8500 WLC Console Access

Hi,
It might be a silly question, but I stuck with it from 30 mins trying to Console to Cisco 8500 WLC.
As per the Installation and Configuration Guide, I used DB-9 to RJ-45 Converter to console into the WLC. But Putty and Teraterm doesn't detect the console cable at all.
I tried to find the procedure from Cisco docs, but no luck.
I have connected VGA, USB ports to Monitor and Keyboard - Mouse and the boot process stuck at
Decompressing Linux......done.
Booting the kernel
I looked at the following post, which has same issue, but no resolution posted there
https://supportforums.cisco.com/thread/2234788
Any help as how to gain console access to the Cisco 8500 WLC using DB-9 to RJ-45 Converter and RF-45 cable.
Thanks,
CJ

Did you find any solution to this?. I am facing the same issue with a recently purchased 8510 WLC.
This box is similar to the ISE so I decided to use the VGA, USB ports to Monitor and Keyboard - Mouse but as indicated above, the boot process stuck at:
Decompressing Linux, done
Booting the kernel
Cisco sent the box with a DB-9 - 3.5mm termination (like headphone cable termination) black cable but the ports to connect that 3.5 termination to the WLC said in the Figure 1-6 of Cisco doc: "CONSOLE PORT NOT USED". 
Looks like I should open a TAC Case. Any ideas?
thanks

