802.1x dynamic vlan assignment with acs5.0

Hi All, Can any one guide me to configure 802.1x with acs 5.0. Its totally new look and m not able to find document related to 802.1x.
Thanks

Hi All, Can any one guide me to
configure 802.1x with acs 5.0. Its totally new look and m not able to
find document related to 802.1x.Thanks
Hi,
Check out the below link on how to configure 802.1x and ACS administration hope to help !!
http://www.cisco.com/en/US/tech/tk389/tk814/technologies_configuration_example09186a00808abf2d.shtml#MDA
Ganesh.H

Similar Messages

802.1x dynamic VLAN assignment with Radius NPS Server

I can NOT get the NPS and Cisco 3550 switch to drop the authenticated user in a VLAN.
I have followed this documentation,
http://msdn.microsoft.com/en-us/library/dd314181(v=ws.10).aspx
that basically says to use these Radius attributes,
Tunnel-Medium-Type : 802
Tunnel-Pvt-Group-ID : My_VLAN_Number (also tried VLAN name)
Tunnel-Type : VLAN
There is some Cisco documentation that says to use Vendor Specific attributes Cisco-AV-Pair,
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst2950/software/release/12-1_19_ea1/configuration/guide/2950scg/swauthen.html#wpxref83693
and I have also tried that,
cisco-avpair= "tunnel-type(#64)=VLAN(13)"
cisco-avpair= "tunnel-medium-type(#65)=802 media(6)"
cisco-avpair= "tunnel-private-group-ID(#81)=vlanid"
My user authenticates on the port fine, but doesn't get put into a VLAN. If I add "sw acc vlan 110" then the user authenticates and then does get an IP address in that VLAN and all is well.
Anybody know how to get dynamic VLAN assignment working with NPS?
NPS on Win 2012 R2
Domain controller separate Win 2012 R2 server
Cisco 3550 switch

Hi All, Can any one guide me to
configure 802.1x with acs 5.0. Its totally new look and m not able to
find document related to 802.1x.Thanks
Hi,
Check out the below link on how to configure 802.1x and ACS administration hope to help !!
http://www.cisco.com/en/US/tech/tk389/tk814/technologies_configuration_example09186a00808abf2d.shtml#MDA
Ganesh.H

Dynamic VLAN Assignment with RADIUS Server and Aironet Access Points

Hi Guys,
I would like to go for "Dynamic VLAN Assignment with RADIUS Server and Aironet Access Points 1300". I want the AP to broadcast only 1 SSID. The client find the SSID ->put in his user credential->Raudius athentication->assign him to an specific vlan based on his groupship.
The problem here is that I don't have a AP controller but only configurable Aironet Access Points 1300. I can connect to the radius server, but I am not sure how to confirgure the AP's port, radio port, vlan and SSID.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml#switch
I go through some references:
3.5 RADIUS-Based VLAN Access Control
As discussed earlier, each SSID is mapped to a default VLAN-ID on the wired side. The IT administrator may wish to impose back end (such as RADIUS)-based VLAN access control using 802.1X or MAC address authentication mechanisms. For example, if the WLAN is set up such that all VLANs use 802.1X and similar encryption mechanisms for WLAN user access, then a user can "hop" from one VLAN to another by simply changing the SSID and successfully authenticating to the access point (using 802.1X). This may not be preferred if the WLAN user is confined to a particular VLAN.
There are two different ways to implement RADIUS-based VLAN access control features:
1. RADIUS-based SSID access control: Upon successful 802.1X or MAC address authentication, the RADIUS server passes back the allowed SSID list for the WLAN user to the access point or bridge. If the user used an SSID on the allowed SSID list, then the user is allowed to associate to the WLAN. Otherwise, the user is disassociated from the access point or bridge.
2. RADIUS-based VLAN assignment: Upon successful 802.1X or MAC address authentication, the RADIUS server assigns the user to a predetermined VLAN-ID on the wired side. The SSID used for WLAN access doesn't matter because the user is always assigned to this predetermined VLAN-ID.
extract from: Wireless Virtual LAN Deployment Guide
http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00801444a1.html
==============================================================
Dynamic VLAN Assignment with RADIUS Server and Wireless LAN Controller Configuration Example
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml#switch
==============================================================
Controller: Wireless Domain Services Configuration
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_configuration_example09186a00801c951f.shtml
Any help on this issue is appreicated.
Thanks.

