871w wireless configuration
Hello,
I know this question was asked many times, but I'm still not able to finalize my configuration on 871w. LAN part works fine, but wireless clients do not get DHCP IP. here is the config:
Building configuration...
Current configuration : 2092 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname WROUTER
boot-start-marker
boot-end-marker
logging message-counter syslog
logging buffered 4096
no aaa new-model
dot11 syslog
dot11 ssid sputnik
vlan 1
authentication open
ip source-route
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.1.254
ip dhcp pool vlan1
network 192.168.1.0 255.255.255.0
default-router 192.168.1.254
dns-server 167.206.245.7 167.206.245.71
lease 10
ip cef
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
archive
log config
hidekeys
bridge irb
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface FastEthernet4
ip address dhcp
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
no cdp enable
interface Dot11Radio0
no ip address
encryption vlan 1 mode wep mandatory
encryption key 1 size 128bit 0 0D9E3A3AF78EA7A156A6D6FB09 transmit-key
ssid sputnik
speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
station-role root
no cdp enable
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Vlan1
no ip address
ip virtual-reassembly
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.1.254 255.255.255.0
ip nat inside
ip virtual-reassembly
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 dhcp
ip http server
no ip http secure-server
ip nat inside source list 1 interface FastEthernet4 overload
access-list 1 permit 192.168.1.0 0.0.0.255
control-plane
bridge 1 protocol ieee
bridge 1 route ip
line con 0
no modem enable
line aux 0
line vty 0 4
login
scheduler max-task-time 5000
end
I'dliket o have LAN and WLAN clients in same 192.168.1.0 subnet.
Thanks.
This is what I got and it has been working for me. From my modem to my RV016 to my 871w. Once I figure out the PPPOE the 871w will be my only router running, and figure out the port forwarding, but most important I need to configure PPPOE.
mr-r1#sh star
Using 3825 out of 131072 bytes
! Last configuration change at 08:10:30 PCTime Sun Oct 28 2012 by ramosm
! NVRAM config last updated at 08:10:33 PCTime Sun Oct 28 2012 by ramosm
version 12.4
no service pad
service timestamps debug datetime msec localtime
service timestamps log datetime msec localtime
no service password-encryption
hostname mr-r1
boot-start-marker
boot-end-marker
logging message-counter syslog
logging buffered 64000
logging rate-limit 20
enable secret 5 $1$PDK9$YSz8GsnVsDYevR1hVGMG70
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
clock timezone PCTime -8
clock summer-time PCTime date Apr 6 2003 2:00 Oct 26 2003 2:00
crypto pki trustpoint TP-self-signed-3978252741
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3978252741
revocation-check none
rsakeypair TP-self-signed-3978252741
crypto pki certificate chain TP-self-signed-3978252741
certificate self-signed 01 nvram:IOS-Self-Sig#B.cer
dot11 syslog
dot11 ssid ramfam
vlan 55
authentication open
mbssid guest-mode
ip source-route
no ip dhcp use vrf connected
ip dhcp excluded-address 10.25.55.1 10.25.55.49
ip dhcp excluded-address 10.25.55.76 10.25.55.254
ip dhcp excluded-address 10.25.50.1 10.25.50.49
ip dhcp excluded-address 10.25.50.76 10.25.50.254
ip dhcp pool Data
import all
network 10.25.50.0 255.255.255.0
dns-server 10.55.55.1 4.2.2.1
domain-name MR-Lab1
default-router 10.25.50.1
lease 25
ip dhcp pool Wireless
import all
network 10.25.55.0 255.255.255.0
default-router 10.25.55.1
dns-server 10.55.55.1 4.2.2.2
lease 25
ip cef
ip domain name MR-Lab1.com
ip name-server 10.55.55.1
username ramosm privilege 15 secret 5 $1$J2cq$abQJlRlZgmIlEDPX/jd8A1
archive
log config
hidekeys
no ip ftp passive
bridge irb
interface FastEthernet0
description AirNet 1100
speed 100
spanning-tree portfast
interface FastEthernet1
description Extra cat5
spanning-tree portfast
interface FastEthernet2
description Ubuntu PC
spanning-tree portfast
interface FastEthernet3
description PS3
speed 100
spanning-tree portfast
interface FastEthernet4
description Internet Wan Port
ip address 10.55.55.105 255.255.255.0
ip nat outside
ip virtual-reassembly
speed 100
full-duplex
interface Dot11Radio0
no ip address
encryption vlan 55 key 1 size 128bit 0 AB2081CA12B126DD2F95ABCF32 transmit-key
encryption vlan 55 mode wep mandatory
broadcast-key vlan 55 change 30
ssid ramfam
mbssid
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0
station-role root
interface Dot11Radio0.55
encapsulation dot1Q 55 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Vlan1
ip address 10.25.50.1 255.255.255.0
ip nat inside
ip virtual-reassembly
interface Vlan55
no ip address
bridge-group 1
interface BVI1
ip address 10.25.55.1 255.255.255.0
ip nat inside
ip virtual-reassembly
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 10.55.55.1
ip http server
ip http authentication local
ip http secure-server
ip nat inside source list 1 interface FastEthernet4 overload
ip nat inside source list 2 interface FastEthernet4 overload
access-list 1 remark SDM_ACL Category=2
access-list 1 permit 10.25.50.0 0.0.0.255
access-list 2 remark SDM_ACL Category=2
access-list 2 permit 10.25.55.0 0.0.0.255
control-plane
bridge 1 protocol ieee
bridge 1 route ip
line con 0
exec-timeout 30 0
password Cisco
logging synchronous
no modem enable
line aux 0
line vty 0 4
exec-timeout 20 0
password Cisco
logging synchronous
scheduler max-task-time 5000
end
mr-r1#
Similar Messages
-
Help converting Cisco 871W Wireless configuration to Cisco 881W
I am in the process of trying to convert my Wireless setings over from our existing 871W to the new 881W routers. I have found some documentation http://www.cisco.com/en/US/solutions/collateral/ns340/ns517/ns430/ns855/white_paper_c11-492842.html but after reading it seems a) a bit confusing and b) doesn't cover how to handle multiple SSID's on different VLAN's.
