802.1x between Switch 3750 and ACS 4.2 Authentication faild --need help

I configured the Switch 3750 and ACS for 802.1x authentication.
when I used the windows as the 802.1x client, it prompted "click here to enter user name and pasword for the network " as normal.
The problem is that after I entered username and password (i am sure i enter the identical username and password as in ACS) the authentication failed,
What is the most possibly problem?
Thx in advance!!!
The configuration is Sw3750 is:
aaa new-model
aaa authentication login default local
aaa authentication enable default line
aaa authentication dot1x default group radius
aaa authorization network default group radius
dot1x system-auth-control
interface GigabitEthernet1/0/18
description Link to test 802.1x
switchport access vlan 119
switchport mode access
dot1x pae authenticator
dot1x port-control auto
spanning-tree portfast
radius-server host 10.1.1.333 auth-port 1645 acct-port 1646
radius-server source-ports 1645-1646
radius-server key keepopen0
In the ACS:
Network Configuration -->aaa client ip address: 10.1.119.1(the vlan 119's ip address), shared secret: keepopen0
user setup -->real name:test1, password: test1.
Attached is the debug information

What do you see in acs failed attempts?

Similar Messages

Difference between Switch -off and disable of an aggregate.

Hi All,
Can any one please tell me whats the difference between Switch-off and Disable an aggregate?
Appreciate ur help.
Thanks,
Soumya.

Hi,
You can temporarily switch off an aggregate to check if you need to use it. An aggregate that is switched off is not used when a query is executed.
To do this select the relevant aggregate and choose This graphic is explained in the accompanying text Switch On/Off. An aggregate that is switched off is marked in column Filled/Switched off with This graphic is explained in the accompanying text.
Since aggregates that are switched off must also be consistent, you do not have to activate the aggregate again or to fill it when you switch it back on.
Execute a query or trace that would use the aggregate that was switched off. Compare the time that the database needs with the time that the query needs when using the aggregate. If the query is not significantly slower without the aggregate, you can deactivate or delete the aggregate.
The system deletes all the data and database tables of an aggregate. The definition of the aggregate is not deleted.
Deactivation
Select the required aggregate and choose This graphic is explained in the accompanying text Deactivate.
The status display in the columns Status and Filled/switched off change back to This graphic is explained in the accompanying text.
If you want to, you can activate and fill the aggregate again later.
More information:
http://help.sap.com/saphelp_nw70ehp1/helpdata/en/26/4bc0417951d117e10000000a155106/frameset.htm
Hope it helps.
Regards,
Ray

Re: Difference between switcher component and router activity

Hi all,
Here i want to know the difference between switcher component and router activity.
Can anybody give the difference between them or suggest any blog for this.
Thanks,
Syam

<af:switcher> component is an ADF Faces component. You can use it within (the source of) a JSF page or fragment to include a particular group of other JSF components depending on the switcher expression's value.
Router activity is not a JSF component, i.e. you cannot use it within a JSF page of fragment. It is an ADF taskflow activity. You can use it as an activity within an ADF Taskflow to route transitions between some other activities in the taskflow depending on the router's expression.
Dimitar

Nokia E71 Difference between Switch mode and Profi...

I have Nokia E71, Phone having option to switch modes and also we have profile option.
Can some body explain the difference between switch mode and having different profile ?.
Thanks

The profile impacts things like default ringtone, vibration settings, etc.
With the mode switching you can also switch active standby applications and plugins (e.g., work vs. free time).
Personally, I don't use the modes, and with profiles, I only use "General" and "Silent" and don't bother with others.

IDVD is producing DVDs which chop the edges off my video. I have tried changing the aspect ratio between 4:3 and 16:9 but it hasn't helped. My TV is definitely on the correct settings. How can I solve this?

iDVD is producing DVDs which chop the edges off my video. I have tried changing the aspect ratio between 4:3 and 16:9 but it hasn't helped. My TV is definitely on the correct settings. How can I solve this?

One way to to put the videos into an iDVD slideshow
and set iDVD's Slideshow preferences to always scale slides to TV Safe Area.
However, some users have reported that the audio quality using this method is lessened. I've not noticed it but then I don't have a good ear when it comes to that sort of thing. If you add more than one video in the same slideshow do not select any transition.
OT

My screen is completely white, i've tried holding lock and home buttons as seen on you tube something called 'white screen of death' its goes black (think it switches off) then back to the white screen need help fast please!

my screen is completely white, i've tried holding lock and home buttons as seen on you tube something called 'white screen of death' its goes black (think it switches off) then back to the white screen need help fast please!

