865PE Neo 2 - P.. System Crashes While Gaming...not other times.

Hi,
When I played games like WarCraft 3, sometimes after 40 minutes, the whole com freezes, I can still see the game in the screen but everything stops moving, and the screeching sound pops out again.. then I had to reset the com.
What could be the possible problem leading to this?
I have all latest BIOS, Drivers for my devices. Could it be the settings on the Mobo ?
Pls help..
Thanks..
Sam

Quote from: sum on 05-March-05, 00:05:46
Hi, My comptuer have been crashing alot recently too, after reading a few posts, many recommand to adjust the ram voltage to 2.7 would solve the problem, and the question is.. my memory only supports up to v2.6, i am using a pair of 512 Kingston HyperX PC 3200 will it damage the ram if i set the voltage more then it can handle? heres the spec of my rams, any help would be greatly appreciated.. peace
Manufacturer: Kingston
Model: KHX3200AK2/1G
Speed: DDR400(PC3200)
Type: 184 Pin DDR SDRAM
Error Checking: Non-ECC
Registered/Unbuffered: Unbuffered
Cas Latency: 2-3-2-6-1T
Support Voltage: 2.6V
Bandwidth: 3.2GB/s
Organization: two 64M x 64 -Bit
I have the same RAM as you and i have ran it at 2.7v with no problems.

Similar Messages

MSI 280X Gaming 3G - Crashing while gaming

Card is crashing while gaming has been going on since December intermittanly, it was purchased May 2014
Tested with Furmark and seems ok Hit max temp of 60-70 depending on ambient, same temps while gaming but randomly reboots.
Have tried differnt AMD drivers the latest Omega seems more unstable than the lastest beta, but crashing more with this one now.
Rolled back to 14.4 but the same.
Is this a faulty card or do I need a Bios update? ( if so please supply lgacy and uefi bios)
OS : Windows 7 Ultimate 64-bit SP1
CPU: AMD FX-8350   20 °C
RAM: 16.0GB Dual-Channel DDR3 @ 937MHz (10-11-10-30)
MB : Gigabyte 990FXA-UD3 (CPU 1)   25 °C
GFX: S23B550 (1920x1080@60Hz)
    MSI 280X GAMING 3G - 3072MB ATI AMD Radeon R9 200 Series (MSI)   29 °C
    vga bios : ms-v277 tv277ms.350 from MSI Update
    S/N : 602-v277-31sb1402067937
Storage
   1863GB Seagate ST2000DM 001-1CH164 SATA Disk Device (SATA)   34 °C
   1863GB Seagate ST2000DM 001-1CH164 SATA Disk Device (SATA)   31 °C
   1863GB Seagate ST2000DM 001-1CH164 SATA Disk Device (SATA)   28 °C
Optical Drives
   TSSTcorp CDDVDW SH-224DB ATA Device
Audio
   Realtek High Definition Audio
   PSU Corsair CX750
AMD Catalyst :
AMD 14.4
Tried 14.3
& Omega driver

Here you go though I doubt that vbios is the problem:
TV277MS.351 is legacy
TV277MH.351 is uefi
If no help follow >>Posting Guide<<

System crash when gaming (Update: Temperature Problem?)

