848P Neo (SM Bus Controller) is not there?

Can anyone help me, I am on an MSI 848P using realtek ethernet. I have tried using driver utility cd but cant find anything on SM bus controller. Tried My os xp cd and it couldnt find the drivers.
My comp is a p4 2.6 ghz
512 ddram
ATI 128 9600 graph card
On board sound and ethernet
80 gig hd
dvd and cd rw drives
floppy
The power went out of my apartment Yesterday and then tried to come back on and kinda of surged. It fried my DSL modem and messed with the router. The computer then started acting funny. Like it would start for 1 second then turn off. So i finally got it to turn back on and then bam, The ? mark came up for the SM Bus Controller which i have no clue how to do anything about it. My internet is kinda of screwy. Would that have anything to do with the SM Bus Controller or the on board ethernet???? Also is this a Mother board based Controller or is this a computer problem outside of the MB. Any help would be greatly appreciated.
Thank you

You need to install the Intel INF Drivers.

Similar Messages

Qosmio G50 - SM Bus Controller is not working

Hi,
The SM Bus Controller doesn't seem tpo be working and I can't identify where to get the drivers to load. Can anyone help?
Thanks
Nigel

Hi
I think you need the *Card Reader Controller driver.*
The drivers can be found on the Toshiba European driver page.
The Qosmio G50 is an older series therefore you have to choose Archive in Product Type (first option of driver download form).
Greets

How do i ensure the new access point is joined the controller or not

How do i ensure the new access point is joined the controller or not

To Verifying that Access Points Join the Controller or not there are two ways as below.
Please go through the step by step to find the APs joined state
When replacing a controller, you need to make sure that access points join the new controller.
Using the GUI to Verify that Access Points Join the Controller
Follow these steps to ensure that access points join the new controller.
Step 1 Follow these steps to configure the new controller as a master controller.
a. Click Controller > Advanced > Master Controller Mode to open the Master Controller Configuration page.
b. Check the Master Controller Mode check box.
c. Click Apply to commit your changes.
d. Click Save Configuration to save your changes.
Step 2 (Optional) Flush the ARP and MAC address tables within the network infrastructure. Ask your network administrator for more information about this step.
Step 3 Restart the access points.
Step 4 Once all the access points have joined the new controller, configure the controller not to be a master controller by unchecking the Master Controller Mode check box on the Master Controller Configuration page.
Using the CLI to Verify that Access Points Join the Controller
Follow these steps to ensure that access points join the new controller.
Step 1 To configure the new controller as a master controller, enter this command:
config network master-base enable
Step 2 (Optional) Flush the ARP and MAC address tables within the network infrastructure. Ask your network administrator for more information about this step.
Step 3 Restart the access points.

K8N Neo Plat SM Bus Controller Problems

Hi, I just did a recent build witht the K8N Neo Plat and am having some problems.
My original build kept getting corrupt files from any self extractor that did a self verify. I could install windows and the MSI NForce Drivers but many files got corrupted. I finally figured out it was Bad Ram and replaced the PC 3200 I Was using with a stick of PC 2700 I had lying around. I installed windows with no problems and all of the windows updates(which were where I was getting corrupt files). But then when I installed the NForce3 Drivers from the MSI Cd I get blue screen of death, which I did not recieve with the bad ram. I then revert to last known good setting and can install of of the NForce3 drivers except for SM Bus Controller. I have tried using the NForce3 Drivers from the MSI CD and a download version. Both won't install, it still shows up with an exclamation point next to it in device manager. I have tried choosing the driver directly, but I get an accessed denied message. The only problem is when SM Bus won't install, I cant run my new 6800 GT at AGP 8X. It stays stuck in PCI mode.
Also I see a lot of talk about CPU Temps reported by BIOS. I am using the 1.1 Bios, and it shows the CPU running at 65-70C. Core Center shows this also. Is this just a misreported temp? Im using a 3400+ CLawhammer CG Revision with a Zalman 7000 ALCu with Arctic SIlver 5, the HSF seems to be screwed down completely, but the temp reading still makes me nervous.
Thanks for any help.