Similar Messages

  • Console Access to CPO Server in a different time zone: Verifying Security

    Hello,
    I noticed this on multiple instances, when CPO console in one timezone (example: CST) tries to access a CPO Server in a totally different timezone, the console is not able to login to the CPO Server and I see this error message:
    "An error occurred when verifying security for the message"
    Is there any known issue with console accessing the CPO server and some handshake happening?
    From the logs:
    @@Logging from process Tidal.Automation.Console.Loader.exe(id=13248)
    ||8|2013/03/06 19:20:00.365|13736||||Could not get server ID for assembly store connection:
    ||9|2013/03/06 19:20:00.366|13736||||EXCEPTION (System.ServiceModel.Security.MessageSecurityException): An unsecured or incorrectly secured fault was received from the other party. See the inner FaultException for the fault code and detail.
    Stack Trace:
    Server stack trace:
       at System.ServiceModel.Channels.SecurityChannelFactory`1.SecurityRequestChannel.ProcessReply(Message reply, SecurityProtocolCorrelationState correlationState, TimeSpan timeout)
       at System.ServiceModel.Channels.SecurityChannelFactory`1.SecurityRequestChannel.Request(Message message, TimeSpan timeout)
       at System.ServiceModel.Security.SecuritySessionSecurityTokenProvider.DoOperation(SecuritySessionOperation operation, EndpointAddress target, Uri via, SecurityToken currentToken, TimeSpan timeout)
       at System.ServiceModel.Security.SecuritySessionSecurityTokenProvider.GetTokenCore(TimeSpan timeout)
       at System.IdentityModel.Selectors.SecurityTokenProvider.GetToken(TimeSpan timeout)
       at System.ServiceModel.Security.SecuritySessionClientSettings`1.ClientSecuritySessionChannel.OnOpen(TimeSpan timeout)
       at System.ServiceModel.Channels.CommunicationObject.Open(TimeSpan timeout)
       at System.ServiceModel.Channels.ServiceChannel.OnOpen(TimeSpan timeout)
       at System.ServiceModel.Channels.CommunicationObject.Open(TimeSpan timeout)
       at System.ServiceModel.Channels.ServiceChannel.CallOnceManager.CallOnce(TimeSpan timeout, CallOnceManager cascade)
       at System.ServiceModel.Channels.ServiceChannel.EnsureOpened(TimeSpan timeout)
       at System.ServiceModel.Channels.ServiceChannel.Call(String action, Boolean oneway, ProxyOperationRuntime operation, Object[] ins, Object[] outs, TimeSpan timeout)
       at System.ServiceModel.Channels.ServiceChannelProxy.InvokeService(IMethodCallMessage methodCall, ProxyOperationRuntime operation)
       at System.ServiceModel.Channels.ServiceChannelProxy.Invoke(IMessage message)
    Exception rethrown at [0]:
       at System.Runtime.Remoting.Proxies.RealProxy.HandleReturnMessage(IMessage reqMsg, IMessage retMsg)
       at System.Runtime.Remoting.Proxies.RealProxy.PrivateInvoke(MessageData& msgData, Int32 type)
       at Tidal.Automation.Common.AssemblyManager.IAssemblyManager.GetServerId()
       at Tidal.Automation.WinForms.Loader.AssemblyStore.GetRequiredFiles()
    ||10|2013/03/06 19:20:00.366|13736||||   INNER EXCEPTION (System.ServiceModel.FaultException): An error occurred when verifying security for the message.
    Stack Trace:
    ||11|2013/03/06 19:20:37.696|13736||||Could not get server ID for assembly store connection:
    ||12|2013/03/06 19:20:37.696|13736||||EXCEPTION (System.ServiceModel.Security.MessageSecurityException): An unsecured or incorrectly secured fault was received from the other party. See the inner FaultException for the fault code and detail.
    Stack Trace:
    Server stack trace:
       at System.ServiceModel.Channels.SecurityChannelFactory`1.SecurityRequestChannel.ProcessReply(Message reply, SecurityProtocolCorrelationState correlationState, TimeSpan timeout)
       at System.ServiceModel.Channels.SecurityChannelFactory`1.SecurityRequestChannel.Request(Message message, TimeSpan timeout)
       at System.ServiceModel.Security.SecuritySessionSecurityTokenProvider.DoOperation(SecuritySessionOperation operation, EndpointAddress target, Uri via, SecurityToken currentToken, TimeSpan timeout)
       at System.ServiceModel.Security.SecuritySessionSecurityTokenProvider.GetTokenCore(TimeSpan timeout)
       at System.IdentityModel.Selectors.SecurityTokenProvider.GetToken(TimeSpan timeout)
       at System.ServiceModel.Security.SecuritySessionClientSettings`1.ClientSecuritySessionChannel.OnOpen(TimeSpan timeout)
       at System.ServiceModel.Channels.CommunicationObject.Open(TimeSpan timeout)
       at System.ServiceModel.Channels.ServiceChannel.OnOpen(TimeSpan timeout)
       at System.ServiceModel.Channels.CommunicationObject.Open(TimeSpan timeout)
       at System.ServiceModel.Channels.ServiceChannel.CallOnceManager.CallOnce(TimeSpan timeout, CallOnceManager cascade)
       at System.ServiceModel.Channels.ServiceChannel.EnsureOpened(TimeSpan timeout)
       at System.ServiceModel.Channels.ServiceChannel.Call(String action, Boolean oneway, ProxyOperationRuntime operation, Object[] ins, Object[] outs, TimeSpan timeout)
       at System.ServiceModel.Channels.ServiceChannelProxy.InvokeService(IMethodCallMessage methodCall, ProxyOperationRuntime operation)
       at System.ServiceModel.Channels.ServiceChannelProxy.Invoke(IMessage message)
    Exception rethrown at [0]:
       at System.Runtime.Remoting.Proxies.RealProxy.HandleReturnMessage(IMessage reqMsg, IMessage retMsg)
       at System.Runtime.Remoting.Proxies.RealProxy.PrivateInvoke(MessageData& msgData, Int32 type)
       at Tidal.Automation.Common.AssemblyManager.IAssemblyManager.GetServerId()
       at Tidal.Automation.WinForms.Loader.AssemblyStore.GetRequiredFiles()
    ||13|2013/03/06 19:20:37.696|13736||||   INNER EXCEPTION (System.ServiceModel.FaultException): An error occurred when verifying security for the message.
    Stack Trace:

    More important than whether their timezones differ is whether their *times* differ.
    12:00 in EST = 9:00 in PST as far as everyone (including Windows) is concerned.
    If both are showing 12:00 then time sync is the problem, and this would cause authentication handshake issues.  NT authentication only allows something like 10 minutes of clock skew.  My example here has 180 minutes of clock skew.

