802.1x Cisco ISE & Cathalyst
Hi
I’ve got a curious problem with the authentication of not correct authenticated 802.1x-clients. In the ISE I have select that every failed authentication should be rejected. But the authentication process starts again and again and does not stop. Here the log from the switch:
May 30 14:10:27.608 METDST: %AUTHMGR-5-START: Starting 'dot1x' for client (0c0c.0c0c.0c01) on Interface Fa0/1
May 30 14:10:27.893 METDST: %DOT1X-5-FAIL: Authentication failed for client (0c0c.0c0c.0c01) on Interface Fa0/1
May 30 14:10:27.893 METDST: %AUTHMGR-7-RESULT: Authentication result 'fail' from 'dot1x' for client (0c0c.0c0c.0c01) on Interface 0/1
May 30 14:10:28.270 METDST: %AUTHMGR-5-START: Starting 'dot1x' for client (0c0c.0c0c.0c01) on Interface Fa0/1
May 30 14:10:28.404 METDST: %DOT1X-5-FAIL: Authentication failed for client (0c0c.0c0c.0c01) on Interface Fa0/1
May 30 14:10:28.404 METDST: %AUTHMGR-7-RESULT: Authentication result 'fail' from 'dot1x' for client (0c0c.0c0c.0c01) on Interface
May 30 14:10:29.118 METDST: %AUTHMGR-5-START: Starting 'dot1x' for client (0c0c.0c0c.0c01) on Interface Fa0/1
May 30 14:10:29.361 METDST: %DOT1X-5-FAIL: Authentication failed for client (0c0c.0c0c.0c01) on Interface Fa0/1
May 30 14:10:29.361 METDST: %AUTHMGR-7-RESULT: Authentication result 'fail' from 'dot1x' for client (0c0c.0c0c.0c01) on Interface Fa0/1
May 30 14:10:29.420 METDST: %AUTHMGR-5-START: Starting 'dot1x' for client (0c0c.0c0c.0c01) on Interface Fa0/1
May 30 14:10:29.839 METDST: %DOT1X-5-FAIL: Authentication failed for client (0c0c.0c0c.0c01) on Interface Fa0/1
May 30 14:10:29.839 METDST: %AUTHMGR-7-RESULT: Authentication result 'fail' from 'dot1x' for client (0c0c.0c0c.0c01) on Interface Fa0/1
May 30 14:10:30.745 METDST: %AUTHMGR-5-START: Starting 'dot1x' for client (0c0c.0c0c.0c01) on Interface Fa0/1
May 30 14:10:30.846 METDST: %DOT1X-5-FAIL: Authentication failed for client (0c0c.0c0c.0c01) on Interface Fa0/1
May 30 14:10:30.846 METDST: %AUTHMGR-7-RESULT: Authentication result 'fail' from 'dot1x' for client (0c0c.0c0c.0c01) on Interface Fa0/1
May 30 14:10:31.794 METDST: %AUTHMGR-5-START: Starting 'dot1x' for client (0c0c.0c0c.0c01) on Interface Fa0/1
May 30 14:10:31.928 METDST: %DOT1X-5-FAIL: Authentication failed for client (0c0c.0c0c.0c01) on Interface Fa0/1
May 30 14:10:31.928 METDST: %AUTHMGR-7-RESULT: Authentication result 'fail' from 'dot1x' for client (0c0c.0c0c.0c01) on Interface Fa0/1
I configured that only one authentication is allowed. If the authentication failed, the port should be blocked. But that does not happen.
A successful authenticated client always triggers two authentications. That is also curious.
Has anybody an idea to solve this behavior?
Many thanks Marco
Here the port config:
interface FastEthernet0/1
switchport mode access
switchport voice vlan 3
authentication host-mode multi-domain
authentication order dot1x mab
authentication priority dot1x mab
authentication port-control auto
authentication violation protect
mab
dot1x pae authenticator
dot1x timeout tx-period 3
dot1x max-reauth-req 1
spanning-tree portfast
spanning-tree bpduguard enable
spanning-tree guard root
@ RikJonAtk: dot1x timeout quit-period is 60 sec standard. I do not want that the client can authenticate again.
@ Jatin Katyal: Where can I find the status of CoA?
Similar Messages
-
Cisco ip phones authenticate 802.1x with cisco ise 1.3
Dear all,
I want to configure cisco ise 1.3 with 802.1x , to authenticate cisco ip phones ( CUCM 10.5.2 ) with LSC certificate.
How I have to configure cisco ise authentication rules for 802.1x with cisco ip phones? Are there any configuration examples ?
Thanksfollowing are ISE 802.1x sample authentication rules..you can change the protocol (Policy -> policy elements - > results -> authentication and you can select the proctocal)
-
Cisco ISE FlexAuth with 802.1X PCs and IP Phones as MAB multi-domain Q?
Cisco ISE FlexAuth with 802.1X PCs and IP Phones as MAB multi-domain Q?
Im trying to follow the trustsec 2.1 guide on IP Phones into LowImpact mode.
I can get a PC on its own to authenticate via dot1x/tls
I can get a Cisco IP Phone on its own to authenticate via MAB.
When the two are on the same switchport, the phone will authenticate but not the PC. ISE logs EAP timeouts.