Hello there
I have a problem: when starting games (Minecraft, Relics of Annorath, Portal, World of Goo tested) my Laptop crashes. The screen gets black and the only possibility to turn it back on is to remove the battery, wait 10 seconds and then reboot. I don't see any error messages, not in the journal and not in the Xorg.0.log. I have a HP 8470w with a Intel i7-3610QM Quad Core and a AMD FirePro M2000 grapics card. I am running kernel 3.10.10-ARCH with fglrx. Is anyone aware of this problem or can help me even just pointing out where to look for the problem? If you need more info, please tell me.
strix:~ $ fglrxinfo
display: :0.0 screen: 0
OpenGL vendor string: Advanced Micro Devices, Inc.
OpenGL renderer string: AMD Radeon HD 7500M/7600M Series
OpenGL version string: 4.3.12441 Compatibility Profile Context FireGL 12.104
strix:~ $ X -version
X.Org X Server 1.14.2
Release Date: 2013-06-25
X Protocol Version 11, Revision 0
Build Operating System: Linux 3.9.7-1-ARCH x86_64
Current Operating System: Linux tirion 3.10.10-1-ARCH #1 SMP PREEMPT Fri Aug 30 11:30:06 CEST 2013 x86_64
Kernel command line: cryptdevice=/dev/sda2:root root=/dev/mapper/root resume=/dev/mapper/swapDevice rw initrd=../initramfs-linux.img BOOT_IMAGE=../vmlinuz-linux
Build Date: 01 July 2013 10:48:42AM
Current version of pixman: 0.30.2
Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
journalctl at the time of my last crash:
Sep 04 12:35:44 tirion logger[13211]: ACPI action undefined: PNP0C0A:00
Sep 04 12:36:01 tirion crond[13217]: pam_unix(crond:session): session opened for user strix by (uid=0)
Sep 04 12:36:01 tirion CROND[13218]: (strix) CMD (~/data/bin/battery)
Sep 04 12:36:01 tirion CROND[13217]: pam_unix(crond:session): session closed for user strix
Sep 04 12:36:49 tirion laptop-mode[13335]: Laptop mode
Sep 04 12:36:49 tirion laptop-mode[13338]: enabled, not active [unchanged]
Sep 04 12:36:49 tirion laptop-mode[13344]: Laptop mode
Sep 04 12:36:49 tirion laptop-mode[13345]: enabled, not active [unchanged]
Sep 04 12:36:49 tirion logger[13347]: ACPI action undefined: PNP0C0A:00
Sep 04 12:37:01 tirion crond[13352]: pam_unix(crond:session): session opened for user strix by (uid=0)
Sep 04 12:37:01 tirion CROND[13353]: (strix) CMD (~/data/bin/battery)
Sep 04 12:37:01 tirion CROND[13352]: pam_unix(crond:session): session closed for user strix
Sep 04 12:38:01 tirion crond[13373]: pam_unix(crond:session): session opened for user strix by (uid=0)
Sep 04 12:38:01 tirion CROND[13374]: (strix) CMD (~/data/bin/battery)
Sep 04 12:38:01 tirion CROND[13373]: pam_unix(crond:session): session closed for user strix
Sep 04 12:38:16 tirion laptop-mode[13426]: Laptop mode
Sep 04 12:38:16 tirion laptop-mode[13430]: enabled, not active [unchanged]
Sep 04 12:38:16 tirion laptop-mode[13438]: Laptop mode
Sep 04 12:38:16 tirion laptop-mode[13439]: enabled, not active [unchanged]
Sep 04 12:38:16 tirion logger[13441]: ACPI action undefined: PNP0C0A:00
Sep 04 12:39:01 tirion crond[13454]: pam_unix(crond:session): session opened for user strix by (uid=0)
Sep 04 12:39:01 tirion CROND[13455]: (strix) CMD (~/data/bin/battery)
Sep 04 12:39:01 tirion CROND[13454]: pam_unix(crond:session): session closed for user strix
Sep 04 12:39:22 tirion laptop-mode[13512]: Laptop mode
Sep 04 12:39:22 tirion laptop-mode[13514]: enabled, not active [unchanged]
Sep 04 12:39:22 tirion laptop-mode[13520]: Laptop mode
Sep 04 12:39:22 tirion laptop-mode[13521]: enabled, not active [unchanged]
Sep 04 12:39:22 tirion logger[13523]: ACPI action undefined: PNP0C0A:00
Sep 04 12:39:44 tirion kernel: usb 3-1.2: new low-speed USB device number 4 using ehci-pci
Sep 04 12:39:44 tirion kernel: hidraw: raw HID events driver (C) Jiri Kosina
Sep 04 12:39:44 tirion kernel: usbcore: registered new interface driver usbhid
Sep 04 12:39:44 tirion kernel: usbhid: USB HID core driver
Sep 04 12:39:44 tirion kernel: input: 2.4G Wireless Mouse as /devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.2/3-1.
Sep 04 12:39:44 tirion kernel: hid-generic 0003:04F3:02F4.0001: input,hiddev0,hidraw0: USB HID v1.11 Mouse [2.4G
Sep 04 12:39:44 tirion laptop-mode[13583]: Laptop mode
Sep 04 12:39:44 tirion laptop-mode[13585]: enabled, not active
Sep 04 12:39:44 tirion laptop-mode[13612]: Laptop mode
Sep 04 12:39:44 tirion laptop-mode[13613]: enabled, not active
-- Reboot -- <-- This Reboot here was not planned! :)
Sep 04 12:43:35 tirion systemd-journal[247]: Allowing runtime journal files to grow to 597.7M.
Sep 04 12:43:35 tirion kernel: Initializing cgroup subsys cpuset
Sep 04 12:43:35 tirion kernel: Initializing cgroup subsys cpu
Sep 04 12:43:35 tirion kernel: Initializing cgroup subsys cpuacct
Sep 04 12:43:35 tirion kernel: Linux version 3.10.10-1-ARCH (tobias@T-POWA-LX) (gcc version 4.8.1 20130725 (prere
Sep 04 12:43:35 tirion kernel: Command line: cryptdevice=/dev/sda2:root root=/dev/mapper/root resume=/dev/mapper/swapDevice rw
Edit:
After not finding anything in my graphic settings I just ran lm_sensors with the following output:
strix:~ $ sensors
coretemp-isa-0000
Adapter: ISA adapter
Physical id 0: +57.0°C (high = +87.0°C, crit = +105.0°C)
Core 0: +55.0°C (high = +87.0°C, crit = +105.0°C)
Core 1: +53.0°C (high = +87.0°C, crit = +105.0°C)
Core 2: +54.0°C (high = +87.0°C, crit = +105.0°C)
Core 3: +57.0°C (high = +87.0°C, crit = +105.0°C)
acpitz-virtual-0
Adapter: Virtual device
temp1: +55.0°C (crit = +128.0°C)
temp2: +53.0°C (crit = +128.0°C)
temp3: +43.0°C (crit = +128.0°C)
temp4: +45.0°C (crit = +128.0°C)
temp5: +20.0°C (crit = +128.0°C)
temp6: +127.0°C (crit = +128.0°C)
temp7: +0.0°C (crit = +128.0°C)
temp8: +0.0°C (crit = +128.0°C)
Could these 127°C be the problem? It's getting pretty hot while gaming but 127°C is almost impossible...
Last edited by strix (2013-09-05 09:49:24)

