[845 Series] 845 Ultra - 9 beeps, does not POST

With my computer running I plugged in a NEC 870 printer into my LPT port. The printer was off and not connected to an outlet, but my system froze. I restarted the computer, it started beeping and didn't POST. I then did a hard reset and it POSTed but froze again when it was starting up XP. I then unplugged the printer from the LPT port but it didn't make a difference I can no longer get it to POST it just gives me 9 beeps .
It's an AMI Bios and I looked up the beep code and got this: ROM checksum error - bad BIOS
I've tried clearing the CMOS; reseated the battery; removed all my pci cards and my video card but still get the same problem.
Could plugging my printer to the LPT port with the computer running have fried my motherboard??
It there anything else I can try.
Thanks

Normally it wouldn't do any harm, but I suppose there was a short somewhere in the loop.
If you disconnected it and reset your CMOS there probably isn't much to do about it.
I would not plug that printer into any other computers before you try it on some ancient P200MMX or something like that that you don't care about.

Similar Messages

  • Type com.sap.xss.ser.xssmenu.model.types.P_Pernr does not exist

    Hi there,
    same Thread I post in "Portal Developement". Now I try my luck in ths category...
    we implement ESS (ERP2004 with WebDynpros) in our testsystem, but we got an error and don´t know what to do...
    System Landscape:
    - mySAP Enterprise Portal 6.0 SP17
    - Java Application Server (excluding from HR)
    - mySAP ERP2004 HR-System
    The Connections from the portal runs to the Java-App-Server, not direct to the HR-System (HR-System has no Java Installation and our Customer don´t want a installation, because it could be a bad performance)
    We implement the Jco´s and fill out the usermapping. If we want to call the firstpage of the new ESS-Role we get this error.
    Can anyone help us? Do we need some installations?
    Best regards
    Christian
    Error
    500 Internal Server Error
    Web Dynpro Container/SAP J2EE Engine/6.40
    Failed to process request. Please contact your system administrator.
    Error Summary
    While processing the current request, an exception occured which could not be handled by the application or the framework.
    If the information contained on this page doesn't help you to find and correct the cause of the problem, please contact your system administrator. To facilitate analysis of the problem, keep a copy of this error page. Hint: Most browsers allow to select all content, copy it and then paste it into an empty document (e.g. email or simple text file).
    Root Cause
    The initial exception that caused the request to fail, was:
    com.sap.dictionary.runtime.DdException: Type com.sap.xss.ser.xssmenu.model.types.P_Pernr does not exist
    at com.sap.dictionary.types.mdi.util.ProviderUtil.createAbapTypeXmlMap(ProviderUtil.java:400)
    at com.sap.dictionary.runtime.mdi.DataProvider.createSimpleTypeFromAbapType(DataProvider.java:586)
    at com.sap.dictionary.runtime.mdi.DataProvider.getDataType(DataProvider.java:286)
    at com.sap.dictionary.runtime.DdDictionary.getDataType(DdDictionary.java:95)
    at com.sap.dictionary.runtime.DdBroker.getDataType(DdBroker.java:164)
    ... 54 more
    See full exception chain for details.
    System Environment
    Client
    Web Dynpro Client Type HTML Client
    User agent Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1; .NET CLR 1.1.4322; InfoPath.1; .NET CLR 2.0.50727)
