7970 firmware load - which file is it ?

I am using callmanager express 4.0 and wish to update the firmware loads on a 7970g phone, I have downloaded the latest updates as shown below :
cnu70.2-7-6-26.sbn
CVM70.2-0-2-26.sbn
Jar70.2-9-2-26.sbn
TERM70.7-0-3-0S.loads
term70.default.loads
After extracting all the files into flash, I configured all the files under tftp-server flash: as shown
tftp-server flash:cnu70.2-7-6-26.sbn
tftp-server flash:CVM70.2-0-2-26.sbn
tftp-server flash:Jar70.2-9-2-26.sbn
tftp-server flash:TERM70.7-0-3-0S.loads
tftp-server flash:term70.default.loads
But I am unsure as to which file to load under telephony-service for "load 7970 filename" ???
Checking ciscos link for more information about updating the 7970 at
http://www.cisco.com/en/US/products/hw/phones/ps379/products_administration_guide_chapter09186a00801d66ba.html
It says : "Read the "Read Me" files included with Cisco software updates. These files provide important updated information about installing and configuring the new software." but there is no readme file with the firmware update ?
A bit confusing any help would be appreciated ?
Thanks

Hi Mark,
Perhaps this will help, I am pretty sure that you would use;
load 7970 TERM70.7-0-3-0S
Upgrading Individual Phone Firmware Files
From this good CME doc;
http://www.cisco.com/en/US/products/sw/voicesw/ps4625/products_configuration_guide_chapter09186a00806a8022.html#wp1003359
Hope this helps!
Rob
Please remember to rate helpful posts.....

Similar Messages

What is the difference between Device pack & Firmware load

We have purchased a new Phone with model: 7821. We have the CUCM version 8.6.2. As the phone model is not listed int the "Phone type" to Add the phones. I've verified and found the Device pack "cmterm-devicepack8.6.2.26149-1.cop.sgn" and Firmware load "
cmterm-78xx.10-2-1-12SR1-4.cop.sgn".
Could you please provide difference between them? Is it installing Firmware load suffice for adding the new phone mode: 7821?

Devices packs are a collection of the latest device firmwares available for CUCM. They will also add support for new devices.
Firmware loads are just updated firmware for a particular device.
Occasionally Cisco release a QED file which adds support for just one particular device to CUCM without the need for a device pack.
GTG

Loading flat files located on a server using the Control Center piece ofOWB

Loading flat files from a server with OWB
I am successful loading files with OWB, as long as they resided on my workstation in the C:\ drive. I copied the files to a Linux server into directories owned by Oracle/oinstall, permissions on the directories containing the files are 777. I ran the OWB client from the server with the following results:
Error
RPE-01013: SQL Loader reported error condition, number 1.
SQL*Loader: Release 10.2.0.1.0 - Production on Fri Mar 9 11:15:58 2007
Copyright (c) 1982, 2005, Oracle. All rights reserved.
SQL*Loader-500: Unable to open file (/u00/data/owb_repos1/state_codes.csv)
SQL*Loader-553: file not found
SQL*Loader-509: System error: The system cannot find the file specified.
SQL*Loader: Release 10.2.0.1.0 - Production on Fri Mar 9 11:15:58 2007
Copyright (c) 1982, 2005, Oracle. All rights reserved.
SQL*Loader-500: Unable to open file (/u00/data/owb_repos1/state_codes.csv)
SQL*Loader-553: file not found
SQL*Loader-509: System error: The system cannot find the file specified.
I tried to load the file using the control center from both the windows client and the server client. Can I do this from either one?
I can't import the file in the Design Center from the /u00/data/owb_repos1 directory, it does not show up.
If anyone has received similiar errors from OWB, please tell me how I can fix this. THANKS!!!
[d97886@owbtest owb_repos1]$ pwd
/u00/data/owb_repos1
[d97886@owbtest owb_repos1]$ ls -la
total 24
drwxrwxrwx 2 oracle oinstall 4096 Mar 19 12:14 .
drwxrwxrwx 18 oracle oinstall 4096 Mar 6 16:41 ..
-rwxrwxrwx 1 oracle garrett 1481 Mar 8 07:32 state_codes.csv
[d97886@owbtest owb_repos1]$

