7k vPC best practice with multiple line cards?

I have a pair of 7k's that have a single line card with a 2 port vPC linked to a pair of 5k's, another 2 port vPC linked to the layer 3 VDC and a 4 port vPC used for peer link. I recently added an additional line card to the 7k’s and want to add redundancy for the new line card.  Would it be best to simply remove one of the existing ports from each vPC on line card 1 and then include a port from the new line card? For the peer link, my thought was to remove two ports from the existing port channel and then add back 2 ports from the new line card. This way line card 1 and 2 will share the ports that make up the vPC’s instead of all of the vPC ports being on line card 1. Does that make sense or is there a better way to implement line card redundancy after adding a new line card?
Also, if I want to add some of the ports on line card 2 to the layer 3 VDC. Can I run the allocate interface command without the fear of it removing any existing allocated ports?  I understand that the ports being moved/allocated to a different VDC will lose their current configuration.  I had a bad experience years ago using "switchport trunk vlan allowed" vs. "switchport trunk vlan allowed add" command so I just want to make sure the allocate interface doesn't require the "add" option! :)
Thanks!

Hi,
For adding new interface to port-channel:
1. you can shutdown the new physical interface and put all the configure as existing member interface.
2. add as port-channal member.
3. Unshut the physical interfaces (new interface- module 2).
4. Shutdown the physical interfaces (module 1) which you wanted to remove from the port-channel
Moving interface from one VDC another VDC will erase the configuration on that interface . you could use allocate interface command to add new interface to the VDC but all the interface should be in same port group. Adding new interface to vdc will not affect existing interface configuration .
HTH
Regards,
VS.Suresh.
*Plz rate the usefull posts *

Similar Messages

Error Message with multiple line

Hi
How to display a error message with multiple line?
Example
     Goods movement not possible for material 101
     Goods movement not possible for material 102
     Goods movement not possible for material 103
is it possible is ABAP? If so please advice me.
Best Regards
Asheek

Hi Anoop,
You can use same thing like this
I suggest write ur message through this.
First set the obecj.
CALL FUNCTION 'APPL_LOG_SET_OBJECT'
for local memory
FUNCTION 'APPL_LOG_WRITE_MESSAGES'
         EXPORTING
              OBJECT              = OBJECT
              SUBOBJECT           = SUBOBJECT
              UPDATE_OR_INSERT    = UPDATE_INSERT_FLAG
         TABLES
              MESSAGES            = MESSAGE_TABLE
         EXCEPTIONS
              OBJECT_NOT_FOUND    = 1
              SUBOBJECT_NOT_FOUND = 2
              OTHERS              = 3.
the call for physical memory
CALL FUNCTION 'APPL_LOG_WRITE_DB'
In this process you only need to provide the Itab with error messages.
Reg,
Arpit

Word property with multiple lines

Good Morning,
I have a Document Library with an Word template, I fill some properties of the library so I can put this properties in the template. I am trying to write a line break, Any idea?
Thanks.

Hi,
According to your post, my understanding is that you want to use Word property with multiple lines.
Per my knowledge, you can remove two updates: KB2760769 and
KB2760758.
The working version of office is 14.0.6129.5000.
Here is a similar thread for your reference:
http://sharepoint.stackexchange.com/questions/77759/inserting-multi-line-text-field-quick-part-from-sharepoint-crashes-word
More information:
Office 2010 Update KB2760758 Incorrectly Checks Multi-Line Columns
As this question is more relate to Word, I suggest you post it to the corresponding forum, you will get more help and confirmed answers from there.
http://social.technet.microsoft.com/Forums/en-US/home?forum=officesetupdeployprevious
Best Regards,
Linda Li
Linda Li
TechNet Community Support

Best Practice for Multiple iTunes and One Account?

My wife and I share our account for our iPhone Applications and Songs in iTunes.
Can someone point me to a topic that covers a best practice for multiple iTunes syncing?
I travel a lot and keep my iPhone synced to my Macbook Pro while she uses the workstation at home to sync to. We keep the addresses and contacts and calendars synced through MobileMe, however, I'm trying to find the best way of pushing applications and songs I've bought over to the other PC so they're still around while I'm traveling for her to sync with.
Thoughts?

