875p neo doesn't always boot

More often than not if I shut down the pc it will not always turn back on. (it will "click" like it wants to boot but doesn't do anything more than than.. like the power came on for a split second) If I leave the power off a while it usually will boot. Sometimes I have to clear CMOS to get it to boot.
Then sometimes if I shut it down it will immediately reboot instead. Similarly sometimes when I connect power it will boot without me pressing the on switch. And then sometimes it will "click" repeatedly when I connect the power.
Once it's running everything is fine.
Anyone have any ideas what can cause this?
fk

Faithkills
Id deffinately say PSU problem i have an almost exact match to your system, mine is 100% stable (I dont use CoreCenter, Motherboard Monitor and MSI's WMI program give me random reboots) ...i did have to increase my DDR voltage to 2.7v -after flashing to the 1.4 BIOS
P4 3.0G 800 FSB
Antec Truepower 330W PSU
2 * corsair pc3200 256mb ddr
875p NEO-LSR
Geforce3 64 (i also use the ASUS 8200)
witchywoman it depends on the max power for each voltage line -not all PSU's give the same even if their rating is equal or above
http://www6.tomshardware.com/howto/20030609/index.html
I would recomend atleast 450W for a new PSU (to give upgrade potential)

Similar Messages

875P NEO FIS2R problems with booting at power-up

Having problems with booting at power-up.
Recently, with no apparent modification to system - at power up the system will often not boot. About 80% of time systems seems to go into a loop with CD/DVD drive light blinking a few times, then the floppy drive light comes on and can hear the FDD run – within 30 seconds or so, this process starts over again. Power switch LED is on and HDD LED is on (continuously). All fans are running (power supply fan, case fan, CPU fan and Intel Canterwood 875 fan ).
Monitor power on light is in power save mode (amber) when system does not boot. When boot is successful the monitor power light turns green immediately.
After pressing the reset button several times (varies between pressing reset button 1 time to 30 or more times) system will then boot OK or go into set up.
Once running there is no apparent problem.
This mainboard comes with D Bracket containing 2 USB 2.0 ports, and 4 diagnostics LEDs - when boot problem occurs the diagnostic LEDs, give a code that in the MSI mainboard manual states “Initializing Keyboard Controller” and diagnostic LEDs stays in this mode until via reset button provides a successful boot and start up.
Have reseated all connectors.
SYSTEM
Mainboard – MSI 875P Neo FIS2R (MSI 6758)
BIOS – AMI v1.8 (has not been updated)
CPU – Intel P4 2.6 GHz - system bus 800 MHz 512 KB L2 Cache
Memory – 1.5 gb (2 x 256 mb and 2 x 512mb)
Power Supply – Antec 380 watt
HDD – IED WD 160 GB and IED WD 40 GB
Video Card – ATI Radeon 9600 (128 RAM)
Operating System – MS Windows XP Pro (sp2)

Quote from: BOSSKILLER on 17-May-08, 03:34:12
Have you done >>Clear CMOS Guide<<?
Cleared CMOS - no change same problem. Also, re-seated all connectors at same time.
Quote from: Wonkanoby on 17-May-08, 09:06:54
have you just added the second wd drive
are they jumpered right
jumperless if alone on ide
jumpered master /slave if two on it
No, second 40GB HDD was installed months before this issue started and is jumpered as slave drive. Also, no other additional hardware installed for several months before issue.

[875P Neo Series] Won't boot, 4 burning LEDS

Hi,
My computer, based on neo fis2r 875 with a p4 2.8 ghz 800fsb proc, worked perfectly for 2 years.
Yesterday it didn't boot anymore.
- the d-bracket gives me 4 burning leds (this means system booting?).
- no lights on the mouse or keyboard are burning
- stripped components one after another, same error
- system doesn't give error beeps
- system doesn't give the single booting beep
- no shortcircuit
- every fan in the case is on as usual
Is the cpu or mainbaord dead now?
Any ideas?
Regards,
Michel

Quote from: Din on 04-August-05, 18:09:22
If your devices workin properly in other computer, change your mainboard. What PSU you have? it's have Overvoltage protection? If you dont close the PSU when u shut down your computer, the PSU is giving power in all devices and it's dangerous for your computer. I lost my screen like this, but not my computer cause im always close my PSU
im a smart girl
Hey Din,
The pc is equipped with an Antec Truepower 480W PSU.
Is there no chance the CPU is fried? Changing the mainboard is more work then changing the CPU .
Michel

