845e max error problems help!

Ok i have a computer with this board in it. and i have been getting a bunch of different errors the newest one is a big blue screen that comes up and says :
Problem has been detected and windows has shut down to prevent damage to your computer
it says either Page_fault_in_non_paged_area or
Irql_not_less_or_equal If this is the first time with the error reboot your computer and if it does it again follow the following steps:
Check to make sure any new hardware or software is properly installed if this is a new installation ask software administartor and check for windows updates.
If problem continues remove and newly installed hardware or software diable bios memory such as caching or shadowing. If you need to use safemode to disable or remove components reboot computer and push f8 and select advanced setup and safemode.
Technical Information:
*** STOP: 0x00000050 (0xc2a40fc8, 0xc2a40fc8, 0x00000000
Beginning dump of physical memory
Physical memory dump completed
Contact system administator for further assistance
And the only thing that i think is newly installed is a power supply that the shop i had this thing built at put in. The reason i brought it to the shop in the first place was because it was getting a techincal error and rebooting in games now it is getting this error in games and just online HELP THIS IS ANNOYING!!!
I have a pentium 4 2.4 ghz 80 gig hard drive with 8mb buffer 512 ram (I THINK ITS ONE STICK DONT KNOW) Geforce 4 Ti 4200 a 52x cd burner dvd combo dont know all the speeds and a 48x dvd drive help me!!!!!!!! thats all i know by the way

It is possible the new power supply isn't strong enough.
For starters try running memtest 86 on it for half an hour or so ( http://www.memtest86.com ).
From an internet search it seems this stop error can be related to many things to it's hard to poinpoint anything specific, but it is also possible it's software/driver related.

Similar Messages

  • Facetime Error Problem Help?

    I had my ipod restored and so when it restored i tried to put in my apple pass so i can activate my facetime and this is what it keeps saying to me. My inteernet works so i don`t understand why it is not working. How can I activate my facetime?

    I have the same issue too i tried going through support online providing them my serial number for my itouch and it was telling me that my itouch doesnt have any insurance and what not... i have been using facetime for months and the problem just occured last night... couldnt use my facetime or imessage... tried changing password and it still shows the same error...
    FACETIME ACTIVATION
    An error occured during activation. Try again.
    My Wifi works perfect and i could surf safari with no problem.
    HELP PLEASE!!

  • Pendulum Game Unidentified Error Problem - HELP PLEASE!

    Hi,
    I am trying to create a second level to my pendulum game. The idea is the ball moves left or right using arrow keys, and gets score. timed 1 minute, and if it hits the pendulum it loses. if it survives the first 60 seconds it goes to level 2 with the menacing pendulum, same idea only then the game ends. My go to and play code is not working using the button. Please help this is urgent...Download Link for zip folder with the files: http://www.mayscar.com/DMA205/D4%20-%20TEST.zip
    Thanks!
    Ksenia Zlotin
    Director of Development
    Scar Productions

    Please contact your ISP provided.. Another user of this unit under same company and same router ARRIS experience this issue, while theyre able to connect to other network and router.. Remember if your unit can detect and connect toother network besiide your arris router your issue is with your provider ISP. (Comcast asking the other user to pay $80.00 for activation where I am curious)

  • MSI 845E Max 2 RAID Help

    I have a Seagate baraccuda 40GB HDD. When i connect it to RAID, it dectect Functional but it give a warning like
    your HDD ATA66 or above will downgrade to ATA33 to prevent this goto BIOS setup #2 in DMA setup to configure it.
    in this situation, I don't know how to go ?(  Please help me.

    Ok,
    No.1 Are using an ata66 ide cable? (80 conductor)
    No.2 Go into the promise bios using ctrl+f and try to set the mode of the drive to ata66.(udma 4 I think??)
    No.3 ata66 may be disabled on the drive, you need to go to the Seagate site and download their utility to change it back ata66 mode.
    Hope this helps...

  • 845E Max (ms6566e) AGP help

    Im looking into buying the GeforeceFX 5900se 128mb. It only runs on AGP Version 2.0 but i cannot seem to find anywhere what AGP version it is.. ive never even heard of AGP versions unless their talking about 4x, 8x, etc.
    One AGP (Accelerated Graphics Port) 4x slot (1.5v only) is what it says about my boards AGP
    System Requirements:
       AGP 2.0 Compliant
    thats what the video cards manufactureres website says about the AGP

    Yea my board only supports agp4x and this card does 1-8 it seems.. i was just worried about that "agp version". ive got a 450w pow supply so i should be all set
    simbill