My existing 871 configuration looks like this:
interface Dot11Radio0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
no ip route-cache cef
no ip route-cache
encryption vlan 1 mode ciphers aes-ccm
encryption vlan 3 mode ciphers aes-ccm
broadcast-key vlan 1 change 3600
ssid <Home SSID>
ssid <Corporate SSID>
mbssid
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
packet retries 32
station-role root
rts threshold 2312
rts retries 50
dot1x reauth-period 3600
no cdp enable
interface Dot11Radio0.1
description Corporate Data and Voice
encapsulation dot1Q 1 native
no ip route-cache
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.2
description Untrusted Home
encapsulation dot1Q 3
no ip route-cache
no cdp enable
bridge-group 3
bridge-group 3 subscriber-loop-control
bridge-group 3 spanning-disabled
bridge-group 3 block-unknown-source
no bridge-group 3 source-learning
no bridge-group 3 unicast-flooding
interface BVI1
description Bridge Interface - Corporate Data
ip address x.x.x.x x.x.x.x
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
zone-member security in-zone
no ip route-cache cef
no ip route-cache
ip tcp adjust-mss 1260
service-policy input QOS_POL_REMARK_CORPORATE
interface BVI3
description Bridge Interface - Home
ip address 192.168.x.x 255.255.x.x
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
zone-member security home-zone
no ip route-cache cef
no ip route-cache
ip tcp adjust-mss 1260
service-policy input QOS_POL_REMARK_HOME
Can anyone lend a hand on how my 881W configuration might look like? You can't create multiple bridge groups and route IP (you can only do that over bridge group 1). I need to make sure that I can have two logically separated wireless networks (one for corporate and one for home) and that they get the right IP addresses from their right VLAN's.
Any input would be greatly appreciated.
MattFound a solution:
dot11 ssid BLAH
no vlan 1
interface Dot11Radio0
encryption mode ciphers aes-ccm tkip
Boom!
ap#sh ip int brief dot0
Interface IP-Address OK? Method Status Protocol
Dot11Radio0 unassigned YES NVRAM up up -
Backing up and restoring wireless configurations
I am getting ready to blow away my iBook and do a fresh install of OS X. I use my iBook in a variety of different areas and have it setup on several WEP and WPA protected networks. Basically, I'd like to be able to backup my wireless configurations and restore them once I reinstall the OS.
I would assume it's the com.apple.airport.plist in you user Library>Preferences folder (network locations/preferences are user specific). Drag it to the desktop and restart Airport. Are your various locations there? No? Then that's it.
John -
Wireless configuration for HP OfficeJet 6500A plus All-In-One printer on Ubuntu 10.04
I have bought a HP OfficeJet 6500A plus All-In-One printer CN557A, which I want to use with ubuntu 10.04 64-bit as a wireless network printer.
Before i bought i checked compatibility on www.hplipopensource.org and www.openprinting.org, and all was in order.
The machine is autodetected and fully functional when connected with a usb cable, but i have not managed to get it to work as a wireless printer.
This is what I did:
I configured the printer on the wireless network (through the printer interface), and it connects. It prints out a "Wireless Network Test Report", and everything works. I can ping to its local ip adress, and access it through the browser. HP eprint also works.
I installed hplip 3.11.10 and dependencies manually. I did this because the default hplip in ubuntu 10.04 did not recognise the device.
I ran 'hp-check', which gave no errors or warnings:
tjoff@mek-403-jakbo-01:~$ hp-check
HP Linux Imaging and Printing System (ver. 3.11.10)
Dependency/Version Check Utility ver. 14.3
Copyright (c) 2001-9 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
Note: hp-check can be run in three modes:
1. Compile-time check mode (-c or --compile): Use this mode before compiling the
HPLIP supplied tarball (.tar.gz or .run) to determine if the proper dependencies
are installed to successfully compile HPLIP.
