802.11i Supported by Cisco Wireless Products?
Hello all,
Got a customer looking to install a wireless network however does not wish to do this unless the units support 802.11i.
Are there any routers/cards that support this that I can recommend?
Thanks,
Leon
There is no Cisco hardward supports 802.11i yet. There is a plan for Cisco to provide 802.11i. I am told not to disclose any future new hardward and new feature information. You need to talk to the local Cisco account team.
Similar Messages
-
Interoperability of cisco wireless products?
I've been doing a lot of research on various Cisco wireless products and the options are kind of confusing.
I'll start with my deployment; I have two locations both of which have a manufacturing and warehouse environments (no climate control) and regular offices.
Location 1 needs 3 APs on the production floor and 1 in the offices.
Location 2 needs 5 APs on the warehouse floor and 4 for the offices.
I was thinking about using the Cisco 521 APs for both the production floor and offices and the Cisco 526 Wireless Controller for Location 1. I figure that will give them room for expansion and keep the costs low.
For location 2 I was thinking about the Aironet 1240AG APs for the warehouse floor, Aironet 1140AG APs for the offices and then a Cisco 2112 Wireless Controller to manage all the APs.
Both locations require WPA (or WPA2) encryption and roaming.
My questions are:
Will the 521 APs work with the 2112 controller? For that matter, what sort of interoperability is there with the APs and controllers? Can I manage any Cisco AP with any Cisco Controller?
Are there any cheaper APs than the 1140AG that will work with the 2112 controller?
Is the 1240AG a good choice for a non-climate controlled warehouse environment? The APs are going to be mounted on the ceiling which is roughly 50 feet high and I'm going to be very upset if I deploy these APs and then have one fail during the summer 6 months later because it wasn't made for volatile environments.
The 521 APs are only going to be about 15 feet up so they can be accessed with a ladder so I'm not so worried about them.
Thanks!Will the 521 APs work with the 2112 controller?
No.
Are there any cheaper APs than the 1140AG that will work with the 2112 controller?
You could try the 1130. 1140 supports 802.11n while 1130 is a/b/g only.
Is the 1240AG a good choice for a non-climate controlled warehouse environment?
The 1240, like the 1130, supports a/b/g only while the 1250 supports a/b/g/n. The newer 1260 is controller-based only. The 1240, 1250 and 1260 use external antennae that's an OPTION. -
Cisco Wireless against Linksys WAP200-AS
Hi,
I need to position Cisco wireless product against Linksys WAP200-AS,the distance between the two buildings being 100mts.
Kindly suggest a suitable model no.
Thanks!The Cisco Aironet 1300 Series Outdoor Access Point
-
Sales material for Cisco Wireless
Does anyone knows where i can get access to some online resources for Cisco Wireless products / technology??
Would appreciated any help.Hi Friend,
just try the Cisco Homepage. Strat from here:
http://www.cisco.com/en/US/products/hw/wireless/index.html
Best regards,
Frank -
Apple left out support for 802.11i, secure wireless networking WAP2
We just bought this iMac from Apple in July, and I'm very unhappy that Apple designed the AirPort networking for one generation earlier security with wireless networking.
The 802.11i standard, which supports very secure WAP2 without the need for a Radius Server (I believe 802.11i refers to this as personal mode) was adopted by the IEEE in 2004.
Apparently, 2 years isn't enough time for Apple to get the correct chipset into the computer. This system supports the earlier standards only, WAP and WEP. To achieve the newer standard requires a different chipset in the AirPort hardware. Apple supports 802.11i in the stand-alone AirPort gateways, and may support it in the newer Intel Core 2 Duo systems as well. Grumble, grumble, grumble.
For Apple marketing and customer support folks reading this, I'd appreciate your thoughts and suggestions on fixing this.
iMac Intel Core Duo 17" Mac OS X (10.4.8)
iMac Intel Core Duo 17" Mac OS X (10.4.8)"I can find no indication of an Apple AirPort product that says it is capable of WPA2"
mrwheels,
You sound like someone looking for an argument. I'm not sure what the relevance of your statement really is, and I've also never heard of 802.11i. The only standards I've heard of are "b" and "g," not "i." Why don't you fill me in, as I've been using WPA2 since earlier this year? I believe my system automatically updated to it from WPA during one of the software updates, I think it was 10.4.6 in April, as I specifically recall having one iMac that was encrypted with WPA while another had WPA2. There was some sort of temporary issue that occurred with that setup, but, unfortunately, I can't remember what it was, since it lasted such a short time (the few minutes until I installed the update on the second iMac, as I recall).
