8 lpi in Dot Matrix printer
Hi all,
I have to created a Z format page for a Sapscript form.
The format page was created with width 210 MM and heigth 306 MM.
The format type was created with my format page as atribute and the device type is EPESCP9 EPSON ESC/P 9-pin printer .
Well, here is the problem, when the form is printed the printer don't put the next page in the rigth position, the printer put a big space before begin print the next page.
Inside the configuration of Device type i have the " Printer initialization " with something like that:
reset
\e\0x40
select us-ascii character set
\e\0x52\0x00
set line spacing 6 lpi
\e\0x32
set page length to 12 inch (=78 lines at 6 lpi)
\e\0x43\0x48
cancel bottom margin
\e\0x4f
set left margin to 0
\e\0x6c\0x00
select lq quality
\e\0x78\0x01
select non-proportional spacing
\e\0x70\0x00
someone can help with the codes for may format page ?
thanks.
Hi julio,
I have also faced a similar issue, But now resolved with the printer side page format setting.
You have to change the page format of the printer same as your sap page format.
Please check with the BASIS guy.
Thanks,
Vamshi
Similar Messages
-
Problem with countinuous paper printing in dot matrix printer
Hi All,
I have problem with dot matrix printer (Devise Type EPESCP) while printing continuos printing. If i am printing 2 or more than that prints at a time, 2nd page is printing 5 lines up.
I have developed one smartform for this and i have used A4 size page format.
I have tried to change the Printer initialization code to 86 lines for DINA4. Still no change in continuous printing.
Printer initialization
Reset after exit
Cover page
First Page
Start of even page
Start of odd page
Start of page
End of first page
End of even page
End of odd page
End of page
Start of line on an even page
Start of line on an odd page
Start of line
End of line on an even page
End of line on odd page
End of line
Printer initialization
# reset
\e\0x40
# select character table 3 -> PC 437 character set
\e\0x74\0x03
# set line spacing 6 LPI
\e\0x32
# set page length 86 lines
\e\0x43\0x46
# cancel bottom margin
\e\0x4F
# set left margin to 0
\e\0x6C\0x00
# select LQ quality
\e\0x78\0x01
# select non-proportional spacing
\e\0x70\0x00
Can any one help me.
Thanks,
VishnuHi Vishnu,
Above you have the following commands:
set line spacing 6 LPI
\e\0x32
set page length 86 lines
\e\0x43\0x46
46 HEX = 70
So the above settings mean 70 lines at 6 LPI = 11.66 inches.
So is the paper length 11.66 inches? If not, you should adjust the settings accordingly.
Regards,
Aidan -
PO printing issue in Dot Matrix printer
Hi expert
We got unnecessary spaces on the second page while taking a PO print out.
printer is dot matrix- EPSON LQ2180.
Page Format DINA4
Device type is EPESCP2
Can any body help in this matter?what have i to do remove unnecessary spaces from PO printout?
And also i can not under stand the code which was written in Page Format DINA4?
please find below codes.Help to understand the below code as well.
Printer initialization
reset
\e\0x40
designate codepage for slot 0
\e\0x28\0x74\0x03\0x00\0x00\0x03\0x00
select codepage from slot 0
\e\0x74\0x00
set line spacing 6 LPI
\e\0x32
set page length to DINA4 (=70 lines at 6 LPI)
\e\0x43\0x46
cancel bottom margin
\e\0x4F
set left margin to 0
\e\0x6C\0x00
select LQ quality
\e\0x78\0x01
select non-proportional spacing
\e\0x70\0x00
Thanks
MM
Edited by: samir DODIYA on Feb 28, 2012 1:30 PMThere is something I don't understand: if the barcode printed is visually correct, and exactly the same as with a laser printer, why do you want it would be better with a PDF (especially on a dot matrix printer).
Could you also tell us what symbology you use, and do you use smart form new barcode technology? -
Is there a dot matrix printer that works with iMac
Trying to find an impact printer to do invoices on an imac computer, but no luck so far. Any ideas?
BillThe Epson Networking Impact Printers are designed for high capacity environments and are Mac OS compatible. The IP networking printer drivers built into Mac OS X support the IP Network dot matrix printers, both 9 & 24 pin.