If you have not done a factory reset on the device, I recommend doing a complete factory reset.
Factory Reset - Warning this will reset device back to original factory settings.
This method will not erase any MDN/MIN information
Turn off the phone
Press Power + Volume Up/Down at the same time and hold until display will show a triage android screen
Display will show:
Reboot system Now
Apply sdcard:update.zip
Wipe Data/Factory Reset
Wipe Cache Partition
Use VOL Down key to scroll down to "Wipe Data/Factory Reset", press home icon to select option and wipe device.
Display shows "All user data will be wiped out", press VOLUME Up to continue or VOLUME Down to exit.
Press Volume Up
Press Home to select "Reset System Now" - device will reboot
If the problem persist I recommend having a store technician take a look at the device.
Copy and paste the link below into your browser's address bar for the store locator.
http://www.verizonwireless.com/b2c/storelocator/index.jsp

Hi i jus hit the restore all button in my settings and my phone is getting a display signal of switching off and it lies in dat mode plz help me out

hi i jus hit the restore all button in my settings and my phone is getting a display signal of switching off and it lies in dat mode plz help me out

You need to perform a DFU Mode Restore of the iPhone with iTunes on computer. You must also have a SIM card of the original Carrier that this iPhone was produced for.

I can't connect to wifi network and bluetooth on iPhone 4S. Need help. Have already rebooted everything and reset network setting

I can't connect to wifi network and bluetooth on iPhone 4S. Need help. Have already rebooted everything and reset network setting

I have the same problem; tried a phone restore, both restoring data and setting up as new phone with factory settings, reset all settings, re-boot, remove apostrophe, put in fridge, you name it!
I think there's quite a few iphone 4s users with the same problem!
I called Apple they said it's a hardware problem, but it has worked for nearly two years; they say go to the Apple store and they can provide a replacement phone for approx. £150!
I've been into the O2 shop where I bought it and they knew the problem exactly; said they had sent a few phones off for repair and had them back awith a report they cannot fix it because it's a software problem!
An assistant in the shop had the same issues; logic says it's a software problem and hopefully Apple will fix it with a patch but at the moment they seem to be avoiding everyones comments!
If anyone else has any ideas these would be appreciated?

Why i cannot update my new apple tv 3g and i cannot watch you yube need help

why i cannot update my new apple tv 3g and i cannot watch you yube, need help.

If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
Connect the micro USB cable to the Apple TV and to your computer.
Reconnect the power cable (only for Apple TV 3)
Open iTunes.
Select your Apple TV in the Devices list, and then click Restore.

HT1937 I have an iphone bought in the UK but I'm in Europe and can not use it I need help please help me thanks

I have an iphone bought in the UK but I'm in Europe and can not use it I need help please help me thanks

wiliiam rrichard wrote:
Because My iphone is Locked on the United Kingdom
No it is not. iPhones, like all cell phones are not locked to countries. They are locked to carriers.
Only the carrier to whom the device is locked can unlock it. Contact the carrier.

HT201210 i can't restore my iphone4 from 5.1 to 6 and it stuck in recovery mode need help

i can't restore my iphone4 from IOS 5.12 to IOS 6 and it stuck in recovery mode need help please

Read here > http://support.apple.com/kb/HT1808
Hope that helps.

Etherchannel between stack switches[3750] and standalone switch[3560]

Hi,
I have 2*3750 switches in stack as core and 1*3560 switch in access layer. I want to enable ether channel between stack switch[3750A & 3750B] and 3560 switches.
Have connected 2 links from 3560 switch to stack switch, one link to 3750A and other link to 3750B. Will it work in this way as per my requirement?
or i should enabled stacking on 3560 switch too and configure cross-stack ether channel between 3750 stack and 3560 stack. i refered few cisco documents, but the cross stack etherchannel configuration example has 3750 at both end stacks.
Rgds...
VikramS

Hi,
This should work fine as per you set up, the 3750 stack will be acting as one switch, which means that the ether-channel configuration should be straight forward. There is no need to stack the 3560 for this to work, also the 3560 are not stackable.
Hope this helps.

802.1q between CAT 6500 and Passport 8600

Hi,
I`m configuring 802.1q trunking between CAT 6500 and passport 8600, in CAT 6500 I configure the port as trunk dot1q mode ON. In Passport 8600 I configure the port as TAG port.
I cretate the same vlans in both switch, but the interface vlans are create in CAT Switch. all hosts in Passport Switch that belongs to vlan 1 can ping his default gateaway (Interface Vlan) but hosts that belong to other vlan no.

Please somebody helpme

Difference between switch logfile and checkpoint

Hi All,
what is the difference between
Forcing log file switches:
ALTER SYSTEM switch logfile;
and
ALTER SYSTEM checkpoint;
when i should use one and not use the other
Thanks very much

I don't know that checkpoint will increase the scn. In a way it can be called correct but there are multitudes of SCN floating around. For example, for the matching of the datafiles and controlfles, there are two scn's which are used, stop scn and checkpoint scn. Than for the block, there can be , commit scn , transaction scn , High scn and low scn. There is one counter that is there for both checkpoint and SCN and checkpoint number is generated from SCN itself. I am sure that there is a missing link here some where but still, to some extent this is correct.
Checkpointing is an event which happens at certain conditions and SCN is always there, just like in a clock, there is always a time.
HTH
Aman....

Can I use home sharing between my iPhone and iPad? Or do I need to use a computer?

I want to use home sharing between my iPhone and Ipad. So I can use the remote app. But I can't get it to work

You can use it to share the library on your computer to the iPad, not the other way around.
On the computer, set up homesharing in the advanced menu. On the iPad go to settings > music.

802.1x between Switch 3750 and ACS 4.2 Authentication faild --need help

Similar Messages

Maybe you are looking for