848P Neo-LS RAM-memory ?

Hi  someone who ones where i can find witch ram memory i should have for my 848P neo-LS ??
I have Kingston 512 Pc3200 CL3   is that  ok ?
thanks
Henke L

http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_trp_detail.php?UID=493
The Memory Modules link on that page will give you the modules the board has been tested with. Others may work as well, but just haven't been tested.
I didn't check to see if the Kingston are in the tests, but they do work with other boards using the ICH5 chipset.

Similar Messages

  • CL3 Memory wont work on Intel 848P Neo Mainboard? any help?

    Hi,
    I purchased Kingston DDR Ram recently and put it into my computer. It worked fine but sometimes I start computer up and it comes up with a message saying something is wrong with the memory timings. I dont think it is configured properly.
    In the BIOS there was an option to "CONFIGURE DRAM TIMING BY SPD" and i set that on ENABLED. If i set it to DISABLED then there are other options that I have to set.
    These options are as follows:
    1. CAS# Latency [Options 2 or 2.5 Clocks];
    2. RAS# Precharge [Options 2, 3 or 4 Clocks];
    3. RAS# to CAS# Delay [Options 2, 3 or 4 Clocks];
    4. Precharge Delay [Options 5, 6, 7 or 8 Clocks];
    5. Burst Length [Options 4 or 8 Clocks].
    These are the 5 settings i can modify and in the "[]" brackets are the options i can select from for each one. Could you please tell me how I am to configure this in order for the memory to work. The Ram voltage is set at 2.6v. The CAS# Latency only allows 2 or 2.5 clocks so im not sure if thats the problem or not.
    The specifications of my computer as as follows:
    RAM - Kingston KVR400X64C3A/1G 1GB PC3200 CL3 184
    Motherboard - MSI 848P Neo (MS-6788 v1.0)
    Motherboard BIOS - A67991MS v1.0081203
    Motherboard firmware - V1.0 initial release
    CPU - Pentium 4 2.53Ghz
    Regardless of the settings I have done so far, if it works past POST and loads windows...after sometime it randomly resets. Any idea why this is the case? I suspect its the CAS Latency. The manual says you can select 3 Clocks but i dont see that option, just 2 or 2.5

    The Kingston Site is not always correct or to be more precise:  it does not state the operating conditions under which DDR-400 is possible on this mainboard.  In this cases the problem is not the modules as such (they are able to run @DDR-400) if they are put into a system that supports that.
    In your case the problem is the mainboard's chipset which can only make the memory run @DDR-400 when an FSB-200-MHz processor is installed.  You are currently using an FSB-133-MHz processor.  With such a processor, the maximum memory clock speed that the system can run at is DDR-333.  I just checked the Intel Datasheet for the 848P Chipset.  That is also the reason why all DDR-400 modules mentioned in the official MSI Memory Test List for this mainboard were tested with an FSB-200-MHz-CPU installed. 
    The only thing you can do to get aroung this "problem" is to install a supported FSB-200-MHz-processor.
    Quote
    Also, when i look at my motherboard manual, it shows option for 3 as CAS latency but in reality when i check the bios its not there (which im assumin is reason y it wont work).
    It would probably be there once a processor is installed that will enable higher memory clock speeds than DDR-333.  However, the actual CAS latency is only of secondary importance here.  The main question is why DDR-400 is not possible (which would automatically yield a CAS Latency of 3 by settings the values in the corresponding SPD Profile).  And as I said:  DDR-400 is only possible with an FSB-200-MHz-Processor.
    With your current configuration, the highest possible memory speed is DDR-333 @2.5-3-3-7.  In case that runs fine & stable everything is working as it should.

