[865PE/G Neo2 Series] DRAM Timing is too tightly, Press any key to reset DRAM timing
hello,
i need some help.
I have been using this system for 1 year and 4 months now. A few days ago, when I booted up my computer, the message "DRAM timing is too tightly. Press any key or DEL to reset DRAM timing." appeared before it started detecting hard drive and CD-ROMS. I pressed a key and the computer continued as normal.
This morning, the problem got worse. I started my PC but my screen remained blank. The HDD light and CD-ROM light came on but the power light remained off. I turned off the PC by holding the power switch. When i turned it on again, it was the same situation but the power light started blinking. I turned off the PSU power from my wall socket and waitied about 1 minute. I turned it on again and the power light started blinking again but slower this time. I repeated the on/off steps by using the power button 2-3times. Finally, I tried pressing a few keys on my keyboard and the power light stopped blinking and remained green. I turned the PC on/off again and this time, it succeded in booting up.
And the DRAM messge appeared again.
I was like trying to start a car on a cold day... only after turning the key a few times did the engine start....
I've no idea what is happening here.
My specs are:
Intel P4 3.0C GHZ L2 512KB, FSB 800MHZ, 478 PIN
2x PC400 512MB DDR CL2.5
865PE Neo2-PLS
400W Power supply
Western Digital HDD 120GB SATA
Maxtor 120GB HDD SATA
Maxtor 60GB HDD IDE
DVD Writer
Creative SB Audigy 2 ZS
Leadtek FX5900 LX 128MB
Thanks
Lifehalo
hi,
i smelled a burning smell from my power supply. i am replacing my power supply. i don't know if it was the cause of the dram timing thing.
i'll post here again after i replace my power supply. Thanks!!
Quote from: Thunder on 13-May-05, 21:00:44
When the comp boots up: press the 'delete' key to enter BIOS
Move the marker to 'Advanced Chipset Features' and press enter
Set 'Configure SDRAM Timing by SPD' setting to [Enabled] and press enter press enter
Press F10, and you woulg get the question 'Save changes and EXIT?', Answer 'YES* and press enter.
If this would'nt help, post back here.
Similar Messages
-
This topic has been moved to Overclockers & Modding Corner.
[865PE/G Neo2 Series] Desperation - Help O/C 865PE-NEO2-LS w/2.8Ghz P4 Northwood - Just won't goThis topic has been moved to Overclockers & Modding Corner.
[865PE/G Neo2 Series] Desperation - Help O/C 865PE-NEO2-LS w/2.8Ghz P4 Northwood - Just won't go -
MSI 875P FISR - 'DRAM timing is too tightly so reload timing'
'DRAM timing is too tightly so reload timing'
I recently got this message upon bootup. I have an MSI 875 P and I have 2 Gigs of Kingston RAM. I am wondering what would cause this message to come up out of nowhere. I was had the DRAM Timing by SPD Enabled and since that didn't seem to work I disabled it. I set the CAS, RAS, and CAS to RAS to 3 - 3 - 3 respectivly as listed below on the manufacturers web page located at:
http://www.ec.kingston.com/ecom/configurator/partsinfo.asp?ktcpartno=KVR400X64C3AK2/2G
My Current Settings Are:
CAS# Latency - 3 Clocks
RAS# Precharge - 3 Clocks
RAS# to CAS# Delay - 3 Clocks
Precharge Delay - 8 Clocks
Burst Lenght - 4
DRAM Integrity Mode - Disabled
--MY RAM--
RAM: KVR400X64C3AK2/2Gl
Description: 2GB Kit 400MHz DDR PC3200 DIMM 3-3-3
Specifications: Standard 128M X 64 Non-ECC 400MHz 184-pin Unbuffered DIMM (SDRAM-DDR, 2.6V, CL3, Gold) (Datasheet)
--Motherboard Manual DRAM Info--
Configure DRAM Timing by SPD
Selects whether DRAM timing is controlled by the SPD (Serial Presence
Detect) EEPROM on the DRAM module. Setting to Enabled enables the
following fields automatically to be determined by BIOS based on the
configurations on the SPD. Selecting Disabled allows users to configure
these fields manually.
DRAM CAS# Latency
This controls the timing delay (in clock cycles) before SDRAM starts
a read command after receiving it. Settings: 2, 2.5 (clocks). 2 (clocks)
increases the system performance the most while 2.5 (clocks) provides
the most stable performance.
DRAM RAS# Precharge
This item controls the number of cycles for Row Address Strobe
(RAS) to be allowed to precharge. If insufficient time is allowed for
the RAS to accumulate its charge before DRAM refresh, refreshing
may be incomplete and DRAM may fail to retain data. This item applies
only when synchronous DRAM is installed in the system. Available
settings: 2 clocks, 3 clocks, 4 clocks.
DRAM RAS# to CAS# Delay
When DRAM is refreshed, both rows and columns are addressed
separately. This setup item allows you to determine the timing of the
transition from RAS (row address strobe) to CAS (column address
strobe). The less the clock cycles, the faster the DRAM performance.
