865PE Neo2-PFISR problems after power outage

I need some help with a problem. A recent power outage while my supposedly "surge protected" 865PE Neo2 based machine was running, apparently messed something up. After our power came back on, I powered it back up and discovered that I now have 4 ongoing problems. Problem 1) it now hangs twice during the boot process, once at "auto detect 3rd master - press escape to abort", which if I then press ESC, it then moves to "auto detect 3rd slave - press escape to abort" and hangs there until I press ESC, at which time it then finishes booting like normal. (by the way, I don't even have any 3rd master or 3rd slave installed) Problem 2) I can no longer enter the Bios setup, even though I press the DEL key at the appropriate time. Problem 3) The case light for hard drive activity stays on constantly, even though the drive seems to be working normally without any other problems. Problem 4) A few issues here. My sata dvd/cd combo drive is no longer recognized as being installed; the activity light on the drive is constantly on even though the drive is not running; the drive bay will no longer open.
I'm guessing that something has possibly been damaged on the motherboard or maybe the bios was affected somehow, or maybe the power supply was somehow damaged. Either way, I'm not sure what to do now. With the exception of the problems I listed, my system otherwise works normally as it always has, with the only real downside being that I don't currently have a dvd/cd drive. I haven't tried any troubleshooting myself because I'm not sure where to look or what to look for. The specs for my system are listed in my signature, with the only change being that I'm still running the original Antec 350w power supply that came with the case. I could sure use some expert advice and help with this.

Problem Update.
Well, I finally got my machine up and running "almost" as good as it was before my power surge problems. Thank you to everyone that responded with advice. I ended up replacing the Antec 330w TruePower psu with the new Enermax Noisetaker 420w (EG425P-VE SFMA V2.0) that I had, and I had to replace the MSI sata combo drive (went with a Pioneer 710 DVD-RW, which is an excellent unit) and now things are back to normal. Plus, I bought an APC 650VA/390watt battery backup with soft shutdown to help prevent any power outage problems again.
When I said "almost" as good as new, that is because this morning when I booted up, all I got was a black screen (no post) for a couple of minutes, and then a message appeared that approximately said "the dram timings are too tight, reload timings", or something like that. Well, since the timings have never been changed, I'm not sure what is going on, but after turning it off and then re-powering it up again, it booted (though slowly at first) and I've just been letting it run all day. Ha, just when I was ready to venture into OCing this rig. Think I will anyway. If the problem continues, I'll be back seeking helpful advice again.

Similar Messages

Problem with NIC and Firewire on MSI 865PE NEO2-PFISR

Hi, I have lots of trouble getting the network adapter on the MSI 865PE NEO2-PFISR to work.
The NIC's LED indicators doesnt even light up when I plug in a network cable,
and in windows (win 2003 server) it doesnt find the adapter at all.
The NIC is displayed in the bios, and I have the option to disable it,
but it is enabled.
I have even reinstalled windows 2003 server to try to get the NIC to work.
I have upgraded the bios to v3.8 via live update, with no problems, although the
firewire-option on the same page in the bios is still gone, it doesnt detect the
firewire at all(!).
I have also tried several other NIC's (a 3COM 3C905B TX and a 3C905B TX XL
PCI adapter). The 3C905B TX worked fine for a while, and then it started saying in
windows that a network cable was unplugged, and began to try 10mbit, 100mbit
lots of retries, now it doesnt work at all.
I swapped tp-cables and changed the ports on the network switch (which there is
also other computers attached to which doesnt have any problems) and that didnt
made any difference.
It seems that the whole pci bus is long gone, and maybe the onboard NIC is
attached to this same pci bus?
Strange also about the firewire-controller which isnt detected anymore.
The USB devices work, and even a 3com usb wlan adapter works well.
I have tried to reset the bios several times without that making a difference.
Anybody have a clue to point out here?
Cheers!

Quote
Originally posted by Raven
you could try and flash to an older bios
I tried most anything on flashing bios, both to a lower and a higher version.
I returned the motherboard to the reseller and got a new motherboard as a replacement. This doesnt have all the same problems. At first it didnt post at all, indicating to red lights on the diagnosis.
Then I was so pissed I hadnt touched the computer in a week, and just tried to use it a few days ago, and it seemed to work all ok. I used it for a few hours, and then it locked up.
When I powered it up again, the lights on the integrated adapter was out. At first it seemed to work to take the agp card a little out of its slot, as if it was unaligned or something. Used it for a few more hours.
Then I plugged in the sound cables (5.1 sound with 3 cables), and with the last cable, the network darkened out AGAIN!!
In the bios it still indicates that the network is enabled, firewire is enabled etc.
I twisted the network cable, and for a few microseconds I get a orange light, not the usual green light. Now this has stopped too.
I see other also have problems with these symptoms so I guess I've got another black monday card.
I will return this card too, and ask the reseller to get a card of another brand.

