA_STEP_ID, CDA_ID, CDA_SEQ_NUMBER, CLOBJECT_SOURCE1_TYPE, CLOBJECT_SOURCE1_ID, CLOBJECT_OPERATOR, CLOBJECT_SOURCE2_TYPE, CLOBJECT_SOURCE2_ID, LVL)
values (4881, 4881, 1, 'CDA_STEP', 286, 'INTERSECT', 'CLOBJECT', 92, 3);
insert into clob_clobject_cda (CDA_STEP_ID, CDA_ID, CDA_SEQ_NUMBER, CLOBJECT_SOURCE1_TYPE, CLOBJECT_SOURCE1_ID, CLOBJECT_OPERATOR, CLOBJECT_SOURCE2_TYPE, CLOBJECT_SOURCE2_ID, LVL)
values (4882, 4882, 1, 'CDA_STEP', 286, 'INTERSECT', 'CLOBJECT', 93, 3);
create table CDA_MRN_RESULTS
CDA_STEP_ID NUMBER,
MRN NUMBER,
INSERT_DATE_TIME DATE
insert into cda_mrn_results (CDA_STEP_ID, MRN, INSERT_DATE_TIME)
values (19, 1, to_date('19-10-2011', 'dd-mm-yyyy'));
insert into cda_mrn_results (CDA_STEP_ID, MRN, INSERT_DATE_TIME)
values (19, 2, to_date('19-10-2011', 'dd-mm-yyyy'));
insert into cda_mrn_results (CDA_STEP_ID, MRN, INSERT_DATE_TIME)
values (19, 3, to_date('19-10-2011', 'dd-mm-yyyy'));
insert into cda_mrn_results (CDA_STEP_ID, MRN, INSERT_DATE_TIME)
values (74, 1, to_date('19-10-2011', 'dd-mm-yyyy'));
insert into cda_mrn_results (CDA_STEP_ID, MRN, INSERT_DATE_TIME)
values (74, 2, to_date('19-10-2011', 'dd-mm-yyyy'));
insert into cda_mrn_results (CDA_STEP_ID, MRN, INSERT_DATE_TIME)
values (74, 4, to_date('19-10-2011', 'dd-mm-yyyy'));
insert into cda_mrn_results (CDA_STEP_ID, MRN, INSERT_DATE_TIME)
values (75, 1, to_date('19-10-2011', 'dd-mm-yyyy'));
insert into cda_mrn_results (CDA_STEP_ID, MRN, INSERT_DATE_TIME)
values (75, 2, to_date('19-10-2011', 'dd-mm-yyyy'));
insert into cda_mrn_results (CDA_STEP_ID, MRN, INSERT_DATE_TIME)
values (75, 6, to_date('19-10-2011', 'dd-mm-yyyy'));
insert into cda_mrn_results (CDA_STEP_ID, MRN, INSERT_DATE_TIME)
values (91, 2, to_date('19-10-2011', 'dd-mm-yyyy'));
insert into cda_mrn_results (CDA_STEP_ID, MRN, INSERT_DATE_TIME)
values (91, 3, to_date('19-10-2011', 'dd-mm-yyyy'));
create table CLOBJECT_COUNTS
CDA_STEP_ID NUMBER,
CLOBJECT_COUNT NUMBER,
DATE_TIME DATE
Insert into CLOBJECT_COUNTS values (19,3, to_date('19-10-2011', 'dd-mm-yyyy'));
Insert into CLOBJECT_COUNTS values (74,3, to_date('19-10-2011', 'dd-mm-yyyy'));
Insert into CLOBJECT_COUNTS values (75,3, to_date('19-10-2011', 'dd-mm-yyyy'));
Insert into CLOBJECT_COUNTS values (91,2, to_date('19-10-2011', 'dd-mm-yyyy'));The output goes into two tables...
CDA_MRN_RESULTS : O/p of intersection records between source1 & source2 id
CLOBJECT_COUNTS : Step id with counts ...(useful for skipping next level step id's if either of source id has "0" counts)
Any help is appreciated..
