[865PE/G Neo2 Series] RAID 1 on 865 NEO2-LS

Hi.
I'd llike to know if it is possible to configure RAID 1 on MSI 865PE Neo2-LS. Originally I think it wasn't possible but on the bios updates there is this note (version 1.5, updated on 2003-9-8): "Add Intel ICH5 RAID1 function."
So does anyone know if it is possible? If so, can you give me a link on how to or any kind of hints?
Thank you.

The LS uses the ICH5 chipset. The ICH5R is required for raid. The note refers that the original bios was raid 0 only.
You can always buy a PCI SATA raid card.

Similar Messages

MOVED: [865PE/G Neo2 Series] Desperation - Help O/C 865PE-NEO2-LS w/2.8Ghz P4 Northwood - Just won't go

This topic has been moved to Overclockers & Modding Corner.
[865PE/G Neo2 Series] Desperation - Help O/C 865PE-NEO2-LS w/2.8Ghz P4 Northwood - Just won't go

This topic has been moved to Overclockers & Modding Corner.
[865PE/G Neo2 Series] Desperation - Help O/C 865PE-NEO2-LS w/2.8Ghz P4 Northwood - Just won't go

MSI 865PE-LS Neo2 Help and Info

Hi
I bought a MSI 865PE-LS Neo2
the motherboard is running Intel 2.8 800mhzFSB cpu
I would like to know what would be the best /fastest memory to run on this motherboard
I need to know why the bios performance setting revert to slow wont run the fast,turbo or ultra turbo settings also no sign of PAT/DOT
I would like to know the current/best bios settings to run the memory/cpu Kingston KVR400X64C25/512
Intel P4 2.8ghz 800FSB
Kingston KVR400X64C25/512 512MB 400Mhz PC3200 DDR Non ECC DIM
Albatron 4800SE
WD 120gb
Audigy2

Hi guys
thanks all for the input
still require best config for this
I have just been email bios VS A6728IMS.161 not sure if I should try it ? ?
exact setup specs please
thanks
tony
IntelP4 2.8ghz 800mhzFSB
WinXP Pro - SR-1 + updates
MSI 865PE LS Neo2 Bios Vs 1.52
2x Kingston KVR400X64C25/512
Albatron Ti 4800SE 128
WD 120gb
Thermaltake Xaser3 (blue)case
420w PSU

Problem installing SATA on 865PE/G Neo2

Guys, dont know if you can help... My system has been stable for some time, and then I installed a 200G SATA drive. After running DVD Rebuilder (with the temp file and reading writing to the drive) for a few hours I get the BSOD IRQL_NOT_LESS_OR_EQUAL. Tried changing memory around with no success. System was stable until I put the drive in.. Any ideas?
System:
400W PSU
MS-6728 865PE/G Neo2
Intel P4 2Ghz
Win XP Pro SP2
DVD-Rom
DVD-RW
IDE 9G HD (OS installed)
Ge-Force Video card
SATA 200G HD (causing problems)

Question for you...
These IRQL_NOT_LESS_OR_EQUAL errors usually displays in the following format: Stop: 0x0000000A (parameter1, parameter2, parameter3, parameter4) IRQL_NOT_LESS_OR_EQUAL*** Address x has base at x - filename
Did you note the offending application filename? If you know what is the filename of the application causing the crash, you can narrow down the possibilities a bit more.
BTW, MS knowledge base link on this particular type of error: http://support.microsoft.com/default.aspx?scid=kb;EN-US;314063
In the knowledge base, Microsoft does not mention insufficient power as a cause. Especially since you already tried another HDD and it works, it is most likely NOT a power issue.

MSI 865PE LS Neo2 and bios A6728IMS.162

I would like some info on
MSI 865PE LS Neo2 Bios Vs A6728IMS.162 I received by email
still require best config for this bios and motherboard
to run memory for 2 x KVR400X64C25/512 memory
I have just been email bios VS A6728IMS.162 not sure if I should try it ? ?
exact setup specs please
thanks
tony
IntelP4 2.8ghz 800mhzFSB
WinXP Pro - SR-1 + updates
MSI 865PE LS Neo2 Bios Vs 1.52
2x Kingston KVR400X64C25/512
Albatron Ti 4800SE 128
WD 120gb
Thermaltake Xaser3 (blue)case
420w PSU

Hi guys
thanks all for the input
still require best config for this
I have just been email bios VS A6728IMS.161 not sure if I should try it ? ?
exact setup specs please
thanks
tony
IntelP4 2.8ghz 800mhzFSB
WinXP Pro - SR-1 + updates
MSI 865PE LS Neo2 Bios Vs 1.52
2x Kingston KVR400X64C25/512
Albatron Ti 4800SE 128
WD 120gb
Thermaltake Xaser3 (blue)case
420w PSU

[865PE/G Neo2 Series] 865 PE Motherboard problem?