Since the update was not a problem for me, the job of reading the update read-me's to determine exactly when it occurred will have to fall to you. In addition, if you look back at these discussion threads during the time from Jan to April, you will see that there were a goodly number of users who were having severe AirPort connection problems with their Core Duo iMacs. I wasn't one of them. They ALL reported having their problems resolved with the installation of the 10.4.6 software update.
I am using WPA2 on my four 20-inch Core Duo iMacs [purchased at three different times from two different Apple sources] as well as my G4 iBook and other Macs. They have been using WPA2 on both an AirPort Express base station network, and, at a different location, on an AirPort Extreme base station network, both of which are more than two years old. No matter what Apple's printed materials disclose, WPA2 is in fact supported.
"Apple is selling products that are 2 years behind in supporting a critical wireless security standard"
Based on what I've stated, and the fact that there are many Discussions members also using WPA2 with their AirPort base stations, that is baloney:))
Message was edited by: myhighway -
Which cisco wireless bridges support point to multipoint
hi all i am really new to wireless. i am looking for information as which cisco wireless bridges support point to multipoint configuration.
i have a cisco 1230G access-point will it support the same .
any help would be great.
regards
sushilThe Cisco 1300's and 1400's support point-to-point and point-to-multipoint. The 1230G can only support point-to-point (i think)
http://www.cisco.com/en/US/products/hw/wireless/ps441/products_qanda_item09186a0080094644.shtml#q20 -
Wireless Network is slow after putting cisco wireless controller
Hello Guys,
My wireless network was very good before putting Cisco WLC 4402 with version 3.2.171.6.
In my network there are two SSID's one for official and another for guest, which is working one single LAP 1142.( Total 12 LWAP is here)
we decided to manage all the ap and deployed WLC but now wireless network is very slow, local gateways is pinging with 80 ms. before WLC it was 1 ms.
Pls. suggest or come up with question to reach a solution.
reg
sanjeevHi,
yah it's gigabit support and i have connected with fibre patch cord.
My SWITCH port config is below.
interface GigabitEthernet1/0/25
switchport trunk encapsulation dot1q
switchport mode trunk
Controller sh run
System Inventory
Switch Description............................... Cisco Controller
Machine Model.................................... AIR-WLC4402-12-K9
Serial Number.................................... FOC1105F01E
Burned-in MAC Address............................ 00:1A:6D:DD:23:00
Crypto Accelerator 1............................. Absent
Crypto Accelerator 2............................. Absent
Power Supply 1................................... Absent
Power Supply 2................................... Present, OK
Press Enter to continue Or to abort
System Information
Manufacturer's Name.............................. Cisco Systems, Inc
Product Name..................................... Cisco Controller
Product Version.................................. 3.2.171.6
RTOS Version..................................... 3.2.171.6
Bootloader Version............................... 3.2.171.6
Build Type....................................... DATA + WPS
System Name...................................... SFA-CTRL2-HQ
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.14179.1.1.4.3
IP Address....................................... 10.156.11.231
System Up Time................................... 0 days 11 hrs 9 mins 43 secs
Configured Country............................... United States
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +38 C
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 4
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 115
Press Enter to continue Or to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
Current LWAPP Transport Mode..................... Layer 3
LWAPP Transport Mode after next switch reboot.... Layer 3
FIPS prerequisite features....................... Disabled
Press Enter to continue Or to abort
Network Information
RF-Network Name............................. UNISFA
Web Mode.................................... Enable
Secure Web Mode............................. Enable
Secure Shell (ssh).......................... Enable
Telnet...................................... Enable
Ethernet Multicast Mode..................... Disable Mode: Ucast
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
ARP Unicast Mode............................ Disabled
Cisco AP Default Master..................... Disable
Mgmt Via Wireless Interface................. Enable
Bridge AP Zero Config....................... Enable
Bridge Shared Secret........................ youshouldsetme
Allow Old Bridging Aps To Authenticate...... Enable
Over The Air Provisioning of AP's........... Enable
Mobile Peer to Peer Blocking................ Disable
Apple Talk ................................. Disable
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Fast SSID Change ........................... Disabled
Press Enter to continue Or to abort
Port Summary
STP Admin Physical Physical Link Link Mcast
Pr Type Stat Mode Mode Status Status Trap Appliance POE
1 Normal Forw Enable Auto 1000 Full Up Enable Enable N/A
2 Normal Disa Enable Auto 1000 Full Down Enable Enable N/A
Press Enter to continue Or to abort
AP Summary
AP Name Slots AP Model Ethernet MAC Location Port
AP_MHQ_CMS_OFFICE 2 AIR-LAP1242AG-A-K9 00:19:30:76:75:42 default location 1
AP01-MHQ-HOM 2 AIR-LAP1242AG-A-K9 00:19:30:76:74:be default location 1
AP01_MHQ_AIROPS 2 AIR-LAP1242AG-A-K9 00:1d:45:36:6c:84 default location 1
AP01_MSA_HOM_RES 2 AIR-LAP1242AG-A-K9 00:1d:45:36:6b:e2 default location 1
AP10-MHQ-CCITS 2 AIR-LAP1242AG-A-K9 00:19:30:76:74:82 default location 1
AP01-MSA2-TC5 2 AIR-LAP1242AG-A-K9 00:1d:45:36:6d:44 default location 1
AP01_MSA_CableTV_Room 2 AIR-LAP1242AG-A-K9 00:19:30:76:83:aa default location 1
AP01_MSA_RUS_ROOM 2 AIR-LAP1242AG-A-K9 00:19:30:76:83:00 default location 1