    Version
    DOM version
    Client Type msie6
    Client Type Profile ie6
    ActiveX enabled
    Cookies enabled
    Frames enabled
    Java Applets enabled
    JavaScript enabled
    Tables enabled
    VB Script enabled
    Server
    Web Dynpro Runtime Vendor: SAP, Build ID: 6.4015.00.0000.20051123162612.0000 (release=630_VAL_REL, buildtime=2005-12-14:21:51:22[UTC], changelist=377533, host=PWDFM026)
    J2EE Engine No information available
    Java VM Classic VM, version:1.4.2, vendor: IBM Corporation
    Operating system AIX, version: 5.2, architecture: ppc64
    Other
    Session Locale de
    Time of Failure Thu Jan 11 16:14:11 GMT+00:00 2007 (Java Time: 1168532051021)
    Web Dynpro Code Generation Infos
    sap.com/pcui_gp~xssutils
    SapDictionaryGenerationCore 6.4018.00.0000.20060530191647.0000 (release=630_REL, buildtime=2006-09-20:21:03:45[UTC], changelist=405154, host=PWDFM027.wdf.sap.corp)
    SapDictionaryGenerationTemplates 6.4018.00.0000.20060530191647.0000 (release=630_REL, buildtime=2006-09-20:21:03:57[UTC], changelist=405154, host=PWDFM027.wdf.sap.corp)
    SapGenerationFrameworkCore 6.4015.00.0000.20050818152155.0000 (release=630_VAL_REL, buildtime=2005-11-24:21:18:08[UTC], changelist=363812, host=PWDFM026.wdf.sap.corp)
    SapIdeWebDynproCheckLayer 6.4018.00.0000.20060823112633.0000 (release=630_REL, buildtime=2006-09-20:21:14:40[UTC], changelist=415262, host=PWDFM027.wdf.sap.corp)
    SapMetamodelCommon 6.4018.00.0000.20060302125746.0000 (release=630_REL, buildtime=2006-09-20:20:56:46[UTC], changelist=392271, host=PWDFM027.wdf.sap.corp)
    SapMetamodelCore 6.4018.00.0000.20060302125746.0000 (release=630_REL, buildtime=2006-09-20:20:56:36[UTC], changelist=392271, host=PWDFM027.wdf.sap.corp)
    SapMetamodelDictionary 6.4018.00.0000.20060302125547.0000 (release=630_REL, buildtime=2006-09-20:21:00:39[UTC], changelist=392265, host=PWDFM027.wdf.sap.corp)
    SapMetamodelWebDynpro 6.4018.00.0000.20060823112248.0000 (release=630_REL, buildtime=2006-09-20:21:09:40[UTC], changelist=415252, host=PWDFM027.wdf.sap.corp)
    SapWebDynproGenerationCTemplates 6.4018.00.0000.20060915154217.0000 (release=630_REL, buildtime=2006-09-20:21:52:30[UTC], changelist=417774, host=PWDFM027)
    SapWebDynproGenerationCore 6.4018.00.0000.20060823112633.0000 (release=630_REL, buildtime=2006-09-20:21:15:10[UTC], changelist=415262, host=PWDFM027.wdf.sap.corp)
    SapWebDynproGenerationTemplates 6.4018.00.0000.20060915154217.0000 (release=630_REL, buildtime=2006-09-20:21:52:30[UTC], changelist=417774, host=PWDFM027)
    sap.com/tcwddispwda
    No information available
    sap.com/pcui_gp~xssfpm
    SapDictionaryGenerationCore 6.4018.00.0000.20060530191647.0000 (release=630_REL, buildtime=2006-09-20:21:03:45[UTC], changelist=405154, host=PWDFM027.wdf.sap.corp)
    SapDictionaryGenerationTemplates 6.4018.00.0000.20060530191647.0000 (release=630_REL, buildtime=2006-09-20:21:03:57[UTC], changelist=405154, host=PWDFM027.wdf.sap.corp)
    SapGenerationFrameworkCore 6.4015.00.0000.20050818152155.0000 (release=630_VAL_REL, buildtime=2005-11-24:21:18:08[UTC], changelist=363812, host=PWDFM026.wdf.sap.corp)
    SapIdeWebDynproCheckLayer 6.4018.00.0000.20060823112633.0000 (release=630_REL, buildtime=2006-09-20:21:14:40[UTC], changelist=415262, host=PWDFM027.wdf.sap.corp)
    SapMetamodelCommon 6.4018.00.0000.20060302125746.0000 (release=630_REL, buildtime=2006-09-20:20:56:46[UTC], changelist=392271, host=PWDFM027.wdf.sap.corp)