2. Run-time check mode (-r or --run): Use this mode to determine if a distro
supplied package (.deb, .rpm, etc) or an already built HPLIP supplied tarball
has the proper dependencies installed to successfully run.
3. Both compile- and run-time check mode (-b or --both) (Default): This mode
will check both of the above cases (both compile- and run-time dependencies).
Saving output in log file: hp-check.log
Initializing. Please wait...
| SYSTEM INFO |
Basic system information:
Linux mek-403-jakbo-01 2.6.32-35-generic #78-Ubuntu SMP Tue Oct 11 16:11:24 UTC 2011 x86_64 GNU/Linux
Distribution:
ubuntu 10.04
Checking Python version...
OK, version 2.6.5 installed
Checking PyQt 4.x version...
OK, version 4.7.2 installed.
Checking for CUPS...
Status: scheduler is running
Version: 1.4.3
error_log is set to level: warn
Checking for dbus/python-dbus...
dbus daemon is running.
python-dbus version: 0.83.0
| COMPILE AND RUNTIME DEPENDENCIES |
note: To check for compile-time only dependencies, re-run hp-check with the -c parameter (ie, hp-check -c).
note: To check for run-time only dependencies, re-run hp-check with the -r parameter (ie, hp-check -r).
Checking for dependency: CUPS - Common Unix Printing System...
OK, found.
Checking for dependency: CUPS devel- Common Unix Printing System development files...
OK, found.
Checking for dependency: CUPS image - CUPS image development files...
OK, found.
Checking for dependency: DBus - Message bus system...
OK, found.
Checking for dependency: gcc - GNU Project C and C++ Compiler...
OK, found.
Checking for dependency: GhostScript - PostScript and PDF language interpreter and previewer...
OK, found.
Checking for dependency: libcrypto - OpenSSL cryptographic library...
OK, found.
Checking for dependency: libjpeg - JPEG library...
OK, found.
Checking for dependency: libnetsnmp-devel - SNMP networking library development files...
OK, found.
Checking for dependency: libpthread - POSIX threads library...
OK, found.
Checking for dependency: libtool - Library building support services...
OK, found.
Checking for dependency: libusb - USB library...
OK, found.
Checking for dependency: make - GNU make utility to maintain groups of programs...
OK, found.
Checking for dependency: PIL - Python Imaging Library (required for commandline scanning with hp-scan)...
OK, found.
Checking for dependency: PolicyKit - Administrative policy framework...
OK, found.
Checking for dependency: PyQt 4 DBus - DBus Support for PyQt4...
OK, found.
Checking for dependency: Python DBus - Python bindings for DBus...
OK, found.
Checking for dependency: Python devel - Python development files...
OK, found.
Checking for dependency: Python libnotify - Python bindings for the libnotify Desktop notifications...
OK, found.
Checking for dependency: Python XML libraries...
OK, found.
Checking for dependency: Python 2.3 or greater - Required for fax functionality...
OK, found.
Checking for dependency: Python 2.2 or greater - Python programming language...
OK, found.
Checking for dependency: Reportlab - PDF library for Python...
OK, found.
Checking for dependency: SANE - Scanning library...
OK, found.
Checking for dependency: SANE - Scanning library development files...
OK, found.
Checking for dependency: scanimage - Shell scanning program...
OK, found.
Checking for dependency: xsane - Graphical scanner frontend for SANE...
OK, found.
| HPLIP INSTALLATION |
Currently installed HPLIP version...
HPLIP 3.11.10 currently installed in '/usr/share/hplip'.
Current contents of '/etc/hp/hplip.conf' file:
# hplip.conf. Generated from hplip.conf.in by configure.
[hplip]
version=3.11.10
[dirs]
home=/usr/share/hplip
run=/var/run
ppd=/usr/share/ppd/HP
ppdbase=/usr/share/ppd
doc=/usr/share/doc/hplip-3.11.10
icon=/usr/share/applications
cupsbackend=/usr/lib/cups/backend
cupsfilter=/usr/lib/cups/filter
drv=/usr/share/cups/drv/hp
# Following values are determined at configure time and cannot be changed.
[configure]
network-build=yes
pp-build=no
gui-build=yes
scanner-build=yes
fax-build=yes
dbus-build=yes
cups11-build=no
doc-build=yes
shadow-build=no
hpijs-install=no
foomatic-drv-install=no
foomatic-ppd-install=no
foomatic-rip-hplip-install=no
hpcups-install=yes
cups-drv-install=yes
cups-ppd-install=no
internal-tag=3.11.10
restricted-build=no
ui-toolkit=qt4
qt3=no
qt4=yes
policy-kit=no
hpijs-only-build=no
lite-build=no
udev-acl-rules=yes
hpcups-only-build=no
hpijs-only-build=no
Current contents of '/var/lib/hp/hplip.state' file:
# hplip.state - HPLIP runtime persistent variables.
[plugin]
installed=0
eula=0
Current contents of '~/.hplip/hplip.conf' file:
[last_used]
printer_name =
working_dir = .