Setting options: 2 clocks, 3 clocks, 4 clocks.
DRAM Precharge Delay
This setting controls the precharge delay, which determines the timing
delay for DRAM precharge. Settings: 5 clocks, 6 clocks, 7 clocks, 8
clocks.
DRAM Burst Length
This setting allows you to set the size of Burst-Length for DRAM.
Bursting feature is a technique that DRAM itself predicts the address
of the next memory location to be accessed after the first address is
accessed. To use the feature, you need to define the burst length,
which is the actual length of burst plus the starting address and
allows internal address counter to properly generate the next memory
location. The bigger the size, the faster the DRAM performance.
Available settings: 4, 8.
DRAM Integrity Mode
Select ECC (Error-Checking & Correcting Code) or Disabled according
to the type of DRAM installed.
I am wondering if something else could be interfearing with the ram such as the AGP slot/card or if this is strictly a RAM issue. I have not seen this message before. Are my current settings what they should be for this RAM? Should I be asking Kingston this instead of coming here?Thanks for the response.
My current DDR Power Voltage is set to 2.70.
Do you think 2.75 would be better? I'm wondering why you suggest 2.7 or 2.75, now that I look at the RAM specs it actually says 2.6 as posted above. I am not trying to be a jerk, I am just curious and want to know more!
My AGP Power Voltage is set to 1.50. I have a BFG Geforce 6800 GT OC 256 MB. I'm wondering if changing this a bit might help my graphics card as well? Perhaps 1.55 or 1.60V? -
[865PE/G Neo2 Series] I Messed Up My Computer Really Bad
Wow. Where to begin.
I was in my BIOS looking at DRAM timings and Frequencies... noticed that there for DDR500 it had (4:5), which I presume means the RAM runs out-of-sync with the processor. I tried it out to see what it would do.
Well, my computer wouldn't boot. And it wouldn't revert back to default BIOS settings which it normally does when I set something in the BIOS that it doesn't like. And I thought the appropriate course of action in this situation was to reset the CMOS battery. Evidently it was not the right thing to do, because it screwed everything up royally.
After resetting, I booted up and saw some CoreCell logo which I've NEVER seen before, ever. Instead of going to the screen which shows the Energy Star logo and lists all my hardware being checked, it goes to a couple lines saying something about Realtek Gigabit Ethernet controller. It busies itself for a few seconds, then says 'Boot Failed. Insert Boot Disk and press any Key'. Uh-oh.
I restart and try to get into my BIOS. It gives me options of either press F1 to go into Setup or F2 to Load Defaults or some damn thing. Eventually I get into the BIOS and its blue instead of red, like it always has been. All my options are obliterated - it doesn't even list any hard drives anywhere. Evidently it isn't recognizing either of my hard drives. I go into my motherboard manual and find the section about On-Chip IDE configuration. I don't even remember what the hell these settings were on before I screwed everything up. ATA Configuration was on PATA Only, SATA Keep Enabled was set to No. I don't know why because both of my drives are SATA.
I try setting SATA Keep Enabled to Yes, then reboot. It boots, and I'm finally here back in Windows. My system clock was five years off, but my data is here. It also detected some new Audio Hardware, but i just canceled.
Good god, someone please help me out here. I'm afraid to even shut off my computer or even mess with anything for fear of not even being able to get back into Windows.OK, I went into the BIOS and put everything back to how it should be. A few things were strange though:
The order of the devices in Standard CMOS Features is different then it used to be. Before, the DVD drive was Primary IDE Master, the CD-RW the Primary IDE Slave, my boot HDD was Third IDE Master and my data HDD Fourth IDE Master. Now, my boot HDD is Primary IDE Master, data HDD is Secondary IDE Master, DVD Drive is Third IDE Master and CD-RW is Third IDE Slave.
Some of the voltages and frequencies were set to strange values. I thought the default AGP voltage was 1.5 and DDR voltage default 2.5. When I went into the BIOS the AGP voltage was 1.7 and the DDR Voltage 2.75. Before this all happened I had them set at 1.6 and 2.8 respectively. I changed them to those values and it booted fine. The 1.7 in particular worried me a little, because I remember reading somewhere that upping AGP voltage too far can do nothing but harm.
Its still a blue screen instead of red. I know this is trivial, but when the color's different, one tends to think that some setting is different, or the version is different, somehow. There isn't any background color setting in the BIOS that I know of.
I know I was overreacting a little, but it was too late at night and all I could think of was how I couldn't access the ten-page research paper that's on my hard drive, due in a couple days. -
[865PE/G Neo2 Series] 865 PE Motherboard problem?