temp6, temp7, temp8 are strange.... but because it's impossible reach these temps (+127 and +0) I think those sensors are not used or bad report data
if you think it's a overheating problem, you must log temps (sensord+rrdtool)
so you'll get the latest temps before the PC crashes

[Solved] New GT70 20D constantly crashing while gaming

Hi everyone,
I bought this new laptop last week, but I've been having trouble playing games with it. I mostly play final fanasy XIV (online), but it keeps crashing while playing. It either just crashes altogether, giving weird noises and me having to restart it, or the framerate ingame suddenly drops to like 8-10 fps, and I can't get it to go up anymore.
Sometimes it also locks up other programs (such as just now, when I alt tabbed out of the game my mouse would only stay in the upper left corner, also forcing me to restart). This happens within half an hour to an hour of gaming and is driving me mad.
I have tried updating all of the drivers to the most recent versions (on the official
websites, not the msi website), getting rid of the killer network program, and installing the drivers only. No result so far. If I cannot solve it, I will send the laptop back and probably get another one, but before that, any suggestions on how I could solve this?
Does someone know how I can view a log system of the crashes so I can see where it is coming from maybe?

Do you have crashing photos?
Tell your current system information(BIOS/EC/VGA driver version). You can check your BIOS and EC version in BIOS menu, System Information.
For the mouse, are you using touch pad? or external mouse?
You can find BSOD dump files at c:\windows\minidump and check it by using BlueScreenView.