For example, for the FX-890N Networking printer you can use the driver "Epson 9-Pin Series" as shown below:
Epson's full-featured, FX-890N Networking printer offers the durability and ease of use required for essential daily printing. This 9-pin, dot-matrix, narrow-carriage workhorse boasts an MTBF rating of 20,000 power-on hours (POH) and speeds of up to 680 cps (characters per second). Engineered for seamless integration, the FX-890N's interfaces include an internal 10/100 Base-TX Ethernet print server with support for Macintosh OS X.
Its easy-to-install 7.5 million-character ribbon cartridge boosts productivity and ensures a low cost per page, while its 400 million-character print-head life heightens its dependability. Included Epson Remote Configuration Manager software simplifies printer setup and setting selection. Ideal for rugged environments, the printer is a perfect drop-in replacement for the Epson FX-880/880+/980 or Okidata Microline 320/320 Turbo. It handles forms up to seven parts thick via four convenient paper paths, and its redesigned control panel features a lock-out mode and other intuitive functions. The printer is Novell tested and approved and is backed by Epson's comprehensive three-year warranty with technical support. The Epson FX-890N offers the durability and ease of use required for criticaldaily print requirements. Speeds through multipart forms,reports, labels and more at up to 680cps.Offers an MTBF rating of 20,000 POH and a 400 million character print head life.. Includes 10/100Base-TX Ethernet Interface for easy networking.
Printing Method: 9-pin, impact dot matrix
Print Speed:
Ultra Speed Draft: 680 cps (12 cpi); 566 cps (10 cpi)
High Speed Draft: 559 cps (10 cpi)
Draft: 419 cps (10 cpi)
Near Letter Quality: 104 cps (10 cpi)
Characters & Lines
Character Sets:
13 character tables
13 international character sets
Resident Bitmapped Fonts:
Ultra Speed Draft: 10, 12 cpi
High Speed Draft: 10, 12, 15, 17, 20 cpi
Draft: 10, 12, 15, 17, 20 cpi
Near Letter Quality (Roman / Sans Serif): 10, 12, 15, 17, 20 cpi, proportional
Bar Code Fonts: EAN-13, EAN-8, Interleaved 2 of 5, UPC-A, UPC-E, Code 39, Code 128, POSTNET, Codabar (NW-7), Industrial 2 of 5, Matrix 2 of 5
Characters per Line: 80 characters at 10 cpi
Line Spacing: 6 lines per inch default
Formatting:
1/6-inch or programmable in 1/432-inch increments
8 lpi option available on FX-890 Okidata Mode only
Paper Handling
Forms: Continuous multipart, original plus 6 carbonless copies, 1 + 6 copies with pull tractor, maximum thickness .018"
Envelopes:
No. 6 envelopes: 6.5" x 3.6"
No. 10 envelopes: 9.5" x 4.1"
Width:
Single sheets: 3.9" to 10.1"
Continuous: 4" to 10"
Cut-sheet feeder: 7.2" to 8.5"
Length:
Single sheets: 3.9" to 14.3"
Continuous: 4" to 22"
Cut-sheet feeder: 10.1" to 14"
Labels: Minimum: 2.5" x 0.94"
Roll paper: 8.5" width
Paper Feed Speed:
62 millisecond per 1/6"
5" per second, continuous feed
Paper Path:
Manual insertion: Front or rear in, top out
Cut sheet feeder: Top in, top out
Tractor: Front, rear or bottom in, top out
Pull push tractor: Front or rear in, top out
General
Printer Language :
Epson ESC / P
IBM PPDS
Okidata Microline (FX-890 Okidata Mode only)
IP Networking Interface:
EpsonNet 10 / 100Base-TX Ethernet Print Server
Input Buffer : 128 KB
Control Panel: Functions: Font, pitch, pause, tear off, bin selection, line feed, form feed, load, eject, micro adjust, top-of-form adjustment, panel lockout, reset, menu, default setting selection
Sound Level : 55 dB(A) (ISO 7779 pattern)
Rated frequency range : 50 – 60 Hz
Input frequency range : 49.5 – 60.5 Hz
Dimensions : 16.3" x 13.8" x 6.6" (W x D x H) -
BMP image not printing on LIPI Dot MAtrix printer
Hello everybody .
I am facing a promlem while printing a signature ( bmp image ) in a report .
In print preview it is showing coreclty but while printing to LIPI Dot matrix printer model TALLY 2500 that Signature( bmp image ) is not getting printer.
Can anybody let me know wether any setting is to be done from SAP side .
Thanks in advance .
