845E Max-L does not see 5 1/4 in. floppy drive

My first 845E Max-L mb had no problems with my Teac FD-505 combo (3 1/2 in. + 5 1/4 in.) floppy drive. I was able to boot to DOS on the 3 1/2 in. drive and access the 5 1/4 in. drive normally. However, the first board developed a serious problem and was replaced by the vendor.
The new board is unable to view the 5 1/4 in. drive when booted to DOS on the 3 1/2 in. drive. Both drives are correctly configured in the BIOS and both are visible on the CMOS summary page.
When I boot into any O/S, both drives are visible in My Computer and both are accessible. However, if the PC is put into S3 standby (suspend-to-RAM) and then resumed, the 5 1/4 in. drive can no longer be accessed and Windows reports an I/O error.
I removed the Teac combo drive, installed an individual 5 1/4 in. drive, configured it in the BIOS and it was duly identified on the CMOS screen. With a system disk in the drive, the system was booted. It went through a floppy seek, the floppy drive access light turned on, and then the floppy was ignored as the boot continued off the hard drive.
I tried downgrading the MSI BIOS from ver. 5.7 to ver. 5.5, but that didn't eliminate the problem. (The BIOS was, of course, reset using the JBAT1 jumper.) I tried different floppy cables, to no avail.
The Teac combo floppy and the single 5 1/4 in. drive work normally on another non-MSI mb.
How can I get the 5 1/4 in. drive to work correctly and, once in Windows, after resuming from standby? Is use of 5 1/4 in. drives a known problem with this mb? If not, could the problem be due to a bad fd controller?

Hi, Assaf.
Thanks for your response.
FOA, I no longer have the first board, so I don't know its PCB revision.
As for the new board, how do I see its PCB revision? Is it on the board somewhere? If so, where?
regards, Andy

Similar Messages

IMovie does not see Aperture / iTunes library after hard drive restore

Hi all,
I recently exchanged the 320GB drive in my MacBook for a 500GB drive. I installed the 500GB drive and restored everything from my time machine backup. This went flawlessly and the MacBook works great, except for two issues:
1st: It did not read NTFS volumes anymore, I had to reinstall NTFS-3G - problem fixed.
2nd: I do not see my Aperture and iTunes libraries in iMovie '09 anymore. This worked great before.
Does anyone know how to fix this? Or what the problem could be?
Many thanks,
Michael

DaneelGiskard wrote:
.. restored everything from my time machine backup.
.. I do not see my Aperture and iTunes libraries in iMovie '09 anymore. ..
Does anyone know how to fix this? Or what the problem could be?
read about that problem frequently.. never got an answer, if the following usual advice fixes the problem:
• check permissions with Disk Utility
• check read/write rights of specific Folder AND files inside via Finder..

Toshiba Store.E TV+ 1TB does not see external WD My Book 3TB drive

Hi guys,
my Toshiba media player doesn't want to pickup my new portable HD drive.
I have a few drives, NTFS and FAT32, all work (from 1 to 2TB in sizes).
My newest drive is a WD My Book (3TB), and it doesn't want to pick it up.
Can it be that the firmware doesn't see the 3TB at all (meaning, supports it) ???

As I understand your issue, you have connected the WD My Book 3TB drive to the USB 2.0 port of the STOR.E TV+
Right?
The USB port supports plug n play so it should not be an firmware problem.
I guess the external drive requires too much power. The common USB 2.0 port provides 500mA power.
This is standard and if an external drive would require more power, the drive would not be recognized.

Extension manager does not see all of my adobe programs?? What can i do without reinstalling????