Hi Steve,
Might be trying for solution for a long time, If i understood your question clear let me clarify you few points.
You are trying to access the bex query which is designed with the exit's in the background based on the logic and trying to call the entire dimensions and key-figures in a single connection. Then you are trying to map those data in the charts.
Steve, try to make more connections based upon the logic and split them. use the same query but split them by sales per customer group, sales per day, sales per week by making three different connections and try. You can merge the prompts from all connections.
Hope this Helps!!!
Sorry if i misunderstood your question.
--SumanT

Create ecatt script for one sales order creation with multiple line items

Hi ,
I want to create a ecatt script for one sales order creation with multiple line items. Preferably SAP GUI.
This selection of data will be from an external file/ variants which will have only one row of data in it.
Firstly: I have to sort the external file having same PO Numbers in an order.Group them together.
Second: I have to create sales order for those many line items having same PO Number.
Best Regard
Taranum

Hi Micky
Firstl you should upload the Line items for a particular sales Order in an Internal table
and then pass that internal table to your BAPI during your coding corresponding to a particu;lar sales order
In case of any issues pls revert back
Reward points if helpful
Regards
Hitesh

String Array declaration with multiple lines

I have an array declaration with several indexes where it covers multiple lines.
Please advise if this is the best way to declare an array declaration with multiple lines:
String cityString = "San Diego, Oakland, London, New York, Dublin," +
"Dallas, Milan";
String city[] = cityString.split(",");

String[] city = {"San Diego", "Oakland", "London",
"New York", "Dublin", "Dallas", "Toronto"};You can use indentation and line breaks as you like, as usual in Java.

Printing Text with multiple Lines

Hello,
i want to print a list and in that is text with multiple lines.
In the PrintPreview and in the Printout i get only one line.
How is the best way to do this?
Thank you,
Markus
Private Function Print_Remarks_Control_Get(ByVal pstrText As String) As TextBox
Dim TextBox_Out As New TextBox
With TextBox_Out
.Text = pstrText
.HorizontalAlignment = Xaml.HorizontalAlignment.Left
.VerticalAlignment = Xaml.VerticalAlignment.Top
.FontSize = 16
.Margin = New Thickness(15)
.AcceptsReturn = True
.MinWidth = 800
.MinHeight = 600
End With
Return TextBox_Out
End Function
Sub PrintPageList_Prepare()
Dim i As Integer
Dim objVM As clsTextVM
Dim lstText_List As ObservableCollection(Of clsText)
Dim ctrPrint_StackPanel As StackPanel
Dim ctrPrint_Title As TextBox
Dim ctrPrint_Description As TextBox
Dim ctrPrint_Remarks As TextBox
Dim objText As clsText
mPrintPageList.Clear()
objVM = DirectCast(Me.DataContext, clsTextVM)
lstText_List = objVM.CustomClass_List
ctrPrint_StackPanel = Print_StackPanel_Get()
For i = 0 To lstText_List.Count - 1
objText = lstText_List.Item(i)
If objText.Name.Length > 0 Then
ctrPrint_Title = Print_Title_Control_Get(objText.Name)
ctrPrint_StackPanel.Children.Add(ctrPrint_Title)
End If
If objText.Description.Length > 0 Then
ctrPrint_Description = Print_Description_Control_Get(objText.Description)
ctrPrint_StackPanel.Children.Add(ctrPrint_Description)
End If
If objText.Remarks.Length > 0 Then
ctrPrint_Remarks = Print_Description_Control_Get(objText.Remarks)
ctrPrint_StackPanel.Children.Add(ctrPrint_Remarks)
End If
Next
mPrintPageList.Add(ctrPrint_StackPanel)
End Sub
Private Sub OnGetPreviewPage(sender As Object, e As GetPreviewPageEventArgs)
' Das ist die MessageBox
' Windows.UI.Popups.MessageDialog()
PrintPageList_Prepare()
mPrintDok.SetPreviewPage(e.PageNumber, Me.mPrintPageList(e.PageNumber - 1))
End Sub

Yes, not only RichEditBox but also RichTextBlock can also do this. Besides TextBox also have TextWrapping functionality.
-James
We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
Click
HERE to participate the survey.

Patch names with multiple lines

I am using patch names with multiple lines, e. g.:
Intro: In my car
Piano / Brass
Theese patch names appear correctly in the patch list in edit mode, but completely disrupted in perform mode (the two lines are displayed vertically centered, son one can see the lower half of the upper line, and the upper half of the lower l

I wrote my question here because I didn't find a MainStage forum?! Do you have a link?
Best, Dietmar

