802.1x errors from client in WLAN with WPA2 and PSK
Hello,
I have been doing a client troubleshooting and I have got some errors that does not have so much sense for me:
1)
Time :03/15/2011 14:49:54 CET Severity :ERROR Controller IP :10.x.x.x Message :802.1x authentication message received, static dynamic wep supported.
2)
Time :03/15/2011 14:49:54 CET Severity :INFO Controller IP :10.x.x.x Message :Association request received from a client has an invalid RSN IE.(One reason could be mismatch in WPA2 algorithm).
The WLAN is configured with WPA2 with AES and PSK, and during the troubleshooting several roamings have happened.
Do you have any idea why they can be produced?
I attach the complete log.
Thank you in advanced.
Sounds like the clients are doing WPA with TKIP for the message number 2 for example ?
Similar Messages
-
IPad 3 with iOS 6 fails to connect to WiFi with WPA2 and AES - any solutions available?
Hello *,
after upgrading my iPad 3 to iOS 6 it constantly fails to connect to WiFi with WPA2 and AES - hidden or broadcasted SSID - at home and at work because the device does not accept the WPA2 password. This is also the case for my iPhone 4S but both devices did work with WiFi (WPA2 / AES) perfectly with previously installed iOS 5.1.1.
I tried to downgrade to iOS 5.1.1 but it seems to be no longer possible to downgrade for both iPad 3 and iPhone 4S as the certification and signage window for iOS 5.1.1 maybe has been closed by Apple.
Does anyone know about a possible solution to connect to WiFi with WPA2 and AES with iPad 3 / iPhone 4S and iOS 6 upgrade?
Thank you very much for any help and advise.
Best regards from Germany
MatthiasLook at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
ORA-12541: TNS:no listener error from client mechine
We have oracle 11g server from onsite and I am trying to connect from offshore client.But I am getting error
From SQL plus i am getting the error,
ORA-12541: TNS:no listener
and from SQL Developer I am getting the error,
IO Error:The network adapter could not establish the connection
I am able to Telnet the host with proper port.Onsite peoples able to connect the database from any client using the same TNS names configration I am using.
What are the possibilities to get this errors ?
Please guide me on this.sadasivam wrote:
Hi
Thanks for reply.I checked with onsite DBA for listener and it is up.If you have an on-site DBA why aren't you working with him to solve the problem?
Since you assert that other client machines are able to connect to the database, the issue must be with your own setup. I strongly suspect your tnsnames has a bad entry. Please compare it to the same file from a working client. Also, show us the contents of your tnsnames.ora file.
>
I dont have access of disable the firewall in my clent mechine.I will get it done by network team and post you the status. -
Connection to db fails from client if connecting with sqlplus user/ps@NAME
Hi
I have just installed Oracle client 11.2 on a linux server.
When I connect with sqlplus apmr/******@apm
I am getting:
SQL*Plus: Release 11.2.0.2.0 Production on Thu Mar 29 11:11:17 2012
Copyright (c) 1982, 2010, Oracle. All rights reserved.
ERROR:
ORA-12545: Connect failed because target host or object does not exist
BUT, if I am connecting with /nolog and then insert user/password --> it success!!!
Could anyone solve this mystery ? :-)
sqlplus /nolog
SQL*Plus: Release 11.2.0.2.0 Production on Thu Mar 29 11:12:20 2012
Copyright (c) 1982, 2010, Oracle. All rights reserved.
SQL> conn apmr_larisa@apm
Enter password:
Connected.
Thanks
Larisa884714 wrote:
Thanks a lot for the response. I am getting the following error :
java.sql.SQLException: Io exception: The Network Adapter could not establish the connection.Before asking you to get the help from your DBA, i would suggest to check couple of things like:
1) Write a standalone program and check whether everytime you are getting connection. If answer is yes.
2) Check whether in your web application do jdbc jar's are there (in lib folder) . If answer is yes. Check the version of jars. because the application first checks the dependant jars in application lib folder, if not found then it checks at classpath.
So this might casuse a problem.
If no luck after doing above steps, then i would suggest to ask the DBA, does DB goes down frequently? and show him that error. Because the error is pure say's SID is not up and running. -
End-of-communication channel error from client
In my server oracle(oracle9i enterprices edition) is working fine but from client side i'm getting the following error
*end-of-communication channel error
But my network is working fine
anyone can you give me the solution for this problem....?
Message was edited by:
user497084checkout TNSPING <service name> from cmd prompt
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:\Documents and Settings\NJi>tnsping issl
TNS Ping Utility for 32-bit Windows: Version 2.3.2.1.0 - Production on 25-OCT-06
14:36:06
Copyright , 1996(c) Oracle Corporation 1995. All rights reserved.
Attempting to contact (ADDRESS=(COMMUNITY=tcp.world)(PROTOCOL=TCP)(Host=198.1.2.
15)(Port=1521))
OK (100 msec) -
N91 Podcast client over WLAN with WPA-PSK - downlo...