Thanks..I tried to code this..but looping takes a lot of time..I want to skip certain rows where source1_step_id & source_2_step_id are not in clobject_counts table as we proceed to the next levels..Not sure how to skip the rows..
declare
cursor c1 (p_level varchar2 ) is
Select * from clob_clobject_cda
where lvl = p_level ;
TYPE V_TT IS TABLE OF C1%ROWTYPE INDEX BY PLS_INTEGER;
L_TT V_TT;
v1 number;
v2 number;
v_step_id number;
v_operator varchar2(100) := '';
begin
for i in 2..8 loop
open c1(i);
LOOP
FETCH C1 BULK COLLECT INTO L_TT LIMIT 500;
FOR indx IN 1 .. L_TT.COUNT
LOOP
v1 := L_TT(indx).clobject_source1_id;
v2 := L_TT(indx).clobject_source2_id;
v_step_id := L_TT(indx).cda_step_id;
v_operator := L_TT(indx).clobject_operator;
Execute Immediate ('Insert into cda_mrn_results Select --+ parallel (cm 128)
distinct ' || v_step_id || ', mrn, trunc(sysdate) dt from cda_mrn_results cm
where cda_step_id = ' || v1 || '
and cda_step_id in (Select cda_step_id from clobject_counts) ' ||
v_operator ||
' Select --+ parallel (cm 128)
distinct ' || v_step_id || ', mrn, trunc(sysdate) dt from cda_mrn_results cm
where cda_step_id = ' || v2 || '
and cda_step_id in (Select cda_step_id from clobject_counts) ' );
Insert --+ Append
into clobject_counts Select cda_step_id, count(distinct mrn),
insert_date_time dt from cda_mrn_results where cda_step_id = v_step_id group by cda_step_id,insert_date_time;
COMMIT;
END LOOP;
EXIT WHEN L_TT.COUNT = 0;
END LOOP;
CLOSE C1;
End Loop;
Commit;
End; -
Need pl/sql stmnts. for this simple logic
Hi,
I need PL/SQL program for this simple logic i am doing mistake somewhere unbale to trace
out ..
select * from GSR03_PO_DTL;
PO_NUM
L53177000 -- > no changes reqd (only one entry with new format)
L00041677 --> to be updated to L41677000(only one entry with OLD format)
L43677000 -- > no change reqd (exists one row with new format and old format like below)
L00043677 -- > to be deleted this is old format (and new format like above already exists)
EX:
L00012345 --- old format
L12345000 --- new format
Hope question is clear. I written the following program.
update is working fine but delete is not working.
Please help.
Thanks in Advance
Devender
declare
Cursor c_test is
(select po_num from GSR03_PO_DTL);
BEGIN
FOR r_test in c_Test
LOOP
dbms_output.put_line (r_test.po_num);
IF ('L'||substr(r_test.po_num,5,5)) = ('L'||substr(r_test.po_num,2,5)) then
dbms_output.put_line ('delete stmnt');
END IF;
EXIT WHEN c_test%NOTFOUND;
END LOOP;
FOR r_test in c_Test
LOOP
IF r_test.po_num like 'L000%' then
IF ('L'||substr(r_test.po_num,5,5)) is not NULL then
update GSR03_PO_DTL set PO_NUM = 'L'||substr(po_num,5,5)||'000'
where po_num like 'L000%' ;
dbms_output.put_line ('update stmnt');
END IF;
END IF;
END LOOP;
END;
*********************No need for PL/SQL, man.
SQL> SELECT po_no FROM po1
2 /
PO_NO
L53177000
L00041677
L43677000
L00043677
SQL> UPDATE po1 y
2 SET y.po_no = 'L'||substr(y.po_no,5,5)||'000'
3 WHERE y.po_no LIKE 'L000%'
4 AND NOT EXISTS ( SELECT null FROM po1 x
5 WHERE x.po_no = 'L'||substr(y.po_no,5,5)||'000')
6 /
1 row updated.
SQL> DELETE FROM po1 y
2 WHERE y.po_no LIKE 'L000%'
3 AND EXISTS ( SELECT null FROM po1 x
4 WHERE x.po_no = 'L'||substr(y.po_no,5,5)||'000')
5 /
1 row deleted.