The switchport has the LowImpact port ACL of
ip access-group ACL-DEFAULT in
The IP Phone gets a dACL that allows it ok.
I assume MAB phone and dot1x PC is supported? Any ideas?
Thanks in advance.The ISE log detailed steps are as follows:
Steps
11001 Received RADIUS Access-Request
11017 RADIUS created a new session
Evaluating Service Selection Policy
15048 Queried PIP
15048 Queried PIP
15004 Matched rule
11507 Extracted EAP-Response/Identity
12300 Prepared EAP-Request proposing PEAP with challenge
12625 Valid EAP-Key-Name attribute received
11006 Returned RADIUS Access-Challenge
11001 Received RADIUS Access-Request
11018 RADIUS is re-using an existing session
12501 Extracted EAP-Response/NAK requesting to use EAP-TLS instead
12500 Prepared EAP-Request proposing EAP-TLS with challenge
12625 Valid EAP-Key-Name attribute received
11006 Returned RADIUS Access-Challenge
11001 Received RADIUS Access-Request
11018 RADIUS is re-using an existing session
12502 Extracted EAP-Response containing EAP-TLS challenge-response and accepting EAP-TLS as negotiated
12800 Extracted first TLS record; TLS handshake started
12805 Extracted TLS ClientHello message
12806 Prepared TLS ServerHello message
12807 Prepared TLS Certificate message
12809 Prepared TLS CertificateRequest message
12505 Prepared EAP-Request with another EAP-TLS challenge
11006 Returned RADIUS Access-Challenge
11001 Received RADIUS Access-Request
11018 RADIUS is re-using an existing session
12504 Extracted EAP-Response containing EAP-TLS challenge-response
12505 Prepared EAP-Request with another EAP-TLS challenge
11006 Returned RADIUS Access-Challenge
11001 Received RADIUS Access-Request
11018 RADIUS is re-using an existing session
12504 Extracted EAP-Response containing EAP-TLS challenge-response
12505 Prepared EAP-Request with another EAP-TLS challenge
11006 Returned RADIUS Access-Challenge
5411 No response received during 120 seconds on last EAP message sent to the client -
Cisco ISE for 802.1x (EAP-TLS)
I work for a banking organization and security is an area that needs to be improved continuously. I am planning on implementing Cisco ISE for 802.1x together with a Microsoft PKI for certificate issuing and signing.
I am currently trying to implement this in our test environment and I have managed to do a few basic bootstrapping tasks. I need someone to push me into the right direction as to how I can achieve what i am seeking.
I will use Cisco 2900 series switches on the access layer and a few HP switches as well which supports 802.1x.
I want to configure the ISE to process authentication requests using 802.1x EAP-TLS (Certificate Based). All the workstations on the domain needs to authenticate itself using the certificates issued to it by the Certificate Issuing Authority.
I have already managed to get the PKI working and have rolled out the certificates on all the workstations on the test environment. I can't seem to configure the Authentication portion on the ISE.
I request if someone can guide me or direct me to materials that can help achieve the above requirements. The guides available on the Cisco website are overwhelming and I can't seem to figure out how I am supposed to configure the authentication portion.
My email: [email protected]
Cheers,
Krishil ReddyHello Mubashir,
Many timers can be modified as needed in a deployment. Unless you are experiencing a specific problem where adjusting the timer may correct unwanted behavior, it is recommended to leave all timers at their default values except for the 802.1X transmit timer (tx-period).
The tx-period timer defaults to a value of 30 seconds. Leaving this value at 30 seconds provides a default wait of 90 seconds (3 x tx-period) before a switchport will begin the next method of authentication, and begin the MAB process for non-authenticating devices.
Based on numerous deployments, the best-practice recommendation is to set the tx-period value to 10 seconds to provide the optimal time for MAB devices. Setting the value below 10 seconds may result in the port moving to MAC authentication bypass too quickly.
Configure the tx-period timer.
C3750X(config-if-range)#dot1x timeout tx-period 10 -
Cisco ip phones authenticate 802.1x with cisco ise
Dears,
I want to configure ip phones authenticate from Cisco ISE with 802.1X with certificates. But i can not find any configuration guide about this solutions.
I find one config and this is about ACS. Please provide me any documentation guide on cisco ise.
Thanks.802.1x configuration for IP Phones
http://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/Security/TrustSec_1-99/IP_Tele/IP_Telephony_DIG.html#69217 -
Cisco ISE and authentication for 802.1x printer
Hello
What is the best practice to authenticate a 802.1x printer in Cisco ISE?
The printer can store a certificate for authentication and support EAP-TLS.
Thanks for answer.
MarcoEAP-TLS is the way to go. It is way way way more secure than MAB and profiling. However, the question is "How much of a hassle is it going to be to put a certificate on each printer?" Moreover, "What methods do I have (if any) to renew those certificates when they expire?" If have to manually generate a CSR and install a cert on each printer then it can quickly become an administrative overhead nightmare. With that being said, you can use MAB and profiling but just make sure that you lock down the access that those printers get. For instance, do they need access to the internet? Do they need access to anything else but the print server and/or open to all IPs access but only on the printing ports.
I hope this puts you in the right direction!
