7th generation nano not recognized by computer or iTunes

iTunes not recognicing my new NANO 7th Generation in the Device list in iTunes

diagnostic shows....
**** Device Connectivity Tests ****
iPodService 11.3.1.2 (x64) is currently running.
iTunesHelper 11.3.1.2 is currently running.
Apple Mobile Device service 3.3.0.0 is currently running.
Universal Serial Bus Controllers:
Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27C8. Device is working properly.
Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27C9. Device is working properly.
Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27CA. Device is working properly.
Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27CB. Device is working properly.
Intel(R) 82801G (ICH7 Family) USB2 Enhanced Host Controller - 27CC. Device is working properly.
No FireWire (IEEE 1394) Host Controller found.
Most Recent Devices Not Currently Connected:
iPod nano (4th Generation) running firmware version 1.0.4
Serial Number:       Y(I removed info)
**** Device Sync Tests ****
No iPod, iPhone, or iPad found.
it looks like everything is fine, except it can't find the ipod... why?
when I plug in a thumb drive, it recognizes that, why not the ipod?

Similar Messages

  • Ipod Nano not recognized by computer (or itunes) but charging.. so connected

    worked until this am (though I think I had this once before, a couple years ago, too often follows itunes updates)
    connected to computer (win 7) this morning and it is not recognized by computer (or itunes)
    can't find it looking in Explorer
    but, it is charging so... it is connected
    have tried everything except re-installing itunes... if the computer is not seeing it, and it shows the connection when itunes isn't open...
    would that make any difference?

    diagnostic shows....
    **** Device Connectivity Tests ****
    iPodService 11.3.1.2 (x64) is currently running.
    iTunesHelper 11.3.1.2 is currently running.
    Apple Mobile Device service 3.3.0.0 is currently running.
    Universal Serial Bus Controllers:
    Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27C8. Device is working properly.
    Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27C9. Device is working properly.
    Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27CA. Device is working properly.
    Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27CB. Device is working properly.
    Intel(R) 82801G (ICH7 Family) USB2 Enhanced Host Controller - 27CC. Device is working properly.
    No FireWire (IEEE 1394) Host Controller found.
    Most Recent Devices Not Currently Connected:
    iPod nano (4th Generation) running firmware version 1.0.4
    Serial Number:       Y(I removed info)
    **** Device Sync Tests ****
    No iPod, iPhone, or iPad found.
    it looks like everything is fine, except it can't find the ipod... why?
    when I plug in a thumb drive, it recognizes that, why not the ipod?

  • 7th generation nano not recognized but iphone 5 is recognized with the same cable.

    I just received a 7th generation nano and it is not recognized on my computer.  I used the lighting cable on my Iphone 5 and it detects it fine.  It does not power up or respond to anything.  Did I buy a dud or is there a way to detect it in Windows?  Thanks. 

    There is no way to interact with the phone if the screen is not working.
    Did you happen to have iCloud backup enabled? If so, you'll be able to restore from an iCloud backup and get at least some of your data back.
    ~Lyssa

  • Ipod touch not recognized by computer or ITunes

    Ipod touch is not recognized by computer or Itunes. Tried it on Windows XP OS and also Windows 7. Error message OxE8000068, unknown error, appears. Thanks for any help!

    Try here:
    iPhone, iPad, iPod touch: Unknown error containing '0xE' when connecting

  • My iphone 4s is stuck on connect to itunes, is not recognized by computer or itunes

    my iphone is stuck on the "connect to itunes" loading screen, and when it's plugged into my computer, itunes and the computer are not able to recognize it. when it is plugged in, it gets a "USB device not recognized" and in device manager, it shows up as an "unknown device". I have read and tried everything in http://support.apple.com/kb/TS1538, as well as uninstalling and re-installing itunes and all it's components several times, but nothing has helped. Please help!!!

    The iPhone has gone into recovery mode and you have to restore by connecting to a computer with iTunes and follow the instructions in http://support.apple.com/kb/HT1808.  If you do not have a computer with iTunes, a friend with a computer with iTunes, can you get to an Apple store genius bar and see if the techs will restore for you?

  • I installed a ipod shuffle, named it differently, now my ipod classic is not recognized by computer or itunes.  How do i fix?

    I installed an ipod shuffle with different name.  Now my ipod classic is no longer recognized by computer or itunes.  It appears that Itunes decided that I had replaced the classic with a shuffle.  Classic battery doesnt seem to want to charge, and cannot restore.   
    How do i fix?

    Hello BLTNO,
    Start with this Apple support document related to your issue.  Make sure to work through each and every single troubleshooting step as necessary.
    http://support.apple.com/kb/TS1369
    B-rock

  • Shuffle not recognized by computer nor itunes

    Shuffle not recongnized by computer nor itunes.  I have a brand new edition of itunes.