I have MSI 865 PE neo 2 MB,intel pentium 4 2,6C HT,and recently I have flashed it's bios with a new one,the new bios said that it can reduce the CPU temperature.I have flashed it carefully,follow the faqs and everything seems alright.The problem is I used corsair cmx-256C2,the reference say that it's can run in CL 2(2-3-3-6) and after I flashed the bios my memory run in 2.5-4-4-8(the default timing from the mother board) and when I change to 2-3-3-6 the system won't startup,it says the timing is too tight .I didn't find this problem with my old bios,and I doesn't want to change back the bios to the old one,because the temperature differences is to high(with old bios CPU idle=47 degrees,new bios = 38 degrees)
Anyone know how to solve the problem?
ThxSo the new bios did'nt change the CPU temperature but just only correct the temperature report?oh my....
I flashed it using Live Update 3,and I am forgot to save my old bios,so where I can find the old bios for my MB.It seems the MSI website didn't provide it.
And why did MSI releasing new bios while stil have defect on it to the customer?it can make unexperience user (including me) dissapointed when knowing it.
Oh by the way,I bought the MB about 2 years ago and I am satisfy with the performance and stability( I am using it about 21 hours a day),and I still planed to use it.
And why my Mb didn't have onboard lan,I saw in the website the other had.I have added it later and cost me $10. -
[865PE/G Neo2 Series] Suggestions for excellent Air/Fan Cooling - P4 Northwood
Guys, I need some advice here. I've got my 2.8 Northwood up to 3.16 (yea, I know, not great or anything but good enough for right now).
Anyway, with the coming of the blazing Summer temps hitting Michigan in the high 80-90s, my case and CPU temps are skyrocketing. I am finding that my idle temps, once at 31C are now at 35-36C, and the CPU temps once at 42C max under load are now reaching 50+ C. Also, this is the first time in months upon seemingly endless months that I am now getting random reboots, and I am sure it is due to soaring temps and heat problems. The room temps here are killer, and right now are in the high 70s...
I would like to please hear your suggestions/recommendations on a good AIR/FAN cooling solution for my specs I have listed below. I am looking for something that is not very loud if possible, I welcome and thank you for your comments!
865PE-NEO2-LS (601-6728-020)
AMI BIOS version 2.5
P4 Northwood, Socket 478, 2.8 Ghz/800Mhz FSB HT Enabled
4 DIMMS (256MBx4)=1GB KingMax PC3200 DDR400, Model # MPXB62D-38KT3R-PEA
PowMAX PS LP-8800D, 400 watt, max load +3.3@28A,+5@30A,+12@25A,[email protected],[email protected],+5vsb@2A, 70% min@full load
INTEL 865 .INF Drivers (6.0.1.1002 5/7/2004)
Main: Western Digital Raptor, 10K rpm, 36GB
2nd: Maxtor ATA133 7200rpm 120GB
CD-RW: Lite-On 52x32x52
BFG Tech GeForce 6800 GT OC 256MB GDDR3 AGP Graphics Card
SoundBlaster Audigy 2
ViewSonic Professional P225FB 22" monitor
Current Settings:
Configure SDRAM Timing by SPD Disabled
CAS# Latency 3
RAS# Precharge 4
RAS# to CAS# Delay 4
Precharge Delay 6
Burst Length 8
AGP Aperture Size 128
FREQUENCY/VOLTAGE
Performance Mode (slow, fast, turbo, Ultra Turbo) SLOW
DRAM Frequency 452
Adjust CPU Bus Clock (Mhz) 226
DDR Clock (Mhz) 452
Adjust AGP/PCI Clock (Mhz) 66.66/33.33
CPU Vcore Adjust Yes
CPU Vcore 1.5375
DDR Power Voltage (Default is 2.50) 2.6500
AGP Power Voltage 1.5000
SiSoftware Sandra Prof. 2005 System Info
Front Side Bus Speed (4x)/Memory Bus Speed (2x) 226
Front Side Bus Data Rate (FSB Speed x4) 904
Memory Bus Speed (FSB Speed x2) 452
CPU SPEED (GHz with 14x multiplier) 3.16
CrystalCPUID 4.4.5.253 (C) 2002-2005 hiyohiyo
Crystal Dew World [http://crystalmark.info/]
OS : Windows XP Professional SP1 [ 5.1 Build 2600 ]
Date : 2005/06/08 0:48:10
CPU Name : Intel Pentium 4 HT (Northwood)
Vendor String : GenuineIntel
Name String : Intel(R) Pentium(R) 4 CPU 2.80GHz
Architecture : x86
Process Rule : 0.13 um
Platform : Socket 478 [2]
CPU Type : Original OEM processor
Number(Logical) : 2
Hyper-Threading : 2
Family : F
FamilyEx : 00
Model : 2
Stepping : 9
APIC : 00
Brand ID : 09
Microcode ID : 14
Feature : MMX SSE SSE2 HTT
PowerManagement :
Current Original
Clock : 3164.35 MHz 2800.00 MHz
System Clock : 226.03 MHz 200.00 MHz
System Bus : 904.10 MHz 800.00 MHz
Multiplier : 14.00 14.00
Data Rate : QDR
Over Clock : 13.01 %
L1 T-Cache : 12 KuOps
L1 D-Cache : 8 KB
L2 Cache : 512 KB [Full:3164.35 MHz]
Memory : 1024 MB
CPUID : EAX EBX ECX EDX
00000000 : 00000002 756E6547 6C65746E 49656E69
00000001 : 00000F29 01020809 00004400 BFEBFBFF
00000002 : 665B5001 00000000 00000000 007B7040
80000000 : 80000004 00000000 00000000 00000000
80000001 : 00000000 00000000 00000000 00000000
80000002 : 20202020 20202020 20202020 6E492020
80000003 : 286C6574 50202952 69746E65 52286D75
80000004 : 20342029 20555043 30382E32 007A4847
MSR : EAX1 EDX1 EAX2 EDX2
: 00000080 00000000 0E12000E 00000000
QPF : 3164.350000 MHz
Chipset Information
Chipset : Intel 865G/PE/P/848P (Springdale-G/PE/P)
North Bridge : [8086:2570.02] Intel 82865G/PE/P/848P
South Bridge : [8086:24D0.02] Intel 82801EB/ER (ICH5/R)
Video Chip : [10DE:0045.A1] NVIDIA GeForce 6800 GT (NV40)
BIOS Information by WMI (Windows Management Interface)
BIOS Vendor : American Megatrends Inc.