Hi all,
I'm using a N91 (2.20.008) and the Nokia Podcast Client (1.00.3) to download podcasts via my home network (router Zyxel P-2602HW-D1A). N91 can fine see my network but the connection is unreliable on the N91. I have several laptops and it works fine for them.
What happens is that the podcast client will start to update all podcasts, but nothing happens all the small "circles" just hang. If I try to download one podcast it will sometimes work, but mostly the Podcast client will only download 2% and then hang. Each time I have to drop the WLAN connection and reestablish it to get the next 2%.
So for me it seems that the client waits and waits for something that doesn't happen or some weird loop is taking place.
Is there any fix for this?
N91: 2.20.008
Nokia Podcast Client: 1.00.3
Router: Zyxel P-2602HW-D1A
WLAN Encryption: WPA-PSK
- ChrIvan,
Ok, that makes sense. So yes, as far as I know, the logs are not super helpful when it comes to MAC filtering pass/fail, but you will find generic messages related to MAC filter events. Filtering for MAC is a layer 2 association-level event, so if a client does not pass, you will see an SNMP log message like:
Sun Mar 18 20:23:52 2012 Client Association Failure: MACAddress: Base Radio MAC: Slot: 0 User Name:unknown IP Addr: unknown Reason:Unspecified ReasonCode: 1
If they pass, then you will see:
Sun Mar 18 20:29:05 2012 Client Association: Client MAC: Base Radio MAC : Slot: 0 User Name:unknown IP Addr: unknown
If you are not seeing these messages, make sure you have SNMP trap controls turned on for Client association and association failure events:
I have done some more testing today and I am not running into the issues that you are seeing. In my setup, named clients can associate and unlisted clients are failing to associate. At this point I would recommend that you try upgrading your code to 7.0.220.0 or higher. My testing was done on 7.0.220.0.
Justin -
Error from the session log between Informatica and SAP BI
HI friends,
I am working extraction from bi by Informatica 8.6.1.
now, I start the process Chain from bi, and I got a error from Informatica's session log.Pls help me to figure out what's going on during me execution.
Severity Timestamp Node Thread Message Code Message
INFO 2010-12-17 11:01:31 node01_dcinfa01 DIRECTOR TM_6228 Writing session output to log file [D:\Informatica\PowerCenter8.6.1\server\infa_shared\SessLogs\s_taorh.log].
INFO 2010-12-17 11:01:31 node01_dcinfa01 DIRECTOR TM_6014 Initializing session [s_taorh] at [Fri Dec 17 11:01:31 2010].
INFO 2010-12-17 11:01:31 node01_dcinfa01 DIRECTOR TM_6683 Repository Name: [RepService_dcinfa01]
INFO 2010-12-17 11:01:31 node01_dcinfa01 DIRECTOR TM_6684 Server Name: [IntService_dcinfa01]
INFO 2010-12-17 11:01:31 node01_dcinfa01 DIRECTOR TM_6686 Folder: [xzTraining]
INFO 2010-12-17 11:01:31 node01_dcinfa01 DIRECTOR TM_6685 Workflow: [wf_taorh] Run Instance Name: [] Run Id: [43]
INFO 2010-12-17 11:01:31 node01_dcinfa01 DIRECTOR TM_6101 Mapping name: m_taorh.
INFO 2010-12-17 11:01:31 node01_dcinfa01 DIRECTOR TM_6964 Date format for the Session is [MM/DD/YYYY HH24:MI:SS.US]
INFO 2010-12-17 11:01:31 node01_dcinfa01 DIRECTOR TM_6703 Session [s_taorh] is run by 32-bit Integration Service [node01_dcinfa01], version [8.6.1], build [1218].
INFO 2010-12-17 11:01:31 node01_dcinfa01 MANAGER PETL_24058 Running Partition Group [1].
INFO 2010-12-17 11:01:31 node01_dcinfa01 MANAGER PETL_24000 Parallel Pipeline Engine initializing.
INFO 2010-12-17 11:01:31 node01_dcinfa01 MANAGER PETL_24001 Parallel Pipeline Engine running.
INFO 2010-12-17 11:01:31 node01_dcinfa01 MANAGER PETL_24003 Initializing session run.
INFO 2010-12-17 11:01:31 node01_dcinfa01 MAPPING CMN_1569 Server Mode: [UNICODE]
INFO 2010-12-17 11:01:31 node01_dcinfa01 MAPPING CMN_1570 Server Code page: [MS Windows Simplified Chinese, superset of GB 2312-80, EUC encoding]
INFO 2010-12-17 11:01:31 node01_dcinfa01 MAPPING TM_6151 The session sort order is [Binary].
INFO 2010-12-17 11:01:31 node01_dcinfa01 MAPPING TM_6156 Using low precision processing.
INFO 2010-12-17 11:01:31 node01_dcinfa01 MAPPING TM_6180 Deadlock retry logic will not be implemented.