AP01-MHQ-JLOC 2 AIR-LAP1242AG-A-K9 00:19:30:76:7f:d0 default location 1
AP01-MSA-C2-D 2 AIR-LAP1242AG-A-K9 00:19:30:76:74:90 default location 1
AP01_MSA_DA7 2 AIR-LAP1242AG-A-K9 00:19:30:76:80:38 default location 1
AP01_MSA_CMS_RES 2 AIR-LAP1242AG-A-K9 00:19:30:76:83:f0 default location 1
Press Enter to continue Or to abort
AP Config
Cisco AP Identifier.............................. 1
Cisco AP Name.................................... AP_MHQ_CMS_OFFICE
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:75:42
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.240
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1107B3U8
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211g
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1a:a2:d9:d3:60
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 1
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 1
Cisco AP Name.................................... AP_MHQ_CMS_OFFICE
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:75:42
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.240
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1107B3U8
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1a:a2:d9:d3:60
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
9000 Kilo Bits........................... MANDATORY
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 4
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 17 dBm
Tx Power Level 2 .......................... 15 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 24
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 2
Cisco AP Name.................................... AP01-MHQ-HOM
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:74:be
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.238
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1107B3W4
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211g
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1a:30:e7:fc:30
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 2
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 11
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. Side A or Right Connector
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 2
Cisco AP Name.................................... AP01-MHQ-HOM
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:74:be
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.238
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1107B3W4
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1a:30:e7:fc:30
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
9000 Kilo Bits........................... MANDATORY
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 4
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 17 dBm
Tx Power Level 2 .......................... 15 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... AP01_MHQ_AIROPS
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:36:6c:84
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.232
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1135B2X7
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211g
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:46:7e:d9:60
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 6
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. Side A or Right Connector
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... AP01_MHQ_AIROPS
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:36:6c:84
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.232
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1135B2X7
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:46:7e:d9:60
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
9000 Kilo Bits........................... MANDATORY
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 4
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 17 dBm
Tx Power Level 2 .......................... 15 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 4
Cisco AP Name.................................... AP01_MSA_HOM_RES
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:36:6b:e2
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.239
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1135B2X1
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211g
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:46:7e:d4:30
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 11
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 4
Cisco AP Name.................................... AP01_MSA_HOM_RES
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:36:6b:e2
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.239
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1135B2X1
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:46:7e:d4:30
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
9000 Kilo Bits........................... MANDATORY
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 4
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 17 dBm
Tx Power Level 2 .......................... 15 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 149
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 5
Cisco AP Name.................................... AP10-MHQ-CCITS
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:74:82
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.233
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1107B3TJ
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211g
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1a:30:e7:fa:60
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 1
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 5
Cisco AP Name.................................... AP10-MHQ-CCITS
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:74:82
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.233
IP NetMask......... -
Cisco Wireless Location Appliance
dear
i have WCS with 500 ap License
i need to have Cisco Wireless Location Appliance what lisens i need for 500 ap
please explain to me thatHi Ahmed,
This is the upgrade License SKU for upgrading WCS to WCS Location;
WCS-LOC-UPG-K9
Supports deployment of Cisco WCS on a single server only.