    SapMetamodelCore 6.4018.00.0000.20060302125746.0000 (release=630_REL, buildtime=2006-09-20:20:56:36[UTC], changelist=392271, host=PWDFM027.wdf.sap.corp)
    SapMetamodelDictionary 6.4018.00.0000.20060302125547.0000 (release=630_REL, buildtime=2006-09-20:21:00:39[UTC], changelist=392265, host=PWDFM027.wdf.sap.corp)
    SapMetamodelWebDynpro 6.4018.00.0000.20060823112248.0000 (release=630_REL, buildtime=2006-09-20:21:09:40[UTC], changelist=415252, host=PWDFM027.wdf.sap.corp)
    SapWebDynproGenerationCTemplates 6.4018.00.0000.20060915154217.0000 (release=630_REL, buildtime=2006-09-20:21:52:30[UTC], changelist=417774, host=PWDFM027)
    SapWebDynproGenerationCore 6.4018.00.0000.20060823112633.0000 (release=630_REL, buildtime=2006-09-20:21:15:10[UTC], changelist=415262, host=PWDFM027.wdf.sap.corp)
    SapWebDynproGenerationTemplates 6.4018.00.0000.20060915154217.0000 (release=630_REL, buildtime=2006-09-20:21:52:30[UTC], changelist=417774, host=PWDFM027)
    sap.com/tcwdcorecomp
    No information available
    Detailed Error Information
    Detailed Exception Chain
    com.sap.tc.webdynpro.services.exceptions.WDTypeNotFoundException: type com.sap.xss.ser.xssmenu.model.types.P_Pernr could not be loaded: com.sap.dictionary.runtime.DdException: Type com.sap.xss.ser.xssmenu.model.types.P_Pernr does not exist
    at com.sap.tc.webdynpro.services.datatypes.core.DataTypeBroker.getSimpleType(DataTypeBroker.java:250)
    at com.sap.tc.webdynpro.services.datatypes.core.DataTypeBroker.getDataType(DataTypeBroker.java:213)
    at com.sap.tc.webdynpro.progmodel.context.DataAttributeInfo.init(DataAttributeInfo.java:314)
    at com.sap.tc.webdynpro.progmodel.context.NodeInfo.initAttributes(NodeInfo.java:669)
    at com.sap.tc.webdynpro.progmodel.context.DataNodeInfo.doInit(DataNodeInfo.java:233)
    at com.sap.tc.webdynpro.progmodel.context.NodeInfo.init(NodeInfo.java:654)
    at com.sap.tc.webdynpro.progmodel.context.NodeInfo.init(NodeInfo.java:657)
    at com.sap.tc.webdynpro.progmodel.context.Context.init(Context.java:40)
    at com.sap.tc.webdynpro.progmodel.controller.Controller.init(Controller.java:199)
    at com.sap.tc.webdynpro.clientserver.cal.ClientComponent.init(ClientComponent.java:347)
    at com.sap.tc.webdynpro.clientserver.cal.ClientComponent.createComponent(ClientComponent.java:855)
    at com.sap.tc.webdynpro.clientserver.cal.ClientComponent.createComponent(ClientComponent.java:158)
    at com.sap.tc.webdynpro.progmodel.components.ComponentUsage.createComponentInternal(ComponentUsage.java:143)
    at com.sap.tc.webdynpro.progmodel.components.ComponentUsage.createComponent(ComponentUsage.java:135)
    at com.sap.pcuigp.xssfpm.wd.FPMComponent$ComponentUsageManager.createBLCComponentUsage(FPMComponent.java:628)
    at com.sap.pcuigp.xssfpm.wd.FPMComponent$FPM.attachComponentToUsage(FPMComponent.java:773)
    at com.sap.xss.ser.xssmenu.vc.header.VcXssMenuHeader.onInit(VcXssMenuHeader.java:196)
    at com.sap.xss.ser.xssmenu.vc.header.wdp.InternalVcXssMenuHeader.onInit(InternalVcXssMenuHeader.java:225)
    at com.sap.xss.ser.xssmenu.vc.header.VcXssMenuHeaderInterface.onInit(VcXssMenuHeaderInterface.java:162)
    at com.sap.xss.ser.xssmenu.vc.header.wdp.InternalVcXssMenuHeaderInterface.onInit(InternalVcXssMenuHeaderInterface.java:144)
    at com.sap.xss.ser.xssmenu.vc.header.wdp.InternalVcXssMenuHeaderInterface$External.onInit(InternalVcXssMenuHeaderInterface.java:220)
    at com.sap.pcuigp.xssfpm.wd.FPMComponent.doProcessEvent(FPMComponent.java:466)