System crashes while exporting

hi all,
I'm all new to captivate and I'm working at my first project
with it.
I'm doing a navigation site demo, which will be distibuted on
cd.
I'm working on just one .cp file because I need the project
to run as standalone, not inside internet explorer; the .cp file is
48 MB.
I got several issues on registering the last two slides
(they're about 80), and now it's impossible exporting all the demo,
because the system crashes when captivate is exporting slides.
I'm wondering if I made something wrong in organizing my
project.
Correct me if I'm wrong, but I understood that if you want to
divide your project in more .cp files, you must publish as html,
not standalone. That's the reason why I didn't subdivide my project
in more .cp files.
Am I wrong?
Can anyone suggest something to solve the problem, preserving
the standalone solution?
Thanks in advance, and excuse me If I made some newbie
questions :-)
Alessia

To All who are experiencing crashes during publishing,
check
this link for a Tech Note
. As a rule of thumb, keep your Captivate project files to less
then 10 MB whenever possible, and the SWFs, of course,
correspondingly small.
About that "you can't create multiple standalones" - that is
just bad advice. Of course you can. BUT keep in mind that there
will always be a noticeable "lag" when daisy-chaining executables,
while the Flash Player closes on one file, and reopens to play the
next in the "daisy-chain".

Mac OSX 10.6.8 - The whole system crashes while navigating in Soundcloud

While navigating in soudcloud the whole system crashes and I have to force restart in my laptop (Macbook pro 2010)
Back to Safari?

We're sorry to hear that Firefox is crashing when you open it. Please do the following to give us crash IDs that will help us understand more about the crash.
#'''(OS X 10.6 or previous)''' Click the '''Finder''' icon in the dock. Your home folder will be selected. In the right side of the window, click the Library folder to open it. Then open the "Application Support" folder, the "Firefox" folder, the "Crash Reports" folder and finally the "submitted" folder.<br>'''(OS X 10.7 or above)''' Click the '''Finder''' icon in the dock. On the menu bar, click the '''Go''' menu, hold down the '''option''' or '''alt''' key and select '''Library'''. A window will open containing your Library folder. Then open the "Application Support" folder, the "Firefox" folder, the "Crash Reports" folder and finally the "submitted" folder.
#Open the 5 most recent files with a text editor and copy the IDs.
#Paste each ID with '''bp-''' into the reply window on the forums.
Thanks in advance!
You can find more information and troubleshooting steps in the [[Firefox crashes]] article.

System crashes while capturing in CS5

Recently installed Samsung Kies software for supporting my Galaxy cell phone. Same day Win7 started crashing while capturing video in Premiere Pro CS5. It crashes after random number of minutes capturing. There's no problem with any other aplication, Adobe or not, and Premiere Elements7 captures video with no problem at all. Uninstalled Kies but Win7 keeps crashing. Any experience with this combination of softwares?

I have one computer for everything http://forums.adobe.com/thread/652694?tstart=0 and have not had any problems
But, I do not have and have never heard of "Kies" software
Generally speaking... if something works and then stops working when new software is installed... that is clear to ME that the new install is the problem
I always make a full boot drive image before installing anything
You should buy software to make a full backup of your hard drive to an external USB hard drive... which makes restoring very easy
The product I use is at http://www.terabyteunlimited.com/image-for-linux.htm
Image runs off of a bootable CD via Linux (the Zip you download includes a program to make the bootable CD) and it reads EVERYTHING on the drive, even the hidden registration information, so everything is restored when needed... and you may restore the image to a brand new drive and not have to re-install anything
Please note that I own no part of Image, and I don't get a referral fee (that is just a plain web link) but I use the program and it has saved me a LOT of trouble when I had a hard drive die... and I was able to restore everything and not have to re-install or re-activate a single program, from Windows on up

