865PE Neo 2P won't go into SETUP.. DHCP??

Hi, I'm new to MSI. I have a new 865PE Neo2 P board.. unfortunately, I can't get it to go into setup bios no matter what I try. It gets into some Intel boot.. where it beeps .. print out "Intel ... Realtek gigabit ethernet.. Media problem: check cable".. and then if I plug an ethernet cable in .. it goes into "DHCP .... blah blah.. PXE mon exiting".. and then the whole thing loops again.
How can I get this thing to go into BIOS / Setup? I've tried everything the book suggests.. DEL, ctrl-alt-delete, F11-F10 etc.. almost to the point I am beginning to wonder if it's even looking at keyboard input..
HELP!!!!
(please respond to [email protected] if you can, and thanks in advance for your help).

Ahh... It must be trying to boot from LAN...
I suggest that you try clearing CMOS, taking the mobo battery out for few seconds and place it back and boot up again and see if the problem persists.

Similar Messages

865PE neo 3-won't see sata drive after cmos reset

cpu-z reports i have a ms-6728; the mobo has 865PE neo three. i was having some problems with memory and used the jumpers to reset the cmos.
now the bios will not see my sata drive. took the drive out and to a shop and it is seen fine at the shop. running of my ide ata drive.
looked at manual and in my bios i don't have the option under "on chip IDE configuration" in my bios.
my cmos = A6728IMS v.50 092204
thanks for any help

If you are still having problem. Please use the following configuration.
ATA On Chip Mode: Native
ATA Config: SATA
PATA Keep Enabled: Yes
PATA Channel Selection: Both
Set SATA as RAID: No
If it do not pick up, change mode from Native to Legacy.

Ipad 2 won't go into setup

I have a new Ipad2. I plugged it into my laptop where other ipods are synced. Laptop went dead when Ipad touched laptop. My Gurue? said" bad usb ports and or not enough power. I switched to desktop signed in and nothing happens.

this is a software glitch, i suggest holding the home button and power button together untill you see the apple then let go, do not slide to power off, if all else fails you might have to restore the device to factory settings, still doesnt do that then its a hardware issue, and its probably going to be 250$ or more to replace

I fitted new battery but it won't charge. when plugged into wall socket gets to itunes setup but no further. when connected to computer not enough battery to turn on to get into setup. Any ideas please?

i fitted new battery but it won't charge. when plugged into wall socket gets to itunes setup but no further. when connected to computer not enough battery to turn on to get into setup. Any ideas please?

turnbui wrote:
i fitted new battery but it won't charge. when plugged into wall socket gets to itunes setup but no further. when connected to computer not enough battery to turn on to get into setup. Any ideas please?
It sounds very very much like the battery. You will need to have it replaced. If you put the failing one in yourself you will need to pay as your Warranty is now void.
Pete

865PE Neo-PFISR Stable in Prime 95----but won't run the 3DMarks at all????

I don't get it.....
This board (865PE Neo-PFISR) is VERY stable in Prime 95-----yet I can maybe get through the first test of any of the 3Dmarks----and PCMark will always fail as well.
I even reverted to STOCK, default settings.
Uninstalled and reinstalled the 9700Pro drivers (Cat 4.4s)---also uninstalled and reinstalled the benchmarks.
Upped voltages for everything....
It's like it hates my 9700Pro which is a Rev 1.3 card and I've never had it not get along with everything.
Anybody had problems with 9700Pros and this or a similar P series or other MSI board???
Suggestions??
Solutions??
Thanks-----John

Quote
Originally posted by NovJoe
True... Many users has feedback with regards to the ATI Revision problem, but nothing has yet come to light since some with ver 1.2 works fine too. Some also mentioned about the different catalyst used and recommended Omega(I think so...) Catalyst. In the end all comes down to luck with Trial and Error kinda stuff. Seems like that's the reason why the nVidia community is still large as they works fine on most systems.
I used to ONLY use Nvidia....
Then I paid a ton for a Ti4600 and was .....well---let's just say I was underwhelmed.....
Tried ATI's 9700Pro----and was scared to death of ATI's drivers....
But----put the thing in----loaded drivers and......viola----the thing ran beautifully----the graphics were gorgeous----and I've not gone back to Nvidia since.
My ATI 9800Pro is superb and my 9800XT is outrageous.....
But I get tired of the same companies after a while and will probably try an Nvidia PCI express card----whenever they come out and PCI express is solid.
I LOVE the competition between the two companies.....better for all us enthusiasts!
John