Hi
This is what i do for my flat files (i am loading my tables from the flat files):
1) Create location for the files in OWB and it should look something like \\path_to_where_the_files_are. Here you should be able to browse to your Linux box and select the location of the files.
2) Then check whatever you use (i use TOAD) and you should see in owb schema a directory created there which points to the location of the flat file.
3) then just follow the guide to sample the files etc and you are good to go.
Basically OWB has to be able to see the files that are on Linux machine.
Alternatively you can map your Linux share to your windows box (use samba or something) and use it that way.
Sorry if it is stating the obvious.
Hope this helps
Kind Regards
Vix

Error Loading the file from application server

Hi Team,
I'm trying to load the .CSV file from application server and I'm getting the error message.
In the data package
Update to PSA --Green
Transfer Rule -- Green
Update Rule - error ABORT was set in the customer routine 9998
Error 1 in the update
Please help me to provide the solution.
But when I try to load the other files there are no issues. thanks.
Regards,
Senthil

Raj
check the below links, which can helps to solve your issues
Flat file data load
flat file Data loading issue
Mahesh

Photoshop crashes when loading a file or image

Using Photoshop cs3 on a PC with Windows 7 installed.
Major Problem: Photoshop gives no response when opening an image of any sort or psd file which ends out with the options to either close the program or close and find a solution online which gives no solution whatsoever.
PScs3 was working just fine when installed but after installing an NVIDIA plug-in did it start bearing some problems. When loading png files, a window normally appears telling me that Photoshop could not parse the file. After seeing this I went to uninstall the plug-in. The problem seemed to went away but shortly after was Photoshop crashing at random, and I do mean random. Starting Photoshop at first seems to nullify the chances of crashing but after either a short period of time or a long period of time will it crash when trying to open a file. Opening multiple files at once doesn't work either but when opening only one file into PScs3 will it cooperate until opening a second. I'm not sure if the plug-in is what caused the problem but I do know everything from there seems hectic. Every crash leads me opening PScs3 again with all of its settings reset from when I first exited normally.
Plugin Used:
Photoshop_Plugins_8.23.1101.1715
Appications Type; 4,317 KB
Company - InstallShield Softwere Corporation
Have you tried uninstalling and reinstalling the program?
Unfortunetly yes I have attempted this and the problem still occurs towards cs3. This makes me fear that the entire program is glitched.
Do you have any other plug-ins installed?
I've checked and there are no other plug-ins attatched.
This is my last option before seeing to reformat my computer. If there is any input about the topic, now is the time.

Just a hunch: change your default printer to something else (a locally attached printer, not networked) or "PrintToPDF", then relaunch Photoshop and try again.
It could also be a plugin (try disabling ALL third party plugins).
And it could be a bad OS install, a virus, etc. It may take a while to find.

How to load a file with out specifying its absolute location

Hi,
I'm having some config files in a specific location. I'm setting that folder path to the CLASSPATH and trying access those file just by giving its name.
For eg: contents are in e:\config folder
I set e:\config to CLASSPATH
and trying to load the file which is in the above said folder.
using getResourceAsStream(filename).
The above approach is working in certain cases, but not working when i try to do in a class which under a big package structure.
Can someone help me out, the reason for this unexpected behaviour.
Please do suggest me, if u know some work-around for this problem.
Thnaks in advance,
Chandrasekhar

Hi,
Thank you. I tried by adding a forward slash, it started working.
But I still have one doubt, when the program is within the package structure, then we have to give forward slash, where as if the program doesn't have any pkg structure we have to give only the file name without prefixing the slash.
Any idea, why is it so ??
Is it bcz, that getOutputAsStream() will prepend the package names, if forward slash is not given. Even if this is true, why providing a forward slash in a program with no packages doesn't work ?

How to load flat file in existing Architecture.