Entire System Crashing while transferring songs to iPod

I run a 17" 1.5 GHz powerbook with 10.4.3. I recently bought a 60 gb 5th gen iPod. About 3 weeks ago I was adding a CD to my iPod. The entire system crashed, I wasn't sure of the problem. So, once i forcefully rebooted(all black screen, ..hold down the power button in 15 different languages..), I opened up itunes, checked to see if the songs actuallu transferred, they had not, so i went to transfer them again, after 5 songs...BOOM..another crash box.
Today, I was transferring a cd of 320kbps audio flies(Mozart) to it and it happened again. Can the iPod not handle multiple song transfers of high bit rate songs? Not sure why this is happening, has anyone else experienced this?
Powerbook G4 Mac OS X (10.4.3)

I am in the same boat as you guys.
I have a 60 gig Black 5G iPod. Loaded primarily with video.
It is syncing to a 10.4.3 iMac G5.
I have been using the iPod trouble free for 2 weeks now. Syncing everyday, removing and adding video. No problems.
Last night I attempted to add a number of videos that would have filled up the device. Once I was syncing the last, or second to last, video and the counter in iTunes showed there was about a gig of space left available on the iPod I would get a Kernel Panic (grey screen, power button, 5 languages, telling me to restart).
This happened twice before I removed a handful of videos to keep the iPod from filling up. This seemed to relieve the problem and the iPod synced like normal.
Otherwise the iPod has been performing as expected, video playback is great, syncing otherwise is fine.
My panic.log is very similar to yours rdstuart
Wed Jan 4 00:18:10 2006
panic(cpu 0 caller 0x00247294): BlockAllocateContig: allocation overflow on "Da vPod"
Latest stack backtrace for cpu 0:
Backtrace:
0x00095698 0x00095BB0 0x0002683C 0x00247294 0x00246D8C 0x00245CC0 0x0022875C 0x000FBD60
0x000F5338 0x0027D238 0x0027D060 0x002A9BF4 0x000ABE30 0x00000000
Proceeding back via exception chain:
Exception state (sv=0x3A854280)
PC=0x90053AEC; MSR=0x0000D030; DAR=0xE00FF000; DSISR=0x42000000; LR=0x90B51504; R1=0xF0305B20; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.3.0: Mon Oct 3 20:04:04 PDT 2005; root:xnu-792.6.22.obj~2/RELEASE_PPC
So, a follow up question, anyone reading this thread completely (and I mean completely, save for a few megs) maxed out their 5th gen iPod? 30 or 60 gig qualifies as it seems to occur on both models.
Basically I am trying to determine the root of the problem. Is this a serious hardware problem which would warrant an exchange?
Or possible a problem/flaw in the database structure of the iPod that could be rectified via a firmware update?
Has anyone talked with Apple Tech Support about this issue?
My iPod is absolutely great otherwise, none of the many complaints others in the forum have had, and so if this is just a case of leaving a gig or so free on the iPod until a fix materializes so be it! I would rather avoid an unnecessary exchange if possible.
I just want to avoid major hardware issues downs the line naturally.
Thanks for your help and advice in advance.

MSI P67A GD65 System Freezes while Gaming

hey
i m facing system hangs/freezes while gaming. it is all along working fine but suddenly problem arrises outta nowhere. mostly happens in Metro Last Light Game. i did change multiple things like 2 different rams stick, Bios are 4.1v (at default), i tried 2 different GPUs like 290 and 580 but stilll facing same issue. dont know why.
if you can help on it this, it would be alot appreciated.
m PC
MSI p67a GD65
I5 2500K
8GB RAM
800w PSU

What is the actual power supply?
Follow this >>Posting Guide<<
Make sure you run latest BIOS.
PS: Intel ME driver is crucial, without it system won't work properly, and that's why it didn't freeze anymore. Same applies to GPUs: if you have 400W power supply and want to run 2-way SLI, it will be fine until you install drivers, which make the computer and graphic cards recognise how much power they have and so on