I'm not sure if the Autonomous APs have the option for AAA Override. On the WLC, I can go into the BSSID, Security, Advanced, and there's a checkbox that I would check to allow a Radius server to send back the VLAN.
I did a little research and it looks like the 1300 may give this option but instead is defined as "VLAN Override". I've found the release notes for 12.3(7)JA5 (not sure what version you're running) that give mention and a link to configuring EAP on page 4: http://www.ciscosystems.ch/en/US/docs/wireless/access_point/1300/release/notes/o37ja5rn.pdf
Hope this helps

WLC- dynamic Vlan assignment with Radius

Hello, we would like to use this feature in our company and because of that I am now testing it. But I found one problem.
I created one testing SSID and two Vlans on WLC. On ACS I use an IETF atributes (064,065,081) for my account and I am changing Vlan ID (081) during testing.
It works with LEAP but when I use PEAP-GTC (which we use commonly in our company) the ip address is not assigned properly (ip which was assigned before remains).
Could you please help me?

There is good document which explains how to configure Dynamic VLAN Assignment with RADIUS Server and Wireless LAN Controller. This will help you. You will find the document at http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml

Dynamic vlan assignment with 1242AG and IAS not working

I'm having trouble getting the dynamic vlan assignment to work on my 1242AG Cisco Aironet APs. I've seen multiple cases with a similar setup and configuration where it works just fine. I've tried everything I can think of. Any suggestions?
IAS and AD is running on Windows Server 2003
Everything works fine except the vlan assignment. Wireless clients successfully authenticate through IAS and Active Directory, but instead of being switched to the appropriate vlan the client stays in whichever vlan/ssid it originally connected to.
PEAP is the authentication method, using MS-CHAP v2. Naturally I have the attributes in the policy set appropriately, ie:
Tunnel-Medium-Type > 802
Tunnel-Pvt-Group-ID > vlanid
Tunnel-Type > VLAN
On the AP:
Cisco 1242AG, C1240 Software (C1240-K9W7-M), Version 12.4(3g)JA, RELEASE SOFTWARE (fc2)
I've attached the config for the AP, which shows that I have two vlans/SSIDs set to cipher, aes, network eap, wpa, etc. I noticed that if the
Tunnel-Pvt-Group-ID attribute is set to a vlan id that doesn't exist on the AP then the AP makes an event log saying so.

Good! Well to answer your questions, IAS is sending numbers, i.e. Tunnel-Pvt-Group-ID > 129
I did view the debug from an AP which showed the Tunnel attributes being recieved from the radius server (I'll have to wait until Monday to get a copy though).
I see I don't have that line "aaa authorization network default group rad_eap",
So I'll have give it a try, (maybe I can remote in so I don't have to wait until Monday).
Thanks,
Jason

802.1x dynamic vlan assignment using ACS 4.2

Hi
we have 10 switches 2960 configured with 802.1x authentication against ACS server 4.2.
we have 2 vlans configured on the switches for administrator and endusers. the end user vlan id is 10 and the administartor vlan is is 100.
we need to apply the following scenario, if the enduser PC - that is connected to vlan 10 - has an issue and the administrator will login to the PC with the administrator account to fix that issue, the switch should dynamically reconfigure the port with the administrator vlan ( 100 ) .
is the above scenario doable using dot1x with the ACS server?
waiting your replies
Mohamed

Hi,
I have the following scenario
2 bulidings with multiple floor
Each floor should be in different VLAN.
The network should be authenticated with 802.1x and each switch port should be assigned with dynamic VLAN from ACS.
Each
user should be able to connect and roam around between any building.
when ever a user is connecting his laptop to any floor, he should be
made part of that respective vlan. It is not requred to have the same
IP rage to be allocated, but the dynamic VLAN should be based on the
switch port location.
Can
I configure ACS in such a way that, the ACS will allocate dynamic VLAN
for every 802.1x authentication based on the Network Device Group.
Please refer the attached diagram
Hi,
Check out the below link for your requirement for dynamic vlan assignement using ACS
http://www.ciscosystems.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml
Hope to Help !!
Ganesh.H
Remember to rate the helpful post

802.1x Dynamic Vlan assignment using ACS

Hi,
I have the following scenario
2 bulidings with multiple floor
Each floor should be in different VLAN.
The network should be authenticated with 802.1x and each switch port should be assigned with dynamic VLAN from ACS.
Each user should be able to connect and roam around between any building. when ever a user is connecting his laptop to any floor, he should be made part of that respective vlan. It is not requred to have the same IP rage to be allocated, but the dynamic VLAN should be based on the switch port location.
Can I configure ACS in such a way that, the ACS will allocate dynamic VLAN for every 802.1x authentication based on the Network Device Group. Please refer the attached diagram