Thank you for rating helpful posts! -
Cisco ISE: 802.1x [EAP-TLS] + List of Applicable Hot-Fixes
Dear Folks,
Kindly suggest the list of all possible Hot-Fixes required for the Cisco ISE EAP-TLS solution... We have applied 9 HotFixes so far. But, still the connectivity is intermittent. Is there any list for all applicable Hot-Fixes?
OS = Win 7 SP1 (32/64 Bit) and Win 8
Thanks,
Regards,
Mubasher SultanHi Mubasher
KB2481614: If you’re configuring your 802.1x settings via Group Policy you’ll see sometimes EAP-PEAP request from clients in your radius server log during booting even if you’ll set EAP-TLS. This error happened in our case with 1/3 of the boots with some models. The error is caused by a timing problem during startup. Sometimes the 802.1x is faster and sometimes the Group Policy is, and if the 802.1x is faster than the default configuration is taken, which is PEAP. Which lead to a EAP-NAK by the radius server.
KB980295: If an initial 802.1x authentication is passed, but a re-authentication fails, Windows 7 will ignore all later 802.1x requests. This hotfix should also fix a problem with computers waking up from sleep or hibernation – but we’ve disabled these features so I can’t comment on them.
KB976373: This hotfix is called “A computer that is connected to an IEEE 802.1x-authenticated network via another 802.1x enabled device does not connect to the correct network”. I can’t comment on this, as we’ve not deployed 802.1x for our VoIP phones at this point.I would guess it is the same for Windows 7 too. The linked article tells you to install the patch and set some registry key to lower the value.
KB2769121: A short time ago I found this one: “802.1X authentication fails on a Windows 7-based or Windows 2008 R2-based computer that has multiple certificates”. At time of writing I’m not sure if it helps for something in my setup. According to the symptoms list of the hotfix, it does not, but maybe it helps for something else, as the one before does.
KB2736878: An other error during booting – this time it happens if the read process starts before the network adapter is initialized. Really seems that they wanted to get faster boot times, no matter the costs.
KB2494172: This hotfix fixes a problem if you’ve installed a valid and invalid certificate for 802.1x authentication. The workaround is just deleting the invalid certificate. I’m not sure at this point if it affects also wired authentication.
KB976210:This problem occurs only during automated build processes and if you use an EAP method which needs user interaction – as I don’t do that I can’t comment on this hotfix.
For more information please go through this link:
http://robert.penz.name/555/list-of-ieee-802-1x-hotfixes-for-windows-7/
Best Regards:
Muhammad Munir -
Configuration Cisco switch 802.1x for ISE
Hi dears,
I configurated EAP_FAST authentication on Cisco ISE from Cisco Video material. Now I need full 802.1X configuration in cisco switch guide or video link.
Please provide this.
Thanks.See this link:
http://www.cisco.com/c/en/us/td/docs/security/ise/1-2/user_guide/ise_user_guide/ise_sw_cnfg.html -
Cisco ISE 1.2 & Cisco WLC 5508 v7.6
Hi all,
we are planning to upgrade our WLC to 7.6 to fix a bug with FlexConnect Client ACLs but I have just seen on the Cisco ISE Compatibility table that the it only recommends up to v7.5 of the WLC 5508...
Cisco have told me to steer clear of 7.5 as it is in a defferred status, so does anyone know, or have running in a lab or production, ISE1.2 with a 5508 WLC v7.6 NAD ?
I would much rather know of any issues people are experiencing before hand than to have to go through a software upgrade and then rollback.
Thanks all
Mario De RosaHi Neno,
right I have this almost working now.
I have simplified the setup. I am not going to do any client provisioning at the moment.
So I can connect to the corporate SSID using EAP-TLS and I can successfully push the branch data VLAN upon successful authorisation.
Now I am trying to introduce the posture element & per user ACLs.
I have defined the redirect ACL & Flex ACL on the vWLC however the NAC agent will not pop-up. The client is in the right VLAN and the redirect ACL seems to be getting applied as the client does get an IP through DHCP. However, the client cannot ping the ISE or access the guest portal when I open the browser.
DNS resolution seems to be working fine.
VLAN220 is my datacentre VLAN which the Management Interface on the controller is plugged in to.
VLAN10 is the branch DATA VLAN.
below is some output to give you some more details...