INFO 2010-12-17 11:01:31 node01_dcinfa01 MAPPING SDKS_38029 Loaded plug-in 300320: [PowerExchange for SAP BW - OHS reader plugin 8.6.1 build 183].
INFO 2010-12-17 11:01:31 node01_dcinfa01 MAPPING SDKS_38024 Plug-in 300320 initialization complete.
INFO 2010-12-17 11:01:31 node01_dcinfa01 MAPPING PCCL_97003 [WARNING] Real-time session is not enabled for source [AMGDSQ_IS_TAORH]. Real-time Flush Latency value must be 1 or higher for a session to run in real time.
INFO 2010-12-17 11:01:31 node01_dcinfa01 MAPPING SDKS_38016 Reader SDK plug-in intialization complete.
INFO 2010-12-17 11:01:31 node01_dcinfa01 MAPPING TM_6307 DTM error log disabled.
INFO 2010-12-17 11:01:31 node01_dcinfa01 MAPPING TE_7022 TShmWriter: Initialized
INFO 2010-12-17 11:01:31 node01_dcinfa01 MAPPING TM_6007 DTM initialized successfully for session [s_taorh]
INFO 2010-12-17 11:01:31 node01_dcinfa01 DIRECTOR PETL_24033 All DTM Connection Info: [<NONE>].
INFO 2010-12-17 11:01:31 node01_dcinfa01 MANAGER PETL_24004 PETL_24004 Starting pre-session tasks. : (Fri Dec 17 11:01:31 2010)
INFO 2010-12-17 11:01:31 node01_dcinfa01 MANAGER PETL_24027 PETL_24027 Pre-session task completed successfully. : (Fri Dec 17 11:01:31 2010)
INFO 2010-12-17 11:01:31 node01_dcinfa01 DIRECTOR PETL_24006 Starting data movement.
INFO 2010-12-17 11:01:31 node01_dcinfa01 MAPPING TM_6660 Total Buffer Pool size is 1219648 bytes and Block size is 65536 bytes.
INFO 2010-12-17 11:01:31 node01_dcinfa01 READER_1_1_1 OHS_99013 [INFO] Partition 0: Connecting to SAP system with DESTINATION = sapbw, USER = taorh, CLIENT = 800, LANGUAGE = en
INFO 2010-12-17 11:01:32 node01_dcinfa01 READER_1_1_1 OHS_99016 [INFO] Partition 0: BW extraction for Request ID [163] has started.
Edited by: bi_tao on Dec 18, 2010 11:46 AMINFO 2010-12-17 11:01:33 node01_dcinfa01 WRITER_1_*_1 WRT_8167 Start loading table [VENDOR] at: Fri Dec 17 11:01:32 2010
INFO 2010-12-17 11:01:33 node01_dcinfa01 WRITER_1_*_1 WRT_8168 End loading table [VENDOR] at: Fri Dec 17 11:01:32 2010
INFO 2010-12-17 11:01:33 node01_dcinfa01 WRITER_1_*_1 WRT_8141
Commit on end-of-data Fri Dec 17 11:01:32 2010
===================================================
WRT_8036 Target: VENDOR (Instance Name: [VENDOR])
WRT_8044 No data loaded for this target
INFO 2010-12-17 11:01:33 node01_dcinfa01 WRITER_1_*_1 WRT_8143
Commit at end of Load Order Group Fri Dec 17 11:01:32 2010
===================================================
WRT_8036 Target: VENDOR (Instance Name: [VENDOR])
WRT_8044 No data loaded for this target
INFO 2010-12-17 11:01:33 node01_dcinfa01 WRITER_1_*_1 WRT_8035 Load complete time: Fri Dec 17 11:01:32 2010
LOAD SUMMARY
============
WRT_8036 Target: VENDOR (Instance Name: [VENDOR])
WRT_8044 No data loaded for this target
INFO 2010-12-17 11:01:33 node01_dcinfa01 WRITER_1_*_1 WRT_8043 ****END LOAD SESSION****
INFO 2010-12-17 11:01:33 node01_dcinfa01 WRITER_1_*_1 WRT_8006 Writer run completed.
INFO 2010-12-17 11:01:33 node01_dcinfa01 MANAGER PETL_24031
RUN INFO FOR TGT LOAD ORDER GROUP [1], CONCURRENT SET [1] *****
Thread [READER_1_1_1] created for [the read stage] of partition point [AMGDSQ_IS_TAORH] has completed. The total run time was insufficient for any meaningful statistics.
Thread [TRANSF_1_1_1] created for [the transformation stage] of partition point [AMGDSQ_IS_TAORH] has completed. The total run time was insufficient for any meaningful statistics.
Thread [WRITER_1_*_1] created for [the write stage] of partition point [VENDOR] has completed. The total run time was insufficient for any meaningful statistics.