apply minimal heat paste
clamp sink down switch machine on
the prob is not the heat the prob is the chip clocking 8ghz
the sink and fan work really well
the bios is version 1.5 public
i'm trying to back flash it but i need version 1.1 .1.2. 1.3 and the prog to fash it
and an explanation (it's my first time lol)

Can not find out Ethernet Controler & SM Bus Controller Driver for P 1000-1404TU Notebook PC

Hi ;
I just purchase a laptop as subject, i installed window 7 64bit and some drivers, but remain 2 drivers as bellow i can not find out in HP Website
Ethernet Controler (wire LAN adapter)
SM Bus Controller.
Could some one help me ?
Many thanks .
This question was solved.
View Solution.

Hi,
Please try:
1. http://ftp.hp.com/pub/softpaq/sp52501-53000/sp52799.exe
2. http://ftp.hp.com/pub/softpaq/sp56501-57000/sp56517.exe
& http://ftp.hp.com/pub/softpaq/sp46501-47000/sp46748.exe
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Sm bus controller (p965 neo)

hi..
i have a new computer with the msi p965 neo board .
i have noticed that i have a problem with something called sm bus controller , which doesnt allow me to connect several usb divices together , i mean , i tried to connect 2 joysticks but only 1 was recognized ...
i looked for drivers for that but couldnt find any .
i am using win xp pro sp2 .
any1 ??

Try un-installing the USB drives and let windows re-detect the drivers again.
You can also try updating your intel.inf driver from Intel.

I have a compaq 6200 pro i can not find the driver for SM bus controller.

I down graded the 6200 pro with the i3 chip to winXP and now I can not find the driver for the SM bus controller does this system have a sm bus controller?

Hi: Please click on the device in the device manager. Then click on the details tab. Post the top string of characters you see. Those will identify the type and model of the missing device and I can send you the link to the drivers. It is either your AMT driver, TPM driver or IMEI driver. In the meantime, install the chipset driver and reboot if you have not done so already. http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lang=en&cc=us&prodTypeId=12454&prodSeriesId=5037900&prodNameId=5037902&swEnvOID=1093&swLang=13&mode=2&taskId=135&swItem=vc-88640-1 Paul

P43 Neo-F - Mystery SM Bus Controller

Hello everyone!
Been rocking my Neo-F since Xmas and what a great board. Just one problem I was hoping you guys could help me with:
When I first installed the board I did a clean install of Win XP and updated drivers and all that, but device manager lists an "SM Bus Controller" that I cannot find drivers for either online or on the software disc bundled with the board.
Does anyone know what it is or where to find drivers for it? Alternatively, how do I disable it so my computer stops worrying about it every startup?
It's probably just me being dense and missing something, but over to you.
Thanks massively for your help.
Cheers.

I had the same problem with the public Windows 7 beta on my P45 Neo-3 FR board.
I solved it by installing the latest INF Update Utility (9.1.0.1012 WHQL).
They are generic (board/OS), so they will probably solve your problem as well.

MSI 848P neo-V

my love:
MSI 848P NEO-V
CPU celeron 2,4Gh bus 533
Ram 512Mb
HDD seagate sata 80Gb
AGP Asus V9400 X
today, i make a ghost file with nortonghost ver 7.0, there's strange. Ghost speed just about 100Mb/Min ( same specification with ASROCK is 400Mb/min) . I don't know why, i think it maybe come from Cmos setting. Mod and ACE please help me.thanks in advance

thank you, i've just enable it, i will check later, there is another problem, i just bough a CDRW, i install into my computer, but my computer doesn't analize, it looks like nothing install,my computer only analize my old CD, if i take out my old CD then my computer "see" my new CDRW and i use normally. Please help me, i need to use both CDs.thanks
note: i set master for my old CD and slave for new CDRW.
one more thing, onchip controller ATA(s) have two selections, one is lagacy mode,one is native mode, please explain what different between them??