  • Problems with adding 1Gb memory to 848P Neo

    I have had an 848P Neo since February now, with only 512Mb, but seeming as some games and applications I have been running are now taking 512Mb as a minimum, I decided to buy another stick of 512Mb PC2700 333Mhz DDR to take me up to 1Gb. But I struck a problem.....  
    With both sticks of memory in the machine, the computer fails the memory 'POST' test on reboots (not boots from power off, but when something makes it reboot. ie: BIOS or WinXP). When I do get into Windows, the Core Centre utility acts weird too. It locks up the whole machine, whether you are trying to 'restore' it, or adjust the FSB. It won't even shut down or Ctrl-Alt-Del with it (this is surprising as I have never had to turn off or reset it via the case, as all lock ups have been recoverable).
    With either of the sticks in on their own, it works fine. eg: Stick 1 in DIMM 1 or 2/Stick 2 in DIMM 1 or 2. But when they both go in at the same time I get problems. Both sticks are of the same CL according to the Everest System utility.
    I have been getting help from my magazines forum, but they seem to have hit a dead-end too. Thread is here.  
    I would also like to add that I don't think it can be because one stick is Kingston (I think) and the other PNY, as I took the Kingston out of my second comp (same memory) and it still wouldn't work.  
    I hope I can get this fixed soon.  

    How do you up the 'VDIMM'? lol.
    I don't think it is a mixing prob, as I took the other stick from my other computer (all the numbers on the memory chips are exactly the same, except it is a green stick instead of blue), and the problem still existed.

  • 848P NEO-S - No POST, No Video, No Beep

    I have a 848P NEO-S motherboard with a 2.8Ghz P4 installed.  
    The system had been working fine for over a year until it mysteriously powered down.  Since then I have tried booting it back up with no success.  When I had both the main ATX & P4 ATX connected to the motherboard it would not power up at all.  With the P4 ATX plug disconnected the system will power up, but still there is no video, bleeping or POST, the only evidence of the system having any power to it is that the CPU and case fan come on.
    I have tried testing the system with all the drives removed and just the RAM, CPU and video card.  I have also tried with just one RAM module inserted and have also cleared the CMOS. I have tried testing with a brand new PSU and have reseated the CPU and also checked it for any physical damage but all of this was unsuccessful.
    On the D-Bracket it hangs on the testing base and extended memory lights.  This is also the only combination it performs.
    Any feedback would be greatly appriecated.

    Quote from: SR1000 on 12-January-05, 07:21:26
    I have a 848P NEO-S motherboard with a 2.8Ghz P4 installed.  
    [...]the only evidence of the system having any power to it is that the CPU and case fan come on.
    On the D-Bracket it hangs on the testing base and extended memory lights.  This is also the only combination it performs.
    Any feedback would be greatly appriecated.
    I have exactly the same problem. (Only difference is that i have a celeron 2.4 plugged into the board). Did you find a solution?

  • 848P Neo-LS [help configuring ...]

    I just set up a 848P Neo-LS
    support for:
    800mhz FSB
    400mhz DDR
    I installed a P4 2.8c which should be able to run at 800mhz
    I don't feel the mainboard manual give enough detail to explain how to set up the bios and when i view "CORECENTER" it shows my pc running at 200mhz FSB. and when i click where it shows this on the right pannel, what's with the 200mhz x 14.0=2807 mhz?
    I just want to make sure my pc is running at 800mhz FSB and my 400mhz pc3200 ram i have is running optimally as well.
    ALSO, in the bios it shows the DRAM, PSB 400MHZ, PSB533 MHZ AND PSB800MHZ.
    IF PSB is stands for another bus what bus is it and y do the equivalants to 400, 533 and 800 only = 100-344mhz, 133-500mhz and 200-500mhz respectively?
    ANY help would be appreciated, i know from viewing this forum that there are MANY of u out there that are EXPERTS with MSI boards and setting them up.
    thanks for any help
    IRISHHUNK
    (St.PAtricks day's commin up, have fun

    And PSB (Processor Speed on BUS) is Basically the same as FSB (Front side Bus) only it is a different Name, So set your PSB to 800 and  you should set your Memory to 400MHZ or "Auto" if you have this Choice.You may also come across something called PBS (Processor Bus Speed) which is Actually the FSB Divided by 4 so it is PBS X 4 = FSB in your Case PBS=200 X 4 = 800MHZ FSB or PSB.....But we tend to use FSB in this Forum so as Everybody does NOT get Confused .........Sean REILLY875