INFO 2010-12-17 11:01:33 node01_dcinfa01 MANAGER PETL_24005 PETL_24005 Starting post-session tasks. : (Fri Dec 17 11:01:33 2010)
INFO 2010-12-17 11:01:33 node01_dcinfa01 MANAGER PETL_24029 PETL_24029 Post-session task completed successfully. : (Fri Dec 17 11:01:33 2010)
INFO 2010-12-17 11:01:33 node01_dcinfa01 MAPPING SDKS_38025 Plug-in 300320 deinitialized and unloaded with status [-1].
INFO 2010-12-17 11:01:33 node01_dcinfa01 MAPPING SDKS_38018 Reader SDK plug-ins deinitialized with status [-1].
INFO 2010-12-17 11:01:33 node01_dcinfa01 MAPPING TM_6018 The session completed with [0] row transformation errors.
INFO 2010-12-17 11:01:33 node01_dcinfa01 MANAGER PETL_24002 Parallel Pipeline Engine finished.
INFO 2010-12-17 11:01:33 node01_dcinfa01 DIRECTOR PETL_24013 Session run completed with failure.
INFO 2010-12-17 11:01:34 node01_dcinfa01 DIRECTOR TM_6022
SESSION LOAD SUMMARY
================================================
INFO 2010-12-17 11:01:34 node01_dcinfa01 DIRECTOR TM_6252 Source Load Summary.
INFO 2010-12-17 11:01:34 node01_dcinfa01 DIRECTOR CMN_1537 Table: [AMGDSQ_IS_TAORH] (Instance Name: [AMGDSQ_IS_TAORH]) with group id[1] with view name [Group1]
Rows Output [0], Rows Affected [0], Rows Applied [0], Rows Rejected[0]
INFO 2010-12-17 11:01:34 node01_dcinfa01 DIRECTOR TM_6253 Target Load Summary.
INFO 2010-12-17 11:01:34 node01_dcinfa01 DIRECTOR CMN_1740 Table: [VENDOR] (Instance Name: [VENDOR])
Output Rows [0], Affected Rows [0], Applied Rows [0], Rejected Rows [0]
INFO 2010-12-17 11:01:34 node01_dcinfa01 DIRECTOR TM_6023
===================================================
INFO 2010-12-17 11:01:34 node01_dcinfa01 DIRECTOR TM_6020 Session [s_taorh] completed at [Fri Dec 17 11:01:33 2010]. -
Runtime error in Dynamic internal table with AMOUNT and Quantity Fields..
Dear friends,
I am attempting write a dymanic Select Statement (with joins).
And the sleect query looks like this..
SELECT (LT_SEL_LIST)
INTO CORRESPONDING FIELDS OF
TABLE <DYN_TABLE>
FROM (LT_FROM_LIST)
WHERE (LT_WHERE3).
Here the into table is a dynamically created internal table..
which is created by ...this
CALL METHOD CL_ALV_TABLE_CREATE=>CREATE_DYNAMIC_TABLE
EXPORTING
IT_FIELDCATALOG = IT_OUTPUT2[]
IMPORTING
EP_TABLE = DY_TABLE.
the it_output2 contains the the fieldcatlog information of dynamically given fields :-
like:-
TABNAME
FIELDNAME
DATATYPE
LENG
INTTYPE
ROLLNAME
DECIMALS
REFTABLE
REFFIELD
i mean the internal table is constructed with reference to all the bove metadata.
Problem:- This query run fine with all the fields Except AMOUNT AND QUANTITY fields....
When the selection list contain VBAK-NETWR or MSEG-MENGE..It throws a runtime error.
"The data read during a SLECT access couldnt be inserted into the target field,either conversion is not supported for
the target field's type or the target field is too short."
after this I even tried to construct the dynamic table with CFILEDNAME and QFIELDNAME in the Fieldcatalog.
so now my fieldcatlog looks like this:---
LOOP AT IT_DD03L..
IF IT_DD03L-DATATYPE = 'CURR'.
TABLEFIELD-CFIELDNAME = IT_DD03L-FIELDNAME .
ENDIF.
IF IT_FIELDCAT3-DATATYPE = 'QUAN'.
TABLEFIELD-QFIELDNAME = IT_DD03L-FIELDNAME .
ENDIF.
TABLEFIELD-TABNAME = IT_DD03L-TABNAME.
TABLEFIELD-FIELDNAME = IT_DD03L-FIELDNAME.
TABLEFIELD-DATATYPE = IT_DD03L-DATATYPE.
TABLEFIELD-INTLEN = IT_DD03L-LENG.
TABLEFIELD-INTTYPE = IT_DD03L-INTTYPE .
TABLEFIELD-ROLLNAME = IT_DD03L-ROLLNAME.
TABLEFIELD-DECIMALS = IT_DD03L-DECIMALS.
TABLEFIELD-REF_TABLE = IT_DD03L-REFTABLE.
TABLEFIELD-REF_FIELD = IT_DD03L-REFFIELD.