For customers upgrading from their existing Cisco WCS base licenses to equivalent Cisco WCS location licenses running Cisco WCS Software Release 4.1 or later.
Available as Cisco WCS location in increments of 50, 100, or 500 lightweight access points.
Customers currently using this license with Cisco WCS Software Release 4.0 are encouraged to upgrade to Cisco WCS Software Release 4.1, but they are not required to do so.
Order the Correct Cisco WCS SKUs
The process to order Cisco WCS SKUs for WCS-STANDARD-K9, WCS-LOC-UPG-K9, WCS-WLSE-UPG-K9 and WCS-ENT-K9 is presented below. To request help with ordering, please contact Cisco Customer Service: http://www.cisco.com/go/customerservice.
1. Login to the Cisco Ordering Tool.
2. Enter the family SKU of WCS-STANDARD-K9 or WCS-LOC-UPG-K9 or WCS-WLSE-UPG-K9 or WCS-ENT-K9 into "Enter Product" in the Ordering Tool and then press "Enter."
3. The family SKU will display in the ordering area. (Figure 6).
4. Select the "Line" for the family SKU
5. Once you have been taken to the configuration screen, select one of these options from the left side (Figure 7):
For WCS-STANDARD-K9 select one of the sub-SKUs based on the following:
Base: WCS Standard AP Base Option
Location: WCS Standard AP Location Option
For WCS-WLSE-UPG-K9 select one of the sub-SKUs based on the following:
Base: WLSE to WCS AP Base Upgrade Option
Location: WLSE to WCS AP Location Upgrade Option
**For WCS-LOC-UPG-K9 select the sub-SKU:
**WCS AP Location Upgrade Option
For WCS-ENT-K9 select the sub-SKU:
WCS Enterprise AP Location Option
For the WCS-STANDARD-K9 or **WCS-LOC-UPG-K9 SKU families, customers are prompted to order the optional CD (WCS-CD-K9), for a nominal charge, during the ordering process. The WCS-CD-K9 contains one software image of Cisco WCS Software Release 4.1 on a CD for Windows and Linux. This CD is shipped by U.S. mail to the purchaser's address. The optional CD is not available for WCS-WLSE-UPG-K9 because this SKU family already ships in CD format.
6. The right side of the screen will display the licenses available (Figure 7). The price for each SKU is displayed in the Ordering Tool.
7. Each license is orderable in a quantity of one (1) for the quantity blocks specified. To add multiple quantities of license blocks, you must go back to the main screen and order additional family SKUs and then select the sub-SKU option and license quantity block required. Repeat this process as needed, until the correct quantity of license blocks for your sub-SKU have been ordered.
From this good doc;
http://www.cisco.com/en/US/products/ps6305/pro ducts_data_sheet0900aecd804b4646.html
Hope this helps!
Rob -
Cisco Wireless AP 2602 - Web Authentication/Pass NOT working?
Product/Model Number:
AIR-CAP2602E-A-K9
Top Assembly Serial Number:
System Software Filename:
ap3g2-k9w7-xx.152-4.JB3a
System Software Version:
15.2(4)JB3a
Bootloader Version:
BOOTLDR: C2600 Boot Loader (AP3G2-BOOT-M) LoaderVersion 12.4(25e)JA1, RELEASE SOFTWARE (fc1)
When "Web Authentication/Pass" option checked, it is totally unaccessible to internal or external network, any clue/advice?
Thanks in advance.Thanks, seems I missed the RADIUS part; after I done that it's still no luck, here are some tech support info, are you able to help?
------------------ show version ------------------
Cisco IOS Software, C2600 Software (AP3G2-K9W7-M), Version 15.2(4)JB3a, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Mon 23-Dec-13 08:11 by prod_rel_team
ROM: Bootstrap program is C2600 boot loader
BOOTLDR: C2600 Boot Loader (AP3G2-BOOT-M) LoaderVersion 12.4(25e)JA1, RELEASE SOFTWARE (fc1)
WuGa-CiscoAP uptime is 3 days, 19 minutes
System returned to ROM by power-on
System restarted at 23:18:39 +0800 Mon Feb 10 2014
System image file is "flash:/ap3g2-k9w7-mx.152-4.JB3a/ap3g2-k9w7-xx.152-4.JB3a"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-SAP2602E-A-K9 (PowerPC) processor (revision A0) with 204790K/57344K bytes of memory.