Regards
Dhaval..Hi Raje,
Try to take the print in inkjet or laserjet printer
just for confirmation purpose .
if it prints in that and doesn't print in dot matrix then the problem is with the dot matrix.
In that case ask the basis guys to install the relevent device driver for that dot matrix printer( as normally they would have installed some generic driver ).
Hope this helps.
Regards,
Guru
*mark helpfull answers -
Hi,
My actual job is to create an Report in Oracle Reports 10, running on an IBM AIX Unix Server and direct the output to an Dot-Matrix Printer.
The Report is ready for Preview.
What Parameter should be set as Report_DesFormat for that Dot-Matrix Printer?
I found only the list HTML, HTMLCSS, PDF, RTF, POSTSCRIPT, XML but the Printer can not unterstand any of these formats.
Thanks for any help
Rolf MamatHi.
Using one of graphical destination format can lead to unexpected results. What you should do is to configure your printer at the system OS level. Then you should include that printer into $ORACLE_HOME/guicommon/tk/admin/uiprint.txt file. The line you add to this file should be read as printer_name_you_specified_at_os_level:ASCII:1:some_comment:: For example :
my_dot_printer:ASCII:Testing printer::
Be aware of two colons at the end of the line.
For a destination format you should use one of predefined formats (dflt, wide, ...) or you can make your own format file which should be stored in $ORACLE_HOME/reports/printers directory. And dont forget to define your report design in character units.
Hope this answers your question.
Best regards. -
Print PDF Report(XML) in Dot matrix Printer in Oracle E-Biz R12
Hi Friends,
Is it possible to print a PDF Report (xml report) in Dot Matrix Printer in Oracle E-Biz R12 assuming the Dot Matrix Printer supports Post Script.
If so , what configuration needs to be performed from Oracle E-Biz?
Regards,
DBuser4525564 wrote:
Hi Friends,
Is it possible to print a PDF Report (xml report) in Dot Matrix Printer in Oracle E-Biz R12 assuming the Dot Matrix Printer supports Post Script.
If so , what configuration needs to be performed from Oracle E-Biz?
Regards,
DBI do not think it is possible -- Please confirm with your printer vendor if your printer support PDF printing first.
Thanks,
Hussein -
Is it possible to connect a dot matrix printer to MacBook Air? I need to print receipts in my textile showroom. Please suggest good applications for printing receipts and saving daily sales records.
Prath33k wrote:
Is it possible to connect a dot matrix printer to MacBook Air?
yes. As long as it is a newer one (means not 15-20 years old). Do you have one? If so, provide the make/model. If you do not have one, which ones are you looking to purchase? -
Dot matrix printing on 15 x12 inch paper
Hi
I have created report for purchase register
Report is so large to print
so i have desiged this report in PDL for dot matrix printer and paper size 15 inch x 12 inch.
When i going to print this report, i not get proper print out
Please tell me the setting regarding to print this report on dot matrix 15 x 12 inch continous paper.
Regds
KishorHI
Thanks for you valuable suggestion
Printer at my end is not supported by SAP B1
ok
what is use of Function grouplinenum() in PLD
I wants the follwing output
docnum, Acct Code, Acct_total document_total
1 xyz1 500 1100
xyz2 600
2 abc1 1000 2000
abc2 500
abc3 500
Total 3100 3100
Please study the following query for above and Please tell me it is possible to design PLD
SELECT A.SERIESNAME, A0.DocType, A0.DocNum, A0.DocDate, A0.NumAtCard, A0.TaxDate,
A0.CardCode, A0.CardName, A1.City,
A2.TaxId11, A2.TaxId1, A2.TaxId2,
A4.TAXTYPE, A4.VATRATE, A4.vattaxable, A4.Totvat,
A0.DOCTOTAL, A0.WTSUM,
A5.TAXCODE, A5.formatcode, A5.ACCTNAME, A5.ACTOTAL,
(case when TAXTYPE IS NULL then A0.DOCTOTAL + A0.WTSUM ELSE 0.00 END) AS LabourChrg,