  • Console access via SERIAL MGT port on v210

    This is a simple question. I just want the standard way to use Hypertem off my laptop in order to have a CONSOLE session on a v210. NOT AOLM, I want to be able to have console access, running in single user mode, etc.
    I have a USB SERIAL connector that ends with a DB-9 connector. I have a NULL MODEM cable, DB-9 at both ends.
    I am supposed to use the RJ-45 SERIAL MGT port on the back of the v210, correct?
    I believe then that I need a connector that is RJ-45 on one end and DB-9 at the other. And so, where do I get that? I have seen a silver connector like that when I have opened new servers before. But I don't have one. Can I buy one???

    If you have a Sun support contract you can ask your local support team to provide you with a T3 connector kit. If no contract, http://www.infosystemssupply.com/products77.html

  • Design console access in OIM 11gR2

    I need to create an user other than Xelsysadm to have access to design console in OIM11gR2. what are the steps in 11gR2. In R1 i used to select the Design console access checkbox while creating user manually. Is there any feature like that in 11gR2. Thanks in advance

    provide Admin Role to the user.
    goto-> organizatin-> search and select Top organization-> open detail page-> click on Admin Role-> select Adminrole(System Administrator or User Administrator etc.) -> click on Assign button-> select user and add it-> finally click on okay.
    make sure you select the 'sub-organization hirearchy'

  • Minimum permisions required to get Design Console access

    Hi,
    What are the minimum permissions required by User (expect for checking the Design Console checkbox on user profile) to access Design Console in OIM 11g R1 (11.1.1.5.0)?
    Ofcourse, we donot want to add the user in System Admin group.
    We just want that the user is able to modify the lookups thru' DC.
    Thanks
    Sid
    Edited by: Sidharath on Dec 13, 2012 12:46 PM

    11g: End-User Administrator (Select Design Console Access Attribute)
    Permissions you can give :
    Go to Role > Data Object permission > Select desired permissions from there
    Metalink: ID 1495238.1]
    R2: OIM 11gR2 Design Console Access

  • Azure Pack Private Cloud RDP GateWay Configuration Console Access

    Hello,
    We are in the process of deploying the Azure Pack Private Cloud and have run into an issue with configuration of the Console Access.  We have been able to successfully configure the Console to work internally but external access is not functional.  When
    a user attempts to connect from Windows 8.1 to the RDP Console via the Remote Desktop Services Gateway they are seeing the error:
    An Authentication error has occurred (code 0x607)
    Internal access works flawlessly.
    Environment: Windows Server 2012r2 Data Center, fully updated
    Windows Azure Pack RTM - Distributed Installation - 7 VMs - wapadmapi1, wapadmauth1, wapadmprtl1, waptenauth1, waptenprtl1, waptenpriapi1, waptenpubapi1
    System Center 2012r2 Components: VMM, Service Provider Foundation, SCORCH, SCOM
    SQL Server 2012 Enterprise SP1 running on Server 2012r2
    Hyper-V Failover Cluster 2012r2
    Wildcard Certificate has been assigned and RDP Gateway/VMM/SPF/Hyper-V have been configured as per http://www.hyper-v.nu/archives/mvaneijk/2013/09/windows-azure-pack-console-connect/ (PS this article needs to be updated because the set-scspfvmconnectglobalsettings
    cmdlet doesn't work on RTM) and http://technet.microsoft.com/en-US/library/dn469415.aspx
    Thanks,
    Rick