Crashing while gaming

Hi all,
I am new to building my own PC (or at least specing them).
Here is what I just picked up:
MSI K8N Neo4 S 939
AMD Athalon 64 3200+ (939 socket)
1024MB PC 3200 RAM
VGA GIGABYTE Nvidia GeForce 6600 256MB PCI-Ex
I play Everquest. What is happening is that my computer will totally freeze up while playing. What I mean by this is I will be playing the game and the screen will just lock up - leaving the image just as it was when it froze. At the same time I hear a kind of "digital burp" in my speakers. A buddy said that sound is normal when I game does this.
It happens totally randomly - sometimes when the game is loading... sometimes when I am just kind of hanging around not doing much... then other times I can play for hours with no problems. The other day, I was just standing around in one of the zones and I kept freezing over and over.
When this happens I have to hard reboot at each freeze.
I don't know a lot about systems in general, so any advice you could give would be a great help. The guys who sold me the computer said that they have a few other people with this same problem when playing EQ or World of Warcraft. They are still searching for an answer as well.
Thanks,
Charles

Charles,
First, we need information, and most of this should have been your signature.
When ever possible in the part numbers of you components, and most of use around here have learn the hardware the total watt of you power supply means nothing. So, include the load rating of each of you powers output voltages.
By the way, one of the main reasons, but not the only reason is to small a power supply.
Look at my signature and others to see the type of information we need to help and I am sure you get more help than you need.
Roger

GTX580 Twin Frozr II OC: Crashing while gaming

I have a GTX 580 Twin Frozr II OC. My computer crash randomly while gaming. The screen turns black and the computer restarts. It happens on different games. I have the latest bios on my motherboard and video card (70.10.17.00.01). I have also tried many different drivers. Currently I have the latest installed (320.49).
I have tried decreasing the core clock from 800 to 772 and increasing the Core voltage from 1025, 1038 and 1050, as well as different combinations of those.
Config:
Core i5 2500K @ 4.4Ghz
Kingston HyperX Genesis 8GB @ 1600Mhz, 2 DIMMS (1.65V, 9/9/9/27)
ASRock Fatal1ty P67 Professional
Corsair HX 850W
GTX580 Twin Frozr II OC
2TB WD Black Caviar
Windows 7 Ultimate x64
Single Monitor
The S/N is 602-V255-01SB1102013982.
This is my bios http:// www .mediafire.com/?o6p4wf0prxa6tv5
Thanks!

The card came overclocked from factory. I decreased the clocks to the Nvidia default. The core clock to 772, Shader clock to 1544 and Memory clock to 2004. I also increased the core voltage to 1038.
The idle temperature is 38 C and at full load it goes to 82 C maximum.
Still, with all this, it still crashes now and then, but much less frequently.

Trying to combine folders within LR4 from two separate drives without creating duplicates--sometimes it won't let me transfer to destination folder because it says files are there when they are not; other times, allows duplicates to transfer