    at com.sap.pcuigp.xssfpm.wd.FPMComponent.doEventLoop(FPMComponent.java:354)
    at com.sap.pcuigp.xssfpm.wd.FPMComponent.wdDoInit(FPMComponent.java:179)
    at com.sap.pcuigp.xssfpm.wd.wdp.InternalFPMComponent.wdDoInit(InternalFPMComponent.java:110)
    at com.sap.tc.webdynpro.progmodel.generation.DelegatingComponent.doInit(DelegatingComponent.java:95)
    at com.sap.tc.webdynpro.progmodel.controller.Controller.initController(Controller.java:215)
    at com.sap.tc.webdynpro.progmodel.controller.Controller.init(Controller.java:200)
    at com.sap.tc.webdynpro.clientserver.cal.ClientComponent.init(ClientComponent.java:347)
    at com.sap.tc.webdynpro.clientserver.cal.ClientApplication.init(ClientApplication.java:370)
    at com.sap.tc.webdynpro.clientserver.task.WebDynproMainTask.execute(WebDynproMainTask.java:608)
    at com.sap.tc.webdynpro.clientserver.cal.AbstractClient.executeTasks(AbstractClient.java:59)
    at com.sap.tc.webdynpro.clientserver.cal.ClientManager.doProcessing(ClientManager.java:248)
    at com.sap.tc.webdynpro.serverimpl.defaultimpl.DispatcherServlet.doWebDynproProcessing(DispatcherServlet.java:154)
    at com.sap.tc.webdynpro.serverimpl.defaultimpl.DispatcherServlet.doContent(DispatcherServlet.java:116)
    at com.sap.tc.webdynpro.serverimpl.defaultimpl.DispatcherServlet.doPost(DispatcherServlet.java:55)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:760)
    at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
    at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.runServlet(HttpHandlerImpl.java:390)
    at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.handleRequest(HttpHandlerImpl.java:264)
    at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:347)
    at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:325)
    at com.sap.engine.services.httpserver.server.RequestAnalizer.invokeWebContainer(RequestAnalizer.java:887)
    at com.sap.engine.services.httpserver.server.RequestAnalizer.handle(RequestAnalizer.java:241)
    at com.sap.engine.services.httpserver.server.Client.handle(Client.java:92)
    at com.sap.engine.services.httpserver.server.Processor.request(Processor.java:148)
    at com.sap.engine.core.service630.context.cluster.session.ApplicationSessionMessageListener.process(ApplicationSessionMessageListener.java:33)
    at com.sap.engine.core.cluster.impl6.session.MessageRunner.run(MessageRunner.java:41)
    at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java(Compiled Code))
    at java.security.AccessController.doPrivileged1(Native Method)
    at java.security.AccessController.doPrivileged(AccessController.java(Compiled Code))
    at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java(Compiled Code))
    at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java(Compiled Code))
    Caused by: com.sap.dictionary.runtime.DdException: Type com.sap.xss.ser.xssmenu.model.types.P_Pernr does not exist
    at com.sap.dictionary.types.mdi.util.ProviderUtil.createAbapTypeXmlMap(ProviderUtil.java:400)
    at com.sap.dictionary.runtime.mdi.DataProvider.createSimpleTypeFromAbapType(DataProvider.java:586)
    at com.sap.dictionary.runtime.mdi.DataProvider.getDataType(DataProvider.java:286)
    at com.sap.dictionary.runtime.DdDictionary.getDataType(DdDictionary.java:95)
    at com.sap.dictionary.runtime.DdBroker.getDataType(DdBroker.java:164)
    at com.sap.dictionary.runtime.DdBroker.getSimpleType(DdBroker.java:170)
    at com.sap.tc.webdynpro.services.datatypes.core.DataTypeBroker.getSimpleType(DataTypeBroker.java:242)
    ... 52 more