Hello i needed to install an extension for dreamweaver and for some reason extension manager does not see all my adobe programs. How can i fix that without reinstalling the programs?
Here are my Bridgetalk Diagnostics if it helps:
Result: BridgeTalk Diagnostics
Info:
Name = estoolkit-3.8
Status = PUMPING
Group = cs
Path = /Applications/Utilities/Adobe Utilities-CS6.localized/ExtendScript Toolkit CS6/ExtendScript Toolkit.app
Version = 2.0
Build = ES 4.2.12
Next serial number = 40
Logging: = OFF
Now = 12:58:04
Messages:
Message Version = 2.05
Authentication = ON
Digest = ON
Thread: estoolkit-3.8#thread
Avg. pump interval = 76ms
Last pump = 69ms ago
Ping: 7
ECHO_REQUEST: ECHO_RESPONSE
Timeout = undefined
Handler = undefined
STATUS: PUMPING
Timeout = undefined
Handler = undefined
MAIN: MAIN
Timeout = undefined
Handler = installed
LAUNCHED: LAUNCHED
Timeout = undefined
Handler = installed
DIAGNOSTICS: DIAGNOSTICS
Timeout = undefined
Handler = installed
INFO: INFO
Timeout = undefined
Handler = installed
SETUPTIME: thread=1ms, left=29ms
Timeout = undefined
Handler = undefined
Instances: 3
estoolkit-3.8#dbg:
msg[12:58:04]: 00000035
@BT>Version = 2.05
Target = estoolkit-3.8#dbg
Sender = estoolkit-3.8#dbg
Sender-ID = localhost:mac3334
Timeout = 12:58:05
Type = Ignore
Response-Request = Timeout
Headers = (no headers)
Timestamp = 12:58:04
Serial-Number = 35
Received = undefined
Result = undefined
Error = undefined
Body = (empty)
Incoming: 1
Outgoing: 0
Handler: 9
ExtendScript = for all messages
Error = for only msg #25
Error = for only msg #27
Error = for only msg #31
Result = for only msg #35
Error = for only msg #35
Timeout = for only msg #35
Result = for only msg #37
Error = for only msg #37
estoolkit-3.8#estk:
msg[12:58:04]: 00000037
@BT>Version = 2.05
Target = estoolkit-3.8#estk
Sender = estoolkit-3.8#dbg
Sender-ID = localhost:mac3334
Timeout = 13:08:04
Type = Debug
Response-Request = Result Error
Headers = (no headers)
Timestamp = 12:58:04
Serial-Number = 37
Received = undefined
Result = undefined
Error = undefined
Body: 107 bytes
Text = <get-properties engine="main" object="$.global" exclude="undefined,builtin,prototype" all="true" max="20"/>
Incoming: 1
Outgoing: 0
Handler: 1
ExtendScript = for all messages
estoolkit-3.8: (main)
Incoming: 0
Outgoing: 0
Handler: 1
ExtendScript = for all messages
Targets: 7
Connector = PCD
Installed: 0
Running: 0
fireworks-12.0:
Group = cs
Path = /Applications/Adobe Fireworks CS6/Adobe Fireworks CS6.app
Display Name = Adobe Fireworks CS6
MsgAuthentication = ON
MsgDigest = ON
ESTK = OFF
BundleID = com.adobe.Fireworks
Status = (not running)
ExeName = Adobe Fireworks CS6.app
aftereffects-11.0:
Group = cs
Path = /Applications/Adobe After Effects CS6/Adobe After Effects CS6.app
Display Name = Adobe After Effects CS6
MsgAuthentication = ON
MsgDigest = ON
ESTK = ON
BundleID = com.adobe.AfterEffects
Status = (not running)
ExeName = Adobe After Effects CS6.app
audition-5.0:
Group = cs
Path = /Applications/Adobe Audition CS6/Adobe Audition CS6.app
Display Name = Adobe Audition CS6
MsgAuthentication = ON
MsgDigest = ON
ESTK = ON
BundleID = com.adobe.Audition.5.0
Status = (not running)
ExeName = Adobe Audition CS6.app
bridge-5.064:
Group = cs
Path = /Applications/Adobe Bridge CS6/Adobe Bridge CS6.app
Display Name = Bridge CS6
MsgAuthentication = ON
MsgDigest = ON
ESTK = ON