Hi everyone!
There is an existing architecture that I have to upload data into. There is a cube on top, followed below by an ODS and its update rules to the cube, followed below by an Infosource and its corresponding update rule to the ODS above it, followed below by a datasource (it says PC FILES(PC_FILE)) and its accompanying transfer rules to the infosource....
There is nothing in the ODS... No data. The Datasource says emmulated 3.x Datasource... (What does this mean?)
What I want to do is upload data via a flat file... Good BI Masters, how do I do this? How do I create a "dummy file" for upload? What are the specific sequence of steps that I need to do to load this flat file data?
Thank thank you so much!
Philips

emulated DS:
http://help.sap.com/saphelp_nw04s/helpdata/en/8c/131e3b9f10b904e10000000a114084/frameset.htm
I'm not sure what you are asking - is it how to load a file all the way to cube in 7.0?
From the architecture desc you have given, you havent migrated ur dataflow to new 7.0 dataflow, as you still have the update rules and transfer rules. So though ur system is 7.0, ur backend is still on 3.x, so the way you load a file is the same when your system was 3.x(before upgrade)
Or - are you asking the steps to load the file to a cube - no matter which environment you are in (3.x or 7.0)? if so, let us know .. and do a search on the forum for steps to load flatfile

4.2.3/.4 Data load wizard - slow when loading large files

Hi,
I am using the data load wizard to load csv files into an existing table. It works fine with small files up to a few thousand rows. When loading 20k rows or more the loading process becomes very slow. The table has a single numeric column for primary key.
The primary key is declared at "shared components" -> logic -> "data load tables" and is recognized as "pk(number)" with "case sensitve" set to "No".
While loading data, these configuration leads to the execution of the following query for each row:
select 1 from "KLAUS"."PD_IF_CSV_ROW" where upper("PK") = upper(:uk_1)
which can be found in the v$sql view while loading.
It makes the loading process slow, because of the upper function no index can be used.
It seems that the setting of "case sensitive" is not evaluated.
Dropping the numeric index for the primary key and using a function based index does not help.
Explain plan shows an implicit "to_char" conversion:
UPPER(TO_CHAR(PK)=UPPER(:UK_1)
This is missing in the query but maybe it is necessary for the function based index to work.
Please provide a solution or workaround for the data load wizard to work with large files in an acceptable amount of time.
Best regards
Klaus

Nevertheless, a bulk loading process is what I really like to have as part of the wizard.
If all of the CSV files are identical:
use the Excel2Collection plugin ( - Process Type Plugin - EXCEL2COLLECTIONS )
create a VIEW on the collection (makes it easier elsewhere)
create a procedure (in a Package) to bulk process it.
The most important thing is to have, somewhere in the Package (ie your code that is not part of APEX), information that clearly states which columns in the Collection map to which columns in the table, view, and the variables (APEX_APPLICATION.g_fxx()) used for Tabular Forms.
MK

How to dynamically load jar files - limiting scope to that thread

Dynamically loading jar files has been discussed a lot. I have read a quite a few posts, articles, and demo code for doing just that. However, I have yet to find a solution to my problem. Most people modify their system class loader and are happy. I have done that and was happy for a time. Occasionally, you will see reference to an application server or tomcat or some other large project that have successfully been able to load and unload jar files, allow for dynamic deployment of code, etc. However, I have not been able to achieve similar success; And my problem is much less complicated.
I have an application that executes a thread to send a given file/message to a standard JMS Server Queue. Depending on the parameters selected by the user, this thread may need to communicate with one of a number of JMS Servers, ie. JBoss, WebLogic, EAServer, Glassfish, etc. All of which can be done with the same code, but each needs to load their own flavor of JMS Client Jar files. In this instance, spawning a separate JVM for each communication would work from a classloader perspective. However, I need to keep it in the family and run under the same JVM, albeit each JMS Server Connection will be created and maintained in separate Threads.
I am close, I am doing the following...
1. Creating a new URLClassLoader in the run() method of each thread.
2. Set this threads contextClassLoader to the new URLClassLoader.
3. Load the javax.jms.JMSException class with the URLClassLoader.loadClass() method.
4. Create an initialContext object within this thread.
Note: I read that the initialContext and subsequent conext lookup calls would use the Thread�s
contextClassLoader for finding/loading classes.
5. Perform context.lookup calls for a connectionFactory and Queue name.
6. Create JMS Connection, etc. Send Message.
Most of this seems to work. However, I am still getting a NoClassDefFoundError exception for the javax.jms.JMSException class ( Note step #3 - tried to cure unsuccessfully).
If I include one of the JMS Client jar files ( ie wljmsclient.jar for weblogic ) in the classpath then it works for all the different JMS Servers, but I do not have confidence that each of the providers implemented these classes that now resolve the same way. It may work for now, but, I believe I am just lucky.
Can anyone shine some light on this for me and all the others who have wanted to dynamically load classes/jar files on a per Thread basis?