    No problem Dennis, as noted in the two articles I referenced above:
    http://www.hyper-v.nu/archives/mvaneijk/2013/09/windows-azure-pack-console-connect/  and http://technet.microsoft.com/en-US/library/dn469415.aspx
    an RDP Gateway is required to connect the external user to the console access on the Hyper-V backend
    server.  When the RDP file is downloaded it enables users to have more functionality than a standard RDP session and it also allows you access to internal resources, acting similar to a proxy.  I have checked the security logs and there is nothing
    that jumps out at me.
    Here is an excerpt from the logs:
    The user "FedAuthDomain\FedAuthUser", on client computer "CLIENT_EXT_IP", met connection authorization policy requirements and was therefore authorized to access the RD Gateway server. The authentication method used was: "Cookie" and connection protocol
    used: "HTTP".
    The user "FedAuthDomain\FedAuthUser", on client computer "CLIENT_EXT_IP", met resource authorization policy requirements and was therefore authorized to connect to resource "HV_SERVER_INT_IP".
    The user "FedAuthDomain\FedAuthUser", on client computer "CLIENT_EXT_IP", connected to resource "HV_SERVER_INT_IP". Connection protocol used: "HTTP".
    The user "FedAuthDomain\FedAuthUser", on client computer "CLIENT_EXT_IP", disconnected from the following network resource: "HV_SERVER_INT_IP". Before the user disconnected, the client transferred 1254 bytes and received 1615 bytes. The client session duration
    was 0 seconds. Connection protocol used: "HTTP".
    I have removed the actual IP addresses from the logs but kept the user credentials that are being currently passed.  HV_SERVER_INT_IP = IP of Hyper-V Host, internal and CLIENT_EXT_IP = IP of client who is attempting to access.

  • KVM Console Access to Servers in UCS Failed- Connection failed !

    Dear Team,
    All of a sudden we were not able to take KVM of Servers,for all servers from
    both chasis
    In Java console it was showing Connection time out error
    og4j:WARN No appenders could be found for logger (com.nuova.centrale.core.log4j.NuRollingFileAppender).
    log4j:WARN Please initialize the log4j system properly.
    Connection failed.
    Not even able to ping the KVM Console IP that was working fine all these days (IP are of same range as of FI)
    After 1 hour of trouble shooting ,we finally decided to reboot FI-A
    and FI-B took over as cluster lead-primary,then we were able to take KVM of servers.
    We also looked at the PDF UCSM-kvm-troubleshooting-00
    Now after reboot FIA came up and we did not wait for the primary role switch over,but logged into FIB and made FIA as primary on doing this we lost KVM COnsole access.
    So now we rebooted FIA again and FI-B took over as cluster lead-primary,then we were able to take KVM of servers.Now this time after FI-A came up after reboot we waited for  the primary switch over to happen by itself and after sometime FI-A got its role back as primary and KVM access started working fine
    so would like to know..the initial issue with FI-A is it because of CIMC hung? and on forcefull manual change over of FI-A as primary did not help in getting KVM console access any reason?
    Thanks and Regard
    Jose

    Hi Padma,
    We have 2 FI A and B
    say A is 21 B is 22 and 20 cluster ip
    Are you able to ping FI A and B mgmt interface IP address ?
    how we are connecting is ,we connect from FI A mgmt port to a switch
    and there we manage at this point we can ping 21 and 20 not 22 and vice versa
    Have you ever rebooted CIMC of the blade ?
    We did not reboot CIMC alone ,we rebooted a server itself
    how to reboot CIMC alone?
    Did it happen for all blades managed by FI A ?
    yes we checked from both chasis,physical connectvity given from both FI
    Thanks and Regards
    Jose

  • How to give design console access to the user from OIM GUI - OIM 11g R2

    Hi,
    Could you please let me know if there is any way to give Design Console access to a normal user in OIM 11g R2.
    I tried by giving the access from backend by using DB command and I was able to give the design console access to the user.
    But I need to give design console access to the user from OIM Interface.
    Please let me know how to achieve this functionality.
    Thanks

    I have already used this approach by directly modifying the user record in DB.
    I am looking if it is possible to give Design console access from OIM GUI, the way we use to give in OIM 11g R1.

  • Usb to serial converter console access on aironet 1131

    I am having difficulty accessing the console port utilizing a usb to serial converter. My settings are 9600, 8,n,1 and flow control is none.
    The converter works if I use it for switches and router but fails on the aironet.
    I can access the aironet if I go directly to the serial port.