BundleID = com.adobe.bridge5
Status = (not running)
ExeName = Adobe Bridge CS6.app
estoolkit-3.8: PUMPING
Group = cs
Path = /Applications/Utilities/Adobe Utilities-CS6.localized/ExtendScript Toolkit CS6/ExtendScript Toolkit.app
Display Name = ExtendScript Toolkit CS6
MsgAuthentication = ON
MsgDigest = ON
ESTK = ON
Status = PUMPING
Info:
Group = cs
Version = 2.0
Build = ES 4.2.12
Next serial number = 47
Logging: = OFF
Now = 12:58:04
Messages:
Message Version = 2.05
Authentication = ON
Digest = ON
Thread: estoolkit-3.8#thread
Avg. pump interval = 76ms
Last pump = 270ms ago
Ping: 7
ECHO_REQUEST: ECHO_RESPONSE
Timeout = undefined
Handler = undefined
STATUS: PUMPING
Timeout = undefined
Handler = undefined
MAIN: MAIN
Timeout = undefined
Handler = installed
LAUNCHED: LAUNCHED
Timeout = undefined
Handler = installed
DIAGNOSTICS: DIAGNOSTICS
Timeout = undefined
Handler = installed
INFO: INFO
Timeout = undefined
Handler = installed
SETUPTIME: thread=1ms, left=29ms
Timeout = undefined
Handler = undefined
ExeName = ExtendScript Toolkit.app
exman-6.0:
Group = cs
Path = /Applications/Adobe Extension Manager CS6/Adobe Extension Manager CS6.app
Display Name = Adobe Extension Manager CS6
MsgAuthentication = ON
MsgDigest = ON
ESTK = OFF
BundleID = com.adobe.exman
Status = (not running)
ExeName = Adobe Extension Manager CS6.app
switchboard-2.0:
Group = cs
Path = /Library/Application Support/Adobe/SwitchBoard/SwitchBoard.app
Display Name = SwitchBoard 2.0
MsgAuthentication = ON
MsgDigest = ON
ESTK = OFF
Status = (not running)
ExeName = SwitchBoard.app
Installed: 6
Running: 1
Groups: 119
cs3:
acrobat-8.0
aftereffects-8.0
soundbooth-1.0
bridge-2.0
contribute-4.5
devicecentral-1.0
dreamweaver-9.0
encore-3.0
estoolkit-2.0
fireworks-9.0
flash-9.0
illustrator-13.0
indesign-5.0
indesignserver-5.0
incopy-5.0
photoshop-10.0
premiere-3.0
stockphotos-1.5
audition-3.0
cs4:
acrobat-9.0
aftereffects-9.0
soundbooth-2.0
bridge-3.0
contribute-5.0
devicecentral-2.0
dreamweaver-10.0
encore-4.0
estoolkit-3.0
fireworks-10.0
flash-10.0
illustrator-14.0
indesign-6.0
indesignserver-6.0
incopy-6.0
photoshop-11.*
premierepro-4.0
audition-4.0
ame-1.0
exman-2.0
cs5:
acrobat-9.0
aftereffects-10.0
soundbooth-3.0
bridge-4.0
contribute-6.0
devicecentral-3.0
dreamweaver-11.0
encore-5.0
estoolkit-3.5
fireworks-11.0
flash-11.0
illustrator-15.0
indesign-7.0
indesignserver-7.0
incopy-7.0
photoshop-12.*
premierepro-5.0
audition-5.0
ame-2.0
exman-3.0
flashbuilder-4.0
flashcatalyst-1.0
ts1:
captivate3-en_us
captivate3-fr_fr
captivate3-it_it
captivate3-ja_jp
captivate3-es_es
captivate3-de_de
ts2:
captivate-4.0
el2:
captivate-5.0
as1:
acrobat-10.0
ts3:
robohelp-9.0
framemaker-10.0
cs55:
aftereffects-10.5
audition-4.0
bridge-4.1
contribute-6.1
devicecentral-3.5
dreamweaver-11.5
encore-5.1
estoolkit-3.6
fireworks-11.1
flash-11.5
illustrator-15.1
indesign-7.5
indesignserver-7.5
incopy-7.5
photoshop-55.*
premierepro-5.5
ame-2.5
exman-5.5
flashbuilder-4.5
flashcatalyst-1.5
switchboard-2.0
el25:
captivate-5.5
cs60:
aftereffects-11.0
audition-5.0
bridge-5.*
contribute-6.88
devicecentral-4.0
dreamweaver-12.0
encore-6.0
estoolkit-3.8
fireworks-12.0
flash-12.0
illustrator-16.*
indesign-8.0
indesignserver-8.0
incopy-8.0
photoshop-60.*
premierepro-6.0
ame-6.0
exman-6.0
flashbuilder-4.52
switchboard-2.0
prelude-1.0
speedgrade-6.0
el60:
captivate-60.*
ts4:
robohelp-10.0
framemaker-11.0