Thanks to everyone - I got it working!
First, BenSchulz' s dumpClassLoader() method helped me to visualize the classLoader hierarchy. I am still not completely sure I understand why my initial class was always found by the systemClassLoader, but knowning that - was the step I needed to find the solution.
Second, kdgregory suggested that I use a "glue class". I thought that I already was using a "glue class" because I did not have any JMSClient specific classes exposed to the rest of the application. They were all handled by my QueueAdmin class. However...
The real problem turned out to be that my two isolating classes (the parent "MessageSender", and the child "QueueAdmin") were contained within the same jar file that was included in the classpath. This meant that no matter what I did the classes were loaded by the systemClassLoader. Isolating them in classes was just the first step. I had to remove them from my jar file and create another jar file just for those JMSClient specific classes. Then this jar file was only included int custom classLoader that I created when I wanted to instantiate a JMSClient session.
I had to create an interface in the primary jar file that could be loaded by the systemClassLoader to provide the stubs for the individual methods that I needed to call in the MessageSender/QueueAdmin Classes. These JMSClient specific classes had to implement the interface so as to provide a relationship between the systemClassLoader classes and the custom classLoader classes.
Finally, when I loaded and instantiated the JMSClient specific classes with the custom classLoader I had to cast them to the interface class in order to make the method calls necessary to send the messages to the individual JMS Servers.
psuedu code/concept ....
Primary Jar File   - Included in ClassPath
Class<?> cls = ClassLoader.loadClass( "JMSClient.MessageSender" )
JMSClientInterface jmsClient = (JMSClientInterface) cls.newInstance()
jmsClient.sendMessage()
JMSClient Jar File - Loaded by Custom ClassLoader Only
MessageSender impliments Primary.JMSClientInterface{
    sendMessage() {
        Class<?> cls=ClassLoader.loadClass( "JMSClient.QueueAdmin" )
        QueueAdmin queueAdmin=(QueueAdmin) cls.newInstance()
        queueAdmin.JMSClientSpecificMethod()
    }

I'm trying to load video file into CS6 I keep getting error message: 'Could not complete you request because the DynamicLink Media Server is not available.' No Idea what to do next. Help please.

I'm using CS6 Extended. My OS is "Windows 7 home premium.
Can no longer load video files into CS6 for edited I keep getting error message:
'Could not complete your request because the DynamicLink Media Server is not available.'
Don't know what this means. Until just now I was able to load videos without any problems. Now I'm getting this message. Any thoughts?

Hi Mylenium,
upfront:
I hope I won't be marked as spam now, since I am posting on a few relevant discussions now to this topic.
However, I really would like to ask the people who have experienced this problem to see if they were able to solve it.
Now the real deal:
I posted a question in this discussionDynamicLink Media Server won't let me import video for video frames to layers anymore.
The linked discussion is a lot younger, which is why I posted there first.
I also put in information on the steps that I have tried and my computer specifications.
I am experiencing this problem for a while now and hope you and jones1351may be able to help out.