(Cisco Controller) >show client detail 00:24:d6:97:b3:be
Client MAC Address............................... 00:24:d6:97:b3:be
Client Username ................................. [email protected]
AP MAC Address................................... 18:33:9d:f0:21:80
AP Name.......................................... test-flex-ap
AP radio slot Id................................. 0
Client State..................................... Associated
Client NAC OOB State............................. Access
Wireless LAN Id.................................. 2
Hotspot (802.11u)................................ Not Supported
BSSID............................................ 18:33:9d:f0:21:81
Connected For ................................... 128 secs
Channel.......................................... 6
IP Address....................................... 10.130.130.120
Gateway Address.................................. 10.130.130.1
Netmask.......................................... 255.255.255.0
IPv6 Address..................................... fe80::f524:1910:69f0:9482
Association Id................................... 1
Authentication Algorithm......................... Open System
Reason Code...................................... 1
Status Code...................................... 0
Client CCX version............................... 4
Client E2E version............................... 1
--More-- or (q)uit
Re-Authentication Timeout........................ 1651
QoS Level........................................ Silver
Avg data Rate.................................... 0
Burst data Rate.................................. 0
Avg Real time data Rate.......................... 0
Burst Real Time data Rate........................ 0
802.1P Priority Tag.............................. disabled
CTS Security Group Tag........................... Not Applicable
KTS CAC Capability............................... No
WMM Support...................................... Enabled
APSD ACs....................................... BK BE VI VO
Power Save....................................... OFF
Current Rate..................................... m13
Supported Rates.................................. 1.0,2.0,5.5,11.0,6.0,9.0,
............................................. 12.0,18.0,24.0,36.0,48.0,
............................................. 54.0
Mobility State................................... Local
Mobility Move Count.............................. 0
Security Policy Completed........................ No
Policy Manager State............................. POSTURE_REQD
Policy Manager Rule Created...................... Yes
AAA Override ACL Name............................ POSTURE_REDIRECT_ACL
AAA Override ACL Applied Status.................. Yes
--More-- or (q)uit
AAA Override Flex ACL Name....................... POSTURE_REDIRECT_ACL
AAA Override Flex ACL Applied Status............. Yes
AAA URL redirect................................. https://pdc-ise-man01.kier.group:8443/guestportal/gateway?sessionId=c8dc800a00000005b3e7e953&action=cpp
Audit Session ID................................. c8dc800a00000005b3e7e953
AAA Role Type.................................... none
Local Policy Applied............................. none
IPv4 ACL Name.................................... none
FlexConnect ACL Applied Status................... Yes
IPv4 ACL Applied Status.......................... Unavailable
IPv6 ACL Name.................................... none
IPv6 ACL Applied Status.......................... Unavailable
Layer2 ACL Name.................................. none
Layer2 ACL Applied Status........................ Unavailable
mDNS Status...................................... Disabled
mDNS Profile Name................................ none
No. of mDNS Services Advertised.................. 0
Policy Type...................................... WPA2
Authentication Key Management.................... 802.1x
Encryption Cipher................................ CCMP (AES)
Protected Management Frame ...................... No
Management Frame Protection...................... No
EAP Type......................................... EAP-TLS
FlexConnect Data Switching....................... Local
--More-- or (q)uit
FlexConnect Dhcp Status.......................... Local
FlexConnect Vlan Based Central Switching......... No
FlexConnect Authentication....................... Central
Quarantine VLAN.................................. 0
Access VLAN...................................... 220
Client Capabilities:
CF Pollable................................ Not implemented
CF Poll Request............................ Not implemented
Short Preamble............................. Implemented
PBCC....................................... Not implemented
Channel Agility............................ Not implemented
Listen Interval............................ 10
Fast BSS Transition........................ Not implemented
Client Wifi Direct Capabilities:
WFD capable................................ No
Manged WFD capable......................... No
Cross Connection Capable................... No
Support Concurrent Operation............... No
Fast BSS Transition Details:
Client Statistics:
Number of Bytes Received................... 33698
Number of Bytes Sent....................... 19397
Total Number of Bytes Sent................. 19397
--More-- or (q)uit
Total Number of Bytes Recv................. 33698
Number of Bytes Sent (last 90s)............ 19397
Number of Bytes Recv (last 90s)............ 33698
Number of Packets Received................. 283
Number of Packets Sent..................... 147
Number of Interim-Update Sent.............. 0
Number of EAP Id Request Msg Timeouts...... 0
Number of EAP Id Request Msg Failures...... 0
Number of EAP Request Msg Timeouts......... 0
Number of EAP Request Msg Failures......... 0
Number of EAP Key Msg Timeouts............. 0
Number of EAP Key Msg Failures............. 0
Number of Data Retries..................... 53
Number of RTS Retries...................... 0
Number of Duplicate Received Packets....... 2
Number of Decrypt Failed Packets........... 0
Number of Mic Failured Packets............. 0
Number of Mic Missing Packets.............. 0
Number of RA Packets Dropped............... 0
Number of Policy Errors.................... 0
Radio Signal Strength Indicator............ -42 dBm
Signal to Noise Ratio...................... 41 dB
Client Rate Limiting Statistics:
--More-- or (q)uit
Number of Data Packets Recieved............ 0