Same issue. Doesn't see Dreamweaver.

Notebook does not see mPCIe card (asm1061)

Aloha Community,
i am using an old notebook as a small server (cups/ftp/http/etc).
The Notebook is an old Dell Inspiron 1520.
I attached three 3,5'' HDDs to it which are powered via an external PSU.
the first HDD is connected to the original sata-port.
the other two are connected to a ASMedia ASM1061 Sata-controller. This controller sits on a small mPCIe card which i fitted on one of the three mPCIe slot the Notebook offers me (i tried all three).
In Bios all mPCIe-Slots are activated, still the OS does not see the HDDs.
also lspci seems not to see the card. Any ideas?
arne in ~/ > su arne
Passwort:
+ OS: Arch Linux x86_64
# Hostname: Yoshi
### Kernel Release: 3.19.0-gbdccc4e
##### Machine Hardware name: x86_64
###### Uptime: 0:26
; #####; Packages: 1257
+##.##### Processor Type: Intel(R) Core(TM)2 Duo CPU T7250 @ 2.00GHz
+########## Root: 572G / 917G (62%) (ext4)
###############+
.######; ;###;`".
#########. .########`
#' `#
[arne@Yoshi ~]$ lspci
00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c)
00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (primary) (rev 0c)
00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (secondary) (rev 0c)
00:1a.0 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 02)
00:1a.1 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 02)
00:1a.7 USB controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 02)
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02)
00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 (rev 02)
00:1d.0 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 02)
00:1d.1 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 02)
00:1d.2 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 02)
00:1d.7 USB controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f2)
00:1f.0 ISA bridge: Intel Corporation 82801HM (ICH8M) LPC Interface Controller (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 02)
00:1f.2 SATA controller: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) SATA Controller [AHCI mode] (rev 02)
00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02)
03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05)
03:01.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22)
03:01.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12)
03:01.3 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 12)
0c:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 02)
[arne@Yoshi ~]$
hope you guys can help me!
greetings
Last edited by arch-serv (2015-02-14 00:46:53)

that's the problem i guess... according to the bios settings all mPCIe slots are enabled, still the card does not show up.
arne in ~/ > lsblk
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
sda 8:0 0 931,5G 0 disk
├─sda1 8:1 0 1,9M 0 part
└─sda2 8:2 0 931,5G 0 part /
arne in ~/ > sudo dmesg | grep -i sata
[sudo] password for arne:
[ 0.511917] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x5 impl SATA mode
[ 0.524037] ata1: SATA max UDMA/133 abar m2048@0xfe9fb800 port 0xfe9fb900 irq 26
[ 0.524043] ata3: SATA max UDMA/133 abar m2048@0xfe9fb800 port 0xfe9fba00 irq 26
[ 0.843388] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 0.843416] ata3: SATA link down (SStatus 0 SControl 300)
arne in ~/ >
even without the correct drivers the card shoud show up in the output of lspci shouldn't it?
greetings

HT201269 itunes cannot see my iphone backup. I have a backup of the backup on an external HD, but even tech support cannot figure this one out. I copy and paste backups into the correct folder but itunes still does not see it. All I need are my contact

Sorry for short novel I am writing. I just wanted to cover as much backround as possible.
So, here it goes. I backed up my iphone 4 after renting a movie. The movie only played the starting credits before I was called on for daddy duty. A few days later the movie would not play, so I restored my phone from my backup. The movie would still would not play so itunes support refunded my purchase and ended my viewing privileges for that rental after verifying that I had not viewed the movie. I then had a problem with my contacts showing up twice in the contacts list after the restore. So I attempted another restore. All was well at this point. I then started having trouble with my pc and decided to copy the internal drive to an external source. A week later I had a system failure and did a factory restore on my computer. I re-installed itunes and tried to copy and paste the old backup into the new itunes. Now itunes just flat out does not see the backup file (I failed to mention that I did a factory reset on the iphone after the last backup, hopping to start fresh). Tech support had me uninstall and re-install itunes and then copy and paste the old backup into the newly installed itunes with no luck. The files are all there, but itunes just doesn't see them (itunes says the device has not been backed up to the cloud or to the local machine). We then tried backing up the factory restored iphone and replacing that restore file with one of my old backups on the external drive. Ok, this is where it gets weird. We replaced the guts of the folder but left the folder itself so itunes would continue to recognize the new backup folder with the old files. Whoohoo, itunes now see's a backup folder full of old files, or so we thought. The new files were deleted using shift delete so they would be gone for good and not mix with any files or folders. When I restore my phone, it restores the files that were deleted from the restore file (pause here for a moment and imagine the stupid look on the face of tech support and I while we silently wonder how files that were permanently deleted were restored). This left tech support and I both scratching our heads. My service issue was escalated to the next level. I waited for the phone call the next day that was scheduled at 10am to my wife's phone, but the call never came through. As usual, apple disappoints again. I just bought an iphone 5s and still have the iphone 4, and am looking for a solution to retrieve my contacts and restore to the 4 or 5s. I am guessing that files in other folders must be associated with the iphone backup in order for itunes to retrieve the files. Any ideas or support in retrieving my contacts would be greatly appreciated.