(case when TAXTYPE IS NOT NULL
then A0.DOCTOTAL + A0.WTSUM - ISNULL(A4.VATTAXABLE, 0.00) - ISNULL(A4.TOTVAT, 0.00) ELSE 0.00 END) AS LabourChrg
FROM NNM1 A
INNER JOIN OPCH A0 ON A.SERIES = A0.SERIES
LEFT OUTER JOIN CRD1 A1 ON A0.CARDCODE = A1.CARDCODE AND A1.LINENUM = 0
LEFT OUTER JOIN CRD7 A2 ON A0.CARDCODE = A2.CARDCODE
LEFT OUTER JOIN
(SELECT C0.DOCENTRY,
MAX(case when C1.nftaxid = -7 then 'L' when C1.nftaxid = -4 then 'C' else 'O' end) as TAXTYPE,
MAX(C0.TAXRATE) as VATRATE, SUM(C0.TAXSUM) as TOTVAT, SUM(C0.BASESUM) as VATTAXABLE
FROM PCH4 AS C0, OSTT AS C1
WHERE C1.ABSID = C0.STATYPE
AND C1.nftaxid in (-7, -4)
GROUP BY C0.DOCENTRY) A4 ON A0.DOCENTRY = A4.DOCENTRY
INNER JOIN
(SELECT E0.DOCENTRY, E0.TAXCODE, E1.formatcode, E1.ACCTNAME, E0.ACTOTAL
FROM
(SELECT D0.DOCENTRY, D0.TAXCODE, ISNULL(D1.ACCTCODE, D0.ACCTCODE) AS ACCTCODE,
SUM(D0.LINETOTAL + D0.LINEVAT + D0.DISTRIBSUM + D0.STCKDSTSUM) AS 'ACTOTAL'
FROM PCH1 D0 LEFT OUTER JOIN PDN1 D1
ON D0.BASEentry = D1.DOCENTRY AND D0.BASELINE = D1.LINENUM
GROUP BY D0.DOCENTRY, D0.TAXCODE, ISNULL(D1.ACCTCODE, D0.ACCTCODE)) AS E0
INNER JOIN OACT E1 ON E0.ACCTCODE = E1.ACCTCODE) A5
ON A0.DOCENTRY = A5.DOCENTRY
WHERE A.SERIESNAME ='[%0]'
ORDER BY DOCNUM
Thanks -
Sales invoice Smartform printing in dot matrix printer in sucession
Dear all,
I am trying to Print Sales invoice on Dot matrix Printer.
My First Invoice is printed ok, but if i try to print second invoice without manually adjusting the paper the alignment on printer goes haywiered.
Do we have some option in smartform where we can trigger new page command.
Regards,
Gaurav SoodHi Amiya,
you need to check the paperformat which is used. I'm pretty sure that there is a wrong paperformat selected. The supported paperformats are published in the official documentation of the printer-model.
~Florian -
Problem with custom paper size on dot matrix printer
Hi All,
I'm using CR2008 with updated to SP2. I have a problem with custom paper size (W=21; H=14), the CR Viewer show report with custom paper size correctly but when I print it to a dot matrix printer (Epson LQ 300+) the content was rotated to landscape. If print to a laser printer the content was printed correctly. My report was printed correctly by CR10 or previous versions I got this issue when upgraded to CR2008. I aslo tested my computer and printer with orther application like MS Word the printing have no problem with custom paper size.
Thanks for any advice for me.
HanLooking at the Epson LQ 300+ driver, I see that the latest update is from 2002. In my experience, most matrix printer drivers are not unicode. Crystal Reports is designed to only work with unicode printer drivers. See the [How Printer Driver Options Affect a Report|https://www.sdn.sap.com/irj/boc/index?rid=/library/uuid/a09051e9-721e-2b10-11b6-f9c65c64ef29&overridelayout=true] article, page 6 for details. Also, see [this|https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/oss_notes_boj/sdn_oss_boj_dev/sap(bD1lbiZjPTAwMQ==)/bc/bsp/spn/scn_bosap/notes.do] note.
Finally, see if you can print from the CR designer to this printer and if you get the correct results here.
Ludek -
Need to Take Fast Printing on Dot Matrix Printer Using Report 10g
Dear ,
I need to take a fast output of Oracle 10g reports on Dot Matrix printer
Client runs the report and open in PDF but when he takes hard copy on his/her local printer, then printer works very slow and take huge time to print a single page.
Kindly help me, how can client get the output directly on his locally attached Dot Matrix Printer and fast.
Reports desinged and compile in Report10g R2 and
Middle teir using =Application Server 10 R2.
Thanks and regards.
PriyaDraft mode is not by font. It is a specific printer mode. If you can not manually setup the mode, B1 may not have any abilities to print in this mode.