device_uri = "hp:/usb/Officejet_6500_E710n-z?serial=CN16F2402Q05JW"
[commands]
scan = /usr/bin/xsane -V %SANE_URI%
[installation]
version = 3.11.10
date_time = 2011-11-16 14:30:35
[settings]
systray_messages = 0
systray_visible = 0
[fax]
email_address =
voice_phone =
[refresh]
rate = 30
enable = false
type = 1
[polling]
enable = false
device_list =
interval = 5
| DISCOVERED USB DEVICES |
Device URI Model
hp:/usb/Officejet_6500_E710n-z?s HP Officejet 6500 E710n-z
erial=CN16F2402Q05JW
| INSTALLED CUPS PRINTER QUEUES |
B-403-271-A4-COLOR2
Type: Unknown
Device URI: smb://mek-ps1.win.dtu.dk/403-271-A4-Color
B403-271-A4-BW
Type: Unknown
Device URI: smb://mek-ps1.win.dtu.dk/403-271-A4-BW
HP-Officejet-6500-E710n-z-FAX
Type: Printer
Device URI: hp:/usb/Officejet_6500_E710n-z?serial=CN16F2402Q05JW
PPD: /etc/cups/ppd/HP-Officejet-6500-E710n-z-FAX.ppd
PPD Description: HP Officejet 6500 e710n-z, hpcups 3.11.10
Printer status: printer HP-Officejet-6500-E710n-z-FAX is idle. enabled since 2011-11-16T01:00:45 CET
Communication status: Good
| SANE CONFIGURATION |
'hpaio' in '/etc/sane.d/dll.conf'...
OK, found. SANE backend 'hpaio' is properly set up.
Checking output of 'scanimage -L'...
device `hpaio:/usb/Officejet_6500_E710n-z?serial=CN16F2402Q05JW' is a Hewlett-Packard Officejet_6500_E710n-z all-in-one
| PYTHON EXTENSIONS |
Checking 'cupsext' CUPS extension...
OK, found.
Checking 'pcardext' Photocard extension...
OK, found.
Checking 'hpmudext' I/O extension...
OK, found.
Checking 'scanext' SANE scanning extension...
OK, found.
| USB I/O SETUP |
Checking for permissions of USB attached printers...
HP Device 0x5412 at 002:005:
Device URI: hp:/usb/Officejet_6500_E710n-z?serial=CN16F2402Q05JW
Device node: /dev/bus/usb/002/005
Mode: 0664
| USER GROUPS |
lp adm dialout cdrom plugdev lpadmin admin sambashare vboxusers
| SUMMARY |
No errors or warnings.
Done.
I then ran 'sudo hp-setup', chose the device (which was detected), chose my wireless network, entered the wireless security key. On the configuration results dialog I get two messages:
"Your printer has been succesfully configured on the wireless network. You may now unplug the USB cable"
and
"The Ethernet cable is plugged in which will prevent you from connecting to a wireless network. To connect wirelessly, remove the cable and try again. (VSA000)"
There is no ethernet cable plugged in, so i can't remove it. I unplug the USB cable and click 'finish'. This makes the 'hp-setup'-dialog start over again, and the printer has not been installed.
In the terminal i have the following:
tjoff@mek-403-jakbo-01:~$ sudo hp-setup
[sudo] password for tjoff:
HP Linux Imaging and Printing System (ver. 3.11.10)
Printer/Fax Setup Utility ver. 9.0
Copyright (c) 2001-9 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
Searching on USB bus...
GET /IoMgmt/Adapters HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
GET /IoMgmt/Adapters/Wifi0/WifiNetworks HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
GET /IoMgmt/Adapters/Wifi0/Profiles/Active HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
GET /IoMgmt/Adapters/Wifi0/Protocols HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
error: Missing response key: 'iorotocols-iorotocol-dd:dnsserveripaddress-0'
GET /IoMgmt/Adapters/Wifi0/VsaCodes.xml HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
GET /IoMgmt/Adapters/Wifi0/WifiNetworks/SSID=mVnmXfsu HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
GET /IoMgmt/IoConfig.xml HTTP/1.1
Host: localhost
User-Agent: hplip/3.0
Content-Type: text/xml; charset=utf-8
Content-Length: 0
I then tried to reconnect the printer usb cable and run 'hp-toolbox' and click "Wireless/wifi setup using USB". Now i get the error:
tjoff@mek-403-jakbo-01:~$ hp-toolbox
HP Linux Imaging and Printing System (ver. 3.11.10)
HP Device Manager ver. 15.0
Copyright (c) 2001-9 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
HP Linux Imaging and Printing System (ver. 3.11.10)
Wifi Configuration Utility ver. 1.1
Copyright (c) 2001-9 Hewlett-Packard Development Company, LP
This software comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to distribute it
under certain conditions. See COPYING file for more details.
error: Channel write error
error: An I/O error occurred. Please check the USB connection to your printer and try again. (Device I/O error)
Done.
I do not how get past this stage, and any help is welcome.
This question was solved.