865PE Neo2-PFISR failure

Hello,
This is my first post here so I would write down my system configuration at first:
my MSI mobo: 865PE Neo2-PFISR (with BIOS update to V3.A since 21/01/2005)
CPU: Intel Pentium 4 HT 2.8E SL79K
RAM: 2GB Kingston 400MHz DDR (4 x KVR400X64C3A/512)
Graphics Card (GPU): Club ATI 9600XT 256MB AGP 8x
2 SATA HDDs: 320GB + 160GB Seagate Barracuda 7200rpm
3 IDEs: SONY DVD-ROM 16x, PLEXTOR CD-RW 52x, NEC DVD-RW DL 16x
Sound Card: TASCAM US-122 (External USB)
Power Supply (PSU): Seasonic S12+ 550W 80plus (+3,3V@24A, +5V@30A, +12V@18A, [email protected], +5Vsb@3A) http://www.seasonicusa.com/s12plus.htm
Monitor: EIZO L550 17" LCD with DVI cable connected
O/S: Dual boot on Kubuntu 7.10 and Windows XP (separately in each HDD)
using BIOS IDE setup: Native Mode configuration with S-ATA only, both P-ATA keep Enabled and no RAID which is the only configuration that my Linux installs or starts and USB Legacy Disable for starting a Windows XP installation otherwise it crashes after a CD-ROM boot in the first blue LOAD screen of the bootable Windows XP.
so I would like to discuss the failure problem that I have:
Sometimes I push the pc's power button to power on and the system gives power to the peripherals (CDs, HDDs, FANs, etc) but the screen does not open at all and the front HDD's orange led stays always ON still. The "D-Bracket 2" shows at once started 2 green leds (2nd and 3nd) and two yellow (?!?!?!) or 2 red (2nd and 3rd) and two yellow (?!?!?!). I'm surprised about the yellow!!! I tried out several setups after failure like: barebone, just the CPU installed with no memory, GPU or HDDs etc, another different type of PSU or unplugging any cable (from the USBs' or the D-Bracket's to the Power/HDD/Reset Leds and the FANs') but nothing changed at all. Finally if I "Clear CMOS" using the Jumper JBAT1 as the manual's information, everything goes well and the pc starts excellent again but then, in a random time after a power on or a restart it does the same failure. I do this post because this was happening really rarely in the past but now this is happening usually (once in a week I can say) with no hardware change since a while. Thank you in advance for your time and I will be thankful for any help.
I'm sorry for my bad English.
Greetings from Greece
Christos Kyrkilis

Quote from: Del UK on 07-February-08, 04:31:04
You have HSF that has retention socket with back plate
Have you done a strip and reassemble of this as yet..........
Could you please rephrase what you've posted cause my bad English couldn't help me understand what you mean. Sorry

[865PE NEO2 PFISR] Won't boot with added memory

Recently I upgraded a few items on my PC which has been running fine for 18 months or so. I changed out the video card and bought double the memory of the same brand and type it had in it. I went from 1gig (2 sticks) and added two more sticks. But now it won't boot. The power is on but no output whatsoever.
I RMA'd the memory thinking that might be the problem but it's the same with the new set. I tried all sorts of memory/slot combos. Basically, the new memory works fine if you swap it out in bank A with the old stuff. That's how it's running right now, so I know all of the sticks are good. I can take a third and put it in either slot bank B and it'll boot, but obviously not run properly. But any combination of these four sticks and the system won't boot!
Please help!
I'm running this system:
Win XP (SP1 I believe)
865PE NEO2 PFISR
P4/3.0CGHz, 800M 478P/512K HT
DDR Corsair 512MB X4 (400)
Dual 80gb samsung HDs running SATA
Sapphire X800GTO 256M video card
Antec Sonata case
TruePower 380Watt ATX12V

What brand, model, and speed are the RAM sticks. Did you check your Test Report booklet which came with the mobo. If you can't find it, you can go to the MSI website and look for your MOBO and get the test report that way. Some brands/models will that have been tested are shown in the report to be okay in all 4 slots, some only test okay in 2 or 3. Check this report and if it is one of the brands/model/speed tested you will see how it fared. It may well be you the MOBO doesn't like your RAM in 3 or 4 slots.
Maybe I missed it, but did you try each slot with only one stick at a time? You may also have a bad RAM slot.

