808 moving wlan access point

I've setup my wlan access in Internet destination. In this destination I set up wlan as priority 1 and mobile data as priority 2. Phone keeps moving wlan from Internet to Uncategorised destination. If I move it back to Internet it stays for some time and goes back to Uncategorised. Sometimes it happens while browsing. I want to go back one page and phone will show that it can't find the address. Have to go to settings and move it back to Internet destination. Ad nauseam. Did not have this problem on N8. My phone has static IP address on my home modem. Is there a cure for that?

I have seen this happen on my 808 too. Cannot remember what I was doing at the time, but definitely it had nothing to do with re-organizing APs. However, suddenly there was Uncategorised destination in my access point settings with one WLAN AP in it.
There is also an another bug in the WLAN settings, which I have described in detail at Connectivity Tips and Troubleshooting subforum. Please see:
http://discussions.nokia.com/t5/Connectivity/Nokia-808-Belle-FP1-bug-WLAN-works-but-not-all-apps-can...

Similar Messages

WLAN access point "missing" when connection alread...

Hello,
I have an E63 with version 400.21.013 firmware. However, I have experienced this problem from day one. I do not have a data plan but I use WLAN at various locations, and there is a list of access points in the Settings.
I have a home access point configured with WPA2 and I have all the settings saved in the Connection Manager (or is it WLAN Wizard - I don't know). When the phone is not connected to any AP and I use a program that wants data, it will almost always show the "Home" AP in the list which appears right after "Searching for available access points" is briefly displayed. "Home" shows up right below Search for WLAN. There is no problem making the first connection.
However, if the "Home" AP is already in use and I open another program that wants data, at times it will not show my Home AP in the list. If "Searching for available access points" is only displayed for a split second, "Home" will not be in the list. Sometimes I can close the program and open it again and if "Searching for available access points" stays on screen for about a second, then "Home" will be on the list and I can connect. Sometimes I will have to try 3, 4, 5 times, and sometimes it will never "see" the AP unless I disconnect the WLAN and start all over.
Right at this moment, there is no problem. I can open program after program and connect via my "Home" AP. But it is frustrating when it does happen. Has anyone seen this or found a remedy?
Thanks.

Have you tried changing the WLAN channel (i.e. frequency) of your home WLAN access point / router?
Try switching between few different channels (like 1, 3, 6, 9, 11) to see if some channel happens to work more reliably. It is possible that there is some radio interference (neighbouring WLAN networks, cordless phones, Bluetooth devices etc.) on the currently used WLAN channel, causing phone to discover this network less reliably.
In case your WLAN access point / router includes 802.11n support, make sure that your AP's "channel width" is set to a standard 20MHz mode (instead 20/40MHz).
This is a bit long shot suggestion (just guessing), but if switching the WLAN channel related setting on the AP doesn't help then you could also try editing your phone's access point (the one created for you home WLAN network, under Tools -> Settings -> Connection -> Access Points) so that your phone should consider this particular WLAN network as an "Hidden SSID" (even if network really isn't hidden) by changing the "Network status" setting from Public to Hidden.

Can I use my Apple TV as an WLAN Access Point?

In my Basement I have a LAN Connection but no WIFI and no Cellular. Therefore I would highly appreciate if I could use connect my iPad via WLAN with the Apple TV and to get Internet access which is routed thru the Apple TV.
So I am looking forward for upcomming Updates.

.... maybe it could be an Idea to add this functionality.
So Apple TV could combine the functionality of
AirPort Express http://www.apple.com/airport-express/
and WLAN Repeater
e.g. http://www.avm.de/de/Produkte/FRITZ_WLAN/FRITZ_WLAN_Repeater_300E/index.php
or
http://www.avm.de/de/Produkte/FRITZPowerline/index.php