Laserjet m276nw won't go into eco mode

Hi all,
For some reason my new printer won't go into eco mode. I've doubled checked the settings and even though it's idle for days the touch console is always on and it never enters sleep mode.
Any idea how to fix this? I've checked the settings via the Web interface and the touch console and they both have this mode enabled. I'm afraid if this keeps up it'll burn in the console UI and use a lot of electricity.
Thanks.

Hi @Mkakers,
I understand that you are having issues with the printer not going into sleep mode. I would like to help you resolve this issue.
Make sure the printer is connected directly to a wall outlet. (don't use a power hub or a surge protector) This ensures the printer is receiving full power and may help this situation.
I have provided the menus for the sleep modes, just to double check the settings again. This information was provided by the manual on page 139. LASERJET PRO 200 COLOR MFP.
Set the sleep delay:
1. From the Home screen, touch the Setup button.
2. Open the following menus:
● System Setup
● Energy Settings
● Sleep Delay
3. Select the time for the sleep delay.
NOTE: The default value is 15 minutes.
Set the Auto Power Down delay:
1. From the Home screen, touch the Setup button.
2. Open the following menus:
● System Setup
● Energy Settings
● Auto Power Down
● Power Down Delay
Update the printer's firmware if the issue continues. HP LaserJet Pro 200 color MFP M276nw Drivers.
What operating system are you using? How to Find the Windows Edition and Version on Your Computer.
How is the printer connected? (USB/Ethernet/Wireless)
If you need further assistance, just let me know.
Have a great day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

I followed the Clear CMOS Ram guidelines but I can't get into Setup!

hey folks, thanks loads for the guildlines in the stickies, I followed the one for removing the battery to clear the CMOS RAM, and when it gets to the point where I press F1 to continue or DELETE to enter SETUP, whichever I press it just takes me to a blank screen with a flashing cursor in the top left corner (i think its the _ symbol or the -), and when I reboot I have to repeat the process of the monitor won't come on properly. If I just press DELETE to go into SETUP before the error comes up it does the same thing but theres a thick blue line at the bottom of the screen too.
Any clues?
Specs: 64MB NVidia GeForce 2 MX440 AGP 2x
512MB 2100DDR RAM
80GB HDD (Matrox i think?)
AMD Athlon XP 1800+
Mobo: K7N2 Delta2-LSR specs on here: http://msicomputer.co.uk/Products.aspx?product_id=703554&cat_id=77
any help would me so appreciated as i'm at the end of my tether now!
cheers
alex

Hello, thanks all for your reply.
I did notice my card is 2x and technically the board is 4x/8x, I read up on the AGP thing and it seemed very likely that it would work anyway. Am I stupid for thinking that it would work? Why would there be a checksum error because of that though?
Anyway, in answer to the original question I needed to boot from CDROM so I could format and install Windows XP on my hard drive so I entered the setup and changed it to boot from the CDROM first, there was also a section I changed from Manual to Auto - I can't remember specifically what it was for, but they were exactly the same anyway, I think I left it on Auto as that always went for the most stable option and I really wanted to avoid any trouble (ugh!). Either way, like I say it didn't change any settings anyway so I don't see how it could be that.
So I posted on Driverheaven.net here: http://www.driverheaven.net/showthread.php?t=102308
They suggested I clear CMOS and thats where I am now!
Thanks for the replies, any more ideas?