E4500 firmware corrupt after power outage

Latest firmware with CCC corrupted after power outage. I reseet the e4500 several times and tried to reload the firmware and still no good. Only way I got it back up is to install the older non-CCC version 2.37. Strange all was fine until the power outage. Not sure if I should even bother to upgrade to 2.38 again.

Yes, power outages may caused some damage either on the hardware or software of the any device especially if there's some activity going on inside the device the time of the interruption. If everything is fine with the old version then there's really no need to update it but if you've noticed some issues, better upgrade to the newer version so to fix any problems.

My AppleTV stopped working after power outage. Light is on and I rebooted and reset w remote but it keeps giving me a pic of the Hdmi cord like it is not recognizing the hdmi as being plugged in. I've unplugged it several times.

My AppleTV stopped working after power outage. Light is on and I rebooted and reset w remote but it keeps giving me a pic of the Hdmi cord like it is not recognizing the hdmi as being plugged in. I've unplugged it several times.

It is in recovery mode. The picture is telling you to connect to iTunes via micro usb cable in order to restore.
http://support.apple.com/kb/HT4367?viewlocale=en_US&locale=en_US

Hyper-V - virtual machines don't start automatically after power outage

Hi,
I have a HP server running Windows 2012 R2 + Hyper-V. On this server, four VM have Windows Server 2003 R2, and one VM has Windows 2012. After power outage, 1 2003 R2 VM and 1 2012 VM are started properly, but the other three machines aren't. I've started
it manually. All VM's have last version of Hyper-V integration tools installed, the option "Automatically start VM if it was running before the service was stopped" was chosen. I'm not very familiar with Hyper-V, so, I've investigated only Hyper-V-VMMS
event log. There are some recurring errors:
The Integration Services Setup Disk image could not be updated: The process cannot access the file because it is being used by another process. (0x80070020).
and
Failed to get the disk information.
But I think it isn't a clue.
How can I clarify, why these machines aren't started automatically?

Hi EugenBerend,
Maybe it is related to system resources allocation during the start up .
I would suggest you to configure a startup delay for those lower priority machines so that system
can locate enough resource for them.
Hope it helps
Best Regards
Elton Ji
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Lion server : local user account disappear after power outage

On the server computer.After power outage I restart server the machine starts up ok.At login screen local user name disappear but there's others account same as client computer.I can log in to network account but can't log in as local.
In sytem preference local user account is still there.
I don't want to reinstall lion server .
What can i do now?
Thank you for your assistance.

It sounds like the user directory is damaged. You might try booting into the recovery partition, running Disk Utility, and doing a Repair Volume (and maybe a repair permissions) on the server volume.

Mac Mini wont start after power outage, and problem copying iPhoto library. HELP!

    So, recently there was a power outage in my neighborhood, the power was intermitent for about 2 hours, during this time my mac rebooted itself several times, but on the second time it rebooted the power went out during boot, then the power finally went out for good, it was back in about 3 hours, but when i finnaly turned on my mac it got stuck at the Apple logo with a spinning wheel and a progress bar that wouldnt go past 40%, when i boot holding command -v it said that there were a lot of errors which were automatically fixed, except for one, "Incorrect Thread records" or something like that.
    I have another partition with Mountain Lion installed for emergencies, the other one with Lion became inaccessible to mountain lion or any other OS X version, but oddly enough, I can access my Lion partition via HFSexplorer and see all my files untouched.
    My main concern are my pictures in iPhoto, and thats about 36Gb of data, I want to backup them to my windows pc by copying the whole iPhoto library package, but HFSexplores for some reason cant copy the folders with date (XX/XX/XXXX) with the /, and it keeps changing them to XX_XX_XXXX and I know that would pretty much break my iPhoto library!
I googled my drive problem and people said that I need a Disk Utility called DiskWarrior, but I cant seem to find how to to use it, I got a copy from a friend, it was the digital version of the boot disk which need to be burned to a dvd.
Any help would be appreciated, and sorry for the bad english

OK, we need more info about your Mac. Do you know how much RAM it has in it?
If you don't know the model, find the Serial# & use it on one of these sites, but don't post the Serial# here...
http://www.chipmunk.nl/klantenservice/applemodel.html
http://www.appleserialnumberinfo.com/Desktop/index.php
How to find the serial number of your Apple hardware product...
http://support.apple.com/kb/HT1349

Problems erasing HDD after power outage.