Sorry for short novel I am writing. I just wanted to cover as much backround as possible.
So, here it goes. I backed up my iphone 4 after renting a movie. The movie only played the starting credits before I was called on for daddy duty. A few days later the movie would not play, so I restored my phone from my backup. The movie would still would not play so itunes support refunded my purchase and ended my viewing privileges for that rental after verifying that I had not viewed the movie. I then had a problem with my contacts showing up twice in the contacts list after the restore. So I attempted another restore. All was well at this point. I then started having trouble with my pc and decided to copy the internal drive to an external source. A week later I had a system failure and did a factory restore on my computer. I re-installed itunes and tried to copy and paste the old backup into the new itunes. Now itunes just flat out does not see the backup file (I failed to mention that I did a factory reset on the iphone after the last backup, hopping to start fresh). Tech support had me uninstall and re-install itunes and then copy and paste the old backup into the newly installed itunes with no luck. The files are all there, but itunes just doesn't see them (itunes says the device has not been backed up to the cloud or to the local machine). We then tried backing up the factory restored iphone and replacing that restore file with one of my old backups on the external drive. Ok, this is where it gets weird. We replaced the guts of the folder but left the folder itself so itunes would continue to recognize the new backup folder with the old files. Whoohoo, itunes now see's a backup folder full of old files, or so we thought. The new files were deleted using shift delete so they would be gone for good and not mix with any files or folders. When I restore my phone, it restores the files that were deleted from the restore file (pause here for a moment and imagine the stupid look on the face of tech support and I while we silently wonder how files that were permanently deleted were restored). This left tech support and I both scratching our heads. My service issue was escalated to the next level. I waited for the phone call the next day that was scheduled at 10am to my wife's phone, but the call never came through. As usual, apple disappoints again. I just bought an iphone 5s and still have the iphone 4, and am looking for a solution to retrieve my contacts and restore to the 4 or 5s. I am guessing that files in other folders must be associated with the iphone backup in order for itunes to retrieve the files. Any ideas or support in retrieving my contacts would be greatly appreciated.

Logic does not see my hd omni as an input device. Any ideas? I've been told to reinstall logicpro - but apple won't let me because it says its already installed on this machine.

Logic does not see my hd omni as an input device. Any ideas? I've been told to reinstall logicpro - but apple won't let me because it says its already installed on this machine.

I'm having the same issue with a file called IMG_2353.MOV that was imported into iPhoto from my iPhone and also have to manually select the items to import (so the rogue file doesn't error everything out). I've tried using Image Capture to locate/delete the file directly from my iPhone, but even though I can SEE it in Image Capture, I can't delete it or anything. This is VERY frustrating! My friend/Apple guru's only suggestion was to backup my phone then restore it through iTunes. Risky but should do the trick. I'm too scared to try, though!

My computer does not see my printer

Hi: I am having a problem with my HP Photosmart 4500 printer. My computer does not see it. I have a USB connected to it, have uninstalled and installed the software two time, dowloaded the latest update and nothing. Add to that, I can not connect it by WIFI. WIFI on the printer is on but again, it's no where on any of the screens. The only variable I can think of that has changed has been the router I got recently from AT&T. Everything else works with the WIFI but no computer. I'm running 10.7.5. I have read the install instructions and nothing seems to be working. The one thing I do get from the HP install disc is a message reading the printer isn't recognized but there are no updates in support. OK, what am I missing here?