875p Neo-FIS2R - won't boot from CD

I am assuming I had a hard drive failure, but not certain. This was and old (9 years) hard IDE hard drive. My PC would no longer boot, saying "Boot Failure." I was able to boot with the WinXP cd and it did not see the hard drive. When booting with the CD, it took a LONG time to move from the splash screen into the CD boot process.
I bought a new SATA hard drive hoping that would solve the problem but no success. I attached the new drive to SER1. I can see it in the BIOS along with the CD/DVD drive. Both are selected in the boot order, but it will not boot to the CD with WinXP on it. The CD was on IDE 2 master. I moved to IDE 1 master and it made no difference. I turned off the splash screen and it says it is attempting to boot from CD/DVD but then fails.
The CD/DVD drive was just replaced with a new unit in November 2010. The power supply was also replaced in November (430w).
Any ideas? Thanks!

I got it to work. I tried a new IDE cable and that didn't help. Neither did trying to load from a DVD.
Finally, I put an old (broken) IDE hard drive on IDE 2 (CD is no IDE 1, new SATA hard drive on IDE 3). When I turned it on, it was searching for the second IDE master for a while, so I had it abort. It then booted right up with the WinXP CD. The Windows CD then got stuck at one point trying to access the broked IDE drive (just kept making a clanking noise). So I removed the power from that drive and the Windows install proceeded, and now everything works fine. I reconnected the other SATA drives (four in total) now and removed the IDE 2 cable completely.
Any ideas why it worked this way? It seems and IDE hard drive had to be connected to get the CD/DVD to boot. I have not tried booting to the CD again, now that everything is working. I will try that just to see what happens.

875P Neo FIS2R DRAMM / Boot Problems

After having significant difficulties with my new machine
I thought it may be helpful to others to know how I fixed the Mother Board problems. I have the following configuration:
875P Neo-FISR
P4 3.02 GHz 478P 800fsb
Two Geil PC 3200 400MHz 500mb DDR’s at positions 1 & 3
( CAS 2 6-3-3 1T; 2.6-2.9 V)
Two Seagate 120 Gb 7200rpm SATA drives on Promise Raid 0
Generic Cd Reader
Pioneer DVD Writer DVRA05
ATI 9700 Pro
Aquarius Liquid Cooler
Enermax Fan Monitor
( Addictions are bad )
Open all the boxes and put everything together. Boots up once and then starts active unstable.
Clear the CMOS and then it fails to post at all.
No monitor at all.
Looking at this web site I thought that putting the Aquarius Fan on the SFAN 1 slot may not be playing with CoreCell Chip well. Switched to the Enermax and it boots. Remains very unstable. Reading an email here I changed the DDR voltage to 2.7. System stable but I can’t get the Promise RAID to engage.
Looked at another email ( Thanks Mr. K. Keenan)
and set the BIOS as follows:
Frequency / Voltage Control:
CPU Ratio Selection: Locked
Dram Frequency : AUTO
Spread Spectrum : DISABLED
Adj. CPU BUS Clock: 230
DDR Clock: 460
Adj. AGP/PCI Clock: 67.1/33.50
CPU Vcore Adjust: YES
CPU Vcore: 1.5750V
DDR Power Voltage: 2.70 ( KK suggested 2.65)
AGP Power Voltage : 1.75
Everything stabilized.
Start adjusting the Promise RAID settings (following M. Johnson’s advice)
as follows in the BIOS:
ON CHIP IDE Configuration
ON Chip ATA Operate Mode: Native Mode
ATA Configuration : S-ATA Only
P-ATA Keep Enabled : YES
P-ATA Channel Select : BOTH
S-ATA Ports Definition: PO-1st/P1-2nd
Configure S-ATA as Raid : YES
Back to
INTEGRATED PHERIPHERALS
ONBOARD Promise IDE: as RAID
Run Windows 2000 prof and it finds the array but can’t format ( ???)
Tried formating with Millenium Boot disk ( Bad move).
Windows ME won’t let Win 2000 boot.
Clear CMOS and then the system dies.
Spent days trying to get at least the monitor to fire with no luck.
Reread web site and picked up on the Low Latency Memory issues noted
in a note ( Thanks Mr. K. Keenan again). Put in some Kingston cas2.5
333 DDR’s at 1 & 3 positions.
Fires up immediately.
Windows 2000 boots and loads. Totally stable.
Never to be one that leaves well enough alone…
Set the BIOS under
ADVANCED CHIP FEATURES as follows:
Under dram Timing Setting:
Configure DRAM Timing by SPD : Disabled
Cas Latency: 2
RAS # Precharge 3
RAS # to CAS# Delay: 3
Precharge Delay: 6
Burst Length : 8
AGP Aperture Size: 128 MB
Shut down and replaced the 1GB ( 2 x 500) Geil DDR 400’s.
Rock stable and faster.
Evidently when you clear the CMOS, the board resets
the DDR Power Voltage to 2.50 which is too low for
some of the faster DDR SDRAM’s. Unless you put
slower chips in you can’t adjust the bios to a higher voltage.
I would love to know why MSI did that.
Hope this trail helps somebody else.
Best RBC

