[845 Series] Adding 1gb of Ram to the MSI 6507 MB.

I have just attempted to add 1gb of ram (PC2100 DDR 266MHz CL2.5) to my MS6507 MB. When I go to power up my system nothing happens, the system only starts working again when I remove the new stick of ram. I have a 512mb stick in the other slot.
I have checked and the MB supports up to 2GB of ram. Any ideas why this is not being picked up??

I have tried the 1gb stick in both slots. SPD is set in the bios, I had previously been using 512 and 256 sticks in the two slots. Basically trying to find out if I have been sold a faulty stick of ram or if its not compatible with my MB (MS-6507). I have checked the MB spec and it says it can take up to 2GB of ram so am pretty sure that compatibility is not the issue??

Similar Messages

Questions after adding 1GB of RAM

I just installed 1GB of RAM, and I have 2 problems/questions.
1. The new RAM is not showing up in the "About this Mac". However, my iMac is running noticeably faster. Do I need to to something to correct this?
2. Also, since adding the RAM, there is no startup tone. I have checked the volume and restarted the computer several times with no change.
Are the two situations connected? Any suggestions?

I just found the solution/answer to both issues, and it was an easy one. To be sure that I had a proper connection between the RAM and the computer, I removed the RAM and reinstalled it.
Problem solved!

Does adding third party ram void the warranty?

Will adding third party RAM, like Crucial, void the original Apple warranty or Apple Care warranty extension? Does the latency rate matter? Am adding a second stick of 512 mb ram to new iMac G5 (rev B actually). Is this ram ok for my iMac rev B as a second stick?
"Crucial 512MB 184-Pin DDR SDRAM DDR 400 (PC 3200) Unbuffered System Memory Model CT6464Z40B"

Adding third-party RAM to your machine won't void the warranty unless you damage the machine during the installation. That module matches the specifications your iMac calls for.
(9216)

Cooler and RAM for the MSI P67A GD65?

I am thinking about getting the Thermaltake Frio for the MSI P67A GD65 board.
The ram i am thinking about is = G.Skill RipJawX 8GB (2x4GB) DDR3 PC3-12800C9 1600MHz.
Does anyone have the above components?
Does the cooler clear the ram?
Can anyone recommend some Ram and /or Cooler if the G.Skill is not suitable.
Cheers guys.

That Depends on how you set up the heatsink.
I happen to have this exact heatsink, but not the same RAM, I have Corsair. In order for me to use the heatsink, I had to put the fan at the rear of the motherboard (where the rear exhaust fan is) and not use the extra fan that came with it because it would block the RAM slots closest to the CPU. This caused me to switch the exhaust fan to an intake fan, which isn't a huge deal if you have top exhaust fans(i do). Be aware that if you have a sidefan/funnel/whatever over your cpu, you'll need to remove it as this heatsink stands a whopping 6.5(give or take .01in) inches tall.
see attached pics

[845 Series] Can the MSI 6507 support a 200GB hard drive?

If not can the BIOS be updated so that it can support a disk of this size?

use Win2k SP4 or WinXP SP1 then you're done.

Problems with PC3200 Ram on the K8T??

I'll soon be building a new Athlon64 (3200+) system around the MSI K8T Neo FIS2R board. Just waiting for my hard drives. I plan to install 2 Corsair CMX512-3200LLPT DDR400 DIMM modules. I've read several postings here from folks who claim to have trouble getting this ram to run at full speed on the K8T. I plan to set the CAS latency, TRCD, TRAS and TRP to manufacturers specifications and I don't plan to overclock the CPU or Ram. Anyone have experience with this ram on the MSI K8T? Can I expect to have issues? Thanks.
Andy

i am running the same memory at full speed and i am having ZERO problems with em. I have them in the two slots closest to the CPU, just so you know.

HT201364 I have most of the requirements for mavericks, however, can I still upgrade to mavericks with 1GB of ram??

I was wondering If I can upgrade to Mavericks if I have MOST of the requirements available..... The only thing I need to do is upgrade the ram. I currently have 1GB of Ram
Or MUST I upgrade the ram???????