SQL> SELECT po_no FROM po1
2 /
PO_NO
L53177000
L41677000
L43677000
SQL> Cheers, APC -
A wallet needs to be configured for this instance of Application Express
hi
I m very new to APEX. I could create web service client with wsdl. But when service is on https i get message
"a wallet needs to be configured for this instance of Application Express".
I have created wallet using OWM (10.2.0.1.0) at location c:\del_sometime
Using admin i configured APEX instance settings wallet as
Wallet Path = file:c:\del_sometime
And checked in database too
SQL> ALTER SESSION SET CURRENT_SCHEMA = APEX_030200;
Session altered.
SQL> SELECT
2 APEX_INSTANCE_ADMIN.GET_PARAMETER('WALLET_PATH')
3 from dual;
APEX_INSTANCE_ADMIN.GET_PARAMETER('WALLET_PATH')
file:c:\del_sometime
Any idea whats wrong? I am following steps from http://download.oracle.com/docs/cd/E14373_01/admin.32/e13371/adm_wrkspc.htm#BABFBJEAalso whe I try following i keep getting error failure to open file. I am on XP and file is present with proper permissions.
SQL> SELECT utl_http.request('https://support.oracle.com/',null,'file:c:\del_sometime\') from dual;
SELECT utl_http.request('https://support.oracle.com/',null,'file:c:\del_sometime\') from dual
ERROR at line 1:
ORA-29273: HTTP request failed
ORA-06512: at "SYS.UTL_HTTP", line 1577
ORA-28759: failure to open file
ORA-06512: at line 1 -
Why doesn't my iPhone 4 have an 'Internet tethering' options? Is it carrier related or iOs related? Please help me find the solution for this. thanx
Personal Hot spot
http://support.apple.com/kb/HT3574
Understanding
http://support.apple.com/kb/HT4517
Trouble Shooting
http://support.apple.com/kb/TS2756 -
My nano will not charge. Which is correct port on my macbook pro for this?
my 6 th. generation nano will not charge plugged into my computer. Which should be the correct port on my macbook pro for this?
Any standard USB port should do the job. Have you tried using a different cable?
B-rock -
I am currently getting finder error screen saying "Quartz-filter plugin" error, Please report to apple. Can anyone please help me find a resolution for this error?
If it were me I would schedule an appointment at the store where you bought it and meet with the Manager of the store in person. Print this post and bring it with you along with your iMac.
And change the password on your Apple ID and then see if there are in purchases in your account that you did not make. If there are then someone did get your ID and password. If not someone got your Credit Card information from somewhere and used it. -
I need an Acrobat Pro for several users in our network
I need an Acrobat Pro for several users in our network
If you have enough users a volume license will be a reasonable choice. Again you might contact Adobe or an Adobe reseller.
http://partners.adobe.com/resellerfinder/na/findreseller.jsp -
If i were to get this computer would i need a new network for this or what accessories would i need?
If i were to get this computer would i need a new network for this or what accessories would i need?
If you have WiFI which is not something extremely specific, and I believe it is not - you are fine with network, just go and buy you a computer and enjoy.
Maybe you are looking for
-
File Content Conversion - Error in keyfield Value
Hello experts, I am doing file content conversion for a file to file scenario. The input file is a csv file which is converted to xml using the file content conversion. The key field of input file is used for implementing conversion. While testing th
-
Aperture 3 not recognising RAW files from EOS 300D
When I try to import RAW images from my EOS 300D, I get the message "unsupported image format". I've checked, and Aperture should take RAW from the EOS300D. Could this be firmware levels (I have 1.0.2) or something else?
-
Creating/using folders in iTunes apps section for sync (not iOS folders)
So I use my iPad mainly for work. I have about 600-1000 PDF documents I want to organize. I've been using Goodreader for years. The issue is the initial sync of the Folders, it's too clunky. I have to drag a million files into the Apps section of iTu
-
Just bought a Canon PowerShot SD900 that records XGA quality video as opposed to the standard VGA. The video clips are crystal clear when viewed in iPhoto but not nearly as clear in iMovie. Why would that be? They both open in Quick Time Player. I we
-
Hi all, I've been able to create custom Reports on my IDM instance. However, there's one little thing that keeps irking me : it concerns the "*Send via Email*" function. There's a checkbox there which, when ticked, allows you the option of sending th