View Solution.A friendly soul on ubuntuforums pointed out to me, that the wireless configuration is only necessary when the printer is NOT connected to a (W)LAN. So all I really had to do was to configure the printer in the CUPS administation page, and it worked. Problem solved. Silly me.
-
Renewing wireless configuration
Told by Linksys support I needed to contact my hardware supplier to sort out "renewing my wireless configuration". I see on a internet search that this is a ball of blame that bounces between the wireless people an Microsoft with us users in the middle. Anyone know how to do this?. have wrt54g router and a musb54gsc network adaptor that refuses to recognize the signal at wireless computer. went through all the normal resetting procedures with phone support before they copped out.
ThanksI think you can verify if its computer by bringing some laptop and trying to connect to your wireless network, if that connects, router is working fine. Adapter or computer is having issue.
You can try to update the drivers of adapter, and see if that helps.
Just latest download drivers from www.linksys.com/download for correct model and version number.
Uninstall old drivers, restart the computer, and install new drivers. And then try to connect to your wireless network. -
B110 wireless configuration lost every printer turn off
Every time I turn off the printer, the printer lost the wireless configuration, so I have to reconfigure the wireless network access every turn on, is there a way to save the setup?
This question was solved.
View Solution.I believe this is a bug in the firmware. Make sure your firmware is up to date (Setup > Preferences > Update Product) and wait for a fix.
Until then, just leave the thing on. It goes to sleep and uses very little power (almost the same as when it is turned off).
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP -
Hi Guys, I have a question about wireless configuration files. I have set my wireless up and I am able to get it working. To do this I have to enter the iwconfig command manually.
iwconfig eth2 essid GillisLAN
When I do that and restart the network it works fine. I have read the forum and wiki and have tried many of the suggestions I have found in them. I must be missing something because I cannot get any of the config files to set things up for me. I have posted my the network portion of rc.conf below. I would really like to solve this and need some help.
David
# NETWORKING
HOSTNAME="DsLNVO"
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# Note: to use DHCP, set your interface to be "dhcp" (eth0="dhcp")
lo="lo 127.0.0.1"
###eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
###eth0="dhcp"
eth2="dhcp"
###wlan_eth2="wlan0 essid GillisLAN"
##WLAN_INTERFACES=(wlan0)
INTERFACES=(lo eth2)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.7.1"
ROUTES=(!gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network-profiles
#NET_PROFILES=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng ipw3945d network netfs portmap fam dbus hal crond kdm)As far as I know, wpa_supplicant can be setup without encryption.
Here is the Arch wiki page on setting up wpa_supplicant-
http://wiki.archlinux.org/index.php/Wpa_supplicant
Also take a look here at the WPA supplicant section in the gentoo handbook. It includes helpful examples of different configurations which the Arch documentation doesn't.
http://www.gentoo.org/doc/en/handbook/h … art4_chap4 -
I want to setup two wireless configurations.
1. DHCP
2. Static
At work I have to wireless access points one is DHCP and static. I have tried setting up two different configurations, but they seem to conflict with each other at work/home. Users report that they cannot connect to those two automatically. I then have to make one of them inactive I usually do that to the static because the employees can take home the MacBook Pros/Airs. I also make one inactive because, they reported having trouble connecting at home. Is there a way for both of them to exist "both active"? I cannot give the users admin right,so they cannot change the network settings.You've done quite a bit of troubleshooting and I don't have much to add, but I wonder what you intend to accomplish with the settings I've highlighted:
*Enabled default host* at: 192.168.1.253
*Enabled NAT Port Mapping Protocol*
iMac:
Configure IPv4: Using DHCP *with manual address*
IP Address: 192.168.1.253
Try un-checking that "enable default host", and don't specify a manual IP address for your iMac unless you have a good reason.
I would suggest you configure the iMac the same way as your MBP:
MacBook Pros:
Configure IPv4: Using DHCP -
Claer Wireless configuration - Laserjet CP1525nw
I had to replace a router in a home of a neighbor, they previously had the subject printer connected wirelessly. The new router forced me to change the passphrase for the wireless connection from what was previously used. The same SSID IS being used on the new router. I have tried all attempts to reset the network settings on the printer and whenever I do and then repeat the wireless setup, be it by WPS, PIN or CD-ROM and USB cable, in ALL cases the connection fails and in best cases says security passphrase is wrong or in worst cases that the printer does NOT see the CORRECT wireless network. The oddest part, apart from the total lack of a solution on the HP forums, or even in the manuals, is that the printer keeps picking up an odd-ball SSID, "HPCP1525-135f8d", mode is ad-hoc and the IP comes up with a "bogus" number which does NOT match any local network, 169.254.123.35. I have seen IP's like this before on PC NIC adapters which cannot connect, I believe this is some kind of internally assigned IP, not from any networking device. That combined with the bogus SSID, I am confident the printer is the source of this BAD configuration data. I have even tried to manually set the IP, using a reserved IP on the router which I set up just for this printer. Still nothing, it fails to connect and collects and saves this bad SSID and IP. How the h*ll do you get the NVRAM of the printer to drop this IP and FORGET that SSID? Do NOT tell me to re-run setup, I have tried multiple times, that may temporarily clear the data, but in re-running the setup it to again collects and SAVES the bad configuration data. My best guess, and another solution which cannot be found ANYWHERE, is how do you do a HARD factory reset on the printer??? I have just about had my fill of the user-friendliness of these HP interface and setup software!!!!! HELP!!!!