BIOS Caption : Version 1.00
BIOS Version : AMIINT - 10
BIOS Date : 09/29/2004
SM BIOS Caption : V2.5
SM BIOS Version : 2.3
Mother Vendor : MICRO-STAR INC.
Mother Product : MS-6728
Mother Version : 100
System Vendor : MICRO-STAR INC.
System Model : MS-6728
System Information by DMI (Desktop Management Interface)
SM BIOS Version : 2.3
BIOS Vendor : American Megatrends Inc.
BIOS Version : V2.5
BIOS Date : 09/29/2004
BIOS ROM Size : 512 KB
Mother Vendor : MICRO-STAR INC.
Mother Product : MS-6728
Mother Version : 100
CPU Socket : FC-478
CPU Vendor : Intel
CPU Version : Intel(R) Pentium(R) 4 Processor
Current Clock : 3164 MHz
External Clock : 226 MHz
Max Clock : 4000 MHz
Quote from: swambast on 08-June-05, 12:54:14
Guys, I need some advice here. I've got my 2.8 Northwood up to 3.16 (yea, I know, not great or anything but good enough for right now).
Anyway, with the coming of the blazing Summer temps hitting Michigan in the high 80-90s, my case and CPU temps are skyrocketing. I am finding that my idle temps, once at 31C are now at 35-36C, and the CPU temps once at 42C max under load are now reaching 50+ C. Also, this is the first time in months upon seemingly endless months that I am now getting random reboots, and I am sure it is due to soaring temps and heat problems. The room temps here are killer, and right now are in the high 70s...
I only know that I can't suggest a HS and fan because my temperature is higher than my 2.6GHz Northwood's since i decided to install the Thermalright XP90 and the 92mm UFO Thermaltake fan(~82CFM max.). I recently discovered an old picture from Speedfan saying CPU temp: 40C!!! Now right after boot up, I get 40-44C idle and it can climb up to 60C at full load. I know for a fact that air flow is bad inside the case but it's unbelievable to have 40C+ idle. It can't possibly be the air flow so soon after boot. The pressure (and contact) on the CPU was enough to actually see my CPU stuck on the base of the HS after removing the HS!!! A few pins had to be straightened too.
So, from my experience I think you already rock, since we have 30C(86F) already where I live. The feeling of the XP90 crashed under my boot will ease my pain...Oh, yes it will.
P.S. I 'll give the Arctic Silver a try before smashing the XP90 junk...
P4 2,6GHz Northwood
MSI Neo2-PFS 865PE (v3.2 AMIBIOS)
1 GB RAM PC3200 Kingston & TwinMOS
WD 800JB 80GB-7200RPM
CLUB ATI Radeon 9600Pro
Creative Audigy2 ZS -
Hi,
I have a problem fitting a Zalman (CNPS7000B-Cu) cpu cooler - the MSI northbridge sink is too high and too close to the cpu.
Can I replace the NB sink with one with a lower profile?
( Incidently, I'm not overclocking, although I do use this machine as an audio machine and it does get quite hot.
- If I can replace - any recommendations?
- If not - any recommendations for a reasonably priced and quiet cooler that will fit (i.e with a narrow profile).I had the same problem on my 865PE Neo2-PFS Platinum Edition mobo. Zalman's website indicated that the CNPS7000a-AlCu fits on this board, but it doesn't. The diagonally placed northbridge heatsink is in the way. I originally thought I'd bend a few of the Zalman's fins out of the way, but then I decided if I could do something with the northbridge heatsink. I removed the northbridge heatsink and removed the 2 fins that were in the the way of the Zalman. I wanted to repalce the modded northbridge heatsink using some AS5 but the stock thermal goo (some pink stuff) was impossible to get off, even with alcohol or acetone. So I smeared some AS5 on anyway and just mooshed the heatsink back on with the pink junk and AS5.