Quote
Originally posted by Undergrid
Quote
Evidently when you clear the CMOS, the board resets
the DDR Power Voltage to 2.50 which is too low for
some of the faster DDR SDRAM’s. Unless you put
slower chips in you can’t adjust the bios to a higher voltage.
I would love to know why MSI did that.
Simply, when you use the jumpers to reset the BIOS all the settings, including the voltages, get reset to the default. The default power setting for RAM is 2.5v, and I would assume that its difficult to find RAM that doesn't run at that voltage at least well enough to get into the BIOS. What use would the jumper reset be if it only selectivly reset settings?
Hi all,
The system will reset the performance to Slow and the DDR ram timing to default by just 4 unsuccessful boot up.
Meaning just press reset button for about 4 times and the system will boot with the default setting for the performance and RAM Timing.
So I do not need to do jumper reseting or open the CPU casing.
Cheers.

875P Neo FIS2R-Slow boot with Raid on Intel + Raid on Promise

Hello all.
Here is the configuration I'm trying to set up (and almost did)
SI 875P Neo FIS2R,MS-6758 BIOS v2.4
P4 2.6 GHz HT
500W 6fan total
2x1G Kit DDR 400
2x74 G WD Raptor Raid0 (Intel S1-2) Win XP inst
2x36 G WD Raptor Raid0 (Promise S3-4)
GeCube X1600Pro
DVD-RW (IDE 2 )
Win XP SP2 (All latest updates installed)
I followed the instructions as they are listed in the sticky (great job btw) and configured the 2 SATA 74G WD Raptor on Intel Raid controller(serial1&2) as Raid0 and install WindowsXP Prof sp 2 on it.
Then I configured the 2 SATA 36G WD Raptor on Promise controller(serial3&4) as Raid0 and added this Raid to the existing WindowsXP installation.
This set up is working very good once I'm logged into Windows with no problems at all.
The glitch is that I need 3 min waiting time till I see the windows loading logo.
I have all the latest drivers installed also IAA and INFs and my bios is as the default values except the changes mentioned in the sticky
Onboard Promise IDE - as Raid
ON-Chip IDE Configuration:
Native Mode
SATA Only
Keep SATA Active - Yes
Keep PATA Active - Yes
PATA Channel selection - Both
Configure SATA as Raid - Yes
I did the Win XP installation twice till now, taking care to install INFs and drivers in the right order but the result is the same...3-5 mins till I have a fully operational windows environment and after that all is running like a dream.
Now, I've searched in the forum and saw that many more people have the same problem but never read the solution to it, so if someone has ever found the way to solve this or has the same configuration please tell me how he did it. Even if someone knows that it can't be solved just drop me a line telling me so. Altough the system is running smoothly I find the 3 min waiting time unacceptable and frustrating. I've run out of ideas so please help me.
Thanks in advance