  • Help! Problems with 845E MAX HSF seating

     have a MSI 845E MAX and a P4 2.8 GHz cpu. I bought a coolmaster L71 for 478 socket type but when I put it on the cpu, the four little plastic white pins that hold the HSF mounting tray in place prevents the HSF from actually connecting with the CPU unless I use a load on paste (which is wrong)
    If I take out the pins the HSF sits on the CPU fine but surley this cannot be correct? Has anyone else had this problem or have any ideas why?
    I have also tried a mates P4 S478 HSF and it does the same, the four pins seem to stop it touching the cpu correctly.
    Party

    What's up? I got your Email - I don't know about cutting those pins off. Man, that really sucks those heatsinks aren't fitting correctly. What would be wrong with getting a stock Intel fan/heatsink? They are really cheap. I saw one for $7 shipped. Or get the f/h I have. It's a Coolermaster D14-7H53D. However, if you want to try and cut those pins go ahead because you can always buy a new bracket if it doesn't work. Let me know what happens. Good luck.
    Man, you can't say (s)ucks in this forum.  

  • Need MAJOR HELP recovering an 845E-Max board (no post)

    Hey guys and gals, I need some SERIOUS SERIOUS help here recovering my old board. I have an MSI 845E-MAX board, and decided to do some overclocking to it. While doing it, I raised the FSB too much, and now the system wont post. So I know what your all thinking, ok, take out your CMOS battery, or clear the JBAT1 jumpers. While ive done that, repeatedly, to no avail. Ive cleared the jumpers over and over, nothing. Taken the battery out for a 24hr period, nothing. Took the battery out for nearly a MONTH!, and nothing. Next your probally thinking, while maybe its bad RAM, Vid Card, CPU, etc. While it isnt lol Ive replaced/tested all the current hardware in other systems and they all work fine. Ive got a defenet mobo problem, and its really pissing me off lol on other boards by other manufacturers, if I put my FSB to high and it didnt post, restarting would put it into default specs, so I could adjust my fsb as needed. With this 845E though, its no such luck, and reseting the CMOS dosent do anything to fix it. Ive also read some posts about other boards who dont even have a JBAT1 jumper, and used an "insert" key method, where they power down, hold down the insert key, and boot up. Decided to try this, and it did nothing. I didnt think it was made for my board in the first place, but decided to give it a shot. IVe also tried reflashing/recovering the bios, by downloading the newest bios (its an AMI i believe) renaming it, putting it to a floppy, and booting the system holding CTRL+HOME to force the update. but it does nothing, and dosent even seem to read the floppy as the little green light dosent come on when i power up. The DVD/CD drive does though, and wehn i place WIN XP SP2 in the drive, it reads it and green light stays solid, so its just the floppy drive im having probs with I guess. Also, i get no beeps at startup, but can hear the hard drive boot and spin. I list my hardware specs below to help
    So PLEASE, some MSI guru, help me before I go crazy here! :P thanx a million to any one who can lend a hand.
    MSI 845E-MAX
    2 x 256 Azen RAM PC2100
    Benq DVD Burner
    Intel Pentium 1.5ghz P4
    Nvidia Geforce 64mb
    *this is a spare system im building, but the board WAS my primary board till I upgraded, so im use to its settings, just no OC'ing it apparently lol*

    I do indeed...and yah i get no beeps at all....
    but everything powers up fine...hdd spins...cd rom turns on, if i put in a Nic card, the green light comes when a cat5 cable is in it. So it looks like everything is receing power fine, but i just get no beeps at all to signify start up

  • I am not able to sync some videos and apps onto my iphone 3gs. it shows a sync error: 0xe8008001.i updated it but still i am getting the same sync error problem..please help.

    i am not able to sync some videos and apps onto my iphone 3gs. it shows a sync error: 0xe8008001.i updated it but still i am getting the same sync error problem..please help.
    aman

    Are you using Windows...?

  • HT201210 cont contact apple server error please help with ipad touch 4. im just fed up with apple please help me because why is it only apple with these kind of problems?

    cont contact apple server error please help with ipad touch 4. im just fed up with apple please help me because why is it only apple with these kind of problems?

    If you mean updae server
    Update Server
    Try:
    - Powering off and then back on your router.
    - iTunes for Windows: iTunes cannot contact the iPhone, iPad, or iPod software update server
    - Change the DNS to either Google's or Open DNS servers
    Public DNS — Google Developers
    OpenDNS IP Addresses
    - For one user uninstalling/reinstalling iTunes resolved the problem
    - Try on another computer/network
    - Wait if it is an Apple problem
    Otherwise what server are you talking about

