8520 Red Light Youtube Problem

Hi, Long time reader, First time poster.
Firstly I am on O2 UK - Using Blackberry OS V.5.0.0.681
Just a quick problem I am having with my Blackberry 8520 which is every time i try using Youtube either via Application Youtube Player or through the Browser the phone shuts off and I get the red Light on the top, This didn't happen before but I had to Hard Reset the phone as I was having problems with a Bad program.
Thank You for any Help
Stylesclashswanton

BUMP

Similar Messages

RED LIGHT / BATTERY PROBLEM

My blackberry has recently been unable to charge up. I bought a new battery yesterday and all I am seeing is just a red light turning on and off. Please help as I really want to get my blackberry torch up and running

Hi and Welcome to the Community!
Please try this sequence...note that, throughout the entire 4h15m process, your BB must remain connected to a known-good wall charger (not PC USB):
With the battery inside, connect your BB to the wall charger
Leave it alone for 2 hours, no matter what the LED or the display does
Remove the battery
Wait 15 minutes
Insert the battery
Wait another 2 hours, no matter what the LED or the display does
This has been known to "kick start" some BBs.
It is also possible that your battery or BB has experienced a problem...to test, this sequence is needed:
Obtain an known good and already fully charged additional battery...use it in your BB and see what happens
Obtain access to a known good and identical BB...use your battery in it and see what happens
The results of this will indicate if it's your BB or your battery that has the problem. Note that, while rare, a "new" battery certainly can be defective...the best (and least expensive) test method is to find someone with an identical BB who has no issues...trade batteries and see what happens.
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Curve 8520 red light

Hi,can anybody help me my curve has 4 flashing lights i had a look at my battery and found the bottom white sticker had turned pink and 4 red x's on it I replaced the battery with a new one but still have these 4 flashing lights also have carried out an update all seemed good but no luck. Please please can anyone help me. thanx

Hi and Welcome to the Community!
REMOVE YOUR BB BATTERY NOW!!!
Run, don't walk, to this FAQ:
http://www.blackberryfaq.com/index.php/Got_Your_BlackBerry_Wet%3F
Do everything it says, including waiting the maximum recommended time. Applying power to your BB between it getting wet and doing this process reduces the chances of success. Further, the only thing predictable about moisture intrusion into a BB (indeed, any electronic device) is that the results will be unpredictable. I've seen some come back up right away and be fine. I've seen others never work at all. I've seen still others run for a bit, and then die later. And every thing in between.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

BlackBerry Curve 8520, no red light, black screen.

Hi Everyone,
I upgraded my phone to a blackberry cure 8520 about 3 weeks ago, and I haven't dropped it or anything. It has been very well taken care of. Now the screen is completley black, and its plugged in but the red light doesnt turn on and if I try to turn the phone on nothing happens (No White Screen, No Red LIght, NOTHING!) Like i said this phone is not very old, and it was working a couple of hours ago and had almost half of its battery power left. The problem happened after I plugged the blackberry in. It was fine until then. I dont know what to do! Any suggestions?

Hi and welcome to the forums!
Try a battery pull (hard reset) as your first step.
Thanks,
Bifocals
KB02141How to reset a BlackBerry smartphone
"A reset of a BlackBerry® smartphone is a troubleshooting method that completely turns off and restarts the BlackBerry smartphone's operating system software and applications. It is a useful first step if a BlackBerry smartphone is experiencing hardware, software, or wireless network problems."
"Note: A reset of a BlackBerry smartphone does not delete any settings or data."
Click Accept as Solution for posts that have solved your issue(s)!
Be sure to click Like! for those who have helped you.
Install BlackBerry Protect it's a free application designed to help find your lost BlackBerry smartphone, and keep the information on it secure.

HT1567 I can't import an audio cd to itunes to add to my library. I ran a diagnostics test and it had a red light next to: Unable to access audio cd. I am wondering if anyone else has had this problem and if there is an easy solution?