  • 848P Neo-LS Fan Control

    As said - no control of the damn fans (Case/CPU) on my 848P Neo-LS. On the CoreCenter the button lits up on mouseover, but when pressed, nothin' happens (as said in manual, press to toggle user/auto modes for fan control).
    Also CoreCenter doesn't show the Case fan's speed, but Northbridge (NB fan) fan's speed, which is obviously 0. Also NB temp is N/A. Also +12V is N/A. Also the FSB stays always at 101 Mhz, not 100. No overclocking done.
    Today upgraded the CoreCenter to the most recent vers (1.7.0.0.), and the button doesn't lit up anymore...?
    When I installed SpeedFan 4.17, it allows me to control the Case fan's speed from 2300 - 2700, but nothing more. Interesting.
    CPU - Celeron 2.0
    RAM - 256 MB Kingston
    CPU Fan - OEM intel fan A80856-003
    Case Fan - MJ 802512
    Both fans with speed sensors, of course.
    Should I update the bios?
    Help somebody!

    To be sure I opened the case and stopped the fans by hand (I don't use the corecenter prg - piece of crap), to see that i have mistaken both fans (in SpeedFan prg). The one who varies by 400 rpm is the Cpu fan.
    Doooh.
    The bios health screen doesn't show +12V at all - just aint there...
    The MSI tech support sez - flash the bios, and if anything doesnt change, the CoreCell chip has gone (faulty, whatever).
    Flashed the bios (1.0 - 1.9 now). No changes.

  • 848P NEO-LS SATA (Native Mode) - Cant Install WinXP

    Okay guys -
    I have a 848P Neo-LS which seems to be somewhat rare on this site in the support sections.
    Its a brand new board and looks very fancy. I have a lot of experience with PC's as I repair them on a daily basis however this is my first adventure into the land of SATA.
    To go with my lovely new MSI motherboard I have purchased a 120GB SATA Hard Disk.
    In the BIOS for the motherboard under "Intergrated Peripherals -> On-Chip IDE Configuration" I can choose to operate the On-Chip ATA in either legacy or native mode. According to the manual that came with the board for Windows XP, I should use Native mode (which is exactly what I want as it allows for 6 ATA devices, as opposed to only 4 with legacy mode - im using a mix of SATA and P-ATA devices).
    When set to Native mode and booting the Windows XP Pro installation CD, it gets so far then I get a blue-screen warning me about a possible harddisk problem?
    But if I set it back to legacy mode and boot the Windows XP Pro installation CD, everything goes through okay and I can choose to begin installing XP if I wish.
    However I want to run in Native mode as this will allow me the mix of SATA and P-ATA Harddisks that I want to run. The manual provided with the MSI board also instructs me that this should be possible.
    Its not working - what is wrong???? From my knowledge of NT based operating systems im guessing I need to press F6 during the installation CD boot sequence and insert a driver disk for the SATA controller? Although it seems strange that this works in legacy mode - perhaps I have answered my own question here and that isnt the problem?
    Or maybe I need a BIOS update, or maybe something entirely different????
    Can someone please answer my question as I would love to get using this wonderful new PC.
    Thanks in advance for any advice.
    Delirum  Sky

    You don't need to install any SATA drivers for your board. I suspect a compatibility issue with the HDD or on of the other SATA/IDE devices you have connected. I would do the following:
    Search the Maxtor site for common issues with your model#
    Install XP in legacy mode and then switch to native mode as suggested above. I have switched back and forth between modes with no trouble.
    If you still get problems,
    1. Update to latest BIOS if one is available. Most new Bios'es on the newer boards include fixes to compatibility issues with SATA devices and memory.
    2. Try installing XP with only the HDD and a generic CDROM or CDRW attached. If this works, install the other devices back one at a time and test to rule them out as the culprit.
    With a recent Bios and your setup I would set On-Chip Config:
    Native mode
    SATA Only
    Keep PATA active-Yes
    Both channels
    Leave rest at default.
    Hope you get it working.