Load XML file from addon domain without cross-domain Policy file

Hello.
Assuming that there are two addon domains on the same server: /public_html/domain1.com      and      /public_html/domain2.com
I try to load XML file from domain2.com into domain1.com without using cross-domain policy file (since it doesn’t work on xml files in my case).
So the idea is to use php file in order to load XML and read it back to flash.
I’ve found an interesting scripts that seems to do the job but unfortunately I can't get it to work. In my opinion there is somewhere problem with AS3 part. Please take a look.
Here are the AS3/PHP scripts:
AS3 (.swf in www.domain1.com):
// location of the xml that you would like to load, full http address
var xmlLoc:String = "http://www.domain2.com/MyFile.xml";
// location of the php xml grabber file, in relation to the .swf
var phpLoc:String = "loadXML.php";
var xml:XML;
var loader:URLLoader = new URLLoader();
var request:URLRequest = new URLRequest(phpLoc+"?location="+escape(xmlLoc) );
loader.addEventListener(Event.COMPLETE, onXMLLoaded);
loader.addEventListener(IOErrorEvent.IO_ERROR, onIOErrorHandler);
loader.load(request);
function onIOErrorHandler(e:IOErrorEvent):void {
    trace("There was an error with the xml file "+e);
function onXMLLoaded(e:Event):void {
    trace("the rss feed has been loaded");
    xml = new XML(loader.data);
    // set to string, since it is passed back from php as an object
    xml = XML(xml.toString());
    xml_txt.text = xml;
PHP (loadXML.php in www.domain1.com):
<?php
header("Content-type: text/xml");
$location = "";
if(isset($_GET["location"])) {
    $location = $_GET["location"];
    $location = urldecode($location);
$xml_string = getData($location);
// pass the url encoded vars back to Flash
echo $xml_string;
//cURLs a URL and returns it
function getData($query) {
    // create curl resource
    $ch = curl_init();
    // cURL url
    curl_setopt($ch, CURLOPT_URL, $query);
    //Set some necessary params for using CURL
    curl_setopt($ch, CURLOPT_SSL_VERIFYPEER, false);
    curl_setopt($ch, CURLOPT_RETURNTRANSFER, 1);
   //Execute the curl function, and decode the returned JSON data
    $result = curl_exec($ch);
    return $result;
    // close curl resource to free up system resources
    curl_close($ch);
?>

I think you might be right about permissions/settings on the server for php. Unfortunately I'm not allowed to adjust them.
So I wrote my own script - this time I used file path instead of http address of the XML file. It works fine in my case.
Here it is:
XML file on domain2.com:
<?xml version="1.0" encoding="UTF-8"?>
<gallery>
    <image imagePath="galleries/gallery_1/images/1.jpg" thumbPath="galleries/gallery_1/thumbs/1.jpg" file_name= "1"> </image>
    <image imagePath="galleries/gallery_1/images/2.jpg" thumbPath="galleries/gallery_1/thumbs/2.jpg" file_name= "2"> </image>
    <image imagePath="galleries/gallery_1/images/3.jpg" thumbPath="galleries/gallery_1/thumbs/3.jpg" file_name= "3"> </image>
</gallery>
swf on domain1.com:
var imagesXML:XML;
var variables:URLVariables = new URLVariables();
var varURL:URLRequest = new URLRequest("MyPHPfile.php");
varURL.method = URLRequestMethod.POST;
varURL.data = variables;
var MyLoader:URLLoader = new URLLoader;
MyLoader.dataFormat =URLLoaderDataFormat.VARIABLES;
MyLoader.addEventListener(Event.COMPLETE, XMLDone);
MyLoader.load(varURL);
function XMLDone(event:Event):void {
    var imported_XML:Object = event.target.data.imported_XML;
    imagesXML = new XML(imported_XML);
   MyTextfield_1.text = imagesXML;
   MyTextfield_2.text = imagesXML.image[0].attribute("thumbPath"); // sample reference to attribute "thumbPath" of the first element
php file on domain1.com:
<?php
$xml_file = simplexml_load_file('../../domain2.com/galleries/gallery_1/MyXMLfile.xml'); // directory to XML file on the same server
$imported_XML = $xml_file->asXML();
print "imported_XML=" . $imported_XML;
?>
Regards
PS: for those who read the above discussion: the first and the second script work but you must test which one is better in your situation. The first script will also work between two domains on different servers. No cross domain policy file needed.

Can I load xml file from SWC without using @embed

I'm developing a mobile application in which I need to load xml files from File.applicationDirectory. This works great if the xml files are part of the main application swf. But I would like to move these xml files into a SWC so they could be shared across multiple applications.
Using FlashBuilder 4.5, when a SWC is built, I can specify files to embed in the library that are not assets (Assets Tab of Flex Library Build Path). For various design reasons, I do NOT want to embed the xml files via @embed.
When the swc is built and I open it up using a zip utility, I see the xml files in there just fine. So they are being bundled with the SWC. But how can I load these files in my main application that does not involve using @embed? When the main application is built, the swc setting for link type is "merged into code".
I wouldn't expect the application to automatically pull out the xml files from the swc and place them in the File.applicationDirectory on the mobile device. I've tried loading from there just in case but file.exists is false (as expected).
I've searched the web (and continue to do so) and all the answers seem to be to use @embed. Is there another way?
Randy

It's actually a lot easier than you think.
Just reference the file like any'ol URL using a path relative to the SWC's src directory.
So if you include the file "assets/xml/some.xml", just use that same string like you would any remote resource.
For example:
var loader:URLLoader = new URLLoader( new URLRequest("assets/xml/some.xml"));
I believe it would also work like this "/assets/xml/some.xml", but I prefer relative paths so the link doesnt break if moved out of the SWC...