    Hi,
    uhm... good question, long time ago...
    Error should be in the JCO-Destinations, where you can choose a targetsystem for each Jco-Destination.
    Since them we installed a java on the abap-system, so we have a doublestack.
    In the Jco Destiantions must be the ABAP-System.
    Application via SAPTicket and MetaData via fix User like DDIC.
    Regards
    Christian

  • HP MS218 Not Booting - Does not POST - Cannot reach BIOS

    Hello,
    I have an MS218 (product number: BR372AA #ABA) that I have been having issues with. It used to work fine (ran on WinXP), but currently will not even boot properly at all. No software or hardware changes were made to cause this problem to begin occurring, it simply just started happening one day when I went to turn the computer back on. The issue that I am currently experiencing is as follows:
    - Power stays on, but nothing is ever displayed on the screen
    - Does not post, cannot reach BIOS
    - Acts almost as if it is resetting itself constantly, the fan in the back will start to spin for a second or two, then stop, then start again, and repeat indefinitely until I unplug the power adapter.
    I initially figured it was a hardware issue, likely the motherboard, and began to troubleshoot the problem. As I removed non-vital components, the problem would persist. For instance, it happens regardless of external things (keyboard, mouse, etc.) being plugged in, or regardless of the hard drive or optical drive being plugged in. It still appears to happen in the absense of memory, however, I will instead hear beep codes (likely telling me that I don't have any RAM in). Ultimately, I decided to order a replacement motherboard, which recently arrived. Upon replacing the motherboard, the exact same problems happen, which leads me to believe that the motherboard was somehow not the culprit. I have also tried multiple power adapters to no avail, as well as resetting the CMOS battery without any luck. I'm really at a loss for what to do from here, and am currently sitting on hold with HP tech support.
    Any advice is welcome. Thanks in advance for your time and assistance.

    Hello Jaycera,
    There are two more components that we haven't replaced or look at and I would approach them in the order listed.
    1. Power supply
    2. Processor
    It sounds like it's a power issue the computer is getting enough power to start booting up and then losing it. Thus anytime I hear a power issue the first thing I think of is a power supply issue.
    The other thing is it could be the processor. The computer starts booting, makes a call to the processor, fails, boots down, starts booting up, makes a call to the processor and here we are in a vicious cycle.
    It could just be the processor needing reseated. Take it out, put it back in and make sure it's in properly and no pins are bent, or the processor could be bad.
    If I have helped you in any way click the Kudos button to say Thanks.
    The community works together, click Accept as Solution on the post that solves your issue for other members of the community to benefit from the solution.
    - Friendship is magical.

  • K9N2 plat does not post

     I have been having multiple issues with my system and I later determined that it was the power supply. I replaced the PSU and I also got a new case in the process. I installed everything in the new case including the PSU. I turned it on to test the system before I put all the USB stuff and peripherals into the mobo and it works good, everything is normal, but once I hooked all my peripherals like my keyboard, mouse, monitor it completely stopped posting the little LEDs are all red and the speaker does not make a beep. I unhooked it all and the problem still persisted. Then i took out my GPU and tried to turn it on and still and the LEDs are red I took out the mobo out of the case took all but one stick of ram off the mobo and hooked it up to the PSU and still it does not post,  and the LEDs are still red. Can someone tell me how to fix this problem or do i need to get a new mobo all together?   

    Read the posting guide as Stu says and post your system specs.
    To start with clear the CMOS: >>Clear CMOS Guide<<

  • Work order to cost center settlement does not post to GL module (FI)

    Dear Expert,
    I find the Maintenance Work order to cost center settlement does not post to GL module (FI)?Also, the settlement cost element is primary element define in GL chart of account.
    When an maintenance order is settled with KO88 or KO8G the work order value posted cost center and  the value is display in cost center report but not post to GL module in FI.As I notice only good issue or receive to/from work order is posted in GL but not the settlement of work order.Why?
    Between, Kindly advise what are the report or T-code to view the maintenance order is done the settlement and what are the value is settle for maintenance work order?
    Kindly advice under what circumstance when maintenance work order to cost center settlement is posted to GL(FI module)?
    Please advice.
    Thank you.
    KH

    Hi Kiran,
    The error message clearly says that "Cost Center validity starts from 01.10.2014" i.e. in the future period.
    Change the cost center from period in the past date and try.
    BR, Srinivas Salpala

  • FSCM 9.0: COBOL Process GLPPPOST does not post Journal Entry correctly

    Folks,
    Hello. I am workin on FSCM 9.0 General Ledger module. "Edit Journal" is AE program that works correctly. But "Post Journal" is a COBOL program that does not works correctly.
    COBOL process GLPPPOST posts only debit accounts of a Journal entry into table PS_LEDGER but does not post credit accounts of a Journal Entry into table PS_LEDGER. When run the Ledger Report, the report has only column headers and has no data.
    Does FSCM 9.0 have a problem or COBOL process does not work correctly ? Can any folks help me ? Thanks.