I can't import an audio cd to itunes to add to my library. I ran a diagnostics test and it had a red light next to: Unable to access audio cd. I am wondering if anyone else has had this problem and if there is an easy solution?

Satellite L675-S7113 Specifications (PSK3AU-07C02S)
Satellite L675-S7113 Support Page
rwls wrote:...since I got it 3 years ago I've been unable to burn an audio CD from ITunes or Windows media although it worked once after the computer had been shut off for awhile..and didn't find the problem until after my warranty had expired...
From your statements above, it sounds like you never tried to burn a CD for at least the first year that you owned the laptop, as it had a one year warranty on it. While you might have used it frequently to install software, play DVDs, Blu-Ray disks, etc, that's unclear from your statements. Nonetheless, it might just be dirty-dusty. So, before deleting-uninstalling any software, and given they're cheap, try a CD-DVD Cleaner Disk first and see if that resolves your problems.
Let us know what happens. Good luck.
Mike

I've got a mac pro problem with the starting up, but also a red light on the logic board solidly on. Its not among the diagnostic led. It's located near the BT adapter and the front fans. Also the fans run loud also. any solutions?

Hi
I've got a mac pro late 2006, and i am having problem with it for quite a while now. the problem i am facing is the start up process, and the red light on the logic board. Earlier I've got the two led on the diagnostic leds 5 and 6 turned on without the diagnostic button being pressed, and i think those are related to the processors overtemp. I've managed to solve that by, removing the processors and re applying the thermal compound on the heatsink. what i have left now with is the red light on the logic board at the time i plugged in the power. At the same time when this light come on, the power indicator at the front panel come on as well. i am not sure what is this light relates to. We've replace the power supply too, and gone through the SMC reset but seems no help.
Any idea on the problem? I am desperate about it, and i will be greatful if anyone can help..
thanks and hope for your best solutions
Kari

I can't help directly with your problem but you might check here http://tim.id.au/laptops/apple/macpro/ for a service manual which could answer your question.

Red light headphone jack problem iMac 27" 2011

I have a problem with internal speakers. I searched forums and I think is a problema about the connector, the red light in headphone jack is on. I cannt hear from internal speakers sometimes and now it's allways. I need to plug a headphone or external spekaers to get sound.
I buy the iMac about 2 month ago. May I send the computer to the store or can I fix it?
Regards,
Francisco Mesa

Some solutions to be found in this thread https://discussions.apple.com/message/10384803#10384803
Stefan

Red light problem

I have a red light coming from my headphone jack. In the sound output, the only thing there shows optical digital output, though nothing is there. It started when I dropped the computer, and now the internal sound will not work. I tried to spin the toothpick around, and the red light would turn off for a few seconds, then it would flicker back on. This has happened about 5 or 6 times, so Im not sure if Im doing something wrong or if its a bigger problem.
Thanks!

Please make a Genius Appointment and take it in for service. The red light is related to the optical digital output.

I have a problem with my macbook,if I don't have my earphone plugged, I can't listen anything,and start shine a red light. what should I do?

I have a problem with my macbook,if I don't have my earphone plugged, I can't listen anything,and start shine a red light .what should I do?

try inserting and removing the headphones in and out of the audio jack. The toggle switch is stuck and your mac thinks the headphones are still plugged in.

HT3180 I Have No Power or no red light, has any one else had this problem.

I have no power or no red light, has anyone else had this problem?