Try these steps to uninstall the current software using the HP scrubber and then reinstall using the current HP driver available through Apple.
To do so, perform the following steps:
1. Go to Applications/Hewlett Packard/ and then click on “HP Uninstaller”
2. Next click “Continue”
3. Highlight the device on the left pane.
4. Press and hold control+alt+command on the keyboard simultaneously while you click on “Uninstall”.
5. After you do this, you will see a pop up that asks you if you want to uninstall all HP software. Please note, that in doing this, it will remove any other HP printers that you also have installed.
6. Click “continue” and wait for the program to finish.
7. After it completes, reboot your computer.
Once the computer is back on, do the following steps:
WARNING: This is will delete all of your printers.
1. Go into “System Preferences” and then select either “Print & Scan” or "Print & Fax".
2. Right click (or control + click) on the rectangle listing your printers and then select “Reset Printing System”.
After you have reset the printing system, let's make sure you have the most recent HP driver package installed.
You can do this two ways. First, check for any available HP Update's by clicking the Apple icon and then Software Update. If there are any updates available, they should show up here. However, if the printer is connected by USB, it will not show any available updates. The other option is downloading the drivers from Apple's website.
You can download it here: http://support.apple.com/downloads/DL907/en_US/HPPrinterDrivers2.14.dmg
Once you have downloaded the driver package and completed the installation, you will want to plug your printer back in (if you were using a USB connection). After the printer is plugged back in, go into your print settings under System Preferences > Print & Scan. To add the printer, click the plus sign. You should see your printer listed here. If not, click "Add Printer or Scanner." Click the name of your printer and then click "Use:” box. Make sure that says the name of your printer and not AirPrint. If you are using the printer wirelessly, make sure that the printer "Kind:" is set to Bonjour or Bonjour Multifunction. Click "Add" down in the bottom right hand corner.
This will add your printer back using the most recent HP print driver available through Apple. Let me know if this helps resolve your issue or not. If it doesn't, let me know I will see what else I can do.
Best of luck,
Kyle

My mac does not see my printer

my mac does not see my printer

Is the printer physically connected to the computer with a cable, or is it wireless. Did you install the printer drivers from the manufacturers web site, for your specific OS?

My Ipad mini does not see my printer. my wife's ipad2 does. We both use IOS8 and upgraded at the same time. How can I remedy this?

My Ipad mini does not see my printer. my wife's ipad2 does. We both use IOS8 and upgraded at the same time. How can I remedy this?

OK great info!
I found 2 possible ethernet to USB adapters:
By "Plugable": USB 2.0 to ethernet LAN wired network adapter - seems this will work, but I'll contact Plugable.
2. Apple USB Ethernet Adapter
Easily connect your MacBook Air computer to an Ethernet network with the Apple USB Ethernet Adapter. Small and light, it connects to the USB 2.0 port of your MacBook Air and provides an RJ-45 connector that supports 10/100BASE-T performance. BUT NOT SURE IF THIS WILL WORK ON ANYTHING BUT a MacBook Air…
One person commented:
This little gem used to be the device of choice for adding a second Ethernet interface to a Mac Mini Server and I'd been using one that way for about a year. After doing a software update to 10.6.6 it stopped working. Forewarned is forearmed – it appears that Apple is finally enforcing the MacBook Air system requirement.
Thanks for any additional comments.
Best regards,
Steve Schulte
Sunday 6 January 2013

After upgrading to Mavericks my iMac does not see Sony camcorder in iMovie anymore. It still works on MacBook, so nothing wrong with camera or connections.