Apple TV as Airport access point if connected via LAN

Hi!
I thought about the possibility to use the new Apple TV as Airport/WLAN access point in the case that it is connected via LAN. You don't need an Airport Express and you got Airport/WLAN/HDMI/Audio in all rooms (and around that room) you connect an Apple TV to. Nice and best for hotels!
Vice versa: If you connect it via Airport to use the ethernet port as a hub/switch to connect devices. I think this should be possible and hope that it's only a firmware update...
Next step is not only to playback videos/photos from other devices. Just use it as a main or second screen for all kind of devices (Computer Extensions forMac OS X/Windows other will follow...).
You don't have to connect a notebook to a beamer anymore. There's only the AppleTV connected to a beamer. The video comes via Airport/WLAN /LAN.
Make the USB Plug useful to connect printers or storage devices!!!
That should be great and makes Apple TV the most useful device ton install it in every room in the house!!!
I think, if the Apple TV can be connected to any kind of device, it shouldn't be Apple's hobby anymore.
Regards,
Michael

send your suggestions to Apple via _*Apple TV Feedback*_.
JGG

N95 access points

On my n95 i have set-up defined access points, my home router, other wlan routers, and my t-mobile internet. When i open applications that require an access point connection, not all of my access points will show up when propmted to select one. In other words, if i open internet radio, worldmate, nokia search all of my access points are shown to select from. If i open yahoo go, opera mini, em tube, none of my wlan access points are an option, only the t-mobile access point. Is there something in the settings that i'm missing? Thanks for any help given.

Hi n95tim
Is this a network branded or SIM free version of N95?
Happy to have helped forum in a small way with a Support Ratio = 37.0

MFP Anomaly Detected Access Points are moving from one wlc to another and vice versa

Hi together,
a customer has lost some Access Points to another WLC with 7.2 and then they come back after 15 minutes to the origin WLC with 7.5
Attached the messages
MFP Protection is configured as optional
152
Wed Nov 27 05:33:26 2013
MFP Anomaly Detected - 1 Not encrypted event(s) found as   violated by the radio 58:bf:ea:0f:67:4a and detected by the dot11 interface   at slot 1 of AP 58:bf:ea:0f:67:40 in 300 seconds when observing . Client's   last source mac 70:11:24:e4:43:0f
153
Wed Nov 27 05:31:40 2013
AP Disassociated. Base Radio MAC:88:43:e1:56:91:d0
154
Wed Nov 27 05:31:40 2013
AP's Interface:0(802.11b) Operation State Down: Base Radio   MAC:88:43:e1:56:91:d0 Cause=New Discovery Status:NA
155
Wed Nov 27 05:31:33 2013
AP Disassociated. Base Radio MAC:58:bf:ea:0f:73:d0
156
Wed Nov 27 05:31:33 2013
AP's Interface:1(802.11a) Operation State Down: Base Radio   MAC:58:bf:ea:0f:73:d0 Cause=New Discovery Status:NA
157
Wed Nov 27 05:31:33 2013
AP's Interface:0(802.11b) Operation State Down: Base Radio   MAC:58:bf:ea:0f:73:d0 Cause=New Discovery Status:NA
158
Wed Nov 27 05:31:28 2013
AP Disassociated. Base Radio MAC:58:bf:ea:0f:fc:20
159
Wed Nov 27 05:31:28 2013
AP's Interface:1(802.11a) Operation State Down: Base Radio   MAC:58:bf:ea:0f:fc:20 Cause=New Discovery Status:NA
160
Wed Nov 27 05:31:28 2013
AP's Interface:0(802.11b) Operation State Down: Base Radio   MAC:58:bf:ea:0f:fc:20 Cause=New Discovery Status:NA
161
Wed Nov 27 05:31:17 2013
AP Disassociated. Base Radio MAC:b4:e9:b0:e4:02:20
162
Wed Nov 27 05:31:17 2013
AP's Interface:1(802.11a) Operation State Down: Base Radio   MAC:b4:e9:b0:e4:02:20 Cause=New Discovery Status:NA
163
Wed Nov 27 05:31:17 2013
AP's Interface:0(802.11b) Operation State Down: Base Radio   MAC:b4:e9:b0:e4:02:20 Cause=New Discovery Status:NA
164
Wed Nov 27 05:31:15 2013
AP Disassociated. Base Radio MAC:a4:18:75:eb:da:b0
165
Wed Nov 27 05:31:15 2013
AP's Interface:1(802.11a) Operation State Down: Base Radio   MAC:a4:18:75:eb:da:b0 Cause=New Discovery Status:NA
166
Wed Nov 27 05:31:15 2013
AP's Interface:0(802.11b) Operation State Down: Base Radio   MAC:a4:18:75:eb:da:b0 Cause=New Discovery Status:NA
167
Wed Nov 27 05:28:26 2013
MFP Anomaly Detected - 35 Not encrypted event(s) found as   violated by the radio d8:24:bd:2f:df:6f and detected by the dot11 interface   at slot 1 of AP d8:24:bd:2f:df:60 in 300 seconds when observing Deauth.   Client's last source mac 00:23:14:a7:e3:54
168
Wed Nov 27 05:23:26 2013
MFP Anomaly Detected - 23 Not encrypted event(s) found as   violated by the radio f8:4f:57:a5:40:b2 and detected by the dot11 interface   at slot 0 of AP f8:4f:57:a5:40:b0 in 300 seconds when observing . Client's   last source mac 44:4c:0c:ba:27:77
Don´t know at the moment how to handle it.
Regards
Alex