MSI 865pe neo 2 - BOOT FAILURE PROBLEM

i have a msi 865pe neo 2 motherboard and im getting the following problem, when i turn on my pc it is coming up with boot failure message and ask me to restart my computer it goes through this a lot then all of a sudden it works fine , when this problem happens and i go into cmos settings i notice that it is not reconising my IDE hard drive PLEASE PLEASE can someone help me with this and tell me what the cause is and how to fix it.
Many Thanks
Simon Rogers

im sorry here is the spec of my machine, and the problem is listed in my original post please can someone help
Motherboard - MSI 865pe Neo 2
CPU - Intel Pentium 4 2.8 GHZ Prescott
Hard Drive - Maxtor 6E040L0
Memory - x2 512mb Crucial DDR PC3200
Graphics card - Nvidia GeForce Ti 4600
Sound card - Creative labs live 128
CyberDrv CW038D CD-R/RW
Sony DVD RW DW-G120A
PSU 400 watt

MSI 865PE Neo Series Restart Problem

Hello,
I have a problem on my MSI 865PE Neo Series Mobo when i restart my system using windows or by pressing ctrl+alt+del my pc won't restart and stay there forever on a black screen but when i press my reset button it will restart normally this is my one and only problem regarding this mobo... pls any help here. fix or any tips and suggestions...
(*by the way this is just my friends computer and im the one who builds it and maintain it...)
System Specs Of My Friend's PC:
MSI 865PE Neo Series Intel P4 Motherboard w/ HT Technology Support
Intel P4 @ 3GHz/800MHz FSB HT Technology
512MB DDR400
MSI NVIDIA GeForce FX 5700 @ 256MB DDR
550W PSU 12A-30

no guyz im using Windows XP Pro SP1 and its not a OS problem because the first time i boot the system i have no OS yet and then i press ctrl+alt+del then my system wont restart at all even in windows ive updated all drivers and mobo bios and increasing DDR Voltage to 2.8v and disabling HT has no changed at all any help would be appreciated... i think this is some problem with MSI mobo power management that it can't match ur psu so well unlike ASUS and GIGABYTE mobo runs perfectly fine. by the way its not my pc its my friend's pc and im the one who builds and hope to fix this one and only problem... everything else is ok except for the Restart Problem!!!!
My System Spec:
GIGABYTE GA-8INXP Intel E7205 Chipset P4 MB
Intel P4 @ 3GHz/500MHz FSB
1GB Dual Channel DDR266
ASUS ATI Radeon X800XT @ 256MB GDDRIII/AGP8x
Seagate 80GB SATA HDD
Maxtor 80GB IDE RAID HDD
Microsoft Windows XP Professional Edition @ Service Pack 2 RC1 (fully updated)
My Friend's Spec:
MSI 865PE Neo Series P4 MB
Intel P4 @ 3GHz/800MB FSB
512MB DDR400 CL2.5
MSI NVIDIA GeForce FX 5700 @ 256MB DDR/AGP8x
80GB IDE HDD (x2)
Microsoft Windows XP Professional Edition @ Service Pack 1 (fully updated)
*this is not a windows problem motherboard power management or bios settings bug here..
*its my first time to handle a MSI Motherboard
*and if any guyz out there need help regarding other problems or any problems in ur pc pm me in ym @ [email protected]

MSI 865PE Neo-L high temp readings?

Hello..
When my system is off for a couple of hours and then i boot up my system,and go directly into the bios,my CPU temperature is already 40-45C° !!! :O
And even my cooling block isn't hot then(not even warm).
Also in windows with the MSI software i get those high temperature readings.
Only with speedfan,the temperatures are more normal.
Is this a know issue that MSI boards have high temperature readings ?(
CPU is a P4 2.6Ghz FSB800
(system is not overclocked)
Thanks in advance! :D

ok,first of all thanks for the reply's guy's!!!
My system specs :
MSI 865PE NEO-L (duh :D )
P4c 2.6Ghz FSB800 with boxed cooler.
Maxtor 30GB 7200RPM
2x256 DDR400 ram
GF4 TI4200 64mb
Q-tec 400W dual fan.
DVD drive (lite-on 16xdvd ,52cd-rom)
CDRW drive(lite-on 52-32-52)
As said,with corecenter or other MSI software almost directly 45C° Even the heatsink is not warm then.
(stressed 58-60C°)
Speedfan gives me more then one temp..
HD0 : 23C° this should be the harddisk temp i think.
Temp1 : 29C° this should be the system temm or case temp.
Temp 2 : 42C° this should be the CPU temp.
All these readings are IDLE temps.
And i think those are the wright temps...
(ps,sorry for my bad english,if you don't understand something,please ask :D )
And Naviblue,nice overclock you got there!