Hello Blazer and thank you for replying.
Answering one at a time...
are both raid arrays setup with the same stripe size?--> Yes Both arrays are configured at 16k stripes
do you see both the intel and the promise bios setup screens?-->Yes both screens (Intel(R) RAID... and Fast Built (tm) ...)appear almost instantly after MSI's logo screen showing my Raid arrays in Normal status. The delay starts after the Promise's screen till the Windows Loading logo screen.
how is the raid bootable drive identified in the boot from menu?-->
Boot Device Priority:
1st BBS-0 (Raid): Intel <name> (---> this is the OS drive on Intel controller)
2nd Disabled
3rd Disabled
Try other boot devices NO
I have also the option to select the the Drive on Promise which shows as BBS-1 (Raid) FT 378 Ary 1 but I have left it out cause it doesn't have the OS on it.
is the OS drive labeled as C: and seen as 200GB drive [as one] from the four drive array]--> No as it shouldn't cause these are two different Raid Arrays. The first Raid on Intel's controller with the 2x74G WD Disks indeed shows as one C: 137 G and has the OS on it. The second on Promise controller with 2x36G WD Disks also shows as one D: 70G.These are two separate Arrays with 2 disks each and they show as indented.
is network boot enabled causing a delayed boot?--> I don't quit understand what you mean. In case you mean what happens if I unplug the 2 disks from the promise controller then yes if I do that the system boots fast in the Windows even if I leave the Bios setting "configure promise as raid"!!!
My problem is similar with this post: https://forum-en.msi.com/index.php?topic=69994.0
other posts that have reported the same trouble:
https://forum-en.msi.com/index.php?topic=94944.msg683258#msg683258
https://forum-en.msi.com/index.php?topic=81901.0
https://forum-en.msi.com/index.php?topic=66662.0
https://forum-en.msi.com/index.php?topic=98005.0 ---> I wish it was that simple, I did it as with all other drivers
I hope that info helps you helping me.

MSI 875P Neo-FIS2R support booting from USB devices?

I am building a super computer using the MSI 875P Neo-FIS2R. I would like to either get a USB pen drive, or an external Floppy Disk Drive in place of an internal Floppy Disk Drive.
Does anyone know if this board supports booting from a USB device?

I ordered my board as well, however, they were out of stock and it may be as long as 2 weeks before they get more in. If you don't mind me asking, where did you get yours from? I am VERY much excited about getting this board as I only await the MB and CPU. What all are you putting in yours??
Mine:
MB- Obvious
CPU- 2.4 800Mhz
RAM- 2 sticks, 256 PC 3200 XMS Corsair using dual channel, at first I think I will use the 512 pc3200 I already have though.
HDD- 80GIG W/D 7200 RPM ( May get another to run RAID 0)
VGU- Chaintech TI4200 at 8x w/ 128 DDR
CD#1- 52x cd rom
CD#2- dvd 16x, cdr 48 cdrw24 cdrom 48
500W raidmax Pwr Sup
Koolcases Panther case w/ window and 3 80MM/ 1 60MM fans
For now I will even use the old 3.5 A drive. Just in case.
Red light internaly
Digidoc 5 for thermal monitoring on:
1.cpu 2.ram 3.VGU 4.case 5.HDD 6.other ram 7.chipset 8.dvd for curiousity sake. just curious of the temps they produce. but always able to move it to a more vital area if the need arises.
Will be upgrading to liquid cooling in the future, that way when I am deployed the temps stay in the blue. (HOPEFULLY)

875P Neo/Boot from Serial ATA Raptor?

Hi all,
I am building a new system with a 875P Neo-LSR motherboard and Serial ATA Raptor drive that I want to install Windows XP on/boot from. I have it so Window's sees my Raptor drive but it won't let me format the drive. Any ideas???
The manual tells me to refer to "Serial ATA/Serial ATA Raid Manual"...well I haven't been able to find that...
I setup via a message I saw from JC74:
- operate mode should be Native
- ATA configuration S-ATA only
- keep P-ATA enabled Yes
- P-ATA channel select both
- S-ATA ports definition (first option)
- Configute S-ATA as RAID no (JC74 recommended Yes but I'm not setting up RAID)
This setup lets Windows XP see the drive but not format it.
I also downloaded the Intel ICH5R drivers on this website and as I booted up XP I attempted to load those drivers and got:
"File iastor.sys caused unexpected error(512) at line 2108 in d:\xpclient\base\..."
I'm stuck at this point ?(
Hopefully someone can help...thanks,
Ken