Processor board ID FGL1650Z5X3
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: E0:2F:6D:A3:4D:0B
Part Number : 73-14511-02
PCA Assembly Number : 800-37898-01
PCA Revision Number : A0
PCB Serial Number : FOC164889AN
Top Assembly Part Number : 800-38357-01
Top Assembly Serial Number : FGL1650Z5X3
Top Revision Number : A0
Product/Model Number : AIR-CAP2602E-A-K9
Configuration register is 0xF
------------------ show running-config ------------------
Building configuration...
Current configuration : 5276 bytes
! Last configuration change at 23:36:14 +0800 Thu Feb 13 2014
! NVRAM config last updated at 23:36:14 +0800 Thu Feb 13 2014
! NVRAM config last updated at 23:36:14 +0800 Thu Feb 13 2014
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname WuGa-CiscoAP
logging rate-limit console 9
enable secret 5
aaa new-model
aaa group server tacacs+ tac_admin
aaa group server radius rad_eap
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login webauth group radius
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authentication login web_list group radius
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
clock timezone +0800 8 0
no ip cef
ip admission name webpass consent
ip admission name webauth proxy http
ip admission name webauth method-list authentication web_list
ip admission name web_auth proxy http
ip admission name web_auth method-list authentication web_list
ip admission name web-auth proxy http
ip admission name web-auth method-list authentication web_list
ip name-server 8.8.8.8
dot11 syslog
dot11 vlan-name GuestVLAN vlan 2
dot11 vlan-name InternalVLAN vlan 1
dot11 ssid Guest
vlan 2
web-auth
authentication open
mbssid guest-mode
dot11 ssid WuGa-6
vlan 1
authentication open
authentication key-management wpa
mbssid guest-mode
wpa-psk ascii 7 0211115C0A555C721F1D5A4A5644
dot11 ssid WuGa-60
vlan 1
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 03084C070900721F1D5A4A56444158
dot11 guest
username wuga lifetime 360 password 7 030D5704100A36594908
username Cisco privilege 15 password 7
bridge irb
interface Dot11Radio0
no ip address
encryption mode ciphers aes-ccm
encryption vlan 1 mode ciphers aes-ccm
ssid Guest
ssid WuGa-6
antenna gain 2
stbc
mbssid
speed basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. m16. m17. m18. m19. m20. m21. m22. m23.
channel 2452
station-role root
dot11 dot11r pre-authentication over-air
dot11 dot11r reassociation-time value 500
ip admission web-auth
interface Dot11Radio0.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.2
encapsulation dot1Q 2
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 spanning-disabled
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
ip admission webauth
interface Dot11Radio1
no ip address
encryption mode ciphers aes-ccm
encryption vlan 1 mode ciphers aes-ccm
ssid WuGa-60
antenna gain 4
peakdetect
no dfs band block
stbc
speed basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. m16. m17. m18. m19. m20. m21. m22. m23.
power local 5
channel width 40-above
channel dfs
station-role root
dot11 dot11r pre-authentication over-air
dot11 dot11r reassociation-time value 500
interface Dot11Radio1.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface GigabitEthernet0
no ip address
duplex auto
speed 1000
interface GigabitEthernet0.1
encapsulation dot1Q 1 native
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.2
encapsulation dot1Q 2
bridge-group 2
bridge-group 2 spanning-disabled
no bridge-group 2 source-learning
interface BVI1
ip address 192.168.133.213 255.255.255.0
ip default-gateway 192.168.133.200
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip route 0.0.0.0 0.0.0.0 192.168.133.200
ip radius source-interface BVI1
ip access-list extended ALL
permit ip any host 0.0.0.0
permit ip any any
permit ip 0.0.0.0 255.255.255.0 any
ip access-list extended All
permit tcp any any established
permit tcp any any eq www
permit ip any any
radius-server local
nas 192.168.133.213 key 7 070C285F4D06
radius-server attribute 32 include-in-access-req format %h
radius-server vsa send accounting
radius server 192.168.10.2
address ipv4 192.168.10.2 auth-port 1812 acct-port 1646
radius server local
address ipv4 192.168.133.213 auth-port 1812 acct-port 1813
key 7
bridge 1 route ip
line con 0
terminal-type teletype
line vty 0 4
terminal-type teletype
transport input all
sntp server 128.138.141.172
sntp broadcast client
end -
Can anyone help? All I want to do is enable 802.11b support on my Cisco 877W. My 802.11g clients can see and attach to it no problems. My 802.11b clients cannot see it at all. I have tried all sorts but nothing has helped. My config looks like this:
interface Dot11Radio0
no ip address
encryption key 1 size 128bit 7 BC48CE99C4E9B683819990D3C1A5 transmit-key
encryption mode wep mandatory
ssid *****
authentication open
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0
48.0 54.0
station-role root
no dot11 extension aironet
bridge-group 1
bridge-group 1 spanning-disabled
What do I need to add to make it visible and available to 802.11b clients?