  • Please Need Help!!!! (845e max bios setup)

    i bought all my computer parts seperataly.
    p4 1.7
    845e max
    radeon 9000 pro
    128 ddr
    Turning on the power for the first time the whole system worked fine (no operationg  system is installed yet). while i was seting up the ami bios, specifically in the PnP&PCI configuration, i came across the PLUG AND PLAY AWARE O/S (manual description: when set to yes bios will only initialize the PnP cards used for booting . the rest of the cards will initialized by the PnP operating system like 98, 2000 or ME. When set to NO, bios will initialize all the PnP cards. Select Yes if the operating system is plug and play aware.  all of a sudden the ami bios screen wasn't on my monitor. i rebooted and no ami bios setup.
    i have the led D-BRACKETS connected to my motherboard and all of them are in red colour. it says on the manual that it will show informaion regarding the the processor.
    anyway my cpu isn't busted  i know because i went back to the retailer i bought it from and they did a test for me which cost me $20.00 cdn and it worked fine.
    anyhow contact me if u have a suggestion
    email:[email protected]

    this mother board is jsut crapp there are alot of peopel having this problem i say replace it becsuae i got the same one over again and it died mabe i amjsut doing somethign wrong

  • MSI 6566E (845E Max)

    I have recently bought the MS-6566E m/b (845E Max). The problem I experience is strange :
    The 1st time I bought this m/b, it does not detect the HDD (IBM 25GP-352030 or Maxtor D740X-6L0402J. I went to the shop to get a new replacement.
    After installing the m/b again, I still encounter problem but with different case. This time, the m/b always reflect the HDD name incorrectly eg. Maxtor becomes haxtor, or the IBM become IHM etc.. it  continue to be that way.
    This does not end here, on occasion it only detect the Maxtor HDD size as only 5G instead of 40Gb. I did a low level, high leve format, clear the MBR but the problem still happen intermittently without much solution.
    On some occasion after formatting the HDD with eg. with Win98 system, when I boot up, I could not get the 'command prompt' as the system just hang there with only the cursor blinking at the top left of the screen.
    I did change my DDR 266Mhz RAM from Crucial to Transcend but does not help either.
    On the other hand, when I take the 2 HDDs and installed in another PC, it works perfectly ok. Able to see the HDD name correctly and no errors.
    The other funny thing is that, when I managed to get the m/b recognised the HDD, I can install any OS, eg. Win98SE, Win XP or Win2000, however after the completion of installation these OS, I can get th ?( e system
    booted up. The screen will show only the cursor blinking at the top left corner. Various means to get the HDD bootup fail.
    By the way, I have spent about 4 days without resolving the case. The funny thing is that, I'm not so sure even after replacing with another new m/b,
    Grateful for any one of your help.
    Thanks, mf  ?(  ?(

    Yes, I did change the IDE cable and dismantle and reinstall the m/b to the chassis.
    Strangely now that it seems that whenever I cool down the system, I can boot up (eg. Win98) startup boot menu selection, however when I select 'Normal'
    or 'Safe Mode', I will go into 'Fatal Exception 0D at 0147:xxxxxx' error. This always happen after I've cool
    down the system and reboot.
    If I dont let the system cool down, when I boot up, I get
    the same problem of blank screen and the cursor just stay at the top left corner awaiting for something ?
    Ytd, I did manage to get a spare P4 1.7Ghz CPU (478) and replace the exisiting one but the same problem appears as I have mention before.
    I do not suspect the HDD or FDD is having problem as both HDD can be install and configure with different2 OS when installed in another PC.
    I also did try to installed these HDD in this m/b after configuring it with Windows from other PC. However, the
    problem as describe above remains.
    So I have reassemble the m/b, change CPU, change the RAM type, swap the RAM slots, change VGA cards and HDD too. I have now taken 5 days to install this PC.
    Any other help... my friends, mf

  • 845E Max-L does not see 5 1/4 in. floppy drive

    My first 845E Max-L mb had no problems with my Teac FD-505 combo (3 1/2 in. + 5 1/4 in.) floppy drive. I was able to boot to DOS on the 3 1/2 in. drive and access the 5 1/4 in. drive normally. However, the first board developed a serious problem and was replaced by the vendor.
    The new board is unable to view the 5 1/4 in. drive when booted to DOS on the 3 1/2 in. drive. Both drives are correctly configured in the BIOS and both are visible on the CMOS summary page.
    When I boot into any O/S, both drives are visible in My Computer and both are accessible. However, if the PC is put into S3 standby (suspend-to-RAM) and then resumed, the 5 1/4 in. drive can no longer be accessed and Windows reports an I/O error.
    I removed the Teac combo drive, installed an individual 5 1/4 in. drive, configured it in the BIOS and it was duly identified on the CMOS screen. With a system disk in the drive, the system was booted. It went through a floppy seek, the floppy drive access light turned on, and then the floppy was ignored as the boot continued off the hard drive.
    I tried downgrading the MSI BIOS from ver. 5.7 to ver. 5.5, but that didn't eliminate the problem. (The BIOS was, of course, reset using the JBAT1 jumper.) I tried different floppy cables, to no avail.
    The Teac combo floppy and the single 5 1/4 in. drive work normally on another non-MSI mb.
    How can I get the 5 1/4 in. drive to work correctly and, once in Windows, after resuming from standby? Is use of 5 1/4 in. drives a known problem with this mb? If not, could the problem be due to a bad fd controller?