    Folks,
    Hello. Thanks a lot for replying.
    I linked my Ledger Group RECORDING with my Business Unit BU01 using "Set Up Financials/Supply Chain > Business Unit Related > Ledgers For A Unit". Then linked UserID VP1 with BU01 in User Preference. I have checked all information about the 3 concepts (VP1, BU01 and RECORDING) and don't see anything wrong.
    I suspect the problem is in the Journal Line page because its Chartfileds belong to 2 SetID (SHARE and FEDRL) and 2 Business Unit (BU01 and BU02).
    When define Chartfields value using "Setup FSC > Common Definition > Design Chartfield > Define Value", I see Chartfields "Fund", "Class" and "Program" with SetID "FEDRL", and other Chartfields with SetID "SHARE". The 2 SetIDs are default in the system.
    Because one Business Unit (BU01) can link to only one SetID (SHARE), I create one more Business Unit BU02 and linked with SetID "FEDRL". Thus, when create a Journal entry using "General Ledger > Journal > Create Journal ", we type in Business Unit (BU01) and Ledger Group (RECORDING) in Header page, but in Line page, some of Chartfields link with SetID SHARE and BU01, and some of Chartfields link with SetID FEDRL and BU02. The journal entry indicates "Inter/Intra Unit Journal". When select "Edit Journal" and click "Process", the message comes up as follows:
    "Ledger Group RECORDING is not valid for Business Unit BU01. Ledger Group defined for this journal is not valid for the Business Unit BU01".
    My question is: That the Chartfields in Journal Line page link with 2 SetIDs and 2 Business Units causes the above error ? Can any folks help ? Thanks.

  • Deactivate a depreciation area (Real area but does not post)

    Hi Guys
    I want to deactivate a depreciation area.
    It is a real depreciation area but area does not post in GL.
    Is there any risk in deactivating the depreciation area in the asset class ? We do not want to use this area any more '
    Thanks

    Thanks Anil
    But my question is
    Should I only have  to deactivate the depreciation area in the asset class OAYZ ? In this case new asset won´t see this depreciation area , but old asset still show this depreciation area in AS03. It seems no issue with this approach.
    Someone has suggested me also to deactivate it in OABN (but this depreciation area did not post) If I untick ordinary depreciation field  in OABN when I go to the asset I have an error message:
    "You cannot manage ordinary depreciation in area 60
    Message no. AA656
    Diagnosis
    According to Customizing settings, ordinary depreciation cannot be managed in area 60. The posting being processed changes ordinary depreciation.
    Procedure
    Check the amount entered and the transaction type."
    So, what is the safety procedure just go to OAYZ (I think this is the right way) and unclick the field "deact" ?
    "Indicator: Depreciation area is deactivated
    Set this indicator if you want the depreciation area to be inactive in this asset class or asset (although it is defined in the chart of depreciation)."
    Any other suggestion ?
    Regards

  • After I upgraded to OS x 10.7.5 my Mail account does not post mail, how come?

    After I upgraded to OS x 10.7.5 my Mail account does not post mail, how come?

    No. Tried all that. Server finally says they don't understand what's happening so better if I just delete accounts and set them up again from scratch. Haven't done that yet in hopes someone in the Apple world will have found a solution.

  • System does not post after Bios Flash

    After using Live Update to flash my Bios to the new version, the computer does not POST. The Bios Flash was successful - it rebooted and started normally. When I tried to restart it the normal way, it will not boot. The fans run when the "power on" button is pressed but nothing more. I cleared the CMOS using the jumpers but the problem was not solved. Can any one help?
    Can some good Samaritan give me a step by step method to resolve this problem?