[Athlon64] CAN'T SEE SINGLE SATA DRIVE / K8T NEO no Promise controller

I have a K8t NEO -the cheapskate version with no PROMISE SATA controller or on-board Firewire
I have been running on XP SP2 on 2 IDE drives, everything is ok. I added a SINGLE SATA drive and turned the VIA SATA controller on in BIOS. I did the MSI Live Update and have the latest VIA SATA driver, latest chipset, latest BIOS, latest EVERYTHING. At boot, the VIA SATA controller reports my Hitachi SATA as Channel 0 Primary" in the SATA devices table. Going into the SATA RAID menu it tells me "You can't make RAID with just one drive" which is true, of course. But the point is the controller SEES the drive.
I've run MSI Live Update and have the latest BIOS, latest SATA XP driver, latest EVERYTHING.
Windows XP doesn't see the SATA drive.
In XP I see a VIA RAID CONTROLLER in Hardware / Device Manager which is DISABLED. When I right-click then click ENABLE on the VIA RAID CONTROLLER the machine reboots immediately. I tried safe mode, same thing. I tried BIOS settings of "No PNP O/S Installed" and "Yes PNP O/S Installed" and reset the NVRAM. No change.
I think there must be an IRQ conflict.... I have a sound card (on-board sound is turned OFF in BIOS) and AGP video card, and that's it- no WiFi NIC or anything else to eat up IRQ resources. I use the Realtek on-board ethernet.
I tried my Windows 98 partition and that booted, detected the new hardware (VIA SATA) and I installed the driver from the MSI CD and Win 98 is happy with the SATA drive..... it sees the drive just fine.
How do I make Windows XP see the SATA drive?

Have you tried starting XP with CD and entering recovery, log on as admin and see if SATA drive is there? Remember to "F6" with a floppy drive of SATA drivers for
-XP-... I'm assuming you already have as you said all is uptodate. When the boot BIOS for the VIA SATA apprears and you press "TAB" I believe it is, you can mess with the SATA functions. Sorry if does not apply to your compy or you've already done all this.... BTW you CAN run a RAID array with one HDD, at least thats what I did on my Promise controller.
In my Device Manager under Disk drives it looks like this (notes bracketed are noting position):
Promise 1+0 Stripe/RAID0 SCSI Disk Device (Bus Number 0, Target ID 1, LUN 0 (G:\ 1-160GB IDE Seagate/notice ONE drive)
Promise 2+0 Stripe/RAID0 SCSI Disk Device (Bus Number 0, Target ID 0, LUN 0) (F:\ 2x200 SATA)
ST3160023A (Location 1 (1) VIA IDE D:\)
VIA SATA RAID 0 SCSI Disk Device (Bus Number 0, Target ID 0, LUN 0) (E:\ 2x120 SATA)
WDC WD800JB-00CRA1 (Location 0 (0) VIA IDE C:\)
Under the boards BIOS, is the SATA drive listed under the BOOT table??? In my system it lists the above 5 partitions (7 HDD's total), floppy, 2 CD/DVD drives, etc...
Oh also in Device Manager IS the VIA SATA controller appearing in the "SCSI and RAID controllers" tab??? I have set mine to just SATA before and of course now it says "VIA SATA RAID Controller"... for you it should read "VIA SATA Controller". Remember there are 2 different drivers for the SATA controller, one for SATA and one for SATA RAID. Look on your floppy disk or if you saved out the updated driver. I made a new floppy with the latest XP drivers. When booting from WINXP CD, and promted for "F6" and press it, later it will show you TWO different drivers after reading the floppy disk for XP. You obviously want the non RAID driver... hope that helps somewhat... g'luck

848P Neo-LS [help configuring ...]