I have noted in several posts as have a few of the others here,, Bob Timmons being one who has tested it, that the new one was no better than the old ones. I bought a new AEBS 5th Gen to test against all my old TC's up to Gen 3.. IMHO they are all about the same.. and my old Thomson G wireless router beats them handsomely at the other end of the house. ie the range is to be frank, pathetic. I don't have a Mac laptop to test with.. so just concluded it needs the exact match to get results like anandtech article..
I would do the following.
1. Download and use 5.6 utility.. you are lucky you are still on Lion as ML no longer can use v5 utility.
http://support.apple.com/kb/DL1482
2. Set wireless names to short, no spaces, pure alphanumeric. Set a different name to 5ghz. Its range is always short.. so don't expect too much. Make sure the output is set to 100%.. and the region is correct.
3. Lock the wireless channel for 2.4ghz.. test the available channels.. in Nepal I have no idea what is allowed.. but 1, 6, 11 are the main non-overlapping channels for most of the world. Power output maybe different though and the TP-Link might be set to higher output country.. apple do not allow that. Check what country the tp-link is set to.
4. The location of the TC must be as good as possible.. The antennas are around the 3 sides but the most important is in front.. try to place the TC so the laptop is facing the front of the TC, with nothing in between.
I am pretty sure you are never going to get the output any higher than it is now.. I still use the old wireless G Thomson signal in the other end of the house. And even running 3 TC at once (when I am repairing power supplies.. makes no difference.. they are all invisible).
Either return the TC as unsuitable.. or simply use it as a backup.
The TP-Link can be used in wan bypass to provide wireless.. just turn off the TC wireless.

A strange flashing red light problem on the 8100.

Blackberry Pearl 8100
Problem: Usually after using it for the first time after several hours of non-use it will shut off unexpectedly, flash me the red light twice, and then allow me to turn it back on to a long load up. Battery power is fine. No data loss. No unexpected behavior beyond that.
Should I wipe it?
Any help is appreciated.
Thanks.

I have never seen or heard of a 2008 shipping with, or supporting, 512MB DIMMs, I guess you may try, but then those would be the slower 667MHz FBDIMMs probably, and not 800MHz.
It would have shipped with 2 x 1GB with one on each Riser, but then to install a full set, move one, and install pairs on a Riser.
People have had bad memory show with half its correct amount.

My blackberry curve 8520 is not turning on it shows a red light

My blackberry curve 8520 will not turn on it shows a red light flashes 2x then my keypad lights an thats it nuthing else happens please help me i havent got a usb cable so cant use blackberry desktop manager

Hello Hasanm52,
Welcome to the community!
Seems OS is corrupt, so you have to arrange a USB cable to connect your devci with the pc.
Procedure to install OS:
1.) Download and install blackberry device software of Blackberry 8520 from www.blackberry.com.
2.) Install it in your PC & connect your device with PC.
3.) Access path c:\prog. files\Common files\ Reasearch in motion\ App loader\ now dowble click on loader.exe
4.) Further procedure i very user friendly, so please follow steps (may take approx 90 mins).
5.) In between, it will prompt you to take backup as well, so do take care while clik next or continue.
Good luck..!!!
Before doing above activity you may try
By pulling out battery & connect device with charger without inserting battery & wait for 5 to 10 mins.
Itwill prompt you a no battery sign on your handheld, once you get the sign on your handheld, insert battery without un plugging charger 7 wait for another 5 to 10 mins. Hope this will work for you....
otherwise you have to perform the first procedure, i mentioned...
Thanks....!!

Belgian Problem : Four Red Lights

Hello everyone,
I think the "Four Red Lights on D-Bracket" problem is back... ;(
I have been running a MSI KT3 Ultra with an Athlon XP 1700+ (0,18 µm) coupled with a Thermaltake Volcano 7+ for months now without any problems.
But yesterday my system hung after a few minutes work. As it was the FIRST one I got with this card, I was a little bit surprised but finally thought this could happen even to the best ones...
I simply rebooted but then had to realize there was going wrong with it. My system hangs during the initialisation of my SCSI devices... strange... really strange. I powered off my computer, wait a few minutes and restarted it. And guess what? Black screen with 4 red lights on D-Bracket.
I read the manual and found out that my CPU was wrong. That's really strange because I did not modify anything (no overclocking by the way!)...
I tried to find out what the problem could be by removing unnecessary components (like SCSI adapter card, sound card, network card,...), by clearing CMOS (after I read this nice forum), by re-installing my CPU (with fresh thermal compound) but did not resolve the problem
Another evidence that my system was correctly installed was the temperature I got during the past months : about 38°C
Do you think my motherboard simply died? 8o
Thanks for your help
Doukik
MSI KT3 Ultra (MS-6380E Rev. 1)
Athlon XP 1700+ (0,18)
Thermaltake Volcano 7+
256MB PC2100 DDR-SDRAM CL2.5
Aopen FSP300-60GT 300W Power Supply