APPEND TABLEFIELD.
CLEAR TABLEFIELD.
ENDLOOP.
Note:- this is a test code so ignore performance issues...
Please help me with some code ...to avoid the Runtime erorr.
Thanks,
jeevan.Hi Jeevan,
Why are moving only few fields from DD03L table to your field catalog? Why don't you use move-corresponding? The following code works for me in ECC6.0.
data: it_dd03l type table of dd03l initial size 0,
ls_dd03l type dd03l,
lt_fldcat TYPE lvc_t_fcat,
ls_fldcat TYPE lvc_s_fcat,
ls_where(72) TYPE c,
lt_where LIKE TABLE OF ls_where,
lt_fld LIKE TABLE OF ls_where,
lt_data_dy TYPE REF TO data.
field-symbols: <ft_data> TYPE STANDARD TABLE.
select * into table it_dd03l from dd03l
where tabname = 'VBAK'
and ( fieldname = 'VBELN' or fieldname = 'NETWR' ).
check sy-subrc eq 0.
loop at it_dd03l into ls_dd03l.
move-corresponding ls_dd03l to ls_fldcat.
append ls_fldcat to lt_fldcat.
move ls_dd03l-fieldname to ls_where.
append ls_where to lt_fld.
if ls_dd03l-fieldname = 'VBELN'.
clear ls_where.
concatenate ls_dd03l-fieldname ' <> ''''' into ls_where.
append ls_where to lt_where.
endif.
endloop.
check not lt_fldcat is initial.
CALL METHOD cl_alv_table_create=>create_dynamic_table
EXPORTING
it_fieldcatalog = lt_fldcat
IMPORTING
ep_table = lt_data_dy
EXCEPTIONS
generate_subpool_dir_full = 1
OTHERS = 2.
IF sy-subrc <> 0.
RAISE no_configuration_data.
ENDIF.
ASSIGN lt_data_dy->* TO <ft_data>.
check sy-subrc eq 0.
select (lt_fld) from VBAK into corresponding fields of table
<ft_data>
where (lt_where).
Thanks
Bala -
MS SQL Server 2014: Error inserting into Temp table with index and identity field
In this thread, I mentioned a problem with SQL Server 2014:
SQL Server 2014: Bug with IDENTITY INSERT ON
The question was answered, it is a bug. To keep you informed on this issue, I open this discussion.
Problem:
The code below works perfectly fine on MS SQL Server 2008 R2 and MS SQL Server 2012, but gives an error every second time the proc is executed on MS SQL Server 2014. If I do not define any index on the temp table, the problem disappears. Defining the index
after the insert, does not help.
SET NOCOUNT ON
GO
IF EXISTS (SELECT 1 FROM sys.procedures WHERE name = 'usp_Test') DROP PROC dbo.usp_Test;
GO
CREATE PROC dbo.usp_Test AS
BEGIN
SET NOCOUNT ON
CREATE TABLE #Source(ID integer NOT NULL);
INSERT INTO #Source VALUES (1), (2), (3);
CREATE TABLE #Dest (ID integer IDENTITY(1,1) NOT NULL);
CREATE INDEX #IDX_Dest ON #Dest (ID);
PRINT 'Check if the insert might cause an identity crisis';
SELECT 'Source' AS SourceTable, * FROM #Source;
SELECT 'Destination' AS DestTable, * FROM #Dest;
SET IDENTITY_INSERT #Dest ON;
PRINT 'Do the insert';
INSERT INTO #Dest (ID) SELECT ID FROM #Source;
PRINT 'Insert ready';
SET IDENTITY_INSERT #Dest OFF;
SELECT * FROM #Dest;
DROP TABLE #Source;
DROP TABLE #Dest;
END;
GO
PRINT 'First execution of the proc, everything OK';
EXEC dbo.usp_Test;
PRINT '';
PRINT 'Second execution of the proc, the insert fails.';
PRINT 'Removing the index #IDX_Dest causes the error to disappear.';
EXEC dbo.usp_Test;
GO
DROP PROC dbo.usp_Test;
GOThere is some progress. Communication from a former Microsoft employee tells us this:
Shivendra Vishal
Engineer at Microsoft
I am no longer with MS, and I do not have code access, however from the public symbols, I could make out following:
sqlmin!SetidentI2I4+0x1f3:
000007fe`f4d865d3 488b10 mov rdx,qword ptr [rax] ds:00000000`00000000=????????????????