Hi lAlex,
Disable Client MFP under WLAN advanced tab & see if this still occur
Regards
Rasika
**** Pls rate all useful responses *****

WAP4410N Access point and 4404 WLAN Controller.

Hello to all,
I am planning to setup a new WLAN using WAP4410N Wireless N Access Point. Is it possible to manage the AP using 4404 WLAN controller ?
I need to buy arround 42 AP for covering the entire building.
Regards,
Aslam

leolaohoo
Could u please tell me which series can be used with 4404 WLANC ?
Also the AP Should support Bridging or Mesh.

Using n80 wlan on mixed mode n/g access point?

I have a d-link dgl-4500. I use it in mixed mode n/g. My computers can connect just fine.
If I want to get the n80 to connect, I have to first change the wireless channel to 11 and then change it to channel 1.
Then and only then will my n80 find the access point.
If I set my AP to G only, then the wlan fires right up.
I'm not an expert on wifi. Are there any advanced wifi settings I can change to help my n80 find the AP easier?
current settings:
2.4GHz mode
mixed n/g mode
2.412 CH. 1
auto transmission rate
20MHz channel width
visible SSID
beacon 100
RTS threshold 2346
fragmentation threshold 2346
DTIM 1
short GI yes
802.11b protection no
Those are my current settings.
Thanks for anyone who can help.

I have a d-link dgl-4500. I use it in mixed mode n/g. My computers can connect just fine.
If I want to get the n80 to connect, I have to first change the wireless channel to 11 and then change it to channel 1.
Then and only then will my n80 find the access point.
If I set my AP to G only, then the wlan fires right up.
I'm not an expert on wifi. Are there any advanced wifi settings I can change to help my n80 find the AP easier?
current settings:
2.4GHz mode
mixed n/g mode
2.412 CH. 1
auto transmission rate
20MHz channel width
visible SSID
beacon 100
RTS threshold 2346
fragmentation threshold 2346
DTIM 1
short GI yes
802.11b protection no
Those are my current settings.
Thanks for anyone who can help.

How can i add and configure a new AIR-LAP1142N-E-K9 Access Point to a AIR-WLC4402-12-K9 WLAN controller

How can i add and configure a new AIR-LAP1142N-E-K9 Access Point to a AIR-WLC4402-12-K9 WLAN controller

Thanks alot, that helped me .....
what about option 43..i am using one wlc and the switch where wlac and APs are connected is playing the role of dhcp server used by APs as there is a dhcp pool configured. please advise. will the command be
option 43 hex (f104xxxxxxxxxxxx) f104 adding to it the management ip address of the wlac in hexadecimal.
if the ip address is 192.168.10.5 then the command will be
option 43 hex f104c0a80a05
please correct me if i am wrong!!!!

Packet drop when clients moving from one Access point to another

HI All ,
I am new to wireless . I am using WS-SVC-WISM-1-K9 wism module and using 5 Access points . When my clients are moving from one access point to another we are getting packet drops .
Kindly anyone suggest me what all configuration i need to verify on the controller for Proper client roaming so that i can resolve my issues..
Please let me know in case of any explanations requiered .
Thanks in Advance !!!
Regards
Angus

For radius authenticated SSIDs, you need WPA2-aes or wpa1-tkip-CCKM. It depends on what the client supports.
For pre-shared key, any WPA should be decent enough for roaming speed.
If you're on WEP ... no comment.
If you covered the above point, check if it's not a coverage problem. If the 2 APs coverage zone are not overlapping there will be a hole where you don't have signal and logically will have packet drops.