I just set up a 848P Neo-LS
support for:
800mhz FSB
400mhz DDR
I installed a P4 2.8c which should be able to run at 800mhz
I don't feel the mainboard manual give enough detail to explain how to set up the bios and when i view "CORECENTER" it shows my pc running at 200mhz FSB. and when i click where it shows this on the right pannel, what's with the 200mhz x 14.0=2807 mhz?
I just want to make sure my pc is running at 800mhz FSB and my 400mhz pc3200 ram i have is running optimally as well.
ALSO, in the bios it shows the DRAM, PSB 400MHZ, PSB533 MHZ AND PSB800MHZ.
IF PSB is stands for another bus what bus is it and y do the equivalants to 400, 533 and 800 only = 100-344mhz, 133-500mhz and 200-500mhz respectively?
ANY help would be appreciated, i know from viewing this forum that there are MANY of u out there that are EXPERTS with MSI boards and setting them up.
thanks for any help
IRISHHUNK
(St.PAtricks day's commin up, have fun

And PSB (Processor Speed on BUS) is Basically the same as FSB (Front side Bus) only it is a different Name, So set your PSB to 800 and you should set your Memory to 400MHZ or "Auto" if you have this Choice.You may also come across something called PBS (Processor Bus Speed) which is Actually the FSB Divided by 4 so it is PBS X 4 = FSB in your Case PBS=200 X 4 = 800MHZ FSB or PSB.....But we tend to use FSB in this Forum so as Everybody does NOT get Confused .........Sean REILLY875

Need SM Bus Controller Driver for A75-S231

Unfortunately I am without my system and backup disks and I am in desperate need of a driver for the SM Bus Controller. Problem surfaced after re-install of XP Home.
I called Toshiba tech support to identify the motherboard chipset shipped with my unit (specs listed at end of post) so as to locate and download the driver. Unbelievably, Tech is not equipped to identify the make or model of my motherboard or identify the chipset. Third Party software tells me I have a Toshiba EDW10 Motherboard and tech searched the internet and told me I have some VIA motherboard and good luck finding your driver.
Please help, I didnt think that Toshiba of all people would be unable to identify their own systems but here I am 4 hours later bothering you good people and still hunting. Does anyone have the SM Bus controller driver for the A75-S231 or tell me what chipset was shipped with my unknown motherboard?
My system specs are as follows:
OS Name Microsoft Windows XP Home Edition
Version 5.1.2600 Service Pack 2 Build 2600
System Manufacturer TOSHIBA
System Model Satellite A75
System Type X86-based PC
Processor x86 Family 15 Model 4 Stepping 1 GenuineIntel ~3333 Mhz
Processor x86 Family 15 Model 4 Stepping 1 GenuineIntel ~3333 Mhz
BIOS Version/Date TOSHIBA V1.30, 9/10/2004
SMBIOS Version 2.31
Hardware Abstraction Layer Version = "5.1.2600.2180 (xpsp_sp2_rtm.040803-2158)"
Total Physical Memory 512.00 MB
SM Bus Controller Device ID (from Device Manager) PCI\VEN_1002&DEV_4353&SUBSYS_FF001179&REV_18\3&61A AA01&0&A0
Motherboard Toshiba EDW10???
Thanks fo your help.

Hi
As far as I know your unit must be an US notebook model and please try to check Toshiba US download page under http://www.csd.toshiba.com/cgi-bin/tais/su/su_sc_home.jsp
Please dont be mad on tech support but I dont see any reason why they should know every technical detail of your notebook. Toshiba has designed drivers for every hardware component that you can have anytime you want and install it 1000 times if you want. Toshiba guarantee that it will work properly and I dont see any problem there.
Technical details you can get from Authorized service partners in your country.
Good luck!

848P Neo-LS Fan Control

As said - no control of the damn fans (Case/CPU) on my 848P Neo-LS. On the CoreCenter the button lits up on mouseover, but when pressed, nothin' happens (as said in manual, press to toggle user/auto modes for fan control).
Also CoreCenter doesn't show the Case fan's speed, but Northbridge (NB fan) fan's speed, which is obviously 0. Also NB temp is N/A. Also +12V is N/A. Also the FSB stays always at 101 Mhz, not 100. No overclocking done.
Today upgraded the CoreCenter to the most recent vers (1.7.0.0.), and the button doesn't lit up anymore...?
When I installed SpeedFan 4.17, it allows me to control the Case fan's speed from 2300 - 2700, but nothing more. Interesting.
CPU - Celeron 2.0
RAM - 256 MB Kingston
CPU Fan - OEM intel fan A80856-003
Case Fan - MJ 802512
Both fans with speed sensors, of course.
Should I update the bios?
Help somebody!