Many Thanks,
MattI'd start by defaulting the AP back to factory default, no WEP, no authentication.
Check to see if the 802.11b clients can connect.
If all the 802.11b clients are running the same software, check to see that they are up-to-date drivers & client software. If you're using the MS client software (Zero Wireless Config) try a client using the vendor's client software instead.
If the clients are not eve associating, look at the basic parameters: things like preamble length (legacy default is "long" which is a one meg data rate)
If you can get the 802.11b client to connect whith all open parameters, then add WEP. Be advised that some clients need the WEP entered as HEX, not ASCII.
For example ASCII "ABCD" would be "41 42 43 44" in hex ... make sure you're using the same system. IF youre using something like "12345abcde" that can be a valid (but incorrect) hex string when ou really intend for it to be ASCII.
Also note that leading or training spaces (ASCII 20) are valid characters. Make sure you do not have leading or training spaces in your WEP (unless you really want them there, in whch case, make sure they're there)
Make sure the Ethernet format is correct: use the Web GUI to set up. Check the parameters on the "Interfaces" page and do not (at least initially) use the "Best throughput" or "Best Range" settings, leave it at "Default Settings"
If your 802.11b clients are PDAs, bar-code scanners, or other hand-held devices, check that they are at default settings for the standard 802.11b protocols; some use proprietary protocols for better performance or security.
That's about it for me ... let us know if any of that changes (works / doesn't work, but acting differently / doesn't work, looks the same).
Good Luck
Scott -
Clarification on 802.1x support for 3560
Hi all: have a question on support of 802.1x support in 3560.
This (http://www.cisco.com/en/US/products/hw/switches/ps5528/products_configuration_guide_chapter09186a00801e85c4.html) one talks about 802.1x configuration on a 3560 with 12.1(19)EA1
But this tool http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp tells me that IEEE 802.1x-VLAN Assignment is supported only on ED Releases 12.2(25)SEE1, 12.2(25)SED1, 12.2(25)SEC2, 12.2(25)SEB4, 12.2(25)SEA, 12.2(25)SE for 3560.
Does this mean Cisco is recommending using 12.2.(25) for 802.1x for these switches eventhough 12.1(19) supports it?
Thanks
RaviOnly the following 3560 are supported in 12.1.19EA1:
Catalyst 3560-24PS
Catalyst 3560-48PS
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat3560/12119ea1/ol510401.htm#84866
The rest of 3560 have different minimum IOS requirements:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat3750/125see1/ol9586.htm#wp84866
So, wht I am trying to say is, the feature, 802.1x-Vlan Assignment is supported in 12.1(19)EA1 but depending on what kind of 3560, it will require a minimum IOS. If your 3560 is either Catalyst 3560-24PS or Catalyst 3560-48PS, you can run 802.1x-Vlan Assignment on it.
Please rate all posts. -
Network ready for Cisco wireless ?
I know for IPT their is lots of network readiness guides. Is their anything like that for Cisco wireless (with central controler)? We looking at putting in Dell swithcs and not cisco. Anybody have any switch level feture I should be looking out for?
For autonomous you would likely need less features on a switch then with autonomous access points. I'm not a fan of Dell switches, but at the edge they should be fine. With the lightweight APs you don't have to trunk to the access points ('cept H-REAP configs), so you could potentially plug them into hubs!
I would probably look for a PoE midspan if you are not using the new 3560E swithes. Microsemi sells a managed hi-power midspan that support all Cisco access points all the way up to the 1250s (and assumptively beyond). Purchasing 802.3af PoE now seems like a bad idea. -
Meraki vs Cisco Wireless Solutions
Can anybody out there share any information on company called Meraki? We currently have a Cisco wireless solution but our administration has suddenly been looking into Meraki as a replacement. Any info would be greatly appreciated.