Hi,
I have the following scenario
2 bulidings with multiple floor
Each floor should be in different VLAN.
The network should be authenticated with 802.1x and each switch port should be assigned with dynamic VLAN from ACS.
Each
user should be able to connect and roam around between any building.
when ever a user is connecting his laptop to any floor, he should be
made part of that respective vlan. It is not requred to have the same
IP rage to be allocated, but the dynamic VLAN should be based on the
switch port location.
Can
I configure ACS in such a way that, the ACS will allocate dynamic VLAN
for every 802.1x authentication based on the Network Device Group.
Please refer the attached diagram
Hi,
Check out the below link for your requirement for dynamic vlan assignement using ACS
http://www.ciscosystems.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml
Hope to Help !!
Ganesh.H
Remember to rate the helpful post

Dynamic VLAN assignment with WLC and ACS for

Currently, using our autonomous APs and ACS, our users get separate VLANs per building based on their security level (students or staff). Basically, the student VLAN in one building is different from that of the student VLANs in other buildings on campus. Currently, we do this by filling the Tunnel-Private-Group-ID IETF RADIUS attribute with the VLAN name. This all works because each individual AP can map VLAN names to different VLANs like this:
dot11 vlan-name STUDENT vlan 2903
dot11 vlan-name FACSTAF vlan 2905
As we are working on our WiSM deployment, we see that the document below shows how to do the dynamic VLAN assignment on our WLAN controllers:
http://www.cisco.com/en/US/customer/products/sw/secursw/ps2086/products_configuration_example09186a00808c9bd1.shtml
However, we haven't figured out if it's possible to still provide our users with different VLANs for each building they're in.
With the instructions above, it looks like ACS uses a Cisco RADIUS Attribute to indicate the Air-Interface-Name, mapping an ACS/AD group to a single WLC interface which can only have one VLAN/subnet associated with it.
Does anybody know if what we're trying to accomplish is possible, or if we're really stuck with only one VLAN/subnet per mapped ACS group?

We only have the one WiSM for all of campus, so it's handling everything. This Cisco docs do indicate how to put differnet users in different Vlans, but we don't currently see a way to also put them in different subnets per building.
This being the case, any suggestions on how best to handle more than a Class C subnet's worth of users? Should we just subnet larger than Class C, or is there a more elegant way of handling this?

Dynamic vlan assignment with openldap

Hi,
I have a scenario where my customer has an ACS 5.2 and couple WLCs. the customer has also a openldap database and needs to do dynamic vlan assignement for his wireless user against this database. I know that for Active directory it works, please advise if it does as well for openldap and how?
Regards,

No it doesnt work if you are using mschap v2 here is a grid of the supported eap based protocols and the directory services:
You can find this information here:
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.2/user/guide/eap_pap_phase.html#wp1045863
Hope this helps.

Dynamic vlan assignment with single SSID

Hi All,
I have 300 APs deployed and concurrent client associations that number 3000+ daily
at the moment I have a single subnet for all users, there is no authentication just a click through
page with email entry to gain access.
The APs are assigned to groups based upon the building zone they are in, is it possible to
assign a vlan based upon the AP the user is associated to but still only broadcast a single SSID.
TIA

You can assign dynamic vlan for 802.1X authentication using aaa override from RADIUS server.
In your case, since it is webconsent ssid you can use AP groups to put clients on differnt vlans per the AP group
Sent from Cisco Technical Support iPhone App

802.1x dynamic vlan assignment based on MAC?

Hello,
I am using Catalyst3750 and Widows AD Authentication.
Our customers' pc is runnnig Windows (isn't 802.1x capable) that is connected to the catalyst switch.
Is it possible to dynamic assign a Vlan based on MAC?
When possible, we want to make it without using VMPS.
and, is there any document relating to the above.
Thanks a lot for you help.
Tomoyuki

Hello Tomoyuki,
which Radius Server are you using to authenticate your Clients?
For the Secure ACS you can configure a feature called "MAC-Authentication-Bypass" which fullfils your requirements.
This Feature must be configured on the Switch and on the Radius Server (which does the vlan assigment based on the MAC-Address of the Client)
An Overwiew of this feature can be found here:
http://www.cisco.com/univercd/cc/td/doc/solution/macauthb.pdf
I hope this helps,
Kind regards,
Chris

802.1x RADIUS with EAP-TLS/EAP-TTLS & Dynamic VLAN Assignment

Hello, My team is looking for switches supporting 802.1x authentication on either EAP-TTLS or EAP-TLS protocols with dynamic vlan assignment enabled for these. Looking at the data sheets of the Linksys desktop switches, I found only SLM224G4PS and SLM224G4S models to support EAP-TLS or EAP-TTLS. Am I right? Do they support Dynamic VLAN Assigment for either of those protocols? This is not explicitly mentioned in the data sheets, and I happen to find switches from other manufacturers that announce to support EAP-TLS/EAP-TTLS but no dynamic vlan assignment. Thank you for any help.