IPS Tech Tips: IPS Best Practices with Cisco Remote Management Services

Hi Folks -
Another IPS Tech Tip coming up and this time we will be hearing from some past and current Cisco Remote Services members on their best practice suggestions. As always these are about 30 minutes of content and then Q&A - a low cost high reward event.
Hope to see you there.
-Robert
Cisco invites you to attend a 30-45 minute Web seminar on IPS Best   Practices delivered via WebEx. This event requires registration.
Topic: Cisco IPS Tech Tips - IPS Best Practices with Cisco Remote Management   Services
Host: Robert Albach
Date and Time:
Wednesday, October 10, 2012 10:00 am, Central Daylight Time (Chicago,   GMT-05:00)
To register for the online event
1. Go to https://cisco.webex.com/ciscosales/onstage/g.php?d=203590900&t=a&EA=ralbach%40cisco.com&ET=28f4bc362d7a05aac60acf105143e2bb&ETR=fdb3148ab8c8762602ea8ded5f2e6300&RT=MiM3&p
2. Click "Register".
3. On the registration form, enter your information and then click   "Submit".
Once the host approves your registration, you will receive a confirmation   email message with instructions on how to join the event.
For assistance
http://www.webex.com
IMPORTANT NOTICE: This WebEx service includes a feature that allows audio and   any documents and other materials exchanged or viewed during the session to   be recorded. By joining this session, you automatically consent to such   recordings. If you do not consent to the recording, discuss your concerns   with the meeting host prior to the start of the recording or do not join the   session. Please note that any such recordings may be subject to discovery in   the event of litigation. If you wish to be excluded from these invitations   then please let me know!

Hi Marvin, thanks for the quick reply.
It appears that we don't have Anyconnect Essentials.
Licensed features for this platform:
Maximum Physical Interfaces       : Unlimited      perpetual
Maximum VLANs                     : 100            perpetual
Inside Hosts                      : Unlimited      perpetual
Failover                          : Active/Active perpetual
VPN-DES                           : Enabled        perpetual
VPN-3DES-AES                      : Enabled        perpetual
Security Contexts                 : 2              perpetual
GTP/GPRS                          : Disabled       perpetual
AnyConnect Premium Peers          : 2              perpetual
AnyConnect Essentials             : Disabled       perpetual
Other VPN Peers                   : 250            perpetual
Total VPN Peers                   : 250            perpetual
Shared License                    : Disabled       perpetual
AnyConnect for Mobile             : Disabled       perpetual
AnyConnect for Cisco VPN Phone    : Disabled       perpetual
Advanced Endpoint Assessment      : Disabled       perpetual
UC Phone Proxy Sessions           : 2              perpetual
Total UC Proxy Sessions           : 2              perpetual
Botnet Traffic Filter             : Disabled       perpetual
Intercompany Media Engine         : Disabled       perpetual
This platform has an ASA 5510 Security Plus license.
So then what does this mean for us VPN-wise? Is there any way we can set up multiple VPNs with this license?

How to Restrict Single Delivery Date for PO with Multiple Line Items

Dear Experts,
How to Restrict Single Delivery Date for PO with Multiple Line Items.
System needs to through Error Message if User Inputs Different Delivery Dates for PO with Multiple Line Items in ME21N Tcode.
Can we achive this by Some Enhancement in SAP or Not ???
If so how to do it.
Any Inputs is highly appreciated.
Thanks and Regards,
Selvakumar. M

Hi Selvakumar,
we can resrict the PO to have a single delivery date in all the line items by means of giving a error message or overwiting the delivery date keyed/determined in the line item.
You can use the BADI -> ME_PROCESS_PO_CUST. In which you need to implement the method PROCESS_SCHEDULE.
(for technical aid - This method will be called for each and every PO line item, From the imporing parameter im_schedule we can get all the details of current PO line, even we can change the data in the current PO line. )
Regards,
Madhu.

Partial goods receipt for PO with multiple line items

Hello All,
While doing MIGO, for a PO with multiple line items, if one line item is having error, will we be able to go ahead with goods receipt? Or entire material document is blocked for doing MIGO?
We will be doing a development - in case if there is problem in goods receipt (checking of any parameter, and if it is missing - we will be posting error message)...is it possible to ahead with next line item and still post the material document?
If partial goods receipt if possible for PO with multiple line items, how do we do it?
Regards,
RJS

Hi
While doing MIGO, for a PO with multiple line items, if one line item is having error, will we be able to go ahead with goods receipt? Or entire material document is blocked for doing MIGO?
No. You cannot post the MIGO, if even one of the PO line item is having problem or giving error.
We will be doing a development - in case if there is problem in goods receipt (checking of any parameter, and if it is missing - we will be posting error message)...is it possible to ahead with next line item and still post the material document?
If you skip a line irem and do GR with next line item, how will you match quantity & value with the vendor Invoice at LIV ?
If partial goods receipt if possible for PO with multiple line items, how do we do it?
Partial goods receipt is possible for PO line items. That means, if PO has 100 qty for line item 1 then you can do GR for 50 now and 50 later depending on the vendors delivery.
Hope this is what you mean by "Partial Goods Receipt".
Edited by: Arun R on May 10, 2010 2:03 PM