I have MSI 865 PE neo 2 MB,intel pentium 4 2,6C HT,and recently I have flashed it's bios with a new one,the new bios said that it can reduce the CPU temperature.I have flashed it carefully,follow the faqs and everything seems alright.The problem is I used corsair cmx-256C2,the reference say that it's can run in CL 2(2-3-3-6) and after I flashed the bios my memory run in 2.5-4-4-8(the default timing from the mother board) and when I change to 2-3-3-6 the system won't startup,it says the timing is too tight .I didn't find this problem with my old bios,and I doesn't want to change back the bios to the old one,because the temperature differences is to high(with old bios CPU idle=47 degrees,new bios = 38 degrees)
Anyone know how to solve the problem?
Thx

So the new bios did'nt change the CPU temperature but just only correct the temperature report?oh my....
I flashed it using Live Update 3,and I am forgot to save my old bios,so where I can find the old bios for my MB.It seems the MSI website didn't provide it.
And why did MSI releasing new bios while stil have defect on it to the customer?it can make unexperience user (including me) dissapointed when knowing it.
Oh by the way,I bought the MB about 2 years ago and I am satisfy with the performance and stability( I am using it about 21 hours a day),and I still planed to use it.
And why my Mb didn't have onboard lan,I saw in the website the other had.I have added it later and cost me $10.

[865PE/G Neo2 Series] 865 PE NEO 2 burn in the place where the on/off motherboard are affect

hello ppl
got this problem that the D led blacket show mi 3 red n one green meaning it is intailzling the keyboard controller but it hang there very long so i decided to remove my keyboard and everything else sound card first, then is cd rom n floppy drive, it still show mi tis problem. when send for service under a 2 year warrttey . they people told mi that that is burn at one area which will cos the on off of the motherboard to be hav problem...... tis they sae need to send to mainbranch at tawain for repair. nw dun know can repair or nt
anyone got ans
pls reply thanks

If you have 2 pieces of RAMs, try with only 1 piece of RAM at a time and see if the problem still occurs.
Try clearing CMOS as well.