    Hi,
    I haven't seen this problem except when I chose the incorrect COM port in my terminal emulator. Otherwise, usb-to-serial cables haven't presented any issues with Aironet equipment.
    Sorry I couldn't help further. Maybe someone else has seen this issue.
    -Ben

  • Oracle VM Manager 3.0 - Virtual Machine Console Access

    Does anybody else out there seem to have problems launching the console to get into a VM Guest? When we do, we get the login screen and then nothing. It doesn't appear to be firewall related. We had similiar issues in 2.2.
    Any tricks on this?

    user11899891 wrote:
    Does anybody else out there seem to have problems launching the console to get into a VM Guest? When we do, we get the login screen and then nothing. It doesn't appear to be firewall related. We had similiar issues in 2.2.There is no direct VNC access between your client and the Oracle VM Servers any more. Ensure you have port 15901 open from the client desktop to the Oracle VM Manager machine and that you have all the VNC ports open from Oracle VM Manager to the Oracle VM Servers. We now proxy VNC via the Manager for improved security and simpler configurations.
    Also, you will still need to install the tightvnc-java RPM separately, as described in the documentation, to ensure the Java VNC console is installed. This needs to be installed on your Oracle VM Manager server.

  • Console access through USB- Solaris x86

    Hi,
    I installed Solaris 9 on my laptop, Compaq Presario V2000 Series. My laptop does not have a Serial Port attached. I was wondering whether I can access the console through USB . And if so, can you please also provide me the instructions on how to configure it.
    soladmin2006

    Hello.
    /dev/dsk/c7t0d0s0The "s" tells me that you use a Sparc system - right?
    /dev/dsk/c7t0d0s0
    "s0" is the primary partition on Sparc formatted disks.
    The whole disk is identified by "s2" on Sparc systems.
    If the floppy disk does not have a partition table (this is the case for removable media such as 3.5" disks) you should use
    /dev/dsk/c7t0d0s2
    For non-removable or integrated media (such as "USB sticks") XP often adds a partition table. In this case you must add ":c" to the partition name:
    /dev/dsk/c7t0d0s2:c
    Martin

  • Issue with console access when OHS is configured in front of Weblogic

    I have configured the OHS virtual host in front of weblogic server for accessing the console. The OHS and weblogic are on different machine and I am using the port based virtual hosting. I am able to access the console using the virtual host but when I click on 'Activate changes' after deployment/delete, the url is redirected to the Admin server url, and I get the login page again.
    This redirection does not happen when the OHS virtual host and weblogic server are using the same port number. What I have observed is while 'Activating changes' the port number in the url is compared to the admin server and channel's port and if it does not match then connection is reset to the Admin server url.
    Can anyone please suggest why this redirection is happening?

    Not sure which version of WebLogic Server you are using, but recent versions have a console preference, "Follow configuration changes", that can be disabled to avoid changing urls to server-centric ports on activation. Clear that setting and try this again.

  • ISE deployment in wireless infra without WLC (only Access Point 1240AG)

    Hello All,
    I am having access point 1240AG and planning to deploy ISE as a exteral radius server. I would like to know how deifferent authorization policy need to configure in AP/ISE. Whether I can use named ACL or VLANs (CoA) as a enforcement types without use of WLC. If yes then how?
    Thanks in advance.

    Hi,
    You can perform COA on standalone APs you will need to have an inline posture node in order to reap the benefits of COA, you may have heard this from any vpn related deployments. If you are in the design phase of this project, you may want to purse controllers because the latest rumor is that the inline posture node may be dropped since Cisco is planning on supporting coa on all their devices once the 9.x code drops for the ASAs. However please contact your Cisco rep for an official response.
    Here is the footnote in the following link: "Autonomous AP deployments (no WLC) also require deployment of an Inline Posture Node for posture support."
    http://www.cisco.com/en/US/docs/security/ise/1.1/compatibility/ise_sdt.html#wp55038
    Thanks,
    Tarik admani