  • [848p Neo S]please Help Me

    Hi
    Please Help Me
    My Pc is Very Slowly
                                      *** any person enterd her replay me please***
    EXAMPLE:-
    TRANSFEAR 4 GB FILMS IN 10 MINUTES
    Component
    MOTHER BOARD MSI 848P NEO S
    PROCESSOR INTEL P4 2.6 CASH 512 PATH 800
    RAM 256 DDR PATH 333
    VGA 128 ATI RADEON 9200 SE
    H.D 80 GB WESTREN DIGITAL 7200 RBM
    SOUND CARD 128 DIGITAL CREATIVE
    FAX INTEL
    PLEASE HELP ME
    WHAT CAN I DO ?
    THANKS

    Hi,
    I would say 4.9Mb/s on such a large file is good....
    1GB = 1024Mb
    1Gb = 2.5 mins to transfer
    Therefore 4.9Mb are transferred every second...... If you are looking for the 100MB/s that's PEAK and not actual......
    Del

  • Problem with 848p NEO V and GeForce FX 5600 point of View

    Hello there,
    I have bought a mobo yesterday (848p NEO V) then when I tried to plug the graphic card (Ge Force FX 5600 point of view) the computer reboots just before entering Win XP PRO.
    So I tried another graphic card (ATI 9200), all worked fine.
    In the same way, I tried my GeForce in another mobo (ECS P4VXAS) and of course all worked fine.
    Each time I tried the MSI mobo with the GeForce card (using diffrents drivers), it doesn't work.
    Does someone know where could this problem come from?
    Thank you very much
    PS: Sorry for my ugly english.

    MOBO: MSI 848p NEO V
    CPU: Intel P4 2.4 A
    Ram: 512 M DDRSDRAM PC3200 (noname) two 256 modules
    DD: 40Go (MAXTOR), 40Go (MAXTOR)
    Display: Point Of View GeForce FX 5600 128mb
    Sound: Sound Blaster Live! 5.1
    Controler Card: Sillicon Image 0680A ULTRA ATA 133
    DVDROM: LG
    CDROM: Samsung
    DVDRW: Liteon
    OS: Win XP Pro SP2 FR (all critical updates installed)
    all cddrive on motherboard IDE controler
    hard drives on controler card
    PSU: 350w noname
    Tell me if you need anything else.
    Thanks

  • MSI 848P neo-V

    my love:
    MSI 848P NEO-V
    CPU celeron 2,4Gh bus 533
    Ram 512Mb
    HDD seagate sata 80Gb
    AGP Asus V9400 X
    today, i make a ghost file with nortonghost ver 7.0, there's strange. Ghost speed just about 100Mb/Min ( same specification with ASROCK is 400Mb/min)  . I don't know why, i think it maybe come from Cmos setting. Mod and ACE please help me.thanks in advance

    thank you, i've just enable it, i will check later, there is another problem, i just bough a CDRW, i install into my computer, but my computer doesn't analize, it looks like nothing install,my computer only analize my old CD, if i take out my old CD then my computer "see" my new CDRW and i use normally. Please help me, i need to use both CDs.thanks
    note: i set master for my old CD and slave for new CDRW.
    one more thing, onchip controller ATA(s) have two selections, one is lagacy mode,one is native mode, please explain what different between them??

  • MSI 848P-Neo - Mobo don't start at all

    Hi,
    I have a MSI 848P-Neo mobo with a P4 Ht 3.0 Ghz on it. New PSU 360W Enermax (12V 26A, 5V 32A, 3.3V 32A). No HDD or CD Drive are plugged. No card in PCI slot, except VGA in AGP Slot. 1 RAM stick in slot.
    When I power on the system, the D-Bracket with Diag led light as follow:
    1 and 3 are red
    2 and 4 are green
    I check in manual for signification but this case isn't in the manual.
    I don't hear beep from speaker.
    Can you confirm me that is the mobo the problem ?

    Have you Clear CMOS Guide yet with power cord removed from the PSU 1st?