[865PE/G Neo2 Series] Suggestions for excellent Air/Fan Cooling - P4 Northwood

Guys, I need some advice here. I've got my 2.8 Northwood up to 3.16 (yea, I know, not great or anything but good enough for right now).
Anyway, with the coming of the blazing Summer temps hitting Michigan in the high 80-90s, my case and CPU temps are skyrocketing. I am finding that my idle temps, once at 31C are now at 35-36C, and the CPU temps once at 42C max under load are now reaching 50+ C. Also, this is the first time in months upon seemingly endless months that I am now getting random reboots, and I am sure it is due to soaring temps and heat problems. The room temps here are killer, and right now are in the high 70s...
I would like to please hear your suggestions/recommendations on a good AIR/FAN cooling solution for my specs I have listed below. I am looking for something that is not very loud if possible, I welcome and thank you for your comments!
865PE-NEO2-LS (601-6728-020)
AMI BIOS version 2.5
P4 Northwood, Socket 478, 2.8 Ghz/800Mhz FSB HT Enabled
4 DIMMS (256MBx4)=1GB KingMax PC3200 DDR400, Model # MPXB62D-38KT3R-PEA
PowMAX PS LP-8800D, 400 watt, max load +3.3@28A,+5@30A,+12@25A,[email protected],[email protected],+5vsb@2A, 70% min@full load
INTEL 865 .INF Drivers (6.0.1.1002 5/7/2004)
Main: Western Digital Raptor, 10K rpm, 36GB
2nd: Maxtor ATA133 7200rpm 120GB
CD-RW: Lite-On 52x32x52
BFG Tech GeForce 6800 GT OC 256MB GDDR3 AGP Graphics Card
SoundBlaster Audigy 2
ViewSonic Professional P225FB 22" monitor
Current Settings:
Configure SDRAM Timing by SPD   Disabled
CAS# Latency   3
RAS# Precharge   4
RAS# to CAS# Delay   4
Precharge Delay   6
Burst Length   8
AGP Aperture Size   128
FREQUENCY/VOLTAGE
Performance Mode (slow, fast, turbo, Ultra Turbo)   SLOW
DRAM Frequency   452
Adjust CPU Bus Clock (Mhz)   226
DDR Clock (Mhz)   452
Adjust AGP/PCI Clock (Mhz)   66.66/33.33
CPU Vcore Adjust   Yes
CPU Vcore   1.5375
DDR Power Voltage (Default is 2.50)   2.6500
AGP Power Voltage   1.5000
SiSoftware Sandra Prof. 2005 System Info
Front Side Bus Speed (4x)/Memory Bus Speed (2x)   226
Front Side Bus Data Rate (FSB Speed x4)   904
Memory Bus Speed (FSB Speed x2)   452
CPU SPEED (GHz with 14x multiplier)   3.16
CrystalCPUID 4.4.5.253 (C) 2002-2005 hiyohiyo
Crystal Dew World [http://crystalmark.info/]
OS : Windows XP Professional SP1 [ 5.1 Build 2600 ]
Date : 2005/06/08 0:48:10
CPU Name : Intel Pentium 4 HT (Northwood)
Vendor String : GenuineIntel
Name String : Intel(R) Pentium(R) 4 CPU 2.80GHz
Architecture : x86
Process Rule : 0.13 um
Platform : Socket 478 [2]
CPU Type : Original OEM processor
Number(Logical) : 2
Hyper-Threading : 2
Family : F
FamilyEx : 00
Model : 2
Stepping : 9
APIC : 00
Brand ID : 09
Microcode ID : 14
Feature : MMX SSE SSE2 HTT
PowerManagement :
Current Original
Clock : 3164.35 MHz 2800.00 MHz
System Clock : 226.03 MHz 200.00 MHz
System Bus : 904.10 MHz 800.00 MHz
Multiplier : 14.00 14.00
Data Rate : QDR
Over Clock : 13.01 %
L1 T-Cache : 12 KuOps
L1 D-Cache : 8 KB
L2 Cache : 512 KB [Full:3164.35 MHz]
Memory : 1024 MB
CPUID : EAX EBX ECX EDX
00000000 : 00000002 756E6547 6C65746E 49656E69
00000001 : 00000F29 01020809 00004400 BFEBFBFF
00000002 : 665B5001 00000000 00000000 007B7040
80000000 : 80000004 00000000 00000000 00000000
80000001 : 00000000 00000000 00000000 00000000
80000002 : 20202020 20202020 20202020 6E492020
80000003 : 286C6574 50202952 69746E65 52286D75
80000004 : 20342029 20555043 30382E32 007A4847
MSR : EAX1 EDX1 EAX2 EDX2
: 00000080 00000000 0E12000E 00000000
QPF : 3164.350000 MHz
Chipset Information
Chipset : Intel 865G/PE/P/848P (Springdale-G/PE/P)
North Bridge : [8086:2570.02] Intel 82865G/PE/P/848P
South Bridge : [8086:24D0.02] Intel 82801EB/ER (ICH5/R)
Video Chip : [10DE:0045.A1] NVIDIA GeForce 6800 GT (NV40)
BIOS Information by WMI (Windows Management Interface)
BIOS Vendor : American Megatrends Inc.
BIOS Caption : Version 1.00
BIOS Version : AMIINT - 10
BIOS Date : 09/29/2004
SM BIOS Caption : V2.5
SM BIOS Version : 2.3
Mother Vendor : MICRO-STAR INC.
Mother Product : MS-6728
Mother Version : 100
System Vendor : MICRO-STAR INC.
System Model : MS-6728
System Information by DMI (Desktop Management Interface)
SM BIOS Version : 2.3
BIOS Vendor : American Megatrends Inc.
BIOS Version : V2.5
BIOS Date : 09/29/2004
BIOS ROM Size : 512 KB
Mother Vendor : MICRO-STAR INC.
Mother Product : MS-6728
Mother Version : 100
CPU Socket : FC-478
CPU Vendor : Intel
CPU Version : Intel(R) Pentium(R) 4 Processor
Current Clock : 3164 MHz
External Clock : 226 MHz
Max Clock : 4000 MHz