    Hi, Assaf.
    Thanks for your response.
    FOA, I no longer have the first board, so I don't know its PCB revision.
    As for the new board, how do I see its PCB revision? Is it on the board somewhere? If so, where?
    regards, Andy

  • 845E Max will not power on or boot

    I have an 845e Max(MS-6566E) and it will boot up once and run perfect until it is turned off and then it will not boot up again for some time.  when i say will not boot i mean no fans, no power, nothing.  I have tried several things, resetting the bios, changing the bios battery, different power supplies, even changed cases.  This board does not have anything to indicate it is getting any power like a LED so im not sure on that one.  Every once in a while when i turn the power supply back on i will see the fan jump.  Usually after i have pulled the power to the mobo and reconnected it.  Sometimes it will happen even when i connect the power to the mobo(the PS is ofcourse switched off at this point)  I cant think of anything else to try.  It runs fine once it boots up, reset works perfect.  its only when its turned off that it has the problems.  I got it to boot a few times today and thought i had fixed it by replacing the battery but now im having the same problem and have not gotten it to boot in the last two hours.  any help would be appreciated.
    845e Max
    Celeron 2.0ghz
    400w P/S(currently)
    256mb DDR

    Looking at the PSUs that you guys are using, I'm pretty surprised that the system is still running.
    Get a PSU with at least 400watts and 18A minimum on +12v rail.

  • Intel 845E Max Series Chipset Based

    Hi,
    i have few questions need to ask.
    i'm using Intel 845E Max Series Chipset Based (MS-6566E v1.0 ATX Mainboard)
    i want to know is that, is my this mainboard can support the harddisk which have 160gb of capacity?
    will it slow down my p4 1.7 speed if not support that high of capacity?
    what can i do in order to let this mainboard support it?
    what information u need to know to help me solve my problem?
    thanks.

    The worst case would be it only recognizes approximately 130 GB of it.  Check mobo manual for hard drive support.  also check for bios updates to add support.  Try partitioning it into 2 drives.  I know that works when OS is the limiting factor.  Not sure if that works when hardware is the limiting factor.  If you have not already bought the drive the safest answer is to buy a 120 GB drive.  The other solution is to purchase a PCI controller card that supports 160 GB drives (sometimes even packaged with the drive if you do not have the drive yet).

  • No audio on the 845E Max

    I just installed a Celeron 2.4GHz/845E Max combo, and got everything working except the embedded sound card.
    Then I figured out that I needed to install the drivers on the CD-ROM, so I did it.  After re-starting, the sound card was automatically detected and "Realtek AC'97 Audio" is installed.
    But it still doesn't work.  The volume control appears in the system tray, and when I check the properties of "Realtek AC'97 Audio", it just says "this device is working properly".
    But if I play an mp3 in winamp, the system hangs for a second and the mp3 never actually plays.  It just sticks at 0 seconds.  Same with "Sound Recorder".  Windows Media Player hangs for a while, then appears to be playing a mp3 or wav, but nothing comes out of the speakers.
    If anybody could help me, it would be greatly appreciated.  I don't want to have to buy another sound card if I already have one that can work.
    Thanks,
    Chad Handrich

    In the control panel under "Sounds and Multimedia", under the "Audio" tab, the preferred devices are:
    Sound Playback:  Realtek AC97 Audio
    Sound Recording:  Realtek AC97 Audio
    MIDI Music Playback:  Microsoft GS Wavetable SW Synth
    I don't get it.  I even turned hardware acceleration off in case that was causing the problem, and it still behaves in the same way.  
    If this helps, this is how I setup my system:
    1)  Formatted my C drive and installed Windows 2000
    2)  Used Windows Update to install every critial update and every recommended Windows 2000 update, including DirectX 9.
    3)  Went to the driver download section of the MSI website and installed "Onboard AC97 Codec Driver:  Support model  K7D Master (MS-6501):  Description  - AMD AC97 Codec Driver version 10B".  But that didn't do anything.
    4)  Realized I had a "Drivers and Utilities" CD, so I installed the drivers there and then Windows 2000 detected the AC97 Audio soundcard.
    5)  The control panel now shows that my soundcard is installed and working, but, as I said before, winamp and sound recorder hang for a second when I try to play a sound and don't actually play anything.  Windows Media Player hangs for a second, then looks like it's playing something, but no sound comes out.

Maybe you are looking for