I read a post by wonkanoby that said that for WD drives make them jumperless so I removed the jumper that was in the right most side (its OEM so no manual...).
He also said to set boot order to cdrom, raid so I did that as well.
I also disconnected my WD 200GD.
After making all these changes I am now able to format the drive. I'm not sure what fixed the problem.
Knock on wood...hopefully I can get everything else working

875P Neo-FIS2R boot problem

Hello,
Just built a new machine with the following parts. Sometimes it boots fine, but mostly when you turn it on nothing happens, no beeps, no visual, no nothing. Also, once in awhile it takes 15 - 20 seconds before it beeps and visuals come on screen. It's using bios version 1.2 with all default settings by shorting out jumpers. (It gives different voltage settings when reset by jumpers vrs utility.) Once it boots it runs fine, even though memory timings are 2-4-4-6 SPD instead of 2-2-2-6 SPD that my memory modules are suppose to be. However when I manually change to 2-2-2-6 the bios shows that but CPU-Z still shows 2-4-4-6, thats a different story though which a bios update would probally fix. Right now all I want is for it to boot consistently, every time. Ive tried a different power switch and a different power supply. Neither helped and this is driving me crazy, somebody please assist or post any information you might feel would help.
Intel Pentium 4 2.4CGHz Processor 800MHz FSB
MSI 875P Neo-FIS2R
Corsair 512MB PC-3200/400MHz DDR Ram (TWINX512-3200LL)
ASUS GeForce4 Ti4200 128MB 8X (V9280 TD)
Integrated six channel audio on motherboard
Western Digital 80GB 7,200RPM 8MB Cache (WD800JB)
LITE-ON 16x/48x DVD/CD-ROM Drive (XJ-HD165H)
LITE-ON 52x24x52 CD-RW Drive (LTR-52246S)
TEAC 3.5" Floppy Drive
Black Raidmax Case with 350W Power Supply (278WB)
CTX Executive 19" TrueFlat 1600x1200 (EX950F)
Windows XP Home Edition Full Install
Nice black and silver multimedia keyboard
Microsoft Wheel Mouse Optical
Intel 56K V.90/V.92 PCI Data, Fax, Speakerphone

Hey,
I have /had same problem with Neo 875 and corsair TWINX512-3200LL and bios V1.2 It has something to do with mem settings and/or Vdimm voltage. At this moment it boots fine but I can't explain way. It seems that this kind of memory is very sensitive for the Vdimm voltage. 2.5V is to low and some systems refuse to post. (see the bios 1.4 flash problems) Must user use 2.6v; 2.65v or 2.7v. Check out if you can find a stable setting. Bios v1.2 uses default SPD settings. you can't change them. Although after bios reset (removed battery) I get some different values with cpu-z. 2-2-2-6 I don't understand why I get those values in CPU-Z. I don't believe that my system is running with those settings. I think it's running with default bios 1.2 settings 2,5-4-4-6 but who knows?
A lot of users had dead MOBO's when they flashed to v1.4. The reason isn't found. Some moderators say the didn't wait for the DOS prompt after flashing (Could be) Some users can confirm they did. Maybe it has to do with the corsair memory. If you do a search you will find a lot of usefull information (bios v1.4 and/or MOBO hangs on keyboard initialisation)

875P NEO-FIS2R no boot with memory problems

I just got a NEO FIS2R board, a P4 2.6C, and two 512MB sticks of OCZ PC3200 Premier DDR. I installed the board and connected only my hard drive, video card (GeForce4 Ti4200), both sticks of memory, and CPU (on a 300W PSU). At first, the board would eventually make it to the "booting OS" stage, after spending a little time on "initializing video" (normal) and "assigning ISA" or something like that (don't know what that is, since the board has no ISA slot). Unfortunately, although my monitor's light changed from yellow to green, meaning it was getting a signal, the screen remained blank. I gave it a few minutes and finally turned off the computer. After reseating the video card and memory and disconnecting the hard drive, the same problem occurred. Finally, I took out one of the sticks. After this, the computer hung on that ISA thing for about ten seconds, and then went back to "detecting memory" and gave a 2-1 error beep. I switched between the two OCZ sticks and also two sticks slow generic PC2100 memory that I had in my old computer and I know work fine. Eventually the computer stopped pausing at the ISA stage and went to the memory detection after only a second or so. Since the video was obviously acting strange, I disconnected the video card so the computer contained only CPU and memory. The bootup sequence was the same, except that in place of the single beep during video intialization, it gave me a 2-8 error code. Finally, I took the board out of my case and laid it flat on the wooden table and tried again. Still no boot. I also cleared CMOS several times throughout this procedure, so that shouldn't be the problem.
Can anyone figure out what's going on here? It's especially confusing to me that the computer booted all the way (sans video) at first, then started having memory problems, and that the system passes the initial memory test but then goes back to it after that ISA thing (this is all according to the D-Bracket).