    Hello obks1984
    Check out the article below to troubleshoot issues with your iPod shuffle not showing up in iTunes. Also make sure that you have the cable plugged in completely to your iPod Shuffle and not just slightly pushed in.
    iPod not appearing in iTunes
    http://support.apple.com/kb/ts3716
    Regards,
    -Norm G.

  • Ipod Nano 7th generation not recognized by computer or iTunes

    Neither my computer nor ITunes recognizes my Ipod nano 7th generation. It was working fine until I ran an intensive AVG PC tuneup on the laptop. Device manager recognizes the Ipod and says it is working correctly. I have done all suggested troubleshooting and nothing has yet worked. Additional suggestions or info I should provide?

    diagnostic shows....
    **** Device Connectivity Tests ****
    iPodService 11.3.1.2 (x64) is currently running.
    iTunesHelper 11.3.1.2 is currently running.
    Apple Mobile Device service 3.3.0.0 is currently running.
    Universal Serial Bus Controllers:
    Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27C8. Device is working properly.
    Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27C9. Device is working properly.
    Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27CA. Device is working properly.
    Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27CB. Device is working properly.
    Intel(R) 82801G (ICH7 Family) USB2 Enhanced Host Controller - 27CC. Device is working properly.
    No FireWire (IEEE 1394) Host Controller found.
    Most Recent Devices Not Currently Connected:
    iPod nano (4th Generation) running firmware version 1.0.4
    Serial Number:       Y(I removed info)
    **** Device Sync Tests ****
    No iPod, iPhone, or iPad found.
    it looks like everything is fine, except it can't find the ipod... why?
    when I plug in a thumb drive, it recognizes that, why not the ipod?

  • Does anyone have problems with the 7th generation nano not being recognized by windows?

    Just got my nano and although it worked the first time I plugged it in to my laptop, it now can not be recognized by Windows, it is completely dead and will not charge at all...anyone else having this issue?

    Hello Chloe
    Start with the first article below to go over some general hardware troubleshooting to get a charge on your iPod nano. If you get that to turn on and you cannot get it to show up on your computer, then the second article should sort you out.
    iPod nano (7th generation): Hardware troubleshooting
    http://support.apple.com/kb/TS4433
    iPod not appearing in iTunes
    http://support.apple.com/kb/TS3716
    Regards,
    -Norm G.

  • My ipod nano 7th generation is not recognized

    my ipod nano 7th generation is getting detected but not recognized . it prompts that i should get latest version of itunes . i tried that but the problem still persists

    im with you
    I got a new laptop a couple months ago, now have a new ipod nano and it wont recognise it. Ive been to genius bar about 3 times on this, they were useless, and didn't really want to bother to spend  time with me, and then went on phone other night for two and half hours to a person in apple ,new mexico, and now last night got a new ipod nano from apple shop and it still wont sync. ive spent hours again reading up on it but it just ownt recognise the device to sync it
    this is getting really frustrating

  • IPod nano 7th Generation will not register in computer

    My iPod 7G has suddenly ceased recognizing any power source. The battery died I went to plug it in and neither the computer or iTunes would not even register that there was anything attached. When I tried to restart and do a hard restore, it would glitch and just continuously restart unless unplugged from power. I have not added any new files that could have altered it.

    Is the Enable Disk Use option enabled from under the iPod's Summary tab in iTunes? If so, disable it and then try restoring again.
    Sometimes simply rebooting the iPod and Mac can resolve the issue. To reset the Nano, press and hold both the Sleep/Wake and Home buttons together long enough for the Apple logo to appear.
    B-rock

  • Ipod nano 7th g is not rcognised by computer after itunes update

    My ipod nano 7th generation is no longer recognised by my computer after the latest itunes update. Newest software is on my windows 8 computer... Any ideas?

    Hello, Arndt262. 
    Thank you for visiting Apple Support Communities.
    If your device is not recognized by iTunes, I would recommend the steps in the article below.  Start with the section labeled Verify that the Apple Mobile Device USB Driver is installed > For Windows Vista, Windows 7, and Windows 8 > Update the Apple Mobile Device Driver.
    iOS: Device not recognized in iTunes for Windows
    http://support.apple.com/kb/TS1538
    Cheers,
    Jason H.

  • 7th gen nano not recognized by windows 8.1 as a drive OR itunes

    When i plug in (USB) my 7th gen nano, my PC (Windows 8.1) doesn't recognize it as a drive (it pops up as a drive for about 2 seconds then goes away) and itunes says its detected but cant be identified properly.  My 4th gen nano connects just fine.