SLM switches do support 802.1x RADIUS with EAP-TLS/EAP-TTLS unlike the SRW switches which support MD5. But I don't think that they support Dynamic VLAN.

802.1x authetication with dynamic Vlan assignment by a radius server

Hi
At school I want to start using 802.1x authentication with dynamic Vlan assignment by a Windows Server 2012R2 Radius server.
When a student logs in, I want it to be placed in the "Students" Vlan, when a Administrative employee logs in, I want it to be placed in the "Administative" vlan and when the client is unknown I want to place it in the "Guest" Vlan.
I have several SG200 switches and I configured everything as mentioned in the administrative guide but I cannot get it to work as desired.
What does work:
- If the client is permitted, the switch changes to "authorized" state. (before anyone logs on to the domain with that client)
- When a User logs on that is part of the Administrative employees, the switch changes to "authorized" and when a student logs on, it changes to "unauthorized".
So far so good.
But what doesn't work:
- it does not put the administrative employee in the Vlan "Administrative", it just enables the port on the switch but leaves it in the default vlan 1.
- I can not find the Guest VLAN.
Any help would be appriciated.

Hi Wouter,
Can you see in the packet capture Radius accept message VLAN attribute? Also please ensure you have the latest firmware and boot code:
http://www.cisco.com/c/en/us/support/switches/sg200-26-26-port-gigabit-smart-switch/model.html#~rdtab1
I would recommend you to open ticket with Small Business team so they can go with you through packet capture and configuration steps:
http://www.cisco.com/c/en/us/support/web/tsd-cisco-small-business-support-center-contacts.html
Regards,
Aleksandra

802.1X for wired environments using Radius/ACS for Dynamic Vlan Assignment

Currently Being Moderated
802.1X for wired environments using Radius/ACS for Dynamic Vlan Assignment
Could someone please provide me with a simplest set of configuration steps to fire up Radius in ACS and 802.1X for dynamic vlan assignment. The objective is to roll out NAC L2 OOB using the 802.1X method for dymamic vlan assignments.
If possible show:
1. ACS/Radius Configurations.
2. End User Switch Configurations
Variables:
Switch A
MAC Address aaaa.bbbb.cccc     Vlan 10
            bbbb.cccc.dddd     Vlan 20
Also, if someone posts the Pros and Cons of using Radius/ACS/802.1X for Dynamic Vlan Assignments.
Other technology sets that can be used for Dynamic Vlan assignment EXCEPT from deprecated/obsolete VMPS.
Thanks in advance. .

Hi Guys,
    Hmmm, well if your just looking for Mac based authentication the good news is that is very easy. Just set create your Radius server, ACS, FreeRadius, Steelbelted radius etc. Then create user with the name of the Mac address, in other words if the mac address is 0012.0021.1122 the the name would be 001200211122 and the password would be the mac address. Then you set the vlan and tunnel stuff, like so tunnel-Type would be vlan, Tunnel-medium would be 802 and Tunnel-Private-Group-ID is the name of the vlan(not the vlan number)
   So for the Cisco ACS 4.x you would create a user as specified above, fill in all the password boxes with MAC address, I believe the mac has to be all lower case in the name and the password. Then check the Separate(Chap/MS-Chap/ARAP) box. Then you pick the group the machine belongs to, the group is the part that defines what vlan it is on.
   Before you create the user, create the group with info I wrote above and in addition specify the Service-Type as Authenticate Only.
    Freeradius is a bit harder to configure the specifics and I am just now testing a freeradius server so I do not know the process for Machine authentication.
    If, however, you are trying to authenticate a user that gets a bit trickier and is not so straight forward.

Is dynamic VLAN assignment supported with web-authentication?

The 7.6.130.0 WLC configuration guides says this:
"Dynamic VLAN assignment is not supported for web authentication from a controller with Access Control Server (ACS)"
How should we interpret this, exactly? Does this mean that dynamic VLAN assignment is supported with web authentication from a controller if some other RADIUS server is used (Eg: FreeRadius, ISE)?

It is not supported with any kind of radius server. The radius attributes ACS uses for pushing those settings (64,65,81) are the same for every other radius implementation. Pushing a QoS profile does work.

802.1x dynamic vlan assignment with acs5.0

Similar Messages

Maybe you are looking for