Number of Data Rx Packets Dropped.......... 0
Number of Data Bytes Recieved.............. 0
Number of Data Rx Bytes Dropped............ 0
Number of Realtime Packets Recieved........ 0
Number of Realtime Rx Packets Dropped...... 0
Number of Realtime Bytes Recieved.......... 0
Number of Realtime Rx Bytes Dropped........ 0
Number of Data Packets Sent................ 0
Number of Data Tx Packets Dropped.......... 0
Number of Data Bytes Sent.................. 0
Number of Data Tx Bytes Dropped............ 0
Number of Realtime Packets Sent............ 0
Number of Realtime Tx Packets Dropped...... 0
Number of Realtime Bytes Sent.............. 0
Number of Realtime Tx Bytes Dropped........ 0
Nearby AP Statistics:
test-flex-ap(slot 0)
antenna0: 14 secs ago.................... -51 dBm
antenna1: 14 secs ago.................... -37 dBm
test-flex-ap(slot 1)
antenna0: 14 secs ago.................... -51 dBm
antenna1: 14 secs ago.................... -54 dBm
--More-- or (q)uit
DNS Server details:
DNS server IP ............................. 10.0.17.31
DNS server IP ............................. 10.0.17.43
Assisted Roaming Prediction List details:
Client Dhcp Required: False
Allowed (URL)IP Addresses
(Cisco Controller) >
(Cisco Controller) >show wlan 2
WLAN Identifier.................................. 2
Profile Name..................................... Demo1x
Network Name (SSID).............................. Demo1x
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Enabled
Network Admission Control
Client Profiling Status
Radius Profiling ............................ Disabled
DHCP ....................................... Disabled
HTTP ....................................... Disabled
Local Profiling ............................. Disabled
DHCP ....................................... Disabled
HTTP ....................................... Disabled
Radius-NAC State............................... Enabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
--More-- or (q)uit
Number of Active Clients......................... 1
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
User Idle Timeout................................ Disabled
Sleep Client..................................... disable
Sleep Client Timeout............................. 12 hours
User Idle Threshold.............................. 0 Bytes
NAS-identifier................................... mario-test-flex-vwlc
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
WLAN Layer2 ACL.................................. unconfigured
mDNS Status...................................... Disabled
mDNS Profile Name................................ unconfigured
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
Static IP client tunneling....................... Disabled
Quality of Service............................... Silver
Per-SSID Rate Limits............................. Upstream Downstream
Average Data Rate................................ 0 0
--More-- or (q)uit
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Per-Client Rate Limits........................... Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
--More-- or (q)uit
Radius Servers
Authentication................................ 10.0.16.111 1812
Accounting.................................... 10.131.16.111 1813
Interim Update............................. Disabled
Framed IPv6 Acct AVP ...................... Prefix
Dynamic Interface............................. Disabled
Dynamic Interface Priority.................... wlan
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
FT Support.................................... Disabled
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Disabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Enabled
PSK..................................... Disabled
CCKM.................................... Disabled
--More-- or (q)uit
FT-1X(802.11r).......................... Disabled
FT-PSK(802.11r)......................... Disabled
PMF-1X(802.11w)......................... Disabled
PMF-PSK(802.11w)........................ Disabled
FT Reassociation Timeout................... 20
FT Over-The-DS mode........................ Enabled
GTK Randomization.......................... Disabled
SKC Cache Support.......................... Disabled
CCKM TSF Tolerance......................... 1000
WAPI.......................................... Disabled
Wi-Fi Direct policy configured................ Disabled
EAP-Passthrough............................... Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
FlexConnect Local Switching................... Enabled
flexconnect Central Dhcp Flag................. Disabled
flexconnect nat-pat Flag...................... Disabled
flexconnect Dns Override Flag................. Disabled
flexconnect PPPoE pass-through................ Disabled
--More-- or (q)uit
flexconnect local-switching IP-source-guar.... Disabled
FlexConnect Vlan based Central Switching ..... Disabled
FlexConnect Local Authentication.............. Disabled
FlexConnect Learn IP Address.................. Enabled
Client MFP.................................... Optional
PMF........................................... Disabled
PMF Association Comeback Time................. 1
PMF SA Query RetryTimeout..................... 200
Tkip MIC Countermeasure Hold-down Timer....... 60
Eap-params.................................... Disabled
AVC Visibilty.................................... Disabled
AVC Profile Name................................. None
Flow Monitor Name................................ None
Split Tunnel (Printers).......................... Disabled
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Disabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
KTS based CAC Policy............................. Disabled
Assisted Roaming Prediction Optimization......... Disabled
802.11k Neighbor List............................ Disabled
802.11k Neighbor List Dual Band.................. Disabled
Band Select...................................... Disabled
--More-- or (q)uit
Load Balancing................................... Disabled
Multicast Buffer................................. Disabled
Mobility Anchor List
WLAN ID IP Address Status
802.11u........................................ Disabled
MSAP Services.................................. Disabled
Local Policy
Priority Policy Name
(Cisco Controller) >
when debugging the client during redirect, this is the output and I cannot spot anything wrong here...