And check the Mavericks requirements again. A MacBook that shipped with only 1 Gig of RAM is probably too old for use with Mavericks. As I believe that all of the qualifying MacBooks shipped with a minimum of 2 Gigs RAM.
The minimum requirement for the MocBook is:
MacBook (Late 2008 Aluminum, or Early 2009 or newer)
Note: It always helps to mention your exact Mac model when posting a question in the forums.

I have a MacBook 7,1 which i recently installed a PNY 250 SSD and added some RAM. The laptop was running awesome with OSX 10.6.8, lightning fast. Then I installed Yosemite. There was a bit of hang during the install, but Yosemite came up no issue

I have a MacBook 7,1 which i recently installed a PNY 250 SSD and added some RAM. The laptop was running awesome with OSX 10.6.8, lightning fast.
Then I installed Yosemite. There was a bit of hang during the install, but Yosemite came up no issue when I rebooted. Here is the problem:
Every other time I boot the MacBook it hangs at a grey screen with the prohibitory sign. Verbose reveals a "still waiting for root device" error. Now if I reboot from that hang, it boots fine, but then will hang again the next time. It keeps alternating like this. Any ideas??
I am not running any third party trim software, so that's not the issue.

I have a MacBook 7,1 which i recently installed a PNY 250 SSD and added some RAM. The laptop was running awesome with OSX 10.6.8, lightning fast.
Then I installed Yosemite. There was a bit of hang during the install, but Yosemite came up no issue when I rebooted. Here is the problem:
Every other time I boot the MacBook it hangs at a grey screen with the prohibitory sign. Verbose reveals a "still waiting for root device" error. Now if I reboot from that hang, it boots fine, but then will hang again the next time. It keeps alternating like this. Any ideas??
I am not running any third party trim software, so that's not the issue.

When I watch a streaming HD video the picture is jittery. Could adding RAM solve the problem?

When I watch a streaming HD video the picture is jittery. Could adding RAM solve the problem?

hello ozltem, i think this is related to this bug in adobe's flash plugin: https://bugbase.adobe.com/index.cfm?event=bug&id=3223393 (apparently they are aware of the issue & can replicate it, but they are not fixing it because it doesn't have a high priority).
as a workarounf you could try if [https://support.mozilla.org/en-US/kb/flash-113-crashes#w_solution-2-downgrade-to-flash-10-3 downgrading to flash 10.3] (which is still supported) or [http://forums.adobe.com/thread/1018071#TemporaryWorkaround disabling protected mode].

Is it ok to use 1GB + 256MB RAM in Satellite P25-s607

I have a Satellite P25-s607, and I wanted to know the following:
1) if it's ok to install only a single 1GB stick of RAM next to a 256MB stick? Will I lose any performance speed doing this versus 2 1GB sticks (assuming I use under 1GB of RAM at most times)? Sounds like it will not have a performance hit since this model doesn't support dual-channel memory (according to crucial.com)
2) I assume this is the correct (best) module to use: [1GB, 200-pin SODIMM, DDR PC2700|http://www.crucial.com/store/mpartspecs.aspx?mtbpoid=3B53A794A5CA7304] with specs:
# Module Size: 1GB
# Package: 200-pin SODIMM
# Feature: DDR PC2700
# Specs: DDR PC2700 CL=2.5 Unbuffered NON-ECC DDR333 2.5V 128Meg x 64
3) Is there any reason to install BIOS 2.10? It is listed under the toshiba support site under P25-S607-related, but the only change it states is: "Added support for the Pentium 4 D1 stepping CPU"
4) Is it possible to install a better CPU? I assume not...
5) What about graphics card (it came with NVIDIA® GeForce? FX Go5200 graphics controller; 64MB DDR external video memory)? Also I assume not...
Thanks for any help!!