ExceptionAddress: 000007fef4d865d3 (sqlmin!SetidentI2I4+0x00000000000001f3)
ExceptionCode: c0000005 (Access violation)
ExceptionFlags: 00000000
NumberParameters: 2
Parameter[0]: 0000000000000000
Parameter[1]: 0000000000000000
Attempt to read from address 0000000000000000
This is a read AV and from registers it is clear that we were trying to move the value of location pointed by qword of register rax which is not valid:
rax=0000000000000000 rbx=0000000000000038 rcx=0000000000001030
rdx=0000000000000006 rsi=00000001f55def98 rdi=00000000106fd070
rip=000007fef4d865d3 rsp=00000000106fcf40 rbp=00000000106fcfe9
r8=0000000000000000 r9=00000001f55def60 r10=00000001f55defa0
r11=00000000106fcd20 r12=0000000000000000 r13=0000000000000002
r14=00000001f49c3860 r15=00000001f58c0040
iopl=0 nv up ei pl nz na po nc
cs=0033 ss=002b ds=002b es=002b fs=0053 gs=002b efl=00010206
The stack is:
# Child-SP RetAddr Call Site
00 00000000`106fcf40 000007fe`f30c1437 sqlmin!SetidentI2I4+0x1f3
01 00000000`106fd050 000007fe`f474e7ce sqlTsEs!CEsExec::GeneralEval4+0xe7
02 00000000`106fd120 000007fe`f470e6ef sqlmin!CQScanUpdateNew::GetRow+0x43d
03 00000000`106fd1d0 000007fe`f08ff517 sqlmin!CQueryScan::GetRow+0x81
04 00000000`106fd200 000007fe`f091cebe sqllang!CXStmtQuery::ErsqExecuteQuery+0x36d
05 00000000`106fd390 000007fe`f091ccb9 sqllang!CXStmtDML::XretDMLExecute+0x2ee
06 00000000`106fd480 000007fe`f08fa058 sqllang!CXStmtDML::XretExecute+0xad
07 00000000`106fd4b0 000007fe`f08fb66b sqllang!CMsqlExecContext::ExecuteStmts<1,1>+0x427
08 00000000`106fd5f0 000007fe`f08fac2e sqllang!CMsqlExecContext::FExecute+0xa33
09 00000000`106fd7e0 000007fe`f152cfaa sqllang!CSQLSource::Execute+0x86c
0a 00000000`106fd9b0 000007fe`f152c9e8 sqllang!CStmtExecProc::XretLocalExec+0x25a
0b 00000000`106fda30 000007fe`f152a1d8 sqllang!CStmtExecProc::XretExecExecute+0x4e8
0c 00000000`106fe1e0 000007fe`f08fa058 sqllang!CXStmtExecProc::XretExecute+0x38
0d 00000000`106fe220 000007fe`f08fb66b sqllang!CMsqlExecContext::ExecuteStmts<1,1>+0x427
0e 00000000`106fe360 000007fe`f08fac2e sqllang!CMsqlExecContext::FExecute+0xa33
0f 00000000`106fe550 000007fe`f0902267 sqllang!CSQLSource::Execute+0x86c
10 00000000`106fe720 000007fe`f0909087 sqllang!process_request+0xa57
11 00000000`106feee0 000007fe`f2bf49d0 sqllang!process_commands+0x4a3
12 00000000`106ff200 000007fe`f2bf47b4 sqldk!SOS_Task::Param::Execute+0x21e
13 00000000`106ff800 000007fe`f2bf45b6 sqldk!SOS_Scheduler::RunTask+0xa8
14 00000000`106ff870 000007fe`f2c136ff sqldk!SOS_Scheduler::ProcessTasks+0x279
15 00000000`106ff8f0 000007fe`f2c138f0 sqldk!SchedulerManager::WorkerEntryPoint+0x24c
16 00000000`106ff990 000007fe`f2c13246 sqldk!SystemThread::RunWorker+0x8f
17 00000000`106ff9c0 000007fe`f2c13558 sqldk!SystemThreadDispatcher::ProcessWorker+0x3ab
18 00000000`106ffa70 00000000`775d59ed sqldk!SchedulerManager::ThreadEntryPoint+0x226
19 00000000`106ffb10 00000000`7780c541 kernel32!BaseThreadInitThunk+0xd
1a 00000000`106ffb40 00000000`00000000 ntdll!RtlUserThreadStart+0x21
Unassembling the function:
000007fe`f4d8658e 4c8b10 mov r10,qword ptr [rax]
000007fe`f4d86591 4533e4 xor r12d,r12d
000007fe`f4d86594 410fb7d5 movzx edx,r13w
000007fe`f4d86598 4533c9 xor r9d,r9d
000007fe`f4d8659b 4533c0 xor r8d,r8d
000007fe`f4d8659e 488bc8 mov rcx,rax
000007fe`f4d865a1 4489642420 mov dword ptr [rsp+20h],r12d
000007fe`f4d865a6 41ff5230 call qword ptr [r10+30h]
000007fe`f4d865aa 8b5597 mov edx,dword ptr [rbp-69h]
000007fe`f4d865ad 4c8b10 mov r10,qword ptr [rax]
000007fe`f4d865b0 4489642438 mov dword ptr [rsp+38h],r12d
000007fe`f4d865b5 4489642430 mov dword ptr [rsp+30h],r12d
000007fe`f4d865ba 458d442401 lea r8d,[r12+1]
000007fe`f4d865bf 4533c9 xor r9d,r9d
000007fe`f4d865c2 488bc8 mov rcx,rax
000007fe`f4d865c5 c644242801 mov byte ptr [rsp+28h],1
000007fe`f4d865ca 4488642420 mov byte ptr [rsp+20h],r12b
000007fe`f4d865cf 41ff5250 call qword ptr [r10+50h]
000007fe`f4d865d3 488b10 mov rdx,qword ptr [rax] <=================== AV happened over here
000007fe`f4d865d6 488bc8 mov rcx,rax
000007fe`f4d865d9 4c8bf0 mov r14,rax
000007fe`f4d865dc ff5268 call qword ptr [rdx+68h]
000007fe`f4d865df 488d55e7 lea rdx,[rbp-19h]
000007fe`f4d865e3 4c8b00 mov r8,qword ptr [rax]
000007fe`f4d865e6 488bc8 mov rcx,rax
000007fe`f4d865e9 41ff5010 call qword ptr [r8+10h]
000007fe`f4d865ed f6450a04 test byte ptr [rbp+0Ah],4
I remember few issues with scan2ident function, I am not sure if they have fixed it however it appears that this is intoduced to SQL 2014 and we need help from MS to get this resolved as it needs code analysis.