Thanks,
Gordon -
SAP B1 not printing on Dot Matrix Printer
Hello everyone
I'm trying to print from SAP B1 2007B PL:00 to a Dot Matrix Printer connected in network.I selected the printer and gave print.But it is printing one or two junk characters only.When i try the same in a laser printer it prints well. What might be the problem and solution for this
Thanks and regards
RaghuHi
The following dot-matrix printers are supported by SAP Business One.
+ Citizen PROdot 300
+ Epson FX-880
+ OKI MICROLINE 320 Elite
If you are using the 2005 version you can use also the Epson FX-890.
Paulo Calado
SAP Business One Forums Team -
Page not printing on Dot Matrix Printer
Dear Experts,
I had requirment to print the PO layout on a stationary which is bigger than a4 and bit lesser than a3
I found that page as 370(Width) and 295(hight). So according to it I created a new page format in SAP coz I didnt have any page format near to it. For setting up the new page format I did these steps:
1) Page Format
2) Format Types
3) Device Types.
All these are done. also I have attached my Z smartform in the NEU output type in NACE.
Now when I excute SF and try to print that its not getting triggering on the printer.
I have taken printer as LP01.
Please suggest. Where I am wrong.
-=Soni=-Hi,
You need to assign the created page format to the device type used. Which device type is defined in output device LP01? Also if it is a device type with Line Printer Driver II, you also need to add the commands in the Printer Initialization action of the page format within the device type with commands to tell the printer the length of the page.
See the thread Re: DOT MATRIX PRINT is not coming correctly
Regards,
Aidan -
Crystal Report printing on dot-matrix printer
Hello,
I've developed an application using VB.NET and Crystal Reports in VS2008. The report generated gets printed correctly on modern laser or inkjet printers. However, the entire formatting gets affected when I print these reports on dot matrix printer. Apart from that. the print speed is very slow. I tried exporting the report to PDF, DOC and other formats - but no solution. There was Export to Text function, which is not working in Crystal Reports now.
After a research on this issue, I found out few links to some solutions - which actually doesn't work. These links are as follows:
http://social.msdn.microsoft.com/forums/en-US/vscrystalreports/thread/e24a8084-ad53-48bc-a7d5-065ef82636ac
http://social.msdn.microsoft.com/Forums/en-US/vscrystalreports/thread/dd506c66-4cdc-48a7-9fa8-2c6f14daef24/ (Same issue in C#)
I've seen some software, in which, when Print on Dot Matrix (custom menu option) is selected, data is sent to DOS mode and reports are printed from DOS mode.
Is there any solution for this? OR DOS mode is the only solution?
This is high priority issue. Even though we're moving ahead in IT industry, govt. still depend on 4 color dot matrix printer reports.
Waiting for solution
Regards
Mayur Tendulkar | www.mayurtendulkar.comAlso, as of Service Pack 3 Microsoft updated their security models so a new C++ runtime is required. Please see these Kbase articles and Forum posts for more info:
https://bosap-support.wdf.sap.corp/sap/support/notes/0001495319
Forum thread for info Setup And Deployment Problem
Info:
Microsoft Visual C++ 2005 Service Pack 1 Redistributable Package ATL Security Update and is available using the link below.
This needs to be installed before installing a setup package that uses the SP 3 merge modules.
http://www.microsoft.com/downloads/details.aspx?familyid=766a6af7-ec73-40ff-b072-9112bab119c2&displaylang=en
Thank you all again and have a great day
Don
Maybe you are looking for
-
Permanently changing parameters on the search box?
I just switched over to Leopard from Tiger at work. Whenever I do searches for files in the finder my three parameters at the top are "Name", "Kind" and "Last Opened". I'm trying to find a way to change the "Last Opened" to "Last Modified" as it was
-
Can a restore be reversed on an iphone
on iphone can a restore be reversed?
-
HI I have 4 node cluster running in red hat linux 5 - oracle 10 g rel2 4 Database are running A , B , C,D Instancese are running like this first node A1 & D1 second node B2 & C2 third node B3 & C3 fourth node A4 & D4 I AM getting a lot of trace file
-
Win 98 version of Developer??
I am taking a college course in Oracle. I already downloaded and installed 8i Personal Edition but now I need to use Forms. All I have found on the OTN web site are versions for Win NT. Are there any 98 versions or will the NT download work on 98? I
-
The column browser disappears when i try to resize it
This is weird. If I open iTunes, I can adjust the size of the column broser by grabbing the bar and dragging it up and down (to see more or less artists, etc). However, when I start playing a song and try to do this, the column browser animates awa