  • [848P Neo V] No Post/Dead

    Ok, heres the rundown... just purchased a new computer from newegg, parts include:
    Nvidia FX5500 256MB AGPX8 Video Card
    Kingston 512 Meg stick of Ram, DDR400
    P4 2.4A (Prescot) 533MHZ
    The above board (848P Neo V)
    Power Supply is a 6100 D Powermax, max load= +3.3@28A, +5@30A, +12@25A, [email protected], [email protected], +5vsb@2A
    IBM 80Gig HD connected via IDE, generic CD-RW (Sony) via IDE as well, Floppy.
    Think thats all the information about it thats relevant ;P
    Heres what happens...
    I connect everything up. Everything powers on for a split second (literally.. not even a second) then immediately shuts down. This includes the Power Supply Fan, P4's Fan, the secondary Fan, everything.. I dont even get time to read the diagnostics lights its so fast.
    I've removed the Power Supply, put it into a diffrent computer - works fine. Put a totally seperate power supply in, same problem.
    Tried bypassing the start switch on the case by jumping the MB on, does the same... thing...
    I'm lost. Technically support isnt answering and just makes me leave a message (which they arent returning calls) so not sure where to go with this.
    To make matters worse, its the wife's computer and shes home in 4 hours..ugh! Fix me fix me quick (lol)
    Tim

    Nevermind.. fixed.
    Turns out that the particular case (powermax) dosent have a grounding shield behind it where the MB rests... taking MB out, power on works fine.
    .... What cheap peice of junk company dosent put grounding behind where the mb rests is beyond me....

  • Cant boot computer with 848P neo-v mobo

    Hello
    I've got a pentium 4 computer with 256ram and an MSI 848P Neo-V motherboard. Yesterday I tried to start up the computer without anny problem. I notice that my mouse and keyboard don't work. I press the reset button but it doesn't work. Suddenly I got a black screen. Since the i'm unable to boot the computer. If I press the start button the fan's are working the Hard disk is spinning the processor fan is spinning.
    But that's it nothing on the screen. :(
    So I went looking for the problem I cleared the cmos settings put in a new battery. tried new ram, New harddisk, new Graphics card, new power supply  But its still not working.
    The only strange thing that i'm noticing is that the red led at the front of the case stay's on. Normaly it flashes when the cpu is working but it stay's on. 
    It also seems like the computer Is looking for a dvd.
    Is the motherboard dead or is there a problem that I did not think of.
    Thx 
    Btw: sorry for my bad english

    Hello Realiks,
    please provide full system specs including PSU details.  Read the >>Posting Guide<< to get an idea of what we need to know.

  • 848P Neo-V

    Hello, I've just bought a mainboard MSI 848P Neo-v, Intel P4 3.0Ghz Prescott, and a PowerColor Radeon 9800 Pro 128MB. My problem is that all 3D games gets all messed up, and its getting worser the more you play, dots and stuff. I´ve tried everything i think, changed Agp 4x/8x, fastwrite, changed position of power to graphic card, new/old drivers, bios etc. but nothing works. When i istall PCalert4 it gives me a warning that 3.3V is down under 2.8V, and when i istalled corecenter it tells me the same and that vcore is up 1.7 - 1.8. Is there a way to alter does values? Like boost the 3.3V up.. I think it has to do with the graphic problem, does anyone know? Please help!

    Pentium 4 3.0GHZ 1MB L2 Cache (800Mhz FSB) Prescott
    MSI mainboard 848P Neo-V http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=596
    PowerColor Radeon 9800Pro 128MB AGP 8X http://www.power-color.com/R98-PC3F-128BIT.htm
    DDR 512 MB (2x256 266Mhz) Memory
    2x Harddrives (60 GB/100 GB)
    And the PSU 350W +3.3V - 20A
                                  +5V - 30A
                                +12V - 15A
    That might be the problem, do you think

  • What is my maximum ram memory capacity on Lenovo G575?

    I have bought a lenovo laptop -g575(model: 20081? and it has only 2 GB of ram memory, and if anyone could tell me what is my maximum ram capacity? I currently own 2GB ram, SO-DIMM DDR3, 1333MHz.. I was thinking to get 8gb but im not sure if my laptop will reject it. Please help. Thank you!
    Solved!
    Go to Solution.

    hi StefanThePribic,
    Welcome to Lenovo Community Forums!
    If you system model has two overlaying slots
       It should work with 8 GB    two 4GB cards
    You can also take a look at this
    http://www.crucial.com/upgrade/Lenovo-memory/Essential+%2F+Value+Line/Lenovo+G575-upgrades.html
    Regards
    Solid Cruver
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

Maybe you are looking for