Issue in How-To document "Load flat file using SAPGUI"?

Hi,
I'm having an issue with following lines in the How-To document.
I've a characteristic "CHAR1" which is restricted with multuple values in the planning level.
after the upload using this document, CHAR1 is being loaded incorrect & during my debugging I've noticed that program is changing CHAR1 values while executing following lines of code.
It works fine, if i don't have a restriction for CHAR1 at planning level.
It also works fine, if i restricted CHAR1 with a single value in level.
It's not working as expected, if i restrict CHAR1 with multiple single values.
incase of multiple single values restriction, following is happening.
let's say i load following file & i restricted CHAR1 with values "aaaaa,fffff" in level.
CHAR1 CHAR2 value
aaaaa bbbbb 1000
fffff eeeee 2000
it's being loaded as follows. Program is changing all values of CHAR1 with 1st value of the restricted multiple values and in this case, it is "aaaaa".
CHAR1 CHAR2 value
aaaaa bbbbb 1000
aaaaa eeeee 2000
Has any one encountered the same problem?
Marc,
Could you please comment on this.
>>> INSERT
Set fixed fields
LOOP AT ito_chasel INTO ls_chasel.
READ TABLE ls_chasel-t_charng INTO ls_charng INDEX 1.
IF sy-subrc = 0 AND ls_charng-option = 'EQ'.
ASSIGN COMPONENT ls_chasel-chanm OF STRUCTURE ls_data-s_chas TO <f>.
IF sy-subrc = 0.
<f> = ls_charng-low.
ENDIF.
ENDIF.
ENDLOOP.
<<< INSERT
Appreciate any help.
Hari Immadi
http://immadi.com
SEM BW Analyst

Marc,
I still need to keep the lines of coding as I've few characteristics restrictied to single values & one characteristic restricted to multiple single values.
when the coding is commented out, single value restricted characteristics are not getting populated with any value.
I'm counting the table entries "ls_chasel-t_charng" and if entries are 1, then am activating the code. this seems to be working fine. Do you see any problems/issues with this?
Hari Immadi
http://immadi.com
SEM BW Analyst

Issue in calling webdynpro for loading flat file in IP

Hello,
We have implemented the How-To load flat files in IP paper and we are facing an issue in that. The generated webdynpro runs on ABAP Application server but we need to call this from a Web template which runs on portal server.
These two servers are different and we don't want to hardcode the url in webtemplate as the server names will change in Q & P for webdynpro. Can anyone advise how we can read the ABAP Application server details in WAD may be using javascript and then generate the URL for webdynpro dynamically.
Regards,
Deepti

Hi Deepti,
We have also facing the same challenge. Could you please post the solution in which URL path change dynamically.
I have created the ABAP function module based on the below link.
http://wiki.sdn.sap.com/wiki/display/Snippets/BICustomWebItemtoLaunchanABAPWeb+Dynpro
But not sure how to call the function module using custom web item & java script. Coould you please explain the steps on the same ?
Thanks,
Gopi R

Create sql loader data file dynamically

Hi,
I want a sample program/approach which is used to create a sql loader data file.
The program will read table name as i/p and will use
select stmt will column list derived from user_tab_columns from data dictionary
assuming multiple clob columns in the column list.
Thanks
Manoj

I 'm writing clob and other columns to a sql loader dat file.
Below sample code for writing clob column is giving file write error.
How can I write multiple clobs to dat file so that control file will handle it correctly
offset NUMBER := 1;
chunk VARCHAR2(32000);
chunk_size NUMBER := 32000;
WHILE( offset < dbms_lob.getlength(l_rec_type.narrative) )
LOOP
chunk := dbms_lob.substr(l_rec_type.narrative, chunk_size, offset );
utl_file.put( l_file_handle, chunk );
utl_file.fflush(l_file_handle);
offset := offset + chunk_size;
END LOOP;
utl_file.new_line(l_file_handle);

7970 firmware load - which file is it ?

Similar Messages

Maybe you are looking for