(Cisco Controller) >*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Adding mobile on LWAPP AP 18:33:9d:f0:21:80(1)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Association received from mobile on BSSID 18:33:9d:f0:21:8e
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Global 200 Clients are allowed to AP radio
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Max Client Trap Threshold: 0 cur: 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be override for default ap group, marking intgrp NULL
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Re-applying interface policy for client
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be In processSsidIE:4850 setting Central switched to FALSE
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying site-specific Local Bridging override for station 00:24:d6:97:b3:be - vapId 2, site 'default-group', interface 'management'
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying Local Bridging Interface Policy for station 00:24:d6:97:b3:be - vlan 220, interface id 0, interface 'management'
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be STA - rates (8): 140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Processing RSN IE type 48, length 22 for mobile 00:24:d6:97:b3:be
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Received RSN IE with 0 PMKIDs from mobile 00:24:d6:97:b3:be
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 8
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be unsetting PmkIdValidatedByAp
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Updating AID for REAP AP Client 18:33:9d:f0:21:80 - AID ===> 1
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Initializing policy
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Central switch is FALSE
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) DHCP required on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2for this client
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Not Using WMM Compliance code qosCap 00
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2 flex-acl-name:
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfMsAssoStateInc
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:24:d6:97:b3:be on AP 18:33:9d:f0:21:80 from Idle to Associated
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfPemAddUser2:session timeout forstation 00:24:d6:97:b3:be - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Stopping deletion of Mobile Station: (callerId: 48)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Sending Assoc Response to station on BSSID 18:33:9d:f0:21:8e (status 0) ApVapId 2 Slot 1
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfProcessAssocReq (apf_80211.c:8294) Changing state for mobile 00:24:d6:97:b3:be on AP 18:33:9d:f0:21:80 from Associated to Associated
*spamApTask6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Sent 1x initiate message to multi thread task for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be EAP-PARAM Debug - eap-params for Wlan-Id :2 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Station 00:24:d6:97:b3:be setting dot1x reauth timeout = 1800
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Connecting state
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Sending EAP-Request/Identity to mobile 00:24:d6:97:b3:be (EAP Id 1)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Received Identity Response (count=1) from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Resetting reauth count 1 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be EAP State update from Connecting to Authenticating for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Authenticating state
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=214) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be WARNING: updated EAP-Identifier 1 ===> 214 for STA 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 214)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Allocating EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 214, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=215) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 215)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 215, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=216) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 216)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 216, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=217) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 217)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 217, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=218) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 218)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 218, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=219) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 219)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 219, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=220) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 220)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 220, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=221) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 221)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 221, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=222) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 222)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 222, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=223) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 223)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 223, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=224) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 224)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 224, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=225) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 225)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 225, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Processing Access-Accept for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting web IPv4 acl from 255 to 255
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting web IPv4 Flex acl from 65535 to 65535
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Username entry ([email protected]) created for mobile, length = 253
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Username entry ([email protected]) created in mscb for mobile, length = 253
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be override for default ap group, marking intgrp NULL
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 220
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Re-applying interface policy for client
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 1 on mobile
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Inserting AAA Override struct for mobile
MAC: 00:24:d6:97:b3:be, source 4
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting re-auth timeout to 1800 seconds, got from WLAN config.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Station 00:24:d6:97:b3:be setting dot1x reauth timeout = 1800
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Creating a PKC PMKID Cache entry for station 00:24:d6:97:b3:be (RSN 2)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting MSCB PMK Cache Entry 0 for station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 8
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Adding BSSID 18:33:9d:f0:21:8e to PMKID cache at index 0 for station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: New PMKID: (16)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: [0000] 6f d1 ce 84 08 74 41 a5 06 6b 89 02 c9 e9 f8 c8
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Disabling re-auth since PMK lifetime can take care of same.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be unsetting PmkIdValidatedByAp
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Client in Posture Reqd state. PMK cache not updated.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAP-Success to mobile 00:24:d6:97:b3:be (EAP Id 225)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Freeing AAACB from Dot1xCB as AAA auth is done for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be EAPOL Header:
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00000000: 02 03 5f 00 .._.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Found an cache entry for BSSID 18:33:9d:f0:21:8e in PMKID cache at index 0 of station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Found an cache entry for BSSID 18:33:9d:f0:21:8e in PMKID cache at index 0 of station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: [0000] 6f d1 ce 84 08 74 41 a5 06 6b 89 02 c9 e9 f8 c8
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Starting key exchange to mobile 00:24:d6:97:b3:be, data packets will be dropped
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Entering Backend Auth Success state (id=225) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Received Auth Success while in Authenticating state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Authenticated state
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Received EAPOL-Key from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Received EAPOL-key in PTK_START state (message 2) from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be PMK: Sending cache add
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Stopping retransmission timer for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be EAPOL Header:
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00000000: 02 03 5f 00 .._.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Received EAPOL-Key from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Stopping retransmission timer for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Freeing EAP Retransmit Bufer for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be apfMs1xStateInc
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state 8021X_REQD (3)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Central switch is FALSE
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Sending the Central Auth Info
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Central Auth Info Allocated PMKLen = 32
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: EapolReplayCounter: 00 00 00 00 00 00 00 01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: EapolReplayCounter: 00 00 00 00 00 00 00 01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be PMK: pmkActiveIndex = 0
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be EapolReplayCounter: 00 00 00 00 00 00 00 01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
apfMsEntryType = 0 apfMsEapType = 13
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) DHCP required on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2for this client
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Not Using WMM Compliance code qosCap 00
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2 flex-acl-name:POSTURE_REDIRECT_ACL
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 6166, Adding TMP rule
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Adding Fast Path rule
type = Airespace AP - Learn IP address
on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
IPv4 ACL ID = 255, IPv
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206 Local Bridging Vlan = 220, Local Bridging intf id = 0
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 5761, Adding TMP rule
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Replacing Fast Path rule
type = Airespace AP - Learn IP address
on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
IPv4 ACL ID = 255,
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206 Local Bridging Vlan = 220, Local Bridging intf id = 0
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*pemReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
*pemReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
*spamApTask6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be spamEncodeCentralAuthInoMsPayload: msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
apfMsEntryType = 0 pmkLen = 32
*DHCP Socket Task: Aug 12 10:58:24.546: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 325,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 10:58:24.546: 00:24:d6:97:b3:be DHCP setting server from ACK (server 10.0.17.85, yiaddr 10.130.130.120)
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 DHCP_REQD (7) Change state to WEBAUTH_REQD (8) last state DHCP_REQD (7)
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) pemAdvanceState2 6671, Adding TMP rule
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Replacing Fast Path rule
type = Airespace AP Client - ACL passthru
on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
IPv4 A
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206 Local Bridging Vlan = 220, Local Bridging intf id = 0
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Successfully plumbed mobile rule (IPv4 ACL ID 1, IPv6 ACL ID 255, L2 ACL ID 255)
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be Plumbing web-auth redirect rule due to user logout
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be Assigning Address 10.130.130.120 to mobile
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be DHCP success event for client. Clearing dhcp failure count for interface management.