Trying to consolidate 261K+ of images within LR4 between two drives. Someone who was "helping" me with my Library in LR4 for some reason took some but not all of the file folders from my main backup drive (M) and duplicated them onto a partitioned hard drive (E) directly on the computer. The duplication is huge, so I am trying to condense them all back onto the original backup drive M, particularly since I believe there are also folders on the partitioned backup drive E that do not appear on the main one M, and there are many more file folders on M that are not on E, so that is the destination drive.
CONSOLIDATION: When I try to drag either the file folders or the individual files from the duplicate drive E to the original drive M to combine the two drives since the folders in many cases for some reason are not identical, sometimes LR4 says the files already exist when they clearly don't. Other times it allows me to drag and drop all files, even if the exact duplicates are already on the destination drive, thereby doubling the number of files per image and creating more duplicates. Right now I am opening each file folder on the duplicate drive E, looking at what extensions and file names are there, scrolling to the original drive, making sure they appear to be identical, then going back to the duplicate drive E, deleting the images in the folder, removing the folder, and moving to the next folder on the duplicate drive E. *There has got to be a simpler way.*
CONSOLIDATION APPROACH: I did start to create file folders names A, B, C and group file folders under them to reduce clutter, since those header folders can be closed down when not in use, but now I am wondering if I should have done that alphabetization to the main backup drive rather than to the partitioned backup drive.
My goal is to consolidate the two drives down to one, delete as many images along the way that I know I will never miss, then backup the catalog and export it to an external drive and then copy that to yet another drive for offside storage. Does this sound like the proper plan? Last time it took almost 24 hours and over a terabyte to export the catalog.
DUPLICATION: I also have many file folders that have the exact same image in them. One portfolio image may actually be in eight different folders, with the exact file, file name, file size, and date, even though I always have checked "no duplicates on import," How can this be? What is the best way to sort through duplicates? Why are the files in some of the duplicate folders not in numerical order? If I do a search and call up a file # and find 15 duplicates, the only way I can find where those duplicates reside is to take each duplicate, right click to Locate Folder in Library, then once I find it, I have to go back to All Photographs>Text.search for file #, go to the second duplicate, right click to Locate Folder in Library, then once I find it, I have to do it all again. Is there a simpler way to see all the occurrences in their respective folder locations at once?
SEARCH BY FILE FOLDER NAME ONLY: I also find I can't search for a file using a folder name (for example, "John_Doe"). I can only search by file #, keywords, or camera/lens/date, etc. Why will it not work to use All Photographs>Text>search for Doe? In other words, if I didn't keyword the individual files as John Doe, I can't search for them by that moniker.
BACKUP: It also appears that the only way I can back up the catalog is to shut down LR. Really?!
FOLDER LIST PRINTOUT: Is there a way to print out the Folder list (other than a screen shot)? I have so many file folders on each drive since I sort not by Year/Month/Date but by subject. It makes trying to compare duplicate folders quite unwieldy.
SLOW RESPONSE: And finally, as though that weren't enough, why does LR4 continually blink to a white screen after each keystroke? Takes forever just to be able to click through images, view info after hovering, etc. All other programs are closed down and the operating system shows very little memory being used.

A brief and probably non-helpful answer: I know of no way to eliminate your large amount of duplicates other than by repetitive, tedious manual effort.
*There has got to be a simpler way.*
I hope you're right, but I don't think there is a simpler way.
BACKUP: It also appears that the only way I can back up the catalog is to shut down LR. Really?!
Yes, really

MSI gt683 - constant crashes while gaming

Hello
I decided to look for solution in forum, cause this problem is drivin me nutz.
I have really frequent crashes in almost every game i play (even on the lowest possible details) Games like heartstone, heroes of newerth, which i find not really advanced in case of graphic, cause frequent crashes. It happens in mass effect 2, fallout 3, , and practiclly every other. Games like guild wars usually freeze in loging screen already. There are few particular types of the problem
1. Screen goes black for a half a second and then goes back to the game ( i can see my desktop for a while) - i guess it has to do something with graphic card (nvidia gtx 560m)
2. Screen goes black for a half a second and goes back to the game (can see desktop as well), but it changes resolution for the game to other (higher)
3. The gaming screen goes blue/browny/black and i have to restard computer
4. The games Freezes totally, cant open the menager, however programs in a background (like skype) are still working
5. Games slows down 1000000% (mouse bearly moving) and eventually completly stops (no programs in a background working). I can hear this buzzing sound
This problem happens all the time ( even if computer was sleeping whole night, in the morining it starts to freez after i try to play anything). Problems never occur when i watch videos, listen to music etc.
Recently i got a issue with a conector( i believe its called, the part where the power supply is attached). Guy fixed it, and cleand from dust + exchanged the thermal grease. The problem is still occuring.
About 2 weeks ago I've made a windows recovery, in the beginning was slightly better (could play few more games with few less crashes), but in the end its almost not playable again. I have no idea where should i look for the solution to this problem. I hope You guys will have any idea Thanks a lot in advance!
PS: Is it possible that it might be a sound problem? I just realised, the game (heartstone) didnt crash when i had my sound disabled in it

Do you have crashing photos?
Tell your current system information(BIOS/EC/VGA driver version). You can check your BIOS and EC version in BIOS menu, System Information.
For the mouse, are you using touch pad? or external mouse?
You can find BSOD dump files at c:\windows\minidump and check it by using BlueScreenView.