Hi
Regarding the question number:
1) The notebook can be upgraded up to 2GB RAM and therefore you can use one 1GB RAM and one 256MB module. But its always better if you would use the identical memory modules. Its better for performance but I doubt you will notice an performance boost.
2) Yes, you have to use the 200-pin SODIMM, DDR PC2700 modules
3) If your notebook runs trouble free then I dont see any reasons for a BIOS update
4) Usually its not advisable to upgrade the CPU due to a higher heat dissipation and overheating risks due to a higher CPU performance
5) No, this is definitely not possible because the GPU is fixed on the board
Greets

[845 Series] MS-6507 - How to enable and configure On Board LAN

I have a very old Medion PC bought from PC World ages ago, which has MS 6507 Mother Board (256MB RAM, 1.7GHz...). It is still surviving and serving its purpose of net surfing chatting along with others. Till now it functioned as a standalone PC. I want to connect this PC to a LAN now. How can I do this? I found from the MS-6507 manual that there is an on board LAN connection? How do I enable it?
On the backside of my PC I do not find any RJ-45 jack connection, but I do have two USB ports.
Please respond and send me the answers quickly or else I may be conned / forced / compelled / mis-sold a LAN card worth some few bucks equivalent to buy few liters of pure alcohol for my Monday Morning tonic consumption. All thanks to the local broadband cable guy who belives he can sell that to me quicker then I can find the solution
Replies on this forum and at [email protected]

There are many series to the MSI 845 chipset and your mobo is an OEM mobo from MSI to Medion and Medion do reserved the rights to have modifications to the board as well as the BIOS.
I can't say much about Medion MSI OEM boards but for the retail versions of the MSI 845 chipsets, there are actually versions like "Standard" only whereby only the standard stuffs are available like USB, onboard sound, onboard VGA etc but for LAN 10/100Mbps, Firewire and RAIDs are all optional depending on the versions.
For now, I can only say that you may want to reach back to Medion's website and find out from their products list on your system specs.

Upgrading RAM in the somewhat anomalous1.33 Ghz Mac Mini

I have a 1.33 Ghz G4 Mac Mini that came with 512 MB RAM, and I'd like to upgrade the RAM to 1 GB. I haven't found any websites that specifically list this model of Mac Mini in their "find the RAM for your computer" search engines. According to my System Profiler, the pre-installed RAM is DDR SDRAM PC3200U-30330. So, I need to know exactly which RAM I should buy.
Thanks,
-Shawn
1.33 Ghz Mac Mini Mac OS X (10.4.6)

Welcome to the Apple discussion forums.
Sounds like you got one of the silent upgrade machines (mine is too). You'll want to read the Apple note on mini memory at http://docs.info.apple.com/article.html?artnum=300572
I upgraded my memory to 1GB, and used the Crucial (http://www.crucial.com) memory shown for the 1.42ghz mini, which is PC2700 memory. I did talk to someone at Crucial, and they said that the memory the the 1.42ghz mini used would work fine for the 1.5ghz mini, and they're right. Works like a charm, and passes all the memory tests I could throw at it. I also benchmarked it against other 1.5ghz 1gb mini's, and it's performance was on a par with them.
I would look at Crucial or Kingston (not valueram) memory, although Samsung and Hynix will probably work fine, too (you can scan the discussion forums for others memory experiences). Kingston shows the same RAM strip for either the 1.25ghz or 1.42ghz mini's.
If you're considering upgrading the memory yourself, two good sources on how to physically upgrade the ram are the OWC video at http://eshop.macsales.com/tech_center/index.cfm?page=Video/directory.html and a pictorial guide from ifixit at http://www.ifixit.com/Guide/82.13.0.html.

Suggestion in increasing the SGA and PGA after increase in the RAm of the machine .

Hi All,
Need an expert suggestion on the change's in the SGA and PGA of the oracle database after increasing the size of the machines RAM .
We have 64G of RAM in the machine .
There are 9 DB's running on oracle 10g and 11g on this machine
The total SGA of all the database's is around 18G .
DB1 has 2G of MAX_SGA_SIZE
DB2 has 8G of MAX_SGA_SIZE
DB3 has 1G   of MAX_SGA_SIZE
DB4 has 2G    of MAX_SGA_SIZE
DB5 has 676M   of MAX_SGA_SIZE
DB6   has 1.5G   of MAX_SGA_SIZE
DB7 has 1.2 G   of MAX_SGA_SIZE
DB8 has 675M   of MAX_SGA_SIZE
DB9 has 672 M   of MAX_SGA_SIZE
Now the machine RAM is up to 96G 64+ 32
what would be the suggestion on the increase in the SGA and PGA max size .
Any expert suggestion is highly apprciated .
Thanks in Advance