T60 - WLAN regularly loses connection to access point

Hi,
my T60, Windows Vista with
ThinkPad 802.11a/b/g/n, 802.11b/g/n Wireless LAN Mini PCI Express Adapter
WLAN driver version 05 Nov 2007, v7.3.1.127
WPA authentification
regularly (i.e. once every 15 min) loses the connection to the access point for some seconds.
I already tried different access points, different encryption, different WLAN channels, but nothing helped.
So the cause seems to be the WLAN adapter of my T60 or the driver.
I am using the latest driver. As far as I remember, I did not experience this issue on Windows XP.
Does anyone have an idea how to solve this problem? It's quite annoying.
Thanks! Best regards,
Daniel

Hi lwoxen,We apologize about the inconveniences, but I would be glad to assist. One thing worth trying is changing the wireless channel on the Cisco WAP.To do this, just login to your U-verse gateway by going to http://192.168.1.254. From there you should see a list of all the devices connected, and you just want to choose the details on the Cisco AP. It should give you an IP Address. From there, type that IP address into your browser. It should ask you for a user name and password:User: ATTadminPass: 401!VENFrom there go to the wireless options and change the Control Channel option to one of the 4 channels. I would suggest trying 36.Let us know if that works. Also, I will be sending you a private message, so if you do have any further problems, you have a direct point of contact.

3502 access point will not connect to 4400 Series WLAN controller

I recently upgraded our controllers to the latest version 7 software, as I read this was one of the requirements to get them to connect. But I am not having any luck getting into a controller. Normally I plug them in to the network, they pop into the controller listed as something like AP5057.a844.xxxx and then I can finish configuring them, but a static IP on them, etc...
This is the first of this model AP I have tried to deploy, so I am wondering what is different with these. or what I might be missing in the default config in the WLAN controllers.
Niether of which are set to "Master" either.
Thanks in advance, Tandrist

Hi,
The 3500 as you mention are supported on code 7.0
To get the access point to join the WLC we have different options.
If the access points will be on the same subnet as the WLC then you just need to get the APs to get a valid IP address from the DHCP server and once they have an IP address they will join the WLC because they are on the same subnet as the WLC.
If the access points are on a different subnet then the WLC you will need to have a DHCP server configured to give the unit an IP address and use option 43 or DNS so that the APs can send the join request to the correct WLC on a different subnet.
Or if not configure the AP via the console port with the static IP address and WLC IP address.
Also make sure that you have the correct country code enable on the WLC, and that the APs you purchased are the ones to work in this country, because if not the AP will not join the WLC.
http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps10981/data_sheet_c78-594630.html

WLAN 4402 Access points hang or reboot

We are seeing a very strange issue in our WLAN setup. Our access points hang or reboot randomly. We have WLAN controller 4402 with 25 Cisco 1020 Access points. Our syslog server shows for some access points rebooted. While others just hang and then come back online after 10-15 minutes. We have similar code 3.2.78.0 running at other sites and everything seems to be stable, therefore we do not want to upgrade or install a new code. Any suggestions, or help will be highly appreciated by the experts.
Thank you
Ismail

The errors we saw were "[ERROR] spam_lrad.c 1840: AP 00:0b:85:66:77:88 associated. Last AP failure was due to Configuration changes, reason: did not get join response"
We called Cisco TAC, got the case escalated to the highest level possible, till we got hold of the actual developers of the code. Gave Cisco engineers the Sniffer packet information of the wlan controller and AP.
Finally Cisco engineer found a bug in the code 4.0.179.8 The bug will be fixed in the next release.
Thank you
regards,
Ismail

Access Point(s) - AIR-AP1231G-A-K9 and others - Spotty Connectivity ...