I noticed that the northbridge gets really hot at stock speeds (200 FSB). I'm planning on overclocking my 2.4C to 3GHz (250 FSB) today, so I hope the northbridge doesn't burn up. Gonna aim a fan at it and hope for the best.
Hope the "bend 2 fins off the northbridge heatsink mod" helps all you guys that want to put Zalman's on your CPU's.
-Coelacanth -
[865PE/G Neo2 Series] Memory timings and power settings anyone?
I'm not very good with computers, so I've just played around with the timings on my memory, but have not found one stable setting as of yet.
The memory is brand new and I've tested it for errors on my brothers computer and there's nothing wrong there.
Intensive harddrive usage, dvd playing and intense downloading while listening to music are sure ways to crash my system. "..........Not less or equal" is the most common error message, but there are
many many more.
Oh, maybe I should point out that overheating's not an issue, cause I've good fans and run my computer without sidepanels.
I also like to say that I have the first generation of p4 with ht and 533fsb.
I'm sure there's something I forgot to mention but here below I'll paste the system summary that Sandra gave me.
Would be forever grateful if someone could help me out with the memory timings and power settings for my board. Setting it to "auto by spd" gives me a very unstable system, so no avail there.
I'm running the mem at 2.70 and sometimes at 2.65, since these two settings seem to be the ones with least crashes.
The Memory installed are 4*512mb ,kingston 512 kvr333x64c25 pc2700
The PSU is a Tagan "TG480-u01" 480w
Many many thanks in advance guys.
SiSoftware Sandra
Processor
Model : Intel(R) Pentium(R) 4 CPU 3.06GHz
Speed : 3.10GHz
Performance Rating : PR4118 (estimated)
Cores per Processor : 1 Unit(s)
Threads per Core : 2 Unit(s)
Internal Data Cache : 8kB Synchronous, Write-Thru, 4-way set, 64 byte line size
L2 On-board Cache : 512kB ECC Synchronous, ATC, 8-way set, 64 byte line size, 2 lines per sector
Mainboard
Bus(es) : ISA AGP PCI IMB USB FireWire/1394 i2c/SMBus
MP Support : 1 Processor(s)
MP APIC : Yes
System BIOS : American Megatrends Inc. V2.5
System : MICRO-STAR INC. MS-6728
Mainboard : MICRO-STAR INC. MS-6728
Total Memory : 2GB DDR-SDRAM
Chipset 1
Model : Micro-Star International Co Ltd (MSI) 82865G/PE/P, 82848P DRAM Controller / Host-Hub Interface
Front Side Bus Speed : 4x 135MHz (540MHz data rate)
Total Memory : 2GB DDR-SDRAM
Memory Bus Speed : 2x 168MHz (336MHz data rate)
Video System
Monitor/Panel : Iiyama A201HT VisionMaster Pro 510
Adapter : RADEON X800 Series
Adapter : RADEON X800 Series Secondary
Imaging Device : CanoScan FB630U/FB636U #2
Imaging Device : Video Blaster WebCam 3/WebCam Plus (WDM) #2
Physical Storage Devices
Removable Drive : Diskettenhet
Hard Disk : ST3160023AS (149GB)
Hard Disk : WDC WD1000BB-00CAA0 (93GB)
Hard Disk : WDC WD1200JB-00CRA1 (112GB)
Hard Disk : FUJITSU MPG3409AT E SCSI Disk Device (38GB)
CD-ROM/DVD : PHILIPS DVDR1640P (CD 63X Rd, 63X Wr) (DVD 8X Rd, 8X Wr)
CD-ROM/DVD : PLEXTOR CD-R PX-W4824A (CD 40X Rd, 48X Wr)
CD-ROM/DVD : AXV CD/DVD-ROM SCSI CdRom Device (CD 32X Rd) (DVD 4X Rd)
CD-ROM/DVD : AXV CD/DVD-ROM SCSI CdRom Device (CD 32X Rd) (DVD 4X Rd)
CD-ROM/DVD : AXV CD/DVD-ROM SCSI CdRom Device (CD 32X Rd) (DVD 4X Rd)
CD-ROM/DVD : AXV CD/DVD-ROM SCSI CdRom Device (CD 32X Rd) (DVD 4X Rd)
CD-ROM/DVD : AXV CD/DVD-ROM SCSI CdRom Device (CD 32X Rd) (DVD 4X Rd)
Logical Storage Devices
1.44MB 3.5" (A:) : N/A
Hard Disk (C:) : 149GB (101GB, 67% Free Space) (NTFS)
Xp (D:) : 112GB (2.1GB, 2% Free Space) (NTFS)
Big (E:) : 93GB (9GB, 10% Free Space) (NTFS)
Jimjimjim (F:) : 38GB (2.1GB, 5% Free Space) (NTFS)
Bologna_2 (G:) : 3.9GB (UDF)
CD-ROM/DVD (H:) : N/A
Bfv_3 (I:) : 486MB (CDFS)
Doom 3 roe (J:) : 650MB (CDFS)
Sims2ep1_1 (K:) : 650MB (CDFS)
Bf2 dvd (L:) : 1.9GB (UDF)
CD-ROM/DVD (M:) : N/A
Peripherals