After upgrading to Mavericks my iMac does not see my Sony camcorder anymore. I tried the new iMovie as well as the old version 9.0.9, which is still in Applications. I checked the camcorder and connections in iMovie on my MacBook (not upgraded) and that still functions properly, so the problem does not seem to be in iMovie, old or new, or in camcorder and connection.
Anybody with the same problem or a solution?
Thanks mbkom

Try this

HT201302 I have a large video on my ipad that I would like to transfer to a computer. But my computer (using various software that came with Windows 7) does not see this video, although it sees all the other videos on my ipad. This video is too big to t

I have a large video on my ipad that I need to transfer to my PC (a window 7). I could also use a windows 8 if that would help. But all of the applications I have tried do not see this large video (52 mins) even though they transfer smaller videos fine. The ipad will not let me trim the video, saying it is too large. This is true even though I only want to trim the original, and not create a new video. (Actually it refuses before it gets to the choice of creating something new or just eliminating something from the original). I have been to an Apple store, but the people there only could recommend that I try some alternate applications to do the transfer (Kodak EasyShare). I don't have much faith this will work. I think I have this application on an old PC, and it is not something I want on my new computers.
Is it possibled the size of this video just violates the transfer formats for files over USB? If so, I will just delete the video and move on. But the video is really something I wanted to save. I would be happy to eliminate most of the video, but the ipad will not let me trim it.
I also tried to import the video with Windows Moviemaker (free with W7). It also does not see this file, but works fine on the other videos on the ipad.

How to Transfer Photos from an iPad to a Computer
http://www.wikihow.com/Transfer-Photos-from-an-iPad-to-a-Computer
Importing Personal Photos and videos from your iOS device to your computer.
http://support.apple.com/kb/HT4083
iTunes: Frequently asked questions about viewing and syncing videos
http://support.apple.com/kb/HT2729
Also check out the Photo Manager Pro app.
https://itunes.apple.com/us/app/photo-manager-pro/id393858562
 Cheers, Tom

Decided to update iphone 4 to ios 5.1 and mid update it froze and the screen is black. Phone does not respond to any combinations of home and power buttons, when plugged into computer it does not see it is plugged in, any ideas?

Decided to update iphone 4 to ios 5.1 and mid update it froze and the screen is black. Phone does not respond to any combinations of home and power buttons, when plugged into computer it does not see it is plugged in so I cannot restore or anything. Looks like the screen is on it's just unresponsive and black obviously. Has anyone had this problem? I was updating via wifi right in front of my router and my computer.

Spoke to a "senior advisor" in the Apple TV department. Her suggestions: change channel in router to minimize/eliminate wifi interference from other users; move router away from any metal - i.e., DVD player, phone modem, etc.; keep router away from wireless 2.4 gH phones, which are "notorious" for crashing wifi routers. So she confirms that the problem is one of connection to router suddenly dropping out.
My own feeling is that none of these fixes will do the trick, because it seems pretty clear that there is a hardware component here - the timing of the drops seems like an overheating issue. It takes 35-40 minutes for the box to warm up enough for the first drop; then each consecutive drop happens quicker than the one before, as it heats up more. Each time it drops, its tiny brain gets a little more scrambled; last night it finally wouldn't start up again at all.
My suggestion is that everyone who is experiencing this problem, please call Apple tech support and ask to speak to a senior advisor in the Apple TV department. Make them aware of this problem!

Itunes does not see ipod touch

Upgraded Itunes11.0.0.163 for Windows 7 64 bit. Running on Asus Laptop. Windows 7 Ultimate 64 bit.
Itunes does not recognize ipod toch Gen 4 updated to ios 6
Totally uninstalled and manually cleaned all itunes software several times.
Reset iPod touch offline several times.
Updated iPod touch driver.
WIndows ses the iPod as portable device, iTunes does not see it.
Any ideas on why I can't use iTunes with my touchi? Has anyone hadluck with non apple softyware, seems apple has made a mess of itunes on this version. I've been throught multiple threads on reinstalling and with tweaks. I've read the apple device is faulty in this latest version, any news on when this fault will be fixed? Love to hear from an Apple person on this. Samsung is looking more and more attractive.

See:
iOS: Device not recognized in iTunes for Windows
I would start with:
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7

I updated to iTunes 10.7 and now iTunes does not see my iPod Touch. It says the Apple Mobile Device USB Driver cannot be installed.

I updated to iTunes 10.7 and now iTunes does not see my iPod touch. After the update I got a message that the Apple Mobile Device USB Driver could not be installed. I have uninstalled and reinstalled iTunes 3 times, but still cannot fix the problem. I have followed the suggested fixes in Apple Support. Any suggestions? Thanks!

Try the actions here for that driver.
iOS: Device not recognized in iTunes for Windows
I would first do this:
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7

845E Max-L does not see 5 1/4 in. floppy drive

Similar Messages

Maybe you are looking for