Hello,
We have eighteen Cisco Aironet wireless access points (most of them are AIR-AP1231G-A-K9 with 12.3(2)JA2 IOS loaded) across our campus which people have weird issues with connecting.
Everywhere, people can associate and get an IP address without any issues. However, they cannot maintain a reliable connection to systems either on our network or off. They will get a web page to load and then it drops them out. In addition, they cannot connect back again for random intervals of time. To make this even more bizarre is that for random intervals they maintain a solid connection until it kicks people out again.
The vlan itself (60 in the configuration file below) works without issue as we have devices plugged in directly to the vlan via a hardwired port and they are stable.
Below is the configuration file. Any reason why we would have this issue?
Thank you for your time.
Regards,
Christopher Koeber
!version 12.3no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname AP-6!enable secret {authentication information}enable password {authentication information}!username Cisco password {authentication information}username admin password {authentication information}ip subnet-zeroip domain name {Domain Information}!no aaa new-model!dot11 ssid (Secure) Staff/Faculty vlan 70 authentication open !dot11 ssid Public vlan 60 authentication open guest-mode!!!bridge irb!!interface Dot11Radio0 no ip address no ip route-cache ! ssid (Secure) Staff/Faculty ! ssid Public ! short-slot-time speed basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root no cdp enable!interface Dot11Radio0.60 encapsulation dot1Q 60 native no ip route-cache no cdp enable bridge-group 60 bridge-group 60 subscriber-loop-control bridge-group 60 block-unknown-source no bridge-group 60 source-learning no bridge-group 60 unicast-flooding bridge-group 60 spanning-disabled!interface Dot11Radio0.70 encapsulation dot1Q 70 no ip route-cache no cdp enable bridge-group 70 bridge-group 70 subscriber-loop-control bridge-group 70 block-unknown-source no bridge-group 70 source-learning no bridge-group 70 unicast-flooding bridge-group 70 spanning-disabled!interface FastEthernet0 no ip address no ip route-cache duplex auto speed auto!interface FastEthernet0.60 encapsulation dot1Q 60 native ip address 10.60.255.6 255.255.0.0 no ip route-cache bridge-group 60 no bridge-group 60 source-learning no bridge-group 60 unicast-flooding bridge-group 60 spanning-disabled!interface FastEthernet0.70 encapsulation dot1Q 70 ip address dhcp no ip route-cache bridge-group 70 no bridge-group 70 source-learning no bridge-group 70 unicast-flooding bridge-group 70 spanning-disabled!interface BVI1 ip address 10.60.255.6 255.255.0.0 no ip route-cache!ip default-gateway 10.60.0.1ip http serverno ip http secure-serverip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eagip radius source-interface BVI1 logging snmp-trap emergencieslogging snmp-trap alertslogging snmp-trap criticallogging snmp-trap errorslogging snmp-trap warnings!!!line con 0 transport preferred all transport output allline vty 0 4 login local transport preferred all transport input all transport output allline vty 5 15 login transport preferred all transport input all transport output all!end

Hi Christopher,
Couple of suggestions before moving forward:
1. I would first secure these WLANs with a least a pre-shared key if possible(WPA/WPA2). Let me know if you need information on how to do this.
2. Next, I would remove the 'short-slot-time' on the radio:
config terminal
interface do0
no short-slot-time
end
If your users continue to have issues, I would want more information on the types of clients in the environment as well as wireless adapter make/model/driver version.

Access Points and Destinations

Hi,
I love the destinations feature of the N8, and like the idea of it switching to WLAN automatically. However, when apps (some/most) need to go online, they still bring up the list of individual accesspoints and not the destinatinos!
What's the point then, although some apps (world traveler IIRC) brings up the destinations instead of individual accesspoints. Is there anything I can do about this?

it takes a bit of getting used to moving from the access point lists to the destinations list they use now.
a couple of points i would suggest that are useful is that
1 many applications will inherit the settings specified in the browser or the 'default' setting in the destinations menu
2 you can add destinations and copy access points to them, if say you want some things to use wifi and an internet cell access point in that order, but you want something else to only only the internet cell access point you can add it to a new destination.
3 some apps that bring up the destinations list allow you to select access points from the options menu.
There's no dignity in begging for kudos. Do it for the karma.

808 moving wlan access point

Similar Messages

Maybe you are looking for