    I followed the link you provided and managed to resolved it:
    1) Removed one memory stick and floppy;
    2) Cleared CMOS and rebooted successfully;
    3) Inserted floppy and reverted to the previous BIOS;
    4) Inserted the other memory stick and brought system back to full power again.
    Thank you very much for your assistance. I am sure MSI is aware of the problem and will take steps to rectify it ASAP

  • FSCM 9.0: COBOL program does not post a Journal into Ledger correctly

    Folks,
    Hello. I am working on FSCM 9.0 General Ledger module. To FSCM 9.0, we need to compile COBOL by ourself.
    I downlaod and install "MS Visual Studio 2005 professional" and "Micro Focus Net Express 5.0". Then compile COBOL successfully. The executable files are copied to PS_HOME\CBLBINU.
    Editing Journal is working correctly as follows:
    General Ledger > Journal > Creare/Update Journal -> Add -> Line -> Edit Journal ->Process, Total amount comes up correctly and Journal status becomes "V". All debit accounts and Credit accounts are posted into Database PS_JRNL_LN table correctly.
    But posting Journal is not working correctly as follows:
    In Journal Line page, after select Post Journal -> Process, Journal status becomes "P". But when check Database table PS_Ledger using select * from PS_LEDGER, only Debit accounts of a journal are posted into PS_LEDGER table, all Credit accounts of a journal are not posted into PS_LEDGER.
    Because posting a journal into PS_LEDGER table only debit accounts and no credit accounts, all general reports, such as Trial balance, cannot be generated.
    Thus, my questions are:
    First, does COBOL program GLPPPOST.exe have a problem ? If yes, how to solve it ?
    Second, do I set up something incorrectly in General Ledger module and cause only Debit accounts of a journal are posted into PS_LEDGER table and not Credit accounts ?
    Thanks.

    Folks,
    Hello. The question is solved by myself. Thanks.

  • Is it possible to use a tax code in FB60 but which does not post any tax?

    Hello Gurus,
    Can you advise if it is possible to configure a tax code which can be selected in FB60. But we want this tax code not to post any tax value in SAP but simply to be allowed to be selected and populated in the doucment. In FTXP a tax code can be setup that does not need to have a tax rate % maintained against it or be linked to a GL account. However, this tax code cannot then be used in FB60 as the system asks that a rate is maintained and then that an account must be maintained.
    Can you advise if it is possible to maintain a tax code in such a way that it can be selected in FB60 but does not result in any tax posting to any tax account? We want it so that no value is posted, so even a 0% rate would not be good.
    Thanks for any ideas on this.
    Mart

    If you set up 0% tax code, system will NOT post any entry to GL account. You can use the tax code in FB60 & MIRO & PO too.
    thanx

  • BAPI_0036_CREATE does not post budget to Funds Management

    Hi,
    We are using BAPI_0036_CREATE to create budget for a grant and posting to FM. It is creating a document in GM in  'unreleased' status, but not posting to Funds Management.
    We are passing FM data in the function module, but for some reason its not posting to FM. The Grant doc type is 'Unreleased' and is in Award phase.
    Does anyone know how to create budget document in released status and posting to FM.
    Thanks.

    Hi Rob,
    This budget is related to Grants. First we are creating budget for Grant, and then release it to FM, where the budget will be created in FM. The release part is not working.. hence it is not creating budget in FM.
    Thanks.

  • F-28  does not  post  exchange difference automatically

    Hi
    I   have  following   scenario :
    1) Customer invoice   is  $  100     (  it  is   AED  368   )
    2) Payment received   in  AED    @ 3.7   ie  total   AED  370
    3) In   OB08   exchange rate is   1 $ =  AED 3.68.    So  exchange diff  is   AED  2   ie    $   0.54  (ie  AED   3.68 -3.70)
    But   entry for exc. diff     goes to   a different  deduction    account.   It  does not go to the  GL defined  in  OB09
    Pl   advise.
    Do  I  have to  do  some config  in  customer master.  Is  any  specific  selection to be done in F-28  screen.
    Thanks
    kamala

    Hi
    In  OBA1,  I   have   assigned  the  GL  700400  (  Gain / loss  P/L a/c )  to  the  customer  Reconciliation a/c  121000  .
    The  invoice  is  recored  in   foreign currency   AED.    But  in   Customer balance,  it is  showing in  transaction currency USD.
    In  F-28 ,  I  give  currency  AED and  the  rate is picked  from  OB09.   Now  I  do not  put any  rate in  the  screen,  though  I  receive  AED 370   instead of  AED  368 - invoice value.     The    excess of  AED  2  is  due to exc. rate diff  and  I want it to go to  Gain /loss  exc diff A/c.
    I   TRIED   GIVING THE EXC RATE IN F-28  (  diff  from  one in OB08) and get  foll  entry. 
    001 40       0000113002 Conc Act - Wires In         3,710.00
    002 50       0000440000 Unallowed Deduction            10.00-
    003 15       0000123456 testks                      3,700.00-
    004 40       0000700400 G/L FC  Difference             0.00
    WHY IS  G/L   showing  ' 0.00' amount.
    Thanks
    kamala

  • I Cal does not post date chosen by point and click of the mouse.