I found this on an earlier post and it works for the person. You have to first connect the printer with a ethernet cable to your network router as there should be ports available and then follow the instructions below: The No-Bull**bleep** Way To Setup Your HP CP1525nw For Wireless Printing Connect the printer to your router via ethernet cable.At this point you might need to navigate via the LCD and printer buttons to the Network setup. It’s a simple menu tree that you navigate via clicking the arrow buttons and clicking OK. Just connect via Ethernet and use DHCP. It should connect itself to your network.Once the printer connects to your network it will display its IP address on the printer’s built-in LCD screen.Enter that IP address into a web browser on a computer that is on the same network. After you click enter you will be presented with a web-based administration interface for your printer.Click on the “Networking” tab.Click on “Wireless Configuration” on the left-hand options.Status should be “ON”
Configuration Method should be “Join an existing network”.
Network Name should present a list of available networks. Click on yours.
Authentication should be set according to your networkClick APPLY and disconnect the wired connection to the router. The little wireless light on the front of the printer will start blinking as it connects to your router wirelessly. Once the light is solid the printer’s new IP address should be displayed on the built-in LCD display. You should now be able to connect using that ip address. -
I was told my wireless configuration was not correct and it is making my router slow. It is not giving me my true internet speed. I am suppose to be getting 50 mbs and I am only getting around 5 mbs. Can anyone give me some help in improving my wireless configuration. When I connect a cat 5 cable to the router it works just great, only when it is wireless does it slow down. Any help for this veteran would be appreciated.
Thanks
RandyIt's not recommended to speed test over wireless due to many variables that may cause inaccurate results.
Single mode N or Mixed mode for testing on both radios.
Channel Width set for Auto 20/40Mhz.
Try setting a manual Channel to a open or unused channel. 1, 6 or 11. 11 for single mode N if the channel is clear. 13 for EU regions. Try channel 48 or 149 on 5Ghz. http://en.wikipedia.org/wiki/List_of_WLAN_channels
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=f2625b15a5d7454b8e7fafbe65d5aa63_4009.xml&pid=80&r...
What security mode are you using? Preferred security is WPA-Personal. WPA2 Only. http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=8ce9e83bd3784001aee72da7f1ef48e8_Changing_the_basi...
http://kb.linksys.com/Linksys/ukp.aspx?pid=80&vw=1&articleid=19073
What wireless devices do you have connected?
Ensure any devices with WiFi adapter drivers are updated.
Any 2.4Ghz or 5Ghz cordless house phones or WiFi APs near by?
Any other WiFi routers in the area? Link> Use http://www.techspot.com/downloads/5936-inssider.html to find out. Use v3. How many?
WMM Support must be enabled for single wireless N mode to function.
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&articleid=5471
Router Placement
Forum User - "Well I feel really dumb. After moving the router away from other electronic devices my speeds are back to normal. Just a heads up for anyone experiencing slow speeds, you might want to move it away from other electronics and see if that helps."
3-6' feet minimum safe distance between devices.
Placement on main level floor and central in the building and WELL ventilated is preferred. Not in basements or closets as building materials, or near by electronics devices could interfere or hinder good signal propagation.
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=d9a3b1b2039741948a2365b053a93ea8_3759.xml&pid=80&r...
http://www.smallnetbuilder.com/wireless/wireless-basics/31083-smallnetbuilders-wireless-faq-the-esse... -
E2500 constant connectivity failures when secure wireless configured
My E2500 constantly drops connectivity (wired and wireless) when secure wireless is configured through the Linksys Connect software. The problem doesn't happen if the router is left unsecured.
Router Firmware: 3.0.00 build 6.
ISP: Comcast cable
Cable modem model UBEE D3.0
I use a mix of wired and wireless - the PCs are wired and the tablets and phones use wireless connections. The laptop uses wired at the desk and wireless elsewhere.
When I first got the router and used Linksys Connect to configure, the connection was moderately stable for about a week, then started dropping frequently. Recycling the modem and resetting the router to factory defaults stabilized the connection.
Today I re-ran the Linksys Connect software to configure secure wireless for my wireless devices, and the intermittent connectivity problem came back immediately - I couldn't get more than a minute or two online without the connection dropping out.
I don't like running without secured wireless connection, but I don't see an alternative.Wireless Configurations
What wireless modes are you using?
2.4Ghz and 5Ghz routers: Try single mode G or N or mixed G and N on 2.4Ghz and single mode N or Mixed on 5Ghz?
Channel Width set for Auto 20/40Mhz or try 20Mhz only.