Serial/Parallel Port(s) : 1 COM / 0 LPT
USB Controller/Hub : Intel(R) 82801EB USB Universal Host Controller - 24D2
USB Controller/Hub : Intel(R) 82801EB USB Universal Host Controller - 24D4
USB Controller/Hub : Intel(R) 82801EB USB Universal Host Controller - 24D7
USB Controller/Hub : Intel(R) 82801EB USB2 Enhanced Host Controller - 24DD
USB Controller/Hub : Intel(R) 82801EB USB Universal Host Controller - 24DE
USB Controller/Hub : USB-rotnav (hub)
USB Controller/Hub : USB-rotnav (hub)
USB Controller/Hub : USB-rotnav (hub)
USB Controller/Hub : USB-rotnav (hub)
USB Controller/Hub : USB-rotnav (hub)
USB Controller/Hub : USB-enhet (sammansatt)
USB Controller/Hub : Stöd för USB-skrivarport
FireWire/1394 Controller/Hub : OHCI-kompatibel IEEE 1394-värdstyrenhet
Keyboard : Logitech HID-Compliant Keyboard
Keyboard : HID-tangentbordsenhet
Mouse : HID-compliant MX310 Optical Mouse
Mouse : HID-kompatibel mus
Mouse : HID-kompatibel mus
Human Interface : Logitech WingMan Force 3D USB (HID)
Human Interface : HID-kompatible konsumentkontrollenhet
Human Interface : HID-kompatibel enhet
Human Interface : Logitech Virtual Hid Device
Human Interface : Logitech Virtual Hid Device
Human Interface : Logitech USB MX310 Optical Mouse
Human Interface : Logitech WingMan Force 3D USB
Human Interface : USB HID (Human Interface Device)
Human Interface : Internet Keys USB
MultiMedia Device(s)
Device : Audigy X YouP-PAX A4 v1.00 Audio Driver(WDM)
Device : Creative Game Port
Device : Pinnacle PCTV Stereo PAL Capture Device
Printers and Faxes
Model : Microsoft Office Document Image Writer
Model : Canon PIXMA iP4000
Model : Adobe PDF
Power Management
AC Line Status : On-Line
Operating System(s)
Windows System : Microsoft Windows XP/2002 Professional (Win32 x86) 5.01.2600 (Service Pack 2)
Network Services
Adapter : Intel(R) PRO/1000 MT Desktop Adapter #2Thanks for your answers.
Danny: 1. Yes, I've put my memory in my brothers computer, and ran memtest there, and it came out ok, but on mine it crashes almost instantly.
2. Yea, I have 2 fans blowing into the case and one out, so airflow is good, cpu is also cool and seems to be happy ;-)
Geps: I can't say I understand all these numbers but there are som specs here as an example, Tagan TG480-U01 480W ATX
I can't imagine that this psu ain't enough, and if so.....I've been had by the dealer. -
[865PE/G Neo2 Series] DDR Memory with 865PE Neo2-PFS Platinum
SYSTEM SPEC: 400w PSU, Pentium 4 3.2ghz 800mhz FSB (HT), Matrox Parhelia 128 8x AGP card, MSI Neo2 PFS Platinum motherboard.
Hi there. Im looking for some serious help with my computer. I have a MSI 865PE Neo2-PFS Platinum mobo and have been using 512mb DDR RAM with it- the ram is PC2700 (333mhz), non-ECC, ubuffered, non-parity, 184 pin. Now, I have just purchased a new DIMM. This one is
1gb PC3200 (400mhz), non-ECC, Unbuffered, non-parity, HIGH DENSITY- DUAL IN LINE, 128 x 64, 184 pin
It doesnt work and my system refuses to boot up. I checked out the specs of the 865PE Neo2-PFS Platinum, and it says in the table that you can only use 400mhz DDR RAM with an 800mhz FSB processor (which I have). It says it supports 400mhz RAM, "DUAL CHANNEL", non-ECC, unbuffered memory, but no mention of "HIGH DENSITY" or "DUAL IN LINE". Is there a difference between "DUAL CHANNEL" and "DUAL IN-LINE". Also, does anyone know what the difference is between 128 x 4 and 128 x 64, they are both 1gb? SOMEONE PLEASE HELP!!! I have seen some RAM from the same dealer which is not "HIGH DENSITY" and has the 128 x 4 configuration, and is still a 1gb module. Is that safe to buy? What RAM do I need (in detail) for my motherboard. Thanks!Always useful with a complete systemspec.including PSU and biosversion, so please make one.
Can´t see anything wrong with the basic RAM specification - it also matches the MoBo basic specifications:
- Supports four unbuffered DIMM of 2.5V DDR SDRAM.