Quote from: swambast on 08-June-05, 12:54:14
Guys, I need some advice here. I've got my 2.8 Northwood up to 3.16 (yea, I know, not great or anything but good enough for right now).
Anyway, with the coming of the blazing Summer temps hitting Michigan in the high 80-90s, my case and CPU temps are skyrocketing. I am finding that my idle temps, once at 31C are now at 35-36C, and the CPU temps once at 42C max under load are now reaching 50+ C. Also, this is the first time in months upon seemingly endless months that I am now getting random reboots, and I am sure it is due to soaring temps and heat problems. The room temps here are killer, and right now are in the high 70s...
I only know that I can't suggest a HS and fan because my temperature is higher than my 2.6GHz Northwood's since i decided to install the Thermalright XP90 and the 92mm UFO Thermaltake fan(~82CFM max.). I recently discovered an old picture from Speedfan saying CPU temp: 40C!!! Now right after boot up, I get 40-44C idle and it can climb up to 60C at full load. I know for a fact that air flow is bad inside the case but it's unbelievable to have 40C+ idle. It can't possibly be the air flow so soon after boot. The pressure (and contact) on the CPU was enough to actually see my CPU stuck on the base of the HS after removing the HS!!! A few pins had to be straightened too.
So, from my experience I think you already rock, since we have 30C(86F) already where I live. The feeling of the XP90 crashed under my boot will ease my pain...Oh, yes it will.
P.S. I 'll give the Arctic Silver a try before smashing the XP90 junk...
P4 2,6GHz Northwood
MSI Neo2-PFS 865PE (v3.2 AMIBIOS)
1 GB RAM PC3200 Kingston & TwinMOS
WD 800JB 80GB-7200RPM
CLUB ATI Radeon 9600Pro
Creative Audigy2 ZS

[865PE/G Neo2 Series] Question-boot from Promise IDE on 865PE Neo2 FIS2R

I bought my first MSI board a couple of years ago, an 865PE Neo2-LS. When I retired that, I went for an Abit 875P IC7-G. I just hated the Abit board, used it 3 months and replaced it with a new MSI 865PE Ne02 FIS2R.
I didn't reinstall WIndows XP Pro with the new motherboard. Everything seemed to be OK until I could get around to a clean install of XP. One reason I wanted the FIS2R model was that I wanted to use the faster Promise IDE connection for my boot drive. I had a heck of a time getting the drive to boot, but it finally worked. I was having a few problems that I thought a repair reinstall of XP might solve. So, I tried that yesterday.
Now I cannot get the same drive to boot from the Promise IDE controller. I saw that setting were changed in the BIOS and I can't figure out how to set them so I can boot from the C: drive on the Promise. It will boot fine from the regular primary IDE controller, but I want to use that for two other hard drives I use for storage. The secondary IDE connection is for a CDRW and DVDRW drives.
I've looked at the FAQs and read the manuals. How do I just use the IDE on the Promise? What should my BIOS settings look like? The Promise drivers are installed on the boot drive, the system will post and I'll see a flash of the Windows XP intro screen, then a flash of a blue screen and it kicks it back to booting again. I've never been able to see what that blue screen is telling me. THe drives I want to put on the Promise controller are PATA drives, I don't want SATA or RAID, just using the Promise as a third connection for IDE drives.
Thanks for any help anyone can offer. I have tried every imaginable way of setting the BIOS, but can't seem to hit the right combination. That's what I did on my first try when I got it working, hit a lucky combination and it worked.

Thank you. I had already tried the settings in the post you linked to. I had no luck there. I've reinstalled the Promise drivers, but the boot drive refuses to go past the Windows flash screen before resetting. I think it's quite simple what I'm trying to do. I have six drives. On IDE 1 I want to two storage drives to be connected. On IDE 2 I'm putting the Cd and DVD optical drives. On IDE 3 (Promise) I would like to have my boot (master) drive and a slave drive. Rearranging cables I can get the drive to boot from IDE 1, but no luck with IDE 3. I think it's the Promise drivers, they appear to be installed, but I don't think they are working. I'm going to copy the Promise drivers to a floppy and reinstall XP with the boot drive on IDE 3 and see if I get anywhere with that.
The link referred more to SATA and RAID setup, I just want to use the Promise IDE. I'd sure hate to have to put the awful Abit IC7-G back in my system as I can only get 5 IDE devices in that one instead of the 6 the MSI should run.