Quote
On the compatability list, it says
"Kingston KVR400X64C25/512
W942508BH-5 (Winbond)"
Since the memory I am looking at is CL2, does that mean it might not be compatible after all?
If you're wondering whether the Kingston HyperX RAM you're looking at is the same as the Kingston RAM you've found on the compatibililty list, the answer is NO. The RAM from the list that you're referring to has a model number that starts with "KVR", which stands for "Kingston Value RAM". HyperX RAM has model numbers that start with the letters "KHX".
You might also note that there is no listing for any of the HyperX stuff on that compatibility chart. However, I have seen posts from several people on this forum who seem to be using HyperX RAM with no problem. I suspect that MSI hasn't updated that list in awhile, because there are no listings for many of the newer PC 3500, 3700, and 4000 RAM models.
I personally went 512mb (2x256) of OCZ PC3200EL DDR RAM, it is listed as 'OCZ (PN- OCZ400256EL ) PN- OCZ400256EL' on the compatibility chart. I had plenty of problems trying to run a set of Corsair TwinX 3200PCT ver. 1.2 on my 875P NEO board, and I settled them by switching over to the OCZ RAM only because it was listed. While it wasn't my first choice I'm pretty happy with it because so far it's been running stable at CAS 2,2,3,6, with the voltage at 2.65.

875P Neo-L Boot fail, mixed D-LED errs.

Hello all pros :D.
I'll start this off with the basics, my system specs:
MSI 875P Neo-L (BIOS 1.6)
Pentium 4 3Ghz HT CPU (Frequency locked)
Zalman CNPS7000-AL CU cpu cooler (Artic Silver thermal grease)
TwinMOS 512 MB PC3200 CL2.5 (2.5-3-3-8/auto) memory
IBM DeskStar 75GXP IDE ATA100 HDD (attached to primary channel, master)
Asus GeForce 4 Ti4800SE AGP 8X 128 MB DDR graphics card
460W LePont/SuperFlower ATX P4-certified PSU
Dual PAPST 12DBa 80MM case fans (intake & exhaust)
Fong Kai FK-603 Midi-tower ATX case
Keytronic standard Swedish-layout PS/2 keyboard
Microsoft Intellimouse explorer 3.0 optical USB
Windows XP SP1 Pro English
Generic floppy drive
I've used the following BIOS settings in my tests:
Fail safe defaults and Optimized defaults
- Tried to enable/disable: FDD Controller, HT, onboard LAN, with no effect on the problem. Other settings follows (different also tried): slow memory settings, 2.60-70V memory voltage, 128 MB AGP arperture size. All others standard.
BIOS 1.6 runs the best, 1.7 has the same effect as all the other lower revs. The problem persists in 1.8 but also decreases system performance noticeably.
The actual problem:
The system refuses to boot up. In 40 cases the system boots once.
The D-LED's signals either a keyboard controller init msg or AGP init msg, randomly.
In the cases where the system does not boot, it does not either light the case front panel's power LED or signal any HDD activity (drive gets spun up due to poweron, etc).
The system does not beep in any way when it refuses to boot correctly.
I've tried changing the PSU for a enermax 430W one with no effect (voltages were ok with both), tried changed memory for some TwinMOS-winbond with no effect, tried changing graphics card for a MSI GeForce 4 MX 440 AGP with no effect, tried to boot without HDD attached with no effect, tried to use other PS/2 mouse and keyboard and without both without any effect, verified clock battery to be fully functional (tried with brand new battery also), removed and also replaced floppy drive with no effect, had machine unplugged for over 120 minutes without bios battery for total reset with no effect, tried to boot machine without AGP card at all - no error beep/change in D-LED info or likewise effect, tried to boot machine without RAM at all - no error beep/change in D-LED info or likewise effect.
When the machine is operating CPU temperatures are within normal ranges (43-53 C) and the CPU does not throttle down the speed.
Typical error flowscheme:
System running -> I shut it down or choose reboot -> System powers down and fails to powerup with one of the above D-LED infos.
->
I have to hold down power for 3-4 secs for the system to poweroff, then turn it on again and repeat 15-75 times until system boots up.
->
BIOS settings checksum fails, press F1 and go into the bios to typically raise memory voltage and AGP arperture size.
->
Machine shuts down when choosing save and fails to powerup.
->
I have to hold down power for 3-4 secs for the system to poweroff, then turn it on again and repeat 15-75 times until system boots up. System runs fine until I have to do step one again.
As you can guess this is becoming something of a problem.
I got the motherboard & CPU from MSI via DHL delivery when I won a web-contest they had for the board when it was new so I have to send it all the way to Taiwan to RMA it according to my local MSI dealer (which would take 3-7 weeks and cost several hundred in postage with a secure delivery firm like DHL). As the computer is my bread and butter literally as I'm a student, this is not a good choice.
As you can read above I've narrowed it down to be either the CPU or Motherboard with a 99.99% assurance, and I'm kind of betting it is the motherboard.
So does anyone here have an idea what to do? I've read over 15 threads about this board and tried random suggested stuff for all kinds of problems with no effect to my situation.
Any help at all would be greatly appriciated.
Henric Blomgren