- Supports up to 4GB memory size without ECC.
- Supports Dual channel DDR266/333/400/433/466/500/533 MHz and up.
Have you tried removing the old RAM and booting only with the new 1GB stick alone ?
Using mixed RAM, sometimes works in "Single mode" (see mobo manual), but is not recommended.
Running Dual-channel ( 2x512 or 1024x2 ) is preferable and gives best performance, but then you need two identical sticks.
You may also need to increase RAM voltage some in bios (example 2.7v) to achieve best stability.
If you have some RAM compability issues with 1GB sticks - 2x512 RAM stick would be safer and give better performance, unless your aiming for more then 2GB in total.
You can also read about the RAM testreport here;
http://www.msi.com.tw/html/products/mainboard/testreport_pdf/6728v2.0/memory.pdf
About "Dual In line Memory Module" - I think it´s the long version for older DIMM description.
Just like "Double Data Rate" is the long version for DDR RAM.
DDR means Double Data Rate RAM (in opposition to the SDRAM or Single Data Rate). DDR RAM bends the transfer rate for clock cycle. It can go quicker because it executes 2 instructions for cycle of clock of the RAM instead of an only instruction like it is the case of the SDR. -
[865PE/G Neo2 Series] Question-boot from Promise IDE on 865PE Neo2 FIS2R
I bought my first MSI board a couple of years ago, an 865PE Neo2-LS. When I retired that, I went for an Abit 875P IC7-G. I just hated the Abit board, used it 3 months and replaced it with a new MSI 865PE Ne02 FIS2R.
I didn't reinstall WIndows XP Pro with the new motherboard. Everything seemed to be OK until I could get around to a clean install of XP. One reason I wanted the FIS2R model was that I wanted to use the faster Promise IDE connection for my boot drive. I had a heck of a time getting the drive to boot, but it finally worked. I was having a few problems that I thought a repair reinstall of XP might solve. So, I tried that yesterday.
Now I cannot get the same drive to boot from the Promise IDE controller. I saw that setting were changed in the BIOS and I can't figure out how to set them so I can boot from the C: drive on the Promise. It will boot fine from the regular primary IDE controller, but I want to use that for two other hard drives I use for storage. The secondary IDE connection is for a CDRW and DVDRW drives.
I've looked at the FAQs and read the manuals. How do I just use the IDE on the Promise? What should my BIOS settings look like? The Promise drivers are installed on the boot drive, the system will post and I'll see a flash of the Windows XP intro screen, then a flash of a blue screen and it kicks it back to booting again. I've never been able to see what that blue screen is telling me. THe drives I want to put on the Promise controller are PATA drives, I don't want SATA or RAID, just using the Promise as a third connection for IDE drives.
Thanks for any help anyone can offer. I have tried every imaginable way of setting the BIOS, but can't seem to hit the right combination. That's what I did on my first try when I got it working, hit a lucky combination and it worked.Thank you. I had already tried the settings in the post you linked to. I had no luck there. I've reinstalled the Promise drivers, but the boot drive refuses to go past the Windows flash screen before resetting. I think it's quite simple what I'm trying to do. I have six drives. On IDE 1 I want to two storage drives to be connected. On IDE 2 I'm putting the Cd and DVD optical drives. On IDE 3 (Promise) I would like to have my boot (master) drive and a slave drive. Rearranging cables I can get the drive to boot from IDE 1, but no luck with IDE 3. I think it's the Promise drivers, they appear to be installed, but I don't think they are working. I'm going to copy the Promise drivers to a floppy and reinstall XP with the boot drive on IDE 3 and see if I get anywhere with that.
The link referred more to SATA and RAID setup, I just want to use the Promise IDE. I'd sure hate to have to put the awful Abit IC7-G back in my system as I can only get 5 IDE devices in that one instead of the 6 the MSI should run. -
[865PE/G Neo2 Series] Help!! Strange DLed combination
Hi all, I ll be quick...
I've got a MSI neo2 PFISR, when I was editing video with a pinnacle pctv, my comp crashed. Ive reseted and nothing, no beeps, nothing at all. The DLED shows: 1- red 2- red 3- orange 4-OFF!!!!. I know its not supposed to be off, but it has changed today, yesterday it was: 1- orange 2- red 3- red 4- orange. Please help...!!!
My spec's when ive get the problem were:
p4 2.4c (fsb800 512k cache)
2 OEM dimm's ddr400 512mb each
1 powercolor ati 9800se@pro
seagate 7200.7 40gb IDE
MSI Neo2 Pfisr
Pinnacle pctv (Multimedia board)
Thanks for ur help.
PS: Ive found that the d bracket was inserted wrongly in the pins inside. Thats why the 4 led was off But the 1- orange 2- red 3- red 4- orange is still on and don't kno what it is. HELP! xDHi,
Re-seat CPU........... (Or too much paste on......... contact thin is best)
Del UK -
[865PE/G Neo2 Series] RAID 1 on 865 NEO2-LS
Hi.