Sold my old MacBook Pro and want to erase the HDD. While erasing the HDD during the night I had a power outage and the MacBook ran out of battery before completing the task. I can't resume the erase since the HDD will not unmount. Any suggestions would be greatly appreciated. ThanksProblems

You erased it. Of course it will not mount. While it may not have removed all the 1's and 0's you put on it, it got well paste the beginning of the disk where the file system superblock was located, so as far as Mac OS X is concerned, there is no valid file system on this disk.
Can you use Disk Utility -> Select the disk -> erase tab -> erase button, and erase the physical disk that way.

865PE Neo2-V problems

I'm hoping this is the right area to ask for help... Ever since I got this MB it's been nothing but trouble. I bought it, took it home, hooked it up, no power. So I went back to the computer shop I got it from and asked them what's wrong with it. After taking my system in for them to make sure it was setup right, they informed me that I had to send it back for RMA work. so now, about 2-3 months later I finally got a new board back, and have random reboots. I've tried everything I could think of to figure out why it's randomly rebooting and am stumped. One surefire way to make it reboot is opening the front of my case, that does it everytime, so I tried a different MB to see if the same problem happen. It doesn't... Was there a re-call or something on these MB's? I hate to do another RMA and be without a computer for a few more months, since I work out of my home, and my computer is a main part of my work... I can't afford to send this MB in again. I've got the latest BIOS update, my RAM is set to 2.5,3,3,8 (per manufacturer). I have a 2 gig P4, that works fine in my other board. Even bought a new SATA HD for a fresh install of windows XP and still, the random rebotos happen. I'm not trying to OC or anything along those lines, since the chip I have shows almost no increases from OC's, so it's not from OC'ing it.. I'm running a 480 watt power supply, and that should be more then enough juice for the board... Sorry to rant and rave, but been working on this for about 3 weeks and about to pull out all my hair, since everytime I think it's going to be ok and I start to actually accomplish some work, it reboots, before I have a chance to save anything...
I guess I'm asking if anyone else has had these problems with this MB, or do I just have that kind of luck? I've been looking over the boards here for the last week or so and tried pretty much everything I've found, under a search for random reboots, to no avail. Here's a list of what I can think of off the top of my head that I've tried... <deep calming breath> Changed the BIOS through every version since the initial BIOS the driver disk has on it, re-seated the RAM in different places in the DIMM's, Memtest388 or whatever it is with 0 errors on a 10 hour test (the longest it's run without a reboot since day 1), pulled the graphics card and re-seated it, put more fans in, taken them out, took the power supply in to have it tested (it's fine), replaced the RAM with new shiny RAM that's tested fine, tried a different case, reset the CMOS, tried a different chip, tried numerous power supplies, checked the voltage at the surge protector, replaced all old components (CD drives, floppy drives ect...) traced each individual wire checking for breaks insulation problems, software tests out the wazoo all saying it's fine, new heat sinks, new thermal gel, put the computer on top of a cold vent (thinking of might be to hot) and so on... I guess I should list my setup since every component in the case has tested out fine at the shop and I can't afford to replace anything else...
865PE Neo2-V MB with a Intel 2.0 gig P4
512 x2 corsair VS512MB400 RAM sticks
Asus N6600 graphics card (Nvidia)
480 watt power supply
Sound Blaster live! 5.1 gamer
BIOS version 6.2
At first I thought it might be overheating, but the processor and RAM stay around 37º and 39º give or take 2º. I've also checked for virus's/spyware/adware to many times to remember with none found. Any help would be greatly apprieciated before I get so fed up that move to a cave and rely on an abacus for record keeping...