To be sure I opened the case and stopped the fans by hand (I don't use the corecenter prg - piece of crap), to see that i have mistaken both fans (in SpeedFan prg). The one who varies by 400 rpm is the Cpu fan.
Doooh.
The bios health screen doesn't show +12V at all - just aint there...
The MSI tech support sez - flash the bios, and if anything doesnt change, the CoreCell chip has gone (faulty, whatever).
Flashed the bios (1.0 - 1.9 now). No changes.

848P NEO-LS SATA (Native Mode) - Cant Install WinXP

Okay guys -
I have a 848P Neo-LS which seems to be somewhat rare on this site in the support sections.
Its a brand new board and looks very fancy. I have a lot of experience with PC's as I repair them on a daily basis however this is my first adventure into the land of SATA.
To go with my lovely new MSI motherboard I have purchased a 120GB SATA Hard Disk.
In the BIOS for the motherboard under "Intergrated Peripherals -> On-Chip IDE Configuration" I can choose to operate the On-Chip ATA in either legacy or native mode. According to the manual that came with the board for Windows XP, I should use Native mode (which is exactly what I want as it allows for 6 ATA devices, as opposed to only 4 with legacy mode - im using a mix of SATA and P-ATA devices).
When set to Native mode and booting the Windows XP Pro installation CD, it gets so far then I get a blue-screen warning me about a possible harddisk problem?
But if I set it back to legacy mode and boot the Windows XP Pro installation CD, everything goes through okay and I can choose to begin installing XP if I wish.
However I want to run in Native mode as this will allow me the mix of SATA and P-ATA Harddisks that I want to run. The manual provided with the MSI board also instructs me that this should be possible.
Its not working - what is wrong???? From my knowledge of NT based operating systems im guessing I need to press F6 during the installation CD boot sequence and insert a driver disk for the SATA controller? Although it seems strange that this works in legacy mode - perhaps I have answered my own question here and that isnt the problem?
Or maybe I need a BIOS update, or maybe something entirely different????
Can someone please answer my question as I would love to get using this wonderful new PC.
Thanks in advance for any advice.
Delirum Sky

You don't need to install any SATA drivers for your board. I suspect a compatibility issue with the HDD or on of the other SATA/IDE devices you have connected. I would do the following:
Search the Maxtor site for common issues with your model#
Install XP in legacy mode and then switch to native mode as suggested above. I have switched back and forth between modes with no trouble.
If you still get problems,
1. Update to latest BIOS if one is available. Most new Bios'es on the newer boards include fixes to compatibility issues with SATA devices and memory.
2. Try installing XP with only the HDD and a generic CDROM or CDRW attached. If this works, install the other devices back one at a time and test to rule them out as the culprit.
With a recent Bios and your setup I would set On-Chip Config:
Native mode
SATA Only
Keep PATA active-Yes
Both channels
Leave rest at default.
Hope you get it working.

Satellite L30-114 - Need driver for sound and SM bus controller

Hi, friends
Plz I need your help on my Satellite L30-114. Am having problems with the sound and the SM bus controller, even I have downloaded the sound driver and install it, from my device manager sound is not sick, it always telling me my device is working properly? Plz i need help on that.
Secondly my SM bus controller is sick it has the cormer sign plz how can I rectify it, even my wireless is working fine.
Only the sound and sm bus controller is giving problems.
Thanks will be waiting for your replies.
newton

Hi
To be honest I doubt that you have installed all files from the Toshiba website. Normally the Toshiba website contains all drivers and tools that you need to restore factory settings after this there are no more yellow exclamation marks or unknown devices in device manager.
By the way: What installation order you have used?
On the Toshiba website you can find the installation instructions document. This is a list for the recommended driver installation order.
Check this!!!

848P Neo (SM Bus Controller) is not there?

Similar Messages

Maybe you are looking for