    My ICAL mini calendar on the left is not posting the date that I click using my mouse. For example, if I click on June 27, 2008 on the mini calendar on the lower left corner, my large full day event calendar will post June 26, 2008. Tried doing a reset of all sync and calendar data from DOTMAC but it will still do that. What else anyone thinks I can do.
    Message was edited by: aldrinv

    There are some real sharp gurus in the iCal forum area:
    http://discussions.apple.com/forum.jspa?forumID=903

  • VCore over 1.550 + 10% does not post to end; Winchester and Corecenter voltage issues

    I can't get vcore more than 1.64 using my winchester. It does not help to use for example 1.500 + 15% either. I've tried 1.36b and 1.41mod bioses. With corecenter I can use vcore up to 1.800 just fine. Temperature of the water or of the case has no effect.
    Now I''m stuck with 1.65 (changes btw 1.63-1.65 in bios and Speedfan) when I use 1.550+10% (which should be 1.7 but it isn't).
    Is there some other program with which I could change vcore in windows except Corecenter? I could up fsb and vcore automatically during xp login. Corecenter is also a funny program as it ups the voltage upside down :D.. When I put + it lowers vcore and when - it ups it. So 0% gives 1.80 measured with Speed fan and it is quite stable.
    Perhaps a bios update will fix this or is there any other solution? I know that Winchesters only can get 1.7 from this board (but it isn't even that but ~1.64) but a program like Clockgen (which does not work with voltage on this board) would correct all problems.

    Quote
    Originally posted by Saulous
    Yes I said, would not be a problem with water cooling. I would attach two jpg pictures if I could but I don't have a place to put them and here I can't attach them. The first one would be a digicam shot showing the voltage in bios which is 1.63-5 when it should be 1.550x1.1=1.705 and the second one would be print screen shot which shows how the voltage in speedfan arises from 1.63-5 to ~1.8 when I set 0% arise with corecenter; lowering the % from 8.3 to 0; even if the voltage is set in the bios 1.550x10% . But who cares you can test it yourself, too.
    Man... I didn't realize a Winchester could take that much power!
    Rock on
    Edit - It really blows that you can't post images on this forum w/out having to host them elsewhere.

Maybe you are looking for

  • How can I scale just one dimension of a pic? I need to shrink the width only, to fit the frame.

    HELP!  How can I shink only one dimension?  I need to shrink the width slightly to fit the frame; the program only allows scaling that is proportional, so when I shrink the width the heigh becomes too short.  Father Mike

  • Not Possible to determine condition type- supplementry condition STO sch ag

    Dear All , While creating the stock transfer scheduling agreement in the transaction ME37, Stock transfer pricing schema is getting is picked up. where the standard condition type :P101 is being used for picking the Material valuation price of the su

  • [SOLVED] Why does my JAVA_HOME point to jre instead of jdk?

    I am having a strange phanomenon. I have jdk7-openjdk installed, but I still have % echo $JAVA_HOME /usr/lib/jvm/java-7-openjdk/jre This is only with my current user. When I try root or a freshly created user, I correctly get % echo $JAVA_HOME /usr/l

  • Detailed documentation of statistic-events?

    Hi experts, I'm looking for a detailed documentation and explaination of the statistic-events that can be found in the BEx-statistic-workbook. Especially I'm interested in the event "Bytes transfered" which can be subdivided refering to the objects "

  • Upgrading from cs to cs 5 or 6

    I have a really old version of Photoshop on my old computer. Just got a spankin new Mac and tried moving the CS over; no go. So I have to upgrade. I really don't want to purchase a brand new full version as it is so very expensive. Anyway around this