Unexplained System Crashes While Running InDesign

I am running InDesign CS6 8.0.2 on a MacBook Pro with OS X 10.9. InDesign launches just fine, and I'm not getting any error messages. But once in a while my system just stops responding. I can't even force quit applications. I have to just manually power down by holding the power button. I thought it might be a hard drive issue, but I recently replaced my stock HD with a SSD, and the problem persists. And by the way, there is no application crash or error report available. The system just freezes completely and I have no option but to power down.
The only common thread I can point to is that InDesign is running.
Does anyone have suggestions about how to understand what is happening? If InDesign is causing the system to freeze, could it be a plugin or extension issue?
I'm grateful for any support or ideas you might offer.

Hi Eugene, Thanks for offering to help. Here is some of the information you requested:
Hardware Overview:
Model Name:          MacBook Pro
Model Identifier:          MacBookPro9,1
Processor Name:          Intel Core i7
Processor Speed:          2.6 GHz
Number of Processors:          1
Total Number of Cores:          4
L2 Cache (per Core):          256 KB
L3 Cache:          6 MB
Memory:          16 GB
Boot ROM Version:          MBP91.00D3.B08
SMC Version (system):          2.1f175
Serial Number (system):          C02J604LF1G4
Hardware UUID:          76824BFD-88A3-5D43-B6E0-15EA0F708A85
Sudden Motion Sensor:
State:          Enabled
System Software Overview:
System Version:          OS X 10.9 (13A603)
Kernel Version:          Darwin 13.0.0
Boot Volume:          Macintosh HD
Boot Mode:          Normal
Computer Name:          Andy’s MacBook Pro
User Name:          Andy Johnston (AJ)
Secure Virtual Memory:          Enabled
Time since boot:          1:18
I don't know that I can do anything to reproduce the freeze. What happens usually is that I open InDesign and work on a file. When finished, I save my work, and move to another task in a different application (managing email in the Chrome browser, for example). At some point in the future and with no apparent action to initiate the crash, my system stops responding.
The crash has probably happened while I was using InDesign in the past, but most of the time I notice the system begin to lock up when I'm in the browser. I know, I know...maybe the browser is the culprit.
I did look at the Extension Manager and noticed there were quite a few warning icons. When I hover over them, I see the message "Extension may not function properly because it does not meet the dependency condition."
Does this information help track down the issue?

System crashes but crashreporter not working

My Mac Pro is crashing every time it goes to sleep - but I don't know why, and I can't find out why because crashreporter seems to be disabled. The message below was the last message before one of these crashes.
Mind you, this is a very unstable Mac since the upgrade to Yosemite. All sorts of things fall over all the time and I am constantly rebooting.
It just doesn't work at the moment!

Please read this whole message before doing anything.
This procedure is a test, not a solution. Don’t be disappointed when you find that nothing has changed after you complete it.
Step 1
The purpose of this step is to determine whether the problem is localized to your user account.
Enable guest logins* and log in as Guest. Don't use the Safari-only “Guest User” login created by “Find My Mac.”
While logged in as Guest, you won’t have access to any of your documents or settings. Applications will behave as if you were running them for the first time. Don’t be alarmed by this behavior; it’s normal. If you need any passwords or other personal data in order to complete the test, memorize, print, or write them down before you begin.
Test while logged in as Guest. Same problem?
After testing, log out of the guest account and, in your own account, disable it if you wish. Any files you created in the guest account will be deleted automatically when you log out of it.
*Note: If you’ve activated “Find My Mac” or FileVault, then you can’t enable the Guest account. The “Guest User” login created by “Find My Mac” is not the same. Create a new account in which to test, and delete it, including its home folder, after testing.
Step 2
The purpose of this step is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Please take this step regardless of the results of Step 1.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of Steps 1 and 2.

865PE Neo 2 - P.. System Crashes While Gaming...not other times.

Similar Messages

Maybe you are looking for