Thanks for this Justin.
Here the exercise is to add 4 CPU's and 32G RAM to the server earlier it was with 4 CPU's and 64G RAM this was decided by the server support team .
here is the stats from SAR   command ..
The platform is
Oracle Database 11g Enterprise Edition Release 11.2.0.2.0 - 64bit Production
PL/SQL Release 11.2.0.2.0 - Production
CORE    11.2.0.2.0      Production
TNS for Linux: Version 11.2.0.2.0 - Production
NLSRTL Version 11.2.0.2.0 - Production
04:00:01          CPU     %user     %nice   %system   %iowait    %steal     %idle
04:10:02          all     86.47      0.00     12.52      0.99      0.00      0.02
04:20:01          all     84.83      0.01     11.80      3.21      0.00      0.15
04:30:01          all     76.23      0.00     10.30     12.34      0.00      1.12
04:40:01          all     79.14      0.00     12.07      8.30      0.00      0.49
04:50:01          all     77.63      0.00     12.19      9.40      0.00      0.77
05:01:01          all     75.95      0.00     10.50     12.80      0.00      0.75
05:11:01          all     83.21      0.00     11.98      4.54      0.00      0.26
05:21:01          all     76.37      0.01     11.20     11.49      0.00      0.94
05:31:01          all     77.97      0.00      9.04     10.30      0.00      2.69
Average:          all     79.72      0.00     11.28      8.20      0.00      0.80
Now that the 4 CPU's and RAM is been added , my request is how to calculate the required kernal parameters for oracle to this new configuration for some improvement in the oracle performance .
like kernal.shmmax
      kernal.shmall
/dev/shm file system
largest value of MEMORY_MAX_TARGET or MEMORY_TARGET of all instances
the oracle is set as automatic memory management . it is not an RAC environment .
Any Expert suggestion is highly apprciated .
Thanks in advance .

Numerous attempts at a clean install of iTunes have failed. I am running Win7 64 bit on a Toshiba L series Satellite w/8G RAM and 100 G HDD space. Error message was (-42404), but following a complete (recommended) uninstall am now getting "Error 7".

Numerous attempts at a clean install of iTunes have failed. I am running Win7 64 bit on a Toshiba L series Satellite w/8G RAM and 100 G HDD space. Error message was (-42404), but following a complete (recommended) uninstall am now getting "Error 7". The prior uninstall included the establishment of administrator rights to files and folders left in the Apple folder after running the uninstaller, and successfully removing ALL visible and hidden Apple files and folders.
Any other suggestions out there folks?

On Oracle Metalink site, there are many documents which says that Oracle 32 bit software works on 32 bits OS and 64 bits software works on 64 bits OS. Official support is only in those combination....
So there is no good way to help you in your case-XE is 32 bit application with hard codded compiled libraries which most of them would not work on 64 bit OS.
Sorry
8(
Hope this helps

Programitically creating column series to flex chart not showing the chart

I want to create n number of series dynamically when i run my
application.
where n can be any value it depends on the data which i
retrieve from database. below i pasted the example
( in this example i have taken n = 4 i.e., CountMax=4 if i
change the CountMax=6 then it should generate 6series dynamically
after calculating the values. ). just copy the below code and paste
it in Flex builder and run the application.
in this example i am facing problem, chart series are not
showing. i dont know the reason why its not showing, if anyone got
the solutions for the problem please let me know. my actual
requirement is to retrieve data from Salesforce account and want to
populate the arraylist then display the chart.
<?xml version="1.0"?>