I have almsot the same set-up as you have.
I didnt have these problems though.
One thing that comes to mind is a grounding error.
Have you checked the space between the motherboard and the side of the case its mounted to?
I read that you tried a diffrent case, but it could be some issue with one of the grounding points where you put the screws in perhaps.
I know that the Spread Spectrum setting in BIOS can cause some disturbances, but it shouldnt really be enough to make it reboot though.
But check that one anyway, ON and OFF.
A bit info on Spread Spctrum:
"Spread Spectrum
When the motherboard’s clock generator pulses, the extreme values (spikes) of the
pulses creates EMI (Electromagnetic Interference). The Spread Spectrum function
reduces the EMI generated by modulating the pulses so that the spikes of the pulses
are reduced to flatter curves. If you do not have any EMI problem, leave the setting at
[Disabled] for optimal system stability and performance. But if you are plagued by EMI,
activate the Spread Spectrum for EMI reduction. Remember to disable Spread
Spectrum if you are overclocking because even a slight jitter can introduce a temporary
boost in clock speed which may just cause your overclocked processor to lock
up. Options: [Disabled], [Enabled]."
I assume you tried to run the Load BIOS Setup Defaults.
Also make sure that all the jumpers on the motherboard are set right, there might be some of the set wrong by accident, check with your manual to be sure.
You can try this to, take out your motherboard and place it at a non-conductive material.like wood or glass and attach all the components u need to do a boot-up, and only those, and see whats happening.
If it runs ok like this, then it might be some sort of short-circuit somwhere.
I think i read about an ASUS board that had some components near the CPU that somehow got in touch with, either the heatblock, orsome connection point of the fan-mounting and it caused some serious problem for people.
I took quite some troubleshooting to find that out for them.
All i can think off right now, at the top of my head, but try this, if you havent done it already.

865PE Neo2-V problem/bad BIOS ver. 6.2

A new BIOS for the 865PE Neo2-V has been posted at http://www.msi.com.tw/program/support/download/dld/spt_dld_detail.php?UID=612&kind=1. This BIOS did not work for me and I had to revert to version 6.1. If you plan a BIOS update, make sure you keep your previous version handy!
Symptoms: after the flash, the system would not post. I had an 8-beep error code (video problems on AMI BIOS). Removing either or both video cards did not help, neither did the usual (re-set BIOS by jumper, remove battery, remove RAM, disconnect HDs, etc.) Using the recovery flash method (place BIOS file as AMIBOOT.ROM on a floppy) with version 6.2 resulted in the same issues. Recovery flash to version 6.1 and all worked fine again.
System specs (if more details are needed I can provide them, I'm not at the system in question right now).
865PE Neo2-V (MS-6788)
2x 512MB RAM (Corsair? I would need to dig for specifrics)
NVIDIA GeForce 6800GT in AGP slot
NVIDIA GeForce FX 5500 in PCI
(plus a bunch of HDs and USB devices, but this problem occured even with all this removed).

Quote from: crazy on 28-February-06, 08:36:40
I just want to ask one question: you said that after you flashed the bios to the 6.2 version, then it could not even boot. Thus could you tell me how could you flash the bios to 6.1 version?
There is a way to flash the BIOS even when the system won't boot. For AMI BIOS (as on this board):
1- Format a floppy, and copy the BIOS file to it.
2- Rename the BIOS file to AMIBOOT.ROM
3- Put floppy in the drive.
4- Power up system while holding CTRL-HOME
5- Wait until you hear floppy drive access, then you can release CTRL-HOME
6- When you hear 4 beeps, the BIOS had been flashed from the file on the floppy.
7- Power off, reset BIOS by jumper (just to be safe) and then power up again.

Cannot login to my usual account after power outage

Had two power outages last night; machine survived the first one, but after the second outage and restoration I cannot get in to my usual user account. What happens:
Grey apple screen, normal
Blue screen with progress bar indicating that OS X is loading... before the indicator fills all the way to the right, it exits to a blue screen [of death] with a mouse cursor (which works) and just stays there. It goes no further. Rebooting obviously does not fix it; I rebooted a dozen times trying to get beyond that.
What I've tried that hasn't fixed it:
Rebooting
Unplugging and replugging, both computer side and wall
Repairing both the disk and permissions--done, no effect
Safe booting and attempting to log into the account under a safe boot--it loads the wallpaper and hangs right there, no dock, no menu loaded
Removing the User/~ Preferences folder
I believe that what is causing the problem is some login startup item. However, since I cannot even log in in Safe mode, I can't start the System Preferences Accounts panel to remove login items.
Question: Is there another way to remove the login startup items? Removing the Preferences folder has not helped. I'm missing something. What is it?
I can log in to any other user account. I am currently in Root.