Unable to create PO with multiple line items through LSMW-BAPI method

Hi All,
I have a requirement of creating PO through LSMW. I can't use LSMW standard batch input program since there are some fileds not available and also it has many limitations. I'm using LSMW-BAPI method ( Business object BUS2012) which create IDOC and uses BAPI_PO_CREATE1 to ultimately post the PO in the system. I am trying to create PO from a single file which contains both Header and Item data.
Now my problem is that everytime PO is being created with Single line item only. Everytime I am giving multiple item data in the source file LSMW is preparing multiple IDOCs for multiple line items. As per my understanding this is happenng since header and item is in the same hierarchy level of IDOC type PORDCR102 and the control record is inserted for every line item in the source file.
It seems that through LSMW-BAPI it is not possible to create PO with multiple line items. Can anybody provide some input regarding this? Thanks in advance.
BR,
Atanu Mukherjee

Solved by myself.
Earlier the problem was that LSMW was not being able to recognize items under same header. It was creating new IDOCs every time it gets a new item. To enable this we need to create two structure HEADERDATA and ITEMDATA. Two additional identifier fields with identifier value 'H' and 'I' should be added in these two structures respectively. Then we need one sequential file with the identifiers field followed by the header and Item data. Example:
H~header data
I~item data
I~item data
This would help the standard program to understand what are the items under same header and ultimately create PO with multiple line items.
BR,
Atanu Mukherjee

One order with multiple lines in OM is creating multiple invoices

Application: Oracle 11i (11.5.3)
Modules implemented: GL, OM, AR, AP, PO and CM
Business Requirement:
Our client would like to create Order consisting of multiple lines in Order Management.
The Orders created in OM with multiple lines could be booked, picked, released and transferred
over to Accounts Receivable. On transferring over the Orders from Order Management to Accounts
Receivables using Auto Invoice process the Order should create ONE invoice with multiple lines.
Moreover, for the multiple lines created on an invoice deferred revenue could be applied.
( eg. An order is placed for software and support. The support is to be invoiced all at once but revenue deferred to 1/12
recognized each month as revenue is earned.)
Right now we are getting two invoices. It is putting the deferred revenue item on a seperate invoice. Is this normal
functionality? How can I get both on one invoice.
thanks

Hello Monique,
Well you can have one invoice generated for an order with multiple lines. This is possible by changing some rules in Account Receivables. Use the grouping rules under setups->autoinvoice in AR. You can club your invoices based on any of the columns of ra_interface_lines_all. Hope this works for you.
Arvind

Download to excel with multiple lines in header

Hi experts,
Is there any Funtion module available to download an internal table contents into Local directory of PC with multiple lines in header.
i.e. let us say i hv internal table of 5 entries with 3 columns...
i need to download this 5 entries into an excel file with some texts above the table contents...
For eg : in the below format...
Sample line 1
sample line 2
sample line 3
colheader1 colheader2 colheader3
item1
item2
item3
item4
item5
Please help.
Edited by: Lakshmiraj on Jul 15, 2010 3:26 AM

There is another option of using OLE automation Please check the link below
http://wiki.sdn.sap.com/wiki/display/Snippets/ABAP-OLEAutomationusing+MS-Excel
OR
chek for the example program in Tcode DWDM ( OLE example )
OR
Use FM KCD_EXCEL_OLE_TO_INT_CONVERT ( Fm Uses the same OLE automation)
Hope it helps
Anup

Creating SVG Chart with multiple lines

Hi All,
I want to create a chart with multiple lines.
Ex: I have one emp table with empno, sal and deptno columns.
I want to print deptno in x axis and no of employees on y axis.
I want to print one line for employees with sal > 15000 and one more line for employee with sal =< 15000
So one line will show no of employees with sal more than 15000 for each dept. Similar case for the other line and these 2 lines should be in different colors.
For one line the query will go as
select link, deptno, count(empno)
from emp where sal > 15000 group by null, deptno
Is this possible to draw this chart?
Thanks,
Manoj

I wasn't able to do something like what you describe, but I was able to do this:
I defined column A of the table as a Header Row, selected the cells in the table, and chose this chart type (2D 2 Axis):
Then I clicked the chart and in the pane at the right checked 'Axis Name' in the Axis tab and added the axis names.
Maybe this can give you an idea of how you can illustrate the relationships that you want to show.
SG

7k vPC best practice with multiple line cards?

Similar Messages

Maybe you are looking for