I emailed MSI's support now once again with the same message I included in the top (and went through the autoresponder-resent procedure), no answer yet but we'll see if they get back to me this time. Otherwise I'm starting to doubt if I will ever get it sorted =/
If so, is the Neo2 boards with the 865PE chipsets more or less as good, as I won't be able to afford one of those 875P Neo boards to replace my current one?
/Henric

Is PXE network booting supported on 875p Neo FIS2R?

Hi all,
I have spent a full day trying to get my computer to boot via PXE from a remote server. My computer is equipped with an MSI 875p Neo FIS2R motherboard.
relevant stats are as follows:
Motherboard: MSI 875p Neo FIS2R
Ethernet Card: Integrated on Motherboard (Intel 82547EI (CSA Interface Gigabit LAN))
The PXE server to which I am trying to connect is running Windows 2000 Server and is configured with Windows Remote Installation Service. The server has been tested with another pxe client (my laptop) and I am able to boot over the network succesfully. It looks like everything is configured properly on the server side.
I am using the msi motherboard's Intel 82547EI integrated ethernet controller when attempting to connect to the server. I do not have another PCI ethernet controller that I can try as an alternative.
I could not find any mention of network booting in the boot sequence section of the BIOS configuration, nor anywhere else in the BIOS settings. I have made sure the integrated ethernet controller is enabled in the BIOS.
I also upgraded the BIOS to the most recent version (2.4) but there is still no sign of any 'network boot' settings in the boot sequence nor anywhere else in the BIOS settings.
See the following webpage for the BIOS versions:
http://www.msicomputer.com/support/bios_result.asp?platform=Intel&model=875P%20Neo-LSR/FIS2R%20(MS-6758%20PCBv1)&newsearch=1
Note that BIOS version 2.2 specifically mentions:
"This BIOS fixes the following problems of the previous version:
- System cannot login to PXE server without floppy drive installed."
This seems to suggest that the motherboard supports PXE. While I do not have a floppy drive installed on my machine, this BIOS update indicates that a lack of a floppy drive should not pose a problem.
When booting the computer I am presented with a few keystroke options, one of which is to press F12 for a 'Network Boot'. After pressing F12 I receive no indication that the computer is attempting to contact a PXE server and the computer boots into Windows XP as usual.
I have searched the MSI forums and have yet to come across a solution. Signs point to there being PXE support but I must be missing something. Can anyone give me any definitive answers here? Thanks in advance.