HT201272 So I preorered an album from iTunes and now it won't download into my libraray. It says that I purchased it on iTunes, but it won't even show up in the "Purchsed" library in my account. Does anyone know what I am supposed to do to downlaod it?

So I preorered an album from iTunes and now it won't download into my libraray. It says that I purchased it on iTunes, but it won't even show up in the "Purchsed" library in my account. Does anyone know what I am supposed to do to downlaod it?

If you can't enter the passcode then you have to place the iPod in recovery mode and then restore the iPod via iTunes. For ecovery mode see:
iPhone and iPod touch: Unable to update or restore
Note that this requires using the sleep/wake button. If you are not successful then there is nothing else that I know you can do.

My ipod won't go into disk mode

i've tried and tried and it won't go into disk mode. it shows an apple then a folder with the ! and when plugged into the computer sometimes it'll say don't disconnnect for about 10 seconds and then it'll go back to the apple.
also it sounds as though the drive is stuck in a loop; a weird repetitive whirring sound when i hold it up to my ear.

If you can't get it into disk mode and restore the iPod it most likely needs service, especially with that noise it's making.
Service request.

HT201263 What if my ipod touch won't go into recovery mode because it is pw locked?

What if my ipod touch won't go into recovery mode because it is pw locked?

Go into Recovery Mode per the instructions here.

My iPod classic won't go into disk mode

I have an iPod Classic (120GB) here. When I turn it on, it gives me a screen with the Apple logo first and after a few seconds a screen with a red circle, a cross in the circle and the text: www.apple.com/support/ipod . I followed all the steps on that page, however my iPod won't go into disk mode. The iPod is not seen by my iMac and iTunes. What to do?

See Here
iPod doesn't appear in iTunes
From Troubleshooting Here
http://www.apple.com/support/ipodclassic/
iPod issues? Try these five steps first: Reset, Retry, Restart, Reinstall, Restore.

Word attachments won't open into Word application

My dad complained that his iMac G5 opens Word attachments automatically into the trial version of MS Office Word.
Eventhough he purchased a copy of Office, Mail continued to open Word attachments to the trial version. Because the trial version of Office is expired, the attachments wouldn't open unless I dragged the docs unto the desktop and changed the Info on the documents to open with the purchased version of Word.
In one attempt to resolve the problem, I trashed the trial version, Mail popped up the dialogue box that asked what application did I want to open the attachment with. I chose the purchased version of Office, but Mail won't do this automatically. It still asked to choose the application to open the document.
I went into his Documents folder and picked one Word doc to change the Info @ "Open With" and chose MS Word app and checked the box "Use this application to open all documents like this." Still didn't work. I then manually changed the Info in all of his Word docs to open into the purchased version of Word. Problem still not resolved.
Found out that his PDF docs won't open into Preview automatically too! I get the dialogue box... "Choose application to open document."
I looked through Preferences and couldn't find a solution.
I'm the family IT, and I need help.
I need Mail to open attachments automatically into their correct applications.
Thanks, Joe
PowerBook G4 12" Mac OS X (10.3.7) 1.33 GHz 512 MBRAM

Per this link, you must uninstall the Office 2004 trial or Test Drive version before installing the full purchased version.
http://www.microsoft.com/mac/default.aspx?pid=office2004td
Since you have already uninstalled the Test Drive version, I suggest uninstalling the full purchased version and then re-install it.
Regarding the problem with PDF documents, this link may be helpful.
http://www.thexlab.com/faqs/resetlaunchservices.html

865PE Neo 2P won't go into SETUP.. DHCP??

Similar Messages

Maybe you are looking for