I've experienced the four red led lights too. It happened right after I changed the BIOS settings for my CPU internal timing from 'Normal' to 'Ultra'. After I saved the setting, my monitor went blank.
I finally solved it after 2 days. I tried multiple times in clearing the Bios to no avail (5x). So even though MSI says the four led lights is because of a 'damaged or mis-installed proc' it's sometimes not the case.
1. I unplugged the power cable from the PSU
2. I took out the CMOS battery
3. I put the jumper on 'clear' bios.
I went to work for a 10 hour period.
When I got back home, I did the steps below per a forum post I read at work.
4. I press and held the case 'Reset' button for about 30 secs (supposely, it would drain the capacitors)
5. Then I set the Bios jumper back to normal setting.
6. Then I press the 'Reset' button for about 20 more secs.
7. I put the CMOS battery back in.
8. I plugged the power cable backup and crossed my fingers.
I booted up and I still saw four led lights, then the lower right one changed to green and I knew I was in business.
My theory is that somehow, the Bios still retained the 'Turbo' settings when I set the jumpers to clear the Bios multiple times. I think over the period of one day w/ out the battery the BIOS made have defaulted back to the normal settings and/or the addition pressing the reset button drained the capacitor and reset the BIOS.
Sorry the post is so long, but I'm just want to share my experience.
Thanks to all who post and share ideas on these forums!
Take what you deem valuble from each post and combine the ideas to solve your Problem.
cheap 300 watt PC club case came w/ Allied PSU (180 combined)
Atlon Xp 2000+ (133x12.5=1600) (oc at 144x12.5=1800)
2x 256 Kingston ValueRam DDR PC 2700 CL2.5
Elsa 920 Geforce3
MSI KT4 Ultra (MS-6590)

Red light problem 8900

I forgot my password on my phone last week, and i lost all my contacts and that on my phone, since then the red light has stopped working so it doesnt flash when i get messages or emails, the only thing i have yet to set backup on my blackberry is my emails but i can't see this making a difference so that my red light comes on! is there anyway i can get my red light back on? or will it need repairing or something? thanks for your help!

In your profiles > advanced > active profile, make certain that your email settings include for the LED notification to be on.
If it is set on, you can always do a reboot: With the BlackBerry device powered ON, remove the battery a few seconds and then reinsert the battery to reboot.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Red Light and iTunes problems! Please help!

My macbook is a little more than a year old. Just recently a little red light came on inside the headphone jack and the internal speakers will not work any longer.
Well, I searched online and read about the "switch" that sometimes gets thrown off or whatever. I've tried locating this switch with a toothpick and small metal rod, but I can't find it. If I hold the metal rod in a certain way, the light will go off momentarily. And if I hold the headphone jack in a certain way, the internal speakers will work momentarily.
And just recently, iTunes has started acting up. I play a song, and it will play through the speakers. I take the plug to the speakers out of my macbook and plug it back in, and iTunes will not play the song. It states that it is playing, but no sound is coming out of the speakers that had just worked prior to unplugging them. I have to restart iTunes for it to work.
I can't afford to send my Macbook in.
Please Help!
=(

Now, on top of all of this, I have to jiggle the headphone switch around to even get full sound; otherwise sound only comes out of one side
Someone please help
I can neither afford to call Apple, or afford to send my computer in
And it's been a little over a year since I've had it
This is seriously horrible, horrible customer service
I'm extremely disappointed
I've never been rough with my macbook. I take the headphone plug out one day and this happens
Please help!!!

8520 Red Light Youtube Problem

Similar Messages

Maybe you are looking for