Thanks...I actually have both product sets running- our main campus network has over 3,000 APs (Cisco) and we have a 6-month old Meraki installation on our London campus with 35 MR16 APs. While our lightwieght Cisco deployment has been mostly fine on the client-facing side of life, we have had a lot of angst with controllers (we've been in the game since 2006 on LWAPP/CAPWAP, with hundreds of Aeronet fat APs prior) and various code versions through the years. I also follow the industry pretty closely as an IT writer, and so have watched the likes of Aerohive get more interesting (also controllerless) and architectures like Motorola's WiNG 5 greatly de-emphasize the controller. Personally, I've become a lot more open-minded about the cloud and cynical about the expense and grief of controllers. But it's far from black and white- there is no "this is clearly better than that", especially when you've got a wild mix of client devices that just want the network to work and could care less whose label is on the AP.
Bake-offs have validity, but more so (to me) on the "how easy is it to administer" perspective than "will it work for clients?" front. Both our Meraki and Cisco environments nicely serve our clients in dense environments- if they didn't, they wouldn't stay in business. The interference detection and reporting is somewhat overmarketed (again, my opinion) as often interference sources are fleeting and you can't possibly react to every one. Meraki has provided a lot of for things like rate limiting, firewalling, a great guest portal (I can't speak favorably of Cisco's guest portal at all, and BlueSocket has the absolute best I've seen yet) that our Cisco controllers don't do without help from outside boxes- but if you already have those boxes you may not care. I do take Cisco to task on really clunky debug in the CAPWAP world, and there are often gaps between what you can do with WCS/NCS and what you have to do on the controllers directly. The point? Again, it's just not black and white.
For me, I would certainly go with Meraki again for deployments up to a certain size- like a few hundred APs- as one who is living the Meraki life currently and cringes at the price controllers fetch. It does flawless with 802.1x and has a pretty robust feature set in it (not sure why someone above is saying it doesn't)- if you need it. I've had zero problems since putting Meraki in where as I can't wait to get rid of my WiSMs in favor of 5508s (but really wish cisco would provide a VM-based controller like Bluesocket does), but both products have warts at times on the UI. Things I've griped about Meraki was quick to address or put on the short road map, Cisco not so much but eventually they resond to enough grousing. (Yes- my opinion only)
Enough rambling- I'd say visit customers that have both, and don't discount either until you do. Cisco has market share, Meraki is part of the interesting new guard that dares to do things differently. They both work, but you have to find what's right for you. -
Dear Expert,
I want to give solution to one of my cutomers. But I am new to cisco wireless. I am listing products below. Will this fulfill requirement
I have one more doubt, can I able to upgrade AIR-AP1262N-N-K9 to LWAP and can be able to connect this AP to WLC (AIR-WLC4402-12-K9)?
It is urgent Kindly suggest.
AIR-AP1262N-N-K9
802.11a/g/n Standalone AP; Ext Ant; N Reg Domain
AIR-ANT2422DW-R
2.4 GHz 2.2 dBi Swivel Dipole Antenna White, RP-TNC
AIR-ANT5135DW-R
5 GHz 3.5 dBi Swivel Dipole Antenna White, RP-TNC
AIR-AP-BRACKET-2
1040/1140/1260/3500 Universal Mounting Bracket
AIR-AP-T-RAIL-R
Ceiling Grid Clip for Aironet APs - Recessed Mount (Default)
S126W7K9-12425JA
Cisco 1260 Series IOS WIRELESS LAN
CON-SNT-AP1262N
SMARTNET 8X5XNBD 802.11a/g/n Standalone AP; Ext Ant
Product Code
Description
AIR-WLC4402-12-K9
4400 Series WLAN Controller for up to 12 Lightweight APs
AIR-PWR-CORD-AP
AIR Line Cord Asia Pacific (APAC)
SWLC4400K9-60
Cisco Unified WLAN Controller SW Release 6.0 - MD
SWLC4400K9-60-ER
WLAN Controller Emergency SW for 4400 - ED
CON-SNT-WC440212
SMARTNET 8X5XNBD 4402-12 WLAN Controller
Product Code
Description
POE-180X=
802.3af PoE Module, 80W Power Supply and Cable
CAB-AC2E
AC Power cord Europe
GLC-SX-MM-RGD=
1000Mbps Multi-Mode Rugged SFPI have one more doubt, can I able to upgrade AIR-AP1262N-N-K9 to LWAP and can be able to connect this AP to WLC (AIR-WLC4402-12-K9)?