<mx:Application xmlns:mx="
http://www.adobe.com/2006/mxml"
creationComplete="drawChart()" layout="absolute">
<mx:Script>
<![CDATA[
import mx.controls.Alert;
import mx.charts.series.ColumnSeries;
import mx.charts.series.LineSeries;
import mx.collections.ArrayCollection;
[Bindable]
public var categoryArray:ArrayCollection = new
ArrayCollection();
[Bindable]
public var sArray:ArrayCollection = new ArrayCollection();
public function drawChart():void
var histMax:int = 25;
var histMin:int = 5;
var countMax:int = 6;
var tmpArr:Array = new Array();
categoryArray.removeAll();
for(var n:int = 0; n < 10; n++)
tmpArr[n] = histMin + Math.round((2 * n) / 20 * (histMax -
histMin));
categoryArray.addItem({data:tmpArr[n]});
// Add a series to the chart with the x-values and y-values
// from the arrays and set the series type to a column chart
for(var chartSeries:int = 0; chartSeries < countMax;
chartSeries++)
var tmpseries:Array = new Array(10);
for(var i:int = 1; i < 10; i++)
tmpseries = 3 * Math.random();
var cs:ColumnSeries = new ColumnSeries();
columnchart1.series.join( = [cs];
sArray.addItem({data:tmpseries});
//columnchart1.dataProvider = sArray;
cs = new ColumnSeries();
cs.dataProvider= sArray;
cs.displayName = 'Series';
cs.yField = 'data';
columnchart1.series[chartSeries] = cs;
]]>
</mx:Script>
<mx:Panel title="Dynamic Series Adding Sample"
width="195%" height="90%" layout="absolute">
<mx:ColumnChart id="columnchart1" height="338"
width="396" showDataTips="true" type="stacked" x="10" y="0">
<mx:horizontalAxis>
<mx:CategoryAxis dataProvider="{categoryArray}"
categoryField="data"/>
</mx:horizontalAxis>
<mx:verticalAxis>
<mx:LinearAxis baseAtZero="true" maximum="3"
autoAdjust="true"/>
</mx:verticalAxis>
</mx:ColumnChart>
</mx:Panel>
</mx:Application>

<?xml version="1.0"?>

<mx:Application xmlns:mx="
http://www.adobe.com/2006/mxml"
creationComplete="drawChart()" layout="absolute">
<mx:Script>
<![CDATA[
import mx.graphics.SolidColor;
import mx.charts.HitData;
import mx.controls.Alert;
import mx.charts.series.ColumnSeries;
import mx.charts.series.LineSeries;
import mx.collections.ArrayCollection;
[Bindable]
public var categoryArray:ArrayCollection = new
ArrayCollection();
public function drawChart():void
var histMax:int = 25;
var histMin:int = 5;
var countMax:int = 3;
var tmpArr:Array = new Array();
categoryArray.removeAll();
for(var n:int = 0; n < 10; n++)
tmpArr[n] = histMin + Math.round((2 * n) / 20 * (histMax -
histMin));
categoryArray.addItem({data:tmpArr[n]});
var cs:ColumnSeries = new ColumnSeries();
columnchart1.series = [cs];
// Add a series to the chart with the x-values and y-values
// from the arrays and set the series type to a column chart
for(var chartSeries:int = 0; chartSeries < countMax;
chartSeries++)
var tmpseries:Array = new Array(10);
for(var i:int = 0; i < 10; i++)
tmpseries
= 1 * Math.random();
if(tmpseries > 0.5)
tmpseries
= 1;
else
tmpseries = 0;
var testArrCol:ArrayCollection = new ArrayCollection();
for(var j:int =0; j < 10; j++)
var m:Number = tmpArr[j];
var m1:Number = tmpseries[j];
testArrCol.addItem({mData:m.toString(),nData:m1.toString()});
cs = new ColumnSeries();
cs.dataProvider = testArrCol;
cs.displayName = 'Series' + chartSeries;
cs.xField = 'mData';
cs.yField = 'nData';
columnchart1.series[chartSeries] = cs;
public function myTipFunction(hitData:HitData):String
return(ColumnSeries(hitData.element).displayName +" - "+
hitData.item.mData + "\n" + "Value : "+ hitData.item.nData);
]]>
</mx:Script>
<mx:Panel title="Dynamic Series Adding Sample" width="98%"
height="90%" layout="absolute">
<mx:ColumnChart id="columnchart1" height="338"
width="396" showDataTips="true" type="stacked" x="10" y="0"
dataTipFunction="{myTipFunction}">
<mx:horizontalAxis>
<mx:CategoryAxis dataProvider="{categoryArray}"
categoryField="data"/>
</mx:horizontalAxis>
<mx:verticalAxisRenderer>
<mx:AxisRenderer visible="false"/>
</mx:verticalAxisRenderer>
</mx:ColumnChart>
</mx:Panel>
</mx:Application>

[845 Series] Adding 1gb of Ram to the MSI 6507 MB.

Similar Messages

Maybe you are looking for