[865PE/G Neo2 Series] DDR Memory with 865PE Neo2-PFS Platinum

SYSTEM SPEC: 400w PSU, Pentium 4 3.2ghz 800mhz FSB (HT), Matrox Parhelia 128 8x AGP card, MSI Neo2 PFS Platinum motherboard.
Hi there. Im looking for some serious help with my computer. I have a MSI 865PE Neo2-PFS Platinum mobo and have been using 512mb DDR RAM with it- the ram is PC2700 (333mhz), non-ECC, ubuffered, non-parity, 184 pin. Now, I have just purchased a new DIMM. This one is
1gb PC3200 (400mhz), non-ECC, Unbuffered, non-parity, HIGH DENSITY- DUAL IN LINE, 128 x 64, 184 pin
It doesnt work and my system refuses to boot up. I checked out the specs of the 865PE Neo2-PFS Platinum, and it says in the table that you can only use 400mhz DDR RAM with an 800mhz FSB processor (which I have). It says it supports 400mhz RAM, "DUAL CHANNEL", non-ECC, unbuffered memory, but no mention of "HIGH DENSITY" or "DUAL IN LINE". Is there a difference between "DUAL CHANNEL" and "DUAL IN-LINE". Also, does anyone know what the difference is between 128 x 4 and 128 x 64, they are both 1gb? SOMEONE PLEASE HELP!!! I have seen some RAM from the same dealer which is not "HIGH DENSITY" and has the 128 x 4 configuration, and is still a 1gb module. Is that safe to buy? What RAM do I need (in detail) for my motherboard. Thanks!

Always useful with a complete systemspec.including PSU and biosversion, so please make one.
Can´t see anything wrong with the basic RAM specification - it also matches the MoBo basic specifications:
- Supports four unbuffered DIMM of 2.5V DDR SDRAM.
- Supports up to 4GB memory size without ECC.
- Supports Dual channel DDR266/333/400/433/466/500/533 MHz and up.
Have you tried removing the old RAM and booting only with the new 1GB stick alone ?
Using mixed RAM, sometimes works in "Single mode" (see mobo manual), but is not recommended.
Running Dual-channel ( 2x512 or 1024x2 ) is preferable and gives best performance, but then you need two identical sticks.
You may also need to increase RAM voltage some in bios (example 2.7v) to achieve best stability.
If you have some RAM compability issues with 1GB sticks - 2x512 RAM stick would be safer and give better performance, unless your aiming for more then 2GB in total.
You can also read about the RAM testreport here;
http://www.msi.com.tw/html/products/mainboard/testreport_pdf/6728v2.0/memory.pdf
About "Dual In line Memory Module" - I think it´s the long version for older DIMM description.
Just like "Double Data Rate" is the long version for DDR RAM.
DDR means Double Data Rate RAM (in opposition to the SDRAM or Single Data Rate). DDR RAM bends the transfer rate for clock cycle. It can go quicker because it executes 2 instructions for cycle of clock of the RAM instead of an only instruction like it is the case of the SDR.

[865PE/G Neo2 Series] Can use Intel IAA v5.0.0.0132 on 865PE Neo2-PFISR board?

I am currently using Intel IAA v3.5.3 configured as RAID 0 on my two SATA HDD.
I've decided to re-format my HDD and reinstall Win XP SP2 and I am wondering whether I can use the latest version of the IAA driver (as shown on Intel website for 865 chipsets). The official driver on MSI's site is only version 3.5.6.6282.
Any help is appreciated. Thanks.

Thanks Vango44.
My M/B have updated to version 3.A (latest as per webiste). I will try to use the new Intel IAA driver v5.x.x when I re-installing my system. I am a "sucker" for updating drivers, etc. I just want to know whether there will be any incompatibility ie. have any one try later versions than MSI's official drivers. Will post after my re-installation. Wish me luck.....

[865PE/G Neo2 Series] Zalman CPU cooler doesn't fit, Northbridge Sink remove?

Hi,
I have a problem fitting a Zalman (CNPS7000B-Cu) cpu cooler - the MSI northbridge sink is too high and too close to the cpu.
Can I replace the NB sink with one with a lower profile?
( Incidently, I'm not overclocking, although I do use this machine as an audio machine and it does get quite hot.
- If I can replace - any recommendations?
- If not - any recommendations for a reasonably priced and quiet cooler that will fit (i.e with a narrow profile).