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be DHCP success event for client. Clearing dhcp failure count for interface management.
*pemReceiveTask: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 Added NPU entry of type 2, dtlFlags 0x0
*IPv6_Msg_Task: Aug 12 10:58:25.330: 00:24:d6:97:b3:be Pushing IPv6 Vlan Intf ID 0: fe80:0000:0000:0000:f524:1910:69f0:9482 , and MAC: 00:24:D6:97:B3:BE , Binding to Data Plane. SUCCESS !! dhcpv6bitmap 0
*IPv6_Msg_Task: Aug 12 10:58:25.330: 00:24:d6:97:b3:be Link Local address fe80::f524:1910:69f0:9482 updated to mscb. Not Advancing pem state.Current state: mscb in apfMsMmInitial mobility state and client state APF_MS_STATE_A
*DHCP Socket Task: Aug 12 10:58:28.581: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 10:58:28.589: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 11:00:07.959: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 11:00:07.967: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 11:01:59.153: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
Can you see any obvious reason why the NAC agent wont pop up?
Thanks
Mario -
Cisco ISE - Reauthentication of client if server becomes alive again
Dears,
I have this case where Cisco ISE server is used to authenticate & authorize clients on the network.
I configured the switch port to authorize the client in case the ISE server is dead (or not reachable).
The thing is that I want to reauthenticate the client once the ISE server becomes alive again but I am not able to.. ("Additional Information is needed to connect to this network" bullet is not appearing and the client PC remains authenticated and assigned to the VLAN.
Below is the switch port configuration:
interface FastEthernet0/5
switchport access vlan 240
switchport mode access
switchport voice vlan 156
authentication event server dead action authorize vlan 240
authentication event server alive action reinitialize
authentication host-mode multi-domain
authentication order dot1x mab
authentication priority mab
authentication port-control auto
mab
dot1x pae authenticator
spanning-tree portfast
Anyone can help?
Regards,Please check whether the switch is dropping the connection or the server.
Symptoms or Issue
802.1X and MAB authentication and authorization are successful, but the switch is dropping active sessions and the epm session summary command does not display any active sessions.
Conditions
This applies to user sessions that have logged in successfully and are then being terminated by the switch.
Possible Causes
•The preauthentication ACL (and the subsequent DACL enforcement from Cisco ISE) on the NAD may not be configured correctly for that session.
•The preauthentication ACL is configured and the DACL is downloaded from Cisco ISE, but the switch brings the session down.
•Cisco ISE may be enforcing a preposture VLAN assignment rather than the (correct) postposture VLAN, which can also bring down the session.
Resolution
•Ensure the Cisco IOS release on the switch is equal to or more recent than Cisco IOS Release 12.2.(53)SE.
•Check to see whether or not the DACL name in Cisco ISE contains a blank space (possibly around or near a hyphen "-"). There should be no space in the DACL name. Then ensure that the DACL syntax is correct and that it contains no extra spaces.
•Ensure that the following configuration exists on the switch to interpret the DACL properly (if not enabled, the switch may terminate the session):
radius-server attribute 6 on-for-login-auth
radius-server attribute 8 include-in-access-req
radius-server attribute 25 access-request include
radius-server vsa send accounting
radius-server vsa send authentication -
Cisco ISE integration with third-party firewalls
Can Cisco ISE be integrated with a third-party firewall (such as Checkpoint), to provide authentication/authorization services to remote VPN user devices (based on device MAC address)?
The remote user would establish a VPN connection to a third-party firewall, based on a username/password authentication, but the user would only be allowed to send/receive traffic to the internal network if the MAC address of the device being used was authorized by Cisco ISE.
Thank you in advance.Rui,
I do not think the vpn client sends the ip address in a called-station-id, that might be the public ip address that the client is initiating the request from. If you have an existing radius server or can run a packet capture you should be able to verify that.
If the client does send the mac address in the radius packet then you can create a custom condition that can be used to check the mac address along with the username to allow it access to the session. However in VPN deployments there is no concept of profiling since 802.1x deployments usually include the client's mac address.
Thanks,
Tarik Admani
*Please rate helpful posts* -
Cisco ISE - General Info. & capabilities
Hello All,
I've read quiet a bit of ISE features, but would like to know the following:
1. Can ISE provide/track details of user activity, like which servers/websites he accessed over a period of time?
2. Can it provide details of how much data was transferred from a particular server to a specific client?
3. For a 1500 user env. (1000 desktops and 500 wireless devices) which model of ISE would be appropriate?
4. How would having ISE be different from already deployed authentication services like Active Directory or built-in application authentication for solutions like Oracle ERP systems?