Try setting a manual Channel to a open or unused channel. 1, 6 or 11. 11 for single mode N if the channel is clear. 13 for EU regions. Try channel 48 or 149 on 5Ghz. http://en.wikipedia.org/wiki/List_of_WLAN_channels
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=f2625b15a5d7454b8e7fafbe65d5aa63_4009.xml&pid=80&r...
What security mode are you using? Preferred security is WPA-Personal. WPA2 Only. http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=8ce9e83bd3784001aee72da7f1ef48e8_Changing_the_basi...
http://kb.linksys.com/Linksys/ukp.aspx?pid=80&vw=1&articleid=19073
What wireless devices do you have connected?
Ensure any devices with WiFi adapter drivers are updated.
Any 2.4Ghz or 5Ghz cordless house phones or WiFi APs near by?
Any other WiFi routers in the area? Link> Use http://www.techspot.com/downloads/5936-inssider.html to find out. Use v3. How many?
WMM Support must be enabled for single wireless N mode to function.
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&articleid=5471
Router Placement
Forum User - "Well I feel really dumb. After moving the router away from other electronic devices my speeds are back to normal. Just a heads up for anyone experiencing slow speeds, you might want to move it away from other electronics and see if that helps."
3-6' feet minimum safe distance between devices.
Placement on main level floor and central in the building and WELL ventilated is preferred. Not in basements or closets as building materials, or near by electronics devices could interfere or hinder good signal propagation.
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=d9a3b1b2039741948a2365b053a93ea8_3759.xml&pid=80&r...
http://www.smallnetbuilder.com/wireless/wireless-basics/31083-smallnetbuilders-wireless-faq-the-esse... -
Cisco 871W Wireless Performance
I have a newly configured 871W router that is giving me terrible performance via wifi. Via ethernet I am getting normal 100Mbit speeds. The router is configured for 54Mbit/sec, my computer thinks it is connected at 54Mbit/sec (see attached photo).
iperf client & server output:
client:~ jsimon$ iperf -c 10.0.20.100
Client connecting to 10.0.20.100, TCP port 5001
TCP window size: 129 KByte (default)
[ 4] local 10.0.30.207 port 55307 connected with 10.0.20.100 port 5001
[ ID] Interval Transfer Bandwidth
[ 4] 0.0-10.0 sec 20.5 MBytes 17.2 Mbits/sec
jsimon@server:~$ iperf --server
Server listening on TCP port 5001
TCP window size: 85.3 KByte (default)
[ 4] local 10.0.20.100 port 5001 connected with 10.0.30.207 port 55307
[ ID] Interval Transfer Bandwidth
[ 4] 0.0-10.3 sec 20.5 MBytes 16.8 Mbits/sec
See my running config:
wifi871a#show run
Building configuration...
Current configuration : 5145 bytes
version 12.4
service nagle
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname wifi871a
boot-start-marker
boot-end-marker
logging message-counter syslog
logging buffered 51200 warnings
enable secret 5 $1$NJNA$p4/81Kkji2yMuC8UE21td1
no aaa new-model
crypto pki trustpoint TP-self-signed-2242084313
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-2242084313
revocation-check none
rsakeypair TP-self-signed-2242084313
crypto pki trustpoint TP-self-signed-2631278149
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-2631278149
revocation-check none
rsakeypair TP-self-signed-2631278149
crypto pki certificate chain TP-self-signed-2631278149
dot11 syslog
dot11 ssid 10fir
vlan 30
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 xxxxxxxxxxxxxx
ip source-route
ip dhcp excluded-address 10.10.10.1
ip dhcp excluded-address 10.0.30.1 10.0.30.199
ip dhcp pool sdm-pool
import all
network 10.10.10.0 255.255.255.248
default-router 10.10.10.1
lease 0 2
ip dhcp pool Users
import all
network 10.0.30.0 255.255.255.0
default-router 10.0.30.1
domain-name 10fir.com
dns-server 4.2.2.2
lease 0 3
ip cef
ip domain name 10fir.com
ip name-server 8.8.8.8
ip name-server 4.2.2.2
no ipv6 cef
multilink bundle-name authenticated
archive
log config
hidekeys
bridge irb
interface FastEthernet0
switchport access vlan 30
spanning-tree portfast
interface FastEthernet1
switchport access vlan 30
interface FastEthernet2
switchport access vlan 30
spanning-tree portfast
Interface FastEthernet3
switchport access vlan 30
spanning-tree portfast
interface FastEthernet4
ip address 10.0.20.20 255.255.255.0
duplex auto
speed auto
interface Dot11Radio0
no ip address
no dot11 extension aironet
encryption mode ciphers aes-ccm
encryption vlan 30 mode ciphers aes-ccm
broadcast-key change 3600
ssid SSID
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root access-point
no cdp enable
interface Dot11Radio0.30
encapsulation dot1Q 30
no cdp enable
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 spanning-disabled
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$
no ip address
ip tcp adjust-mss 1452
shutdown
interface Vlan30
description Users Network
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat inside
ip virtual-reassembly
bridge-group 30
bridge-group 30 spanning-disabled
interface BVI30
description Wifi Bridge
ip address 10.0.30.1 255.255.255.0
ip virtual-reassembly
router eigrp 10
network 10.0.0.0
no auto-summary
ip default-gateway 10.0.20.1
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 10.0.20.1
no ip http server
ip http authentication local
no ip http secure-server
ip http timeout-policy idle 5 life 86400 requests 10000
ip dns server
control-plane
bridge 30 route ip
line con 0
privilege level 15
login local
no modem enable
line aux 0
line vty 0 4
privilege level 15
login local
transport input telnet ssh
scheduler max-task-time 5000
endAlso if I setup another router on the same frequencies I get perfect performance.