WLC 4400 is end-of-sale since December 2010. Your only choice is the WLC 5508 with corresponding license. Your software should be 7.0.98.0 or newer.
CON-SNT-AP1262N
Cisco Lifetime Warranty
POE-180X=
What is this for???
GLC-SX-MM-RGD=Again, what is this for??? What switch are you plugging this into? -
No of SSID support on Cisco WLC
Hi All,
Can you please help me on providing below details on Cisco wireless controller?
1. No of SSID support on Cisco WLC
2. Is it possible to restrict SSID on AP's (e.g. I have 10 SSID's configured on controller, I want first 10 Access points use set of SSID (SSID 1-5), and rest of the AP use SSID 6-10.
Thanks
JamalHi Jamal,
Just to add a touch to the great info from Robert (+5 points Robert)
The feature you are looking for is called WLAN Override in WLC 4.x versions.
Enabling WLAN Override
By default, access points transmit all defined WLANs on the controller. However, you can use the WLAN Override option to select which WLANs are transmitted and which ones are not on a per access point basis. For example, you can use WLAN override to control where in the network the guest WLAN is transmitted or you can use it to disable a specific WLAN in a certain area of the network.
From this doc;
http://www.cisco.com/en/US/docs/wireless/controller/4.0/configuration/guide/c40wlan.html#wp1114777
Once you create a new WLAN, the WLAN > Edit page for the new WLAN appears. In this page you can define various parameters specific to this WLAN including General Policies, RADIUS Servers, Security Policies, and 802.1x Parameters.
**Check Admin Status under General Policies to enable the WLAN. If you want the AP to broadcast the SSID in its beacon frames, check Broadcast SSID.
Note: You can configure up to sixteen WLANs on the controller. The Cisco WLAN Solution can control up to sixteen WLANs for Lightweight APs. Each WLAN has a separate WLAN ID (1 through 16), a separate WLAN SSID (WLAN name), and can be assigned unique security policies. Lightweight APs broadcast all active Cisco WLAN Solution WLAN SSIDs and enforce the policies that you define for each WLAN.
From this good doc;
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a0080665d18.shtml#c3
In 5.x versions you will use AP Groups, because in WLC 5.x versions, WLAN Override has been replaced with the "AP Groups" feature;
Creating Access Point Groups
After all access points have joined the controller, you can create up to 150 access point groups and assign up to 16 WLANs to each group. Each access point advertises only the enabled WLANs that belong to its access point group. The access point does not advertise disabled WLANs in its access point group or WLANs that belong to another group.
http://www.cisco.com/en/US/docs/wireless/controller/5.2/configuration/guide/c52wlan.html#wp1128591
To learn more about AP Groups check out George's excellent video
http://www.my80211.com/cisco-labs/2009/3/22/cisco-ap-group-nugget.html
Hope this helps!
Rob
Maybe you are looking for
-
How can i change my credit card information in itunes?
My credit card has expired and when I tried to enter a new one in my Itunes account it won't allow me! I've also tried to select Paypal and even though it says in Paypal that Ive created the account with Itunes... it doesn't seem to work in Itunes. C
-
My iPod touch (3rd gen - 64 gig) keeps advising me that my Apple ID has been disabled - it doesn't say for security reasons I have reset the device, changed my password twice, and left it overnight but it still will not allow me to update OR install
-
HT202118 new apple TV - how to restore without micro cable
Hi everyone - and Merry Christmas I've bought an Apple TV and it worked fine this morning, and now it doesn't work and keeps putting up a picture of connecting to iTunes. From what I've read I have to have a micro cable??? I don't have one of these.
-
Travel Management & Funds Management integration
Hello Experts, During creation of a travel request & when I am entering amount in "Estimated Costs" field, I am getting an error message as "Error creating commitment: Trip status has been set to 'open'. Message no. PTRA_WEB_INTERFACE098". This is du
-
My apple won't do the app updates
i've about had it with this computer i was prompted earlier today to do a app updates. i delayed it for a hour, then went back to do it and it says "there was a error in the app store. ( 20 ) what do i do,,,