5. I see ISE as being marketed primarily for wireles devices (BYOD), but how would it help for wired devices (or does it become and unecessary authentication level apart from AD, switch based 802.1x, etc)
Thank you.
Regards,
AdnanCisco ISE is a consolidated policy-based access control system that incorporates a superset of features available in existing Cisco policy platforms. Cisco ISE performs the following functions:
•Combines authentication, authorization, accounting (AAA), posture, and profiler into one appliance
•Provides for comprehensive guest access management for the Cisco ISE administrator, sanctioned sponsor administrators, or both
•Enforces endpoint compliance by providing comprehensive client provisioning measures and assessing device posture for all endpoints that access the network, including 802.1X environments
•Provides support for discovery, profiling, policy-based placement, and monitoring of endpoint devices on the network
•Enables consistent policy in centralized and distributed deployments that allows services to be delivered where they are needed
•Employs advanced enforcement capabilities including security group access (SGA) through the use of security group tags (SGTs) and security group access control lists (SGACLs)
•Supports scalability to support a number of deployment scenarios from small office to large enterprise environments
The following key functions of Cisco ISE enable you to manage your entire access network.
Provide Identity-Based Network Access
The Cisco ISE solution provides context-aware identity management in the following areas:
•Cisco ISE determines whether users are accessing the network on an authorized, policy-compliant device.
•Cisco ISE establishes user identity, location, and access history, which can be used for compliance and reporting.
•Cisco ISE assigns services based on the assigned user role, group, and associated policy (job role, location, device type, and so on).
•Cisco ISE grants authenticated users with access to specific segments of the network, or specific applications and services, or both, based on authentication results.
ISE 3315 can support 1500 users with appropriate license. -
Cisco ISE functionally and license
HI.
I wanna configure the following on Cisco ISE 1.2.1.
Self-registration portal for guests (SSID: guests)
802.1x user certificate check (Cisco NAM supplicant) for employees (SSID: Corporate) (EAP-TLS)
Self provisioning portal (to deploy BYOD certificate and give access for BYOD devices) for BYOD devices (SSID: Corporate) (PEAP, MSHAPv2)
Can I configure these things with PLUS license or do I need Adv or Wireless? I am not sure if one of these requires profiling functionally.With plus license all the above items should work.
Here is what plus license supports:
Bring Your Own Device (BYOD)
Profiling
Endpoint Protection Service (EPS)
TrustSec SGT
For more info, refer ISE license section:
http://www.cisco.com/c/en/us/td/docs/security/ise/1-2/user_guide/ise_user_guide/ise_man_license.html#41012
Regards,
Jatin Katyal
**Do rate helpful posts** -
Hello all,
Are the Small Business 500 series Switches (ESW520) and Linksys Switches supported by the Cisco Identity Services Engine 1.2.. I didn't see them in the compatibility Matrix ! Is there any way to make them working for ISE wired CWA?
Best Regards.Thank you Venkatesh for the reply,
It's unfortunate to know that ESW500 series doesn't support CWA (because we are deploying ISE and there are many ESW and Linksys Switches here),So Can they support LWA or 802.1X with ISE?
The same questions for Linksys Switches, Can they support CWA, LWA or 802.1X Authentications using ISE?
Thank you so much. -
Cisco ISE (1.3) Posture without Client Provisioning
Hello readers,
Is it possible to set up Cisco ISE with posture without Client Provisioning?
My customer deploys the NAC Agent via MS SCCM. We prefer a access accept + DACL during the pending state instead of redirecting to client provisioning. But the NAC Agent will only communicate when we redirect to client provisioning.
Regards,
DennisWith ISE you can perform 802.1x first and after that optionally you can perform posture. This is done with Radius, that's why it's really and completely out of band, and there's no such concept of trusted or untrusted port because the traffic is never inline.
Still, with ISE you have another option of "inline Posture", in which there's trusted and untrusted ports. I guess that's for some specific cases in which you can't go out-of-band.
On the other hand, so called "out-of-band" NAC was really always an inline solution, only after the user has authenticated and security policies have been verified then the user goes "out-of-band".
Maybe you are looking for
-
How can I save iPhoto Libraries that are in Trash?
Hello. I have been having troubles with iPhoto which are basically cured at the moment. However during the process I had to drag two iPhoto Libraries to my Trash. My iPhoto is working fine at the moment, but I do not want to delete those two in the T
-
Unable to use iTunes for about a month on my PC Have PC with windows 7 (64) Own an iPad2, which is working with no problems When I try to install iTunes it repeatedly fails via "Roll back" Tells me to reinstall, which does not work. Tried latest upd
-
Hi, After trying quite a few print services I now use Apple's via the built in menu option in Aperture. They're consistently good except I find greens such as grass and foilage are coming back too dark. To try to compensate for this when preparing my
-
Duplicate text messages in messages+
I am receiving duplicate text messages when using messages+ as my default app. A msg I send is sent twice & I receive messages twice. This just started about two weeks ago. I have had my galaxy5 for two months. I turned off the stock app yesterd
-
Adobe Reader XI does not open files with a command line "path" argument.
Adobe Reader XI does not open files with a command line "path" argument. Version X and lower all worked fine. I have deleted and reinstalled the program with no success. Is this a bug?