Another 871W or something else.
If it's another router model, I think you need to look at this. I have a strange feeling you're hitting the limit of the hardware. Not the wireless capabilities, but the router itself. -
Wireless Configuration: HP Photosmart Premium C309g-m
I had no difficulty in configuring 27" iMac to communicate wirelessly with HP C309g-m.
Doing the same for Macbook Air has me stymied.
The set up has me go to this page:
http://hpf5e3a5.local./index.htm?cat=network&page=device
Selecting (left sidebar) "Wireless (802.11)", the set up wizard is opened.
http://hpf5e3a5.local./wlSetup.htm
After entering Network Name and WPA password, I click on "finish" and the progress bar proceeds half way... *and no further!*
Am I doing something incorrectly?Well you can try deleting all the print jobs, then uninstalling the printer from the MBA, restarting the MBA using a SMC reset and then reinstalling the printer in the Print & Fax utility. If that doesn't work you have 3 months of AppleCare, I'd recommend calling them for some help. If you need help on doing a SMC reset the instructions are:
*SMC RESET*
• Shut down the computer.
• Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
• On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
• Release all the keys and the power button at the same time.
• Press the power button to turn on the computer. -
Trying to understand traffic Flow in a LWAPP wireless configuration.
I'm trying to understand at a high level how wireless traffic flow in the new LWAPP configuration. Based on what I can tell all wireless traffic must flow through the controllers prior to getting onto the LAN.
So lets say I have a LWAPP Access Point off an access switch in a remote closet and my controller is off my core switches. I want to communicate from my wireless PC to a wired PC on this same access switch. The traffic flows from the AP down to the core switch, through the Controller and back up to the access switch to the wired PC.
Is that correct?
If this is true my main concern is supporting APs from a central controller across a low speed WAN. Looks like I would not want to do that...You're right in your assumption. Data traffic travels from the client to the AP. The AP then encapsulates this data using LWAPP and forwards it to the Controller. The WLC then de-encapsulates (?) it, processes the traffic as necessary and then drops it onto the wired LAN.
So, in your scenario, the wireless client would send data to the AP. This would be encapsulated between the AP and the controller and then sent back again unencapsulated to the wired client.
Regarding using this system over a low speed WAN, there are two ways of doing this.
The first is to use a local WLC at the remote site (e.g. a WLC2006 or the new WLC network module for 2800/3800 ISR routers).
The second is to use AP1030s which are 'Remote Edge Access Points'. These aren't quite as lightweight as the rest of the 1000 Series in that they will bridge local traffic and only encapsulate traffic heading 'off site'. They will also continue to operate if connection back to the WLC is lost (the first WLAN configured on the WLC remains up on the REAP whilst connection to the WLC is lost).
I believe that the recommendation for these is a minimum of 2Mbps WAN connection. -
857 Wireless configuration help
Can someone help me with a wireless setup of an 857. I have done this in the past but can't remember the details. Basically I want very simple setup with WPA-PSK. The SDM interface is very confusing and I could do with the basic CLI for this.
Thanksplease see this link for the 857 initial configuration:
http://www.cisco.com/en/US/products/hw/routers/ps380/products_installation_guide_chapter09186a0080471066.html
this is a step-by-step for SDM and CLI basic configuration.
Maybe you are looking for
-
https://support.mozilla.com/en-US/home Even the support page does not recognize the update... OR Pandora (no listening with Firefox now), Google, mozilla support, etc.. This has been an issue way too long what's up mozilla? Warning: Firefox 3.6 will
-
Hi, http://scrimshawcomm.info/test_menu.html I am trying to create a horizontal menu. It works fine in Firefox and was working in IE. When I took the width value out of the #menuh ul I lost the inline effect on IE. It still works in Firefox etc. If I
-
I'm not a Aperture user, I'm just trying to figure out which program to use. I tried iPhoto, I've used iView for several years (but don't really like it), I looked at Adobes program, and now I'm playing with Aperture. There is however one thing I hav
-
hi OSB has by default provided validate action. It has syntax as "validate <xpath> in {variable} against {schema/wsdl}". Can i decide at schema/wsdl at run time? This scenario is similar with that of using a dynamic xquery. Regards, Swapnil Kharwadka
-
Can access network/inet but cannot get out to "browse"
Greetings almighty MAC gurus! I have seen the light and thrown off the PC shackles. But alas, they chains are long! I am configured thru a linkys wireless router (attached to a pc homen network). I get an inet connect, IP addy etc. But when opening s