From the root account, open the Accounts pane of System Preferences and delete the login items for your normal account; an admin account should be able to do this for any account on the system, while non-admin accounts can only be used to change their own login items.
If removing the login items does not fix the issue, remove other parts of the home folder until you are able to log in to that account. If you've removed/renamed the entire home folder and aren't able to log in successfully, check that the permissions on the hard disk allow all accounts to read it; if you still can't successfully log in to that account, restore a previous version of the NetInfo database.
(14837)

865PE Neo2 -FIS2R Problems

I purchased a brand new MSI 865PE Neo2-FISR along with a P4 2.4C(OEM), a Thermaltake Spark 5c cooler and a Corsair XMS Twinpack(TWINX512-3200C2PT) of DDR400 memory.
The install went fine, the system booted and ran very well right out of the box. I installed the Live Update program from MSI and it updated itself. I then used that utility to generate a BIOS flash/recovery disk to update the bios from 1.10 to 1.30. The update worked fine and I rebooted the machine into Windows XP with no problems.
I then decided to do some tweaking in the new 1.3 BIOS. After several unsuccessful memory/Dynamic Overclocking settings the system refused to boot. I tried the Clear CMOS jumper to reset the defaults but it still would not boot. I checked the D-Bracket, 3 red 1 green(lower right) which indicates that the video card is not initializing. I attempted reseating the video card (a PNY Geforce4 TI4200) with no luck, I then replaced that card with a GeForce4 MX440 SE with no luck. I tried four other video cards, 2 AGP and 2 PCI, with no success.
At this point I pulled the board out of the system and let it sit with the battery out of the board hoping that the BIOS would reset to default values. I reinstalled the board with all the hardware and again the same D-Bracket error with no video generated. I tried different arrangements of memory using the new Corsairs and various other DDR333 & DDR266 again no luck.
What is going on with this thing? How could an errant timing change completely lock out the VGA card? And why can I not clear the settings to allow the card to initialize?
This thing is getting RMA'd soon if I can't find an answer.
Anyone have any ideas or similiar troubles? X(

Quote
Originally posted by gary172
Another thing I don\'t understand about all the isses with BIOS 1.3, performance, RAM and timings etc, is - How can the 865PE Neo2 - FIS2R pretty much come out at the top of the heap in Tom\'s Hardware Test:
\"The board therefore achieves the best performance in the whole test field.\"
http://www6.tomshardware.com/motherboard/20030707/i875p-46.html
with MAT and DOT enabled, without any apparent negative reports of stability.
Is it that he used a Beta Bios: V1.3B3 (06/12/2003)
Or was his MSI board a \'pre-press release\' mobo similar to the ASUS board and the production versions we are buying are missing certain components?
http://www6.tomshardware.com/motherboard/20030603/865_PAT-06.html
Or did he have \'hand picked\' memory from Corsair \"2 x 256 MB, Corsair PC3200 TwinX\" and didn\'t report it?
There are a lot of reviews lately that have it as one of the fastest MB's around at the moment, here are a handful I found:
http://www.mbreview.com/neo2pe-10.php
http://www.thejemreport.com/reviews/865peneo2.htm
http://www.hardwarezone.com/article...&aid=795&page=1
http://www.hexus.net/review.php?review=564&page=1
http://www.pcstats.com/articleview....eid=1402&page=1
http://www.techview.nl/reviews/2959

Lost my pictures in iPhoto '08 after power outage

Hey-
Last night i was organizing some events, it was late and i put the computer to sleep with iPhoto still open, around 3 am there was a power outage. This morning, when I turned on the computer and opened iPhoto, it was totally empty. Does anyone know how to get my pictures back? Thanks!
Adriana

Welcome to the Apple Discussions. To protect yourself from a similar problem in the future see the tip at the end of my signature below:
TIP: For insurance against the iPhoto database corruption that many users have experienced I recommend making a backup copy of the Library6.iPhoto (iPhoto.Library for iPhoto 5 and earlier versions) database file and keep it current. If problems crop up where iPhoto suddenly can't see any photos or thinks there are no photos in the library, replacing the working Library6.iPhoto file with the backup will often get the library back. By keeping it current I mean backup after each import and/or any serious editing or work on books, slideshows, calendars, cards, etc. That insures that if a problem pops up and you do need to replace the database file, you'll retain all those efforts. It doesn't take long to make the backup and it's good insurance.
I've created an Automator workflow application (requires Tiger or later), iPhoto dB File Backup, that will copy the selected Library6.iPhoto file from your iPhoto Library folder to the Pictures folder, replacing any previous version of it. There are versions that are compatible with iPhoto 5, 6, 7 and 8 libraries and Tiger and Leopard. Just put the application in the Dock and click on it whenever you want to backup the dB file. iPhoto does not have to be closed to run the application, just idle. You can download it at Toad's Cellar. Be sure to read the Read Me pdf file.
NOTE: The new rebuild option in iPhoto 09 (v. 8.0.2), Rebuild the iPhoto Library Database from automatic backup" makes this tip obsolete.

865PE Neo2-PFISR problems after power outage

Similar Messages

Maybe you are looking for