  • BPEL Console access question

    Hi,
    While checking the instances activity flow in the BPEL Console, when you click on any activity you see a pop-up with the data that is passed, in XML format. I want to know if we can restrict the data that is viewed in here, so the users do not see sensitive data that is passed for integration and only the basic data.
    Is this doable? If so, appreciate if you can give some direction on how to go about doing this.
    Thanks
    -Prapoorna

    You can certainly restrict who can view the data by limiting the membership in the SoaGroup instead of granting widespread access.
    If you want to control what they see, the first thing I would try would be to encrypt the data for sensitive items within the elements:
    <AccountNumber>{3DES}...</AccountNumber> instead of <AccountNumber>12345</AccountNumber>
    I don't see any way to restrict what fields are visibile to one user versus another, or a way to hide particular fields.

  • Collaboration Administration Console Access Error

    Hi,
    I have installed and configured webcenter collaboration but I am getting below error when I am trying to access Administration Console for Collaboration. I tried two times and get the same error.
    com/plumtree/core/db/DBManager
              com.plumtree.collaboration.api.portalaccess.PortalAccessManager.getGuestPortals(PortalAccessManager.java:287)
              com.plumtree.collaboration.api.portalaccess.PortalAccessManager.fillMap(PortalAccessManager.java:396)
              com.plumtree.collaboration.api.portalaccess.PortalAccessManager.initialize(PortalAccessManager.java:323)
              com.plumtree.collaboration.api.portalaccess.PortalAccessManager.<clinit>(PortalAccessManager.java:55)
              com.plumtree.collaboration.context.CollaborationContextFactory.createCollaborationContext(CollaborationContextFactory.java:72)
              com.plumtree.collaboration.webui.framework.action.CollaborationController.service(CollaborationController.java:90)
              javax.servlet.http.HttpServlet.service(HttpServlet.java:803)
              org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:290)
              org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206)
              org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperValve.java:233)
              org.apache.catalina.core.StandardContextValve.invoke(StandardContextValve.java:175)
              org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.java:128)
              org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.java:102)
              org.apache.catalina.core.StandardEngineValve.invoke(StandardEngineValve.java:109)
              org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.java:263)
              org.apache.coyote.http11.Http11NioProcessor.process(Http11NioProcessor.java:887)
              org.apache.coyote.http11.Http11NioProtocol412Http11ConnectionHandler.process(Http11NioProtocol.java:696)
              org.apache.tomcat.util.net.NioEndpoint412SocketProcessor.run(NioEndpoint.java:2009)
              java.util.concurrent.ThreadPoolExecutor412Worker.runTask(ThreadPoolExecutor.java:650)
              java.util.concurrent.ThreadPoolExecutor412Worker.run(ThreadPoolExecutor.java:675)
              java.lang.Thread.run(Thread.java:595)
    also collaboration diaognostic URL giving me no details on the screen.
    Does anyone have clue ?
    - Mukesh

    You might want to check that you ran all of the database scripts for Collaboration. Some scripts must be run as the collabdbuser and the others must be run as portaldbuser. It might be possible that the portal can't access the Collaboration database or vice versa.

Maybe you are looking for

  • Video to ipod question

    i have some south park episodes on my hd and they dont want to transfer on to my ipod does anyone have any suggestions?

  • AWR snapshot not generatedand how to compare statistics with a baseline

    01. AWR snapshot not being generated even after setting looks fine 02. compare a captured set of statistics with a baseline. i m not much clear on this, please help as i have this requirement at hand. Thanks a lot in advance.

  • Vendor code missing in SC from Internal catalog

    Hi, I have an issue while creating shopping cart from a perticular Internal catalog. I have selected 4 catalogs items from the Internal catalog. while After ordered the SC the system created a Purchase requisition in the backend R/3 instead creation

  • Printer setting at unix level

    Hi Connoisseur of SAP Basis, i am very new to SAP Basis, could you people help  me out with the exact set up of printer in unix level, step wise step. thank you. Dilip

  • Need help importing from HD camcorder

    Hey, So i just purchased a new canon vixia hf10 HD camcorder. when i create a new project and attempt to import files into the computer, it tells me there's something wrong (i think it said something about firewire, which doesnt make sense cuz it's i