It is not getting simulated for other versions of SQL apart from SQL 2014.
Also to add, interestingly, the value of rax is not visibly changed and it was successfully passed on to rcx, which has a valid value, so something should have changed the value of rax inside call to function using call qword ptr [r10+50h], and looking at this
it appears that it might be a list of functions and we are going at particular offset [50h]. So, bottom line is that the call to function qword ptr [r10+50h], should be changing something in rax, and debugging/analyzing this code might give us some more idea. -
Error installing sap 2004s SR1 with DB2 and AIX
Hello Gurus,
I am installing MySap 2004s SR1 with DB2 and IBM AIX.
I am facing the following error :
<b>ERROR 2006-11-09 02:21:22
MDB-01052 Could not connect to database: DB6CliConnectUser(): [IBM][CLI Driver] SQL30082N Attempt to establish connection failed with security reason "1" ("PASSWORD EXPIRED"). SQLSTATE=08001
ERROR 2006-11-09 02:21:22
FCO-00011 The step CreateNodegroups with step key |NW_Onehost|ind|ind|ind|ind|0|0|NW_Onehost_System|ind|ind|ind|ind|1|0|NW_CreateDBandLoad|ind|ind|ind|ind|9|0|NW_CreateDB|ind|ind|ind|ind|0|0|NW_DB6_DB|ind|ind|ind|ind|1|0|NW_DB6_CreateNodegroups|ind|ind|ind|ind|17|0|CreateNodegroups was executed with status ERROR .</b>
Please help me out.
Thanks,
Chandra Sekhar Reddy.Hi,
... ("PASSWORD EXPIRED") ...
Try to log on OS level with db2<sid>, <sid>adm and sap<sid>/sapr3 (not from root level, but rather by providing a username / pw combination).
Most probably the password on OS level has expired.
Please be aware, that you have to use dscdb6up to change passwords for <sid>adm and sap<sid>.
HJ -
Running two SSIDs, one with WPA2 and one with WEP
Hi,
I have a WRT610N.
How isolated are the two SSIDs that I can run?
I know one is running at 5GHz and the other at 2.4GHz. I've given each an SSID and a different security policy: I run "sensitive" stuff under WPA2, and I run the other for legacy hardware that supports only WEP (eg my son's Nintento DS).
But are these two keys to the same house, so to speak? If someone cracks my WEP network, can they access the machines on the WPA network? Or are they completely isolated?
Does this make sense?
Thanks for any enlightenment.
-- Mike
Solved!
Go to Solution.Yes, they are "two keys to the same house". The "house" is your LAN. If someone cracks your WEP, and wirelessly breaks into your router, then they have access to your LAN. This would be like allowing a hacker to wire his computer directly to your router. Being on your LAN, puts the hacker in a very good position to break into any other computer on your network. Your WPA2 encryption does not give you any protection from someone who is already on your LAN.
The solution to your problem is to run two separate wireless routers:
modem ---- router1 --- router2
router1 is set to "Local IP address" 192.168.1.1 , WEP encryption , set "AP isolation" to "enabled" , (note: no printers on router1)
router2 is set to "Local IP address" 192.168.2.1 , WPA2 encryption, use a strong password (and not anything similar to the WEP password).
modem is wired to Internet port of router1
LAN port of router1 is wired to Internet port of router2
The wireless 2.4 GHz channels on the two routers must be different, and are preferably at least 5 channels apart. Usually channels 1, 6, or 11 work best.
With the above two router setup, the Internet port of router2 should protect you from any intruders on router1. -
1240AG WPA2 and PSK for non radius clients
does this device support this options?