I had the same problem on my 865PE Neo2-PFS Platinum Edition mobo. Zalman's website indicated that the CNPS7000a-AlCu fits on this board, but it doesn't. The diagonally placed northbridge heatsink is in the way. I originally thought I'd bend a few of the Zalman's fins out of the way, but then I decided if I could do something with the northbridge heatsink. I removed the northbridge heatsink and removed the 2 fins that were in the the way of the Zalman. I wanted to repalce the modded northbridge heatsink using some AS5 but the stock thermal goo (some pink stuff) was impossible to get off, even with alcohol or acetone. So I smeared some AS5 on anyway and just mooshed the heatsink back on with the pink junk and AS5.
I noticed that the northbridge gets really hot at stock speeds (200 FSB). I'm planning on overclocking my 2.4C to 3GHz (250 FSB) today, so I hope the northbridge doesn't burn up. Gonna aim a fan at it and hope for the best.
Hope the "bend 2 fins off the northbridge heatsink mod" helps all you guys that want to put Zalman's on your CPU's.
-Coelacanth

[865PE/G Neo2 Series] DRAM Timing is too tightly, Press any key to reset DRAM timing

hello,
i need some help.
I have been using this system for 1 year and 4 months now. A few days ago, when I booted up my computer, the message "DRAM timing is too tightly. Press any key or DEL to reset DRAM timing." appeared before it started detecting hard drive and CD-ROMS. I pressed a key and the computer continued as normal.
This morning, the problem got worse. I started my PC but my screen remained blank. The HDD light and CD-ROM light came on but the power light remained off. I turned off the PC by holding the power switch. When i turned it on again, it was the same situation but the power light started blinking. I turned off the PSU power from my wall socket and waitied about 1 minute. I turned it on again and the power light started blinking again but slower this time. I repeated the on/off steps by using the power button 2-3times. Finally, I tried pressing a few keys on my keyboard and the power light stopped blinking and remained green. I turned the PC on/off again and this time, it succeded in booting up.
And the DRAM messge appeared again.
I was like trying to start a car on a cold day... only after turning the key a few times did the engine start....
I've no idea what is happening here.
My specs are:
Intel P4 3.0C GHZ L2 512KB, FSB 800MHZ, 478 PIN
2x PC400 512MB DDR CL2.5
865PE Neo2-PLS
400W Power supply
Western Digital HDD 120GB SATA
Maxtor 120GB HDD SATA
Maxtor 60GB HDD IDE
DVD Writer
Creative SB Audigy 2 ZS
Leadtek FX5900 LX 128MB
Thanks
Lifehalo

hi,
i smelled a burning smell from my power supply. i am replacing my power supply. i don't know if it was the cause of the dram timing thing.
i'll post here again after i replace my power supply. Thanks!!
Quote from: Thunder on 13-May-05, 21:00:44
When the comp boots up: press the 'delete' key to enter BIOS
Move the marker to 'Advanced Chipset Features' and press enter
Set 'Configure SDRAM Timing by SPD' setting to [Enabled] and press enter press enter
Press F10, and you woulg get the question 'Save changes and EXIT?', Answer 'YES* and press enter.
If this would'nt help, post back here.

[865PE/G Neo2 Series] Video stop working if I install Intel Inf update chipset software

Hi,
i have big problem with my MS-6728 (865PE Neo2-S) and Geforce 4 Ti 4200.
After installing Intel inf update for chipset my Windows XP Pro SP1 stop booting and freeze (if i use Detonator 61 or higher) or just use standart VGA driver (if i use Detonator version 41).
If i remove Intel chipset (i tried all versions) - video is working good
Why Intel Inf update chipet drivers have conflict with my video card ?

Hi,
i did as You say - remove Windows XP, format my HDD, installed again Windows XP, installed Intel Inf update - system Ok
install video drivers - freeze and crush.
Nothing help ....
I found on this forum that some people have problem with video like me. they talk about bad agp port driver.....
What can i do now ?

[865PE/G Neo2 Series] HELP Please? 865PE Neo2 3.0 HT Engineering Sample

I just recently purchased a Neo2 865pe motherboard. I have a Engineering sample 3.0ht 800mhz proc. I used my ES proc from my asus runnin 3.2ghz@800mhz. I install the proc into the MSI and it came up with 1.6ghz. So I tried to up the cpu multiplier it starts from rang e15x and goes to 21x, but even if I set it to 21x I only still get best 2.25mhz. Can someone please point me to a solution. Thank you.

Engineering Samples are like Test beds CPU, which means that it may not work with all boards.
Like what Wonk has mentioned,increased your FSB from 100MHz to 200MHz with Multiplier of x16 and DDR RAM to be clocked at only 400MHz to obtain the 3.2GHz clock of your CPU.

[865PE/G Neo2 Series] RAID 1 on 865 NEO2-LS

Similar Messages

Maybe you are looking for