I'd llike to know if it is possible to configure RAID 1 on MSI 865PE Neo2-LS. Originally I think it wasn't possible but on the bios updates there is this note (version 1.5, updated on 2003-9-8): "Add Intel ICH5 RAID1 function."
So does anyone know if it is possible? If so, can you give me a link on how to or any kind of hints?
Thank you.The LS uses the ICH5 chipset. The ICH5R is required for raid. The note refers that the original bios was raid 0 only.
You can always buy a PCI SATA raid card. -
Hi,
i have big problem with my MS-6728 (865PE Neo2-S) and Geforce 4 Ti 4200.
After installing Intel inf update for chipset my Windows XP Pro SP1 stop booting and freeze (if i use Detonator 61 or higher) or just use standart VGA driver (if i use Detonator version 41).
If i remove Intel chipset (i tried all versions) - video is working good
Why Intel Inf update chipet drivers have conflict with my video card ?Hi,
i did as You say - remove Windows XP, format my HDD, installed again Windows XP, installed Intel Inf update - system Ok
install video drivers - freeze and crush.
Nothing help ....
I found on this forum that some people have problem with video like me. they talk about bad agp port driver.....
What can i do now ? -
[865PE/G Neo2 Series] HELP Please? 865PE Neo2 3.0 HT Engineering Sample
I just recently purchased a Neo2 865pe motherboard. I have a Engineering sample 3.0ht 800mhz proc. I used my ES proc from my asus runnin 3.2ghz@800mhz. I install the proc into the MSI and it came up with 1.6ghz. So I tried to up the cpu multiplier it starts from rang e15x and goes to 21x, but even if I set it to 21x I only still get best 2.25mhz. Can someone please point me to a solution. Thank you.
Engineering Samples are like Test beds CPU, which means that it may not work with all boards.
Like what Wonk has mentioned,increased your FSB from 100MHz to 200MHz with Multiplier of x16 and DDR RAM to be clocked at only 400MHz to obtain the 3.2GHz clock of your CPU. -
Hi There,
I have just updated the flash on my computer thru the LiveUpdate running on windows 2000 (without a floppydisk),... the flash ran thru without error and rebooted,... then i ran thru the BIOS settings and came to Frequency/Voltage Control,... BLIP said the computer and then i saw the CPU Voltage (V) saying = ╕65¤ ┐ (not really this sign: ¤ but it is as close as i can get it tiny o with a line on top and buttom of it)
However the system seems (so far (still with the SATA shutdown problem) ) be working fine,... as long as i keep CPU Vcore Adjust on NO,...
I tried reflashing the system,.. same result, i tried coldbooting,... same thing,...sorry bout the "hijacking" thingi .....i am a newbie...sorry again...i already start a new topic ...thankss 4 your all help bye... come join in if u can helpthanks
me...i relly need some help ...
motherboard - MSI 865PE neo-2 Platinum edition...processor - P4P (Presscott) Pentium 4E 90nm 2.8 - 4GHz 1.25 - 1.40v...bought from U.S.A....
3d card - MSI GeforceFX5200 128mb....
RAM - 512 ddr333...
Optical drive - LG CD writer, Samsung DVD rom...
Floppy Drive - samsung normal Floppy drive
chasis - normal ATX icute Chasis....added 2 120x120x25mm fan an a 80x80x25 mm fan.....
Power supply - normal power supply....
monitor - Prolink 17inch
cpu cooler - Cooler Master Hyper 48(KHC-L91-U2)
3d card cooler - Cooler Master CoolViva(VHC-L61)
thanks
i relly need some help ...
Maybe you are looking for
-
Home Sharing stops working with fast user switching
I have a late 2013 iMac running Mavericks. The main account has my iTunes library with Home Sharing enabled. The AppleTVs and IOS devices can see the Home Share and it works well. But, it stops working when user accounts are accessed on the Mac.
-
Help! .TMIB service not returning local attributes
I've the following src to create a an FML request buffer with TA_FLAGS set to MIB_LOCAL... FBFR32* buf = (FBFR32*)tpalloc("FML32", NULL, 1024); Finit32(buf, Fsizeof32(buf)); long flags = MIB_LOCAL; Fchg32(buf, TA_OPERATION, 0, "GET", 0); Fchg32(buf,
-
Wire Hanger out of the Headphone jack?
Think this will give my iPhone at least 1 or 2 bars? Maybe I should wrap it in aluminum foil...that won't take away from the looks at all, will it? I will say, I have one heck of a iPod sitting here
-
Macbook sound issue after standby
Hello, Bit random issue here.. This is not consistence but it is totally random. Randomly when i open the macbook lid when it comes out off standby by i hear a weird "ripping" sound issue i think its coming from left hand speaker or side. Im assuming
-
My Laptop runs Windows 7 and my E Mail is Yahoo, along with Mozilla Firefox if I can install it without problems. My Desktop which I am on now is XP Please can you help and suggest a site for me I have Firefox on my Desktop with no problem I do not w