We want to move to WPA2 enterprise and use our radius server (windows IAS), but we want to hand out a key to non domain computers. We have production machines that arent on the domain for various reasons.
2nd question, does the AP allow for creating a 2nd "Guest" wireless for visitors?
thanks!Hi Shayne,
The Cisco 1240 supports WPA2/AES.Yes, the can provide different security policys via different SSIDs. For example:
SSID#1 - Corporate - WPA2/AES 802.1X
SSID#2 - CorporatePSK - WPA2/AES PSK
SSID#3 - Guest
There is a good deal of configuration to make this happen. But yes this is supported..
Here is a link how to configure SSIDs on a autonomous access points
http://www.cisco.com/en/US/docs/wireless/access_point/12.3_7_JA/configuration/guide/s37ssid.html
Please be so kind to rate helpful post! -
Getting an vierd error from client
Hi,
When connecting to DB from the client we are getting this error:
Attempted to read or write protected memory. This is often an indication that other memory is corrupt.
at Oracle.DataAccess.Client.OpsCon.AllocValCtx(OpoConValCtx*& pOpoConValCtx)
at Oracle.DataAccess.Client.OracleConnection.Open()
at LibraryServices.Lt.WebApp.Login.DoLogin()
Attempted to read or write protected memory. This is often an indication that other memory is corrupt.
at Oracle.DataAccess.Client.OpsCon.AddRef(IntPtr pOpsConCtx)
at Oracle.DataAccess.Client.OracleCommand.CheckConStatus()
at Oracle.DataAccess.Client.OracleCommand.ExecuteReader(Boolean requery, Boolean fillRequest, CommandBehavior behavior)
at Oracle.DataAccess.Client.OracleCommand.ExecuteReader()
at LibraryServices.Lt.WebApp.Login.DoLogin()
ThanksHi,
We have installed different version of odp.net into a different directory other than oracle_home of client. Then without uninstalling again we have installed odp.net into the directory in oracle_home.
That's when the problem started. Is there anything we can do it normal?
Thanks
Edited by: user604101 on Oct 8, 2008 10:59 AM -
Error from labview 6.1 with the system windows 7
I use Labview 6.1 vi to control a Tektronic oscilloscope and a BNC universal pulse generator via GPIB-USP connection. The vi worked very well with the system windows XP. The system was changed to Windows 7. Then one error message (Trigger signal is not recognized. Check the connection between 'Trigger out' and 'Aux in') comes whenever I start to run vi. The connection between 'Trigger out' and 'Aux in' works under mannual mode, so it is really ok.
Could the compatibility between Labview 6.1 and windows 7 be the reason? If yes, are there tricks to use Labview 6.1 on windows 7? Thanks.
Solved!
Go to Solution.I do not know coding with Labview actually.....
I set the pulse generator to mannual mode and send pulsing signal to scope. The signal was received well and displayed by the scope. It means the connection between 'Trigger out' and 'Aux in' is ok.
The record of NI I/O interface is attached when the error message comes.
Thanks.
Attachments:
Capture.txt 85 KB -
Getting a syntax error from mx.transitions.Tween with flash CS4
Hello all!
I am getting an import error with the following libraries:
import mx.transitions.Tween;
import mx.transitions.easing.*;
The errors are like this one:
Definition fl.transitions:Tween could not be found
I am using it as part of my .fla where for sorme reason it does not work but it works fine in the original archive. I guess it is a problem with the action script version becouse the original template use as2 and I am using as3.
Does anyone know which are the equivalent libraries in as3???
May I import does libraries directly in as3?
Thanks in advance for your helpin as3, you should use:
import fl.transitions.Tween;
import fl.transitions.easing.*;
NOT
import mx.transitions.Tween;
import mx.transitions.easing.*;
(see the difference?)
Maybe you are looking for
-
Visual Studio 2013 WP Emulator not working after adding more RAM
After a few days I installed VS 2013 on my laptop which had 3GB RAM and got notified by visual studio that I need at least 4 GB for hardware virtualization. Now I have 6GB RAM and Hyper-V restarted and VS still doesn't recognize my new RAM and doesn'
-
Device issue with WLC (excluded client)
I have a single client that is having issues staying connected to my WLC running code 7.0.220.0 Here are the debugs, it just keeps on looping: *apfMsConnTask_0: Jul 18 10:41:06.352: 00:40:96:b8:78:7a Adding mobile on LWAPP AP 10:8c:cf:78:93:80(0) *ap
-
I have for the last two weeks tried to upgrade Snow Leopard each had time give up as after I have successfully downloaded I attempt to go through the process of upgrading nothing happens at the stage of 'Install' I have checked the installation log a
-
what is building blocks in SAP-SD? and how it is prepare?
-
Unable to Copy to Purchase Order from a Quotation
Hi All, Can anyone help with this problem: When I try to copy to a PO fro a PQ I get an error msg ' No matching records ODBC-2028'. This message appears after the PO form has opened with no lines copied. Thanks Martin