    Hello Quantum222,
    Thank you for the details of the issue you are experiencing with your iPod nano (7th generation) and iTunes.  I reommend reviewing the articles below for the issue you described:
    iPod nano not appearing in iTunes
    http://www.apple.com/support/ipodnano/assistant/itunes/
    iPod not recognized in 'My Computer' and in iTunes for Windows
    http://support.apple.com/kb/TS1369
    Thank you for posting in the Apple Support Communities.
    Best,
    Sheila M.

  • IPod nano does not charge & is not recognized by computer or iTunes

    I have a 1st generation nano 1 GIG.
    It appears "dead."
    It is not recognized by My Computer, iTunes or the Ipod Updater (The updater asks that I connect the iPod, which I do). The iPod diagnostics through iTunes also reports that my iPod is not connected.
    I have tried my iPod on 4 different machines, with one of them having USB 2.0.
    I tried the following from Jeff Bryan. (I don't know if the links from his post have carried over into this post.) So I will list the things I have tried near the end of this post.
    - My iPod won't turn on.
    - iPod battery doesn't charge.
    - iTunes 7 doesn't recognize the iPod.
    - Your Windows PC doesn't recognize iPod.
    - iPod appears in Windows Explorer but does not appear in iTunes.
    - iPod does not appear in iTunes.
    - Fast user switching in Windows XP is not supported.
    I tried resetting my iPod by switching the Hold button on and off and then pressing Menu and the Select button for 6-10 seconds. I have done this over and over and over.
    I have uninstalled the latest iTunes, reboot, reinstall - same problem.
    I have stopped the iPod service, plugged in the iPod, but it isn't recognized by My Computer as stated in the Apple Do-It-Yourself Help. I launched iTunes - same problem.
    I used the window cleanup utility, reboot, reinstall iTunes, connect iPod - same problem.
    I have used the Windows ipconfig utility to change my boot parameters, but still nothing.
    If anyone has any ideas, I would greatly appreciate them.
    My iPod is just shy of 6 months.
    I do have a replacement contract with Best Buy - but I would like to cover all the bases before I succumb to defeat.
    Thanks
    XP Home with USB 1.1   Windows XP   4 machines, all XP, 2 XP Pro, 2 XP Home, 3 have USB 1.1, 1 has USB 2.0, 2 machines have latest iTune

    I'm having the same problem, my ipodnano is about a year old and I can't figure out what to do. I just installed the new itunes on my new laptop with vista premium. I'm desperate for a resolution, do you have any suggestions at all. Any help is greatly appreciated. Thank you

  • IPod Nano not recognized by computer.

    My iPod Nano 2nd generation isn't recognized whatsoever by my computer. A short recap: On a Windows XP driven computer (not mine and on the other side of the Atlantic) I connected and downloaded music. When I returned home, I wanted to connect my iPod to my own Vista driven computer. No can do! My wife has had an iPod Nano 2nd Generation which was previously correctly connected to my computer. To solve my problem(s) I have logged on to my computer with a different user name and installed iTunes with a clean/empty sheet. Still, I haven't been able to connect my iPod. Is there a solution to this? Cheers, Cai

    My iPod Nano 2nd generation isn't recognized whatsoever by my computer. A short recap: On a Windows XP driven computer (not mine and on the other side of the Atlantic) I connected and downloaded music. When I returned home, I wanted to connect my iPod to my own Vista driven computer. No can do! My wife has had an iPod Nano 2nd Generation which was previously correctly connected to my computer. To solve my problem(s) I have logged on to my computer with a different user name and installed iTunes with a clean/empty sheet. Still, I haven't been able to connect my iPod. Is there a solution to this? Cheers, Cai

Maybe you are looking for

  • Help needed - beginner Java programmer using SUN JDK1.5.0

    I have three intacting classes called CalculatorInterface.java which calls methods in Client.java and Account.java. CalculatorInterface-->Client (arrays of objects) c[ ]-->Account (arrays of objects a[ ] linked to c[ ] The problem description : I hav

  • Recover a deleted record in NOARCHIVELOG mode?

    Hello, I'm running 10gR2 in NOARCHIVELOG mode and we do not take backups (please, let's not get into a discussion about this!). I need to know if there is any possible way to recover a record once it has been deleted and a COMMIT has been issued? A u

  • Frame drift on hdcam sr

    Hi I am playing out an HD sequenece at 23.98psf on to a hdcam sr deck from fcp 6.0.1. Although the timecode of the first frame on the sequence drops in at the correct tc on the tape, the end frame is one frame late. This drift seems to occur somewher

  • Assigning table entries to a transport request

    Hi, How can I assign table entries to a request after I have created them? Regards, Vinod.

  • How do you capture a still picture from DVD

    How do you capture a still picture from a DVD