I've since been in contact with MSI technical support. Oddly they cannot seem give me a definitive answer on the support of PXE in MSI motherboards so again I'm turning to you guys. I'm really hoping someone out there has some experience with PXE and any sort of MSI motherboard. Surely someone must have run into this issue before. Anyone? Anyone at all?

My USB mouse doesn't always start at boot.

After updating from Arch 0.7.1 to 0.8, one of the big pile of bugs I had was that my USB mouse doesn't always start at boot. In fact, when I start the computer, the red LED in the mouse lights up but sometimes it switches off after the menu where I can choose to use Arch linux or .. Arch linux.
So, the mouse switches off before I startx one time on two. When it happens I just deplug and replug it but I hate to do that.
Need some help.

dmesg when the mouse isn't working :
$ dmesg
Linux version 2.6.19-ARCH (root@Laptop) (gcc version 4.1.2 20061215 (prerelease)
) #1 SMP PREEMPT Thu Jan 11 20:08:17 CET 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ec000 - 00000000000f0000 (ACPI NVS)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000f800000 (usable)
BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
248MB LOWMEM available.
Entering add_active_range(0, 0, 63488) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 63488
HighMem 63488 -> 63488
early_node_map[1] active PFN ranges
0: 0 -> 63488
On node 0 totalpages: 63488
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 464 pages used for memmap
Normal zone: 58928 pages, LIFO batch:15
HighMem zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP (v000 COMPAQ ) @ 0x000ec010
ACPI: RSDT (v001 COMPAQ HAWA7K31 0x00010503 0x00000000) @ 0x000ec080
ACPI: FADT (v001 COMPAQ HAWA7K31 0x00010503 0x00000000) @ 0x000ec0cc
ACPI: SSDT (v001 COMPAQ HAWA7K3 0x00000001 MSFT 0x0100000c) @ 0x000ec223
ACPI: DSDT (v001 COMPAQ DSDTTBL 0x00000001 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0xee08
Allocating PCI resources starting at 10000000 (gap: 0f800000:f07c0000)
Detected 901.637 MHz processor.
Built 1 zonelists. Total pages: 62992
Kernel command line: root=/dev/hda3 ro earlymodules=piix
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (011fa000)
Enabling fast FPU save and restore... done.
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 246968k/253952k available (2330k kernel code, 6392k reserved, 735k data,
260k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfff83000 - 0xfffff000 ( 496 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xd0000000 - 0xff7fe000 ( 759 MB)
lowmem : 0xc0000000 - 0xcf800000 ( 248 MB)
.init : 0xc0405000 - 0xc0446000 ( 260 kB)
.data : 0xc0346806 - 0xc03fe64c ( 735 kB)
.text : 0xc0100000 - 0xc0346806 (2330 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1805.52 BogoMIPS (lpj=3611040)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0183f9ff c1c7f9ff 00000000 00000000 00000000
00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 64K (64 bytes/line)
CPU: After all inits, caps: 0183f9ff c1c7f9ff 00000000 00000420 00000000 0000000
0 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
checking if image is initramfs... it is
Freeing initrd memory: 501k freed
ACPI: Core revision 20060707
ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
ACPI: setting ELCR to 0200 (from 0c28)
CPU0: AMD Duron(tm) Processor stepping 01
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfa154, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs *3 4 5 6 7 10 11 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 15)
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [_SB_.PCI0] bus is 0
PCI quirk: region ee00-eeff claimed by vt82c586 ACPI
PCI quirk: region ec00-ec0f claimed by vt82c686 SMB
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [_SB_.PCI0._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:0b: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0b: ioport range 0xee00-0xee7f could not be reserved
pnp: 00:0b: ioport range 0xee80-0xeeff has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: 80000000-800fffff
PREFETCH window: 88000000-8fffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 98304 bytes)
TCP bind hash table entries: 4096 (order: 3, 49152 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
apm: BIOS not found.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 [email protected]).
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Disabling Via external APIC routing
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PBTN]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:03: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PCI: Enabling device 0000:00:03.0 (0000 -> 0001)
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 3
PCI: setting IRQ 3 as level-triggered
ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKA] -> GSI 3 (level, low) -> IRQ
3
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 260k freed
Time: tsc clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:14.1
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci0000:00:14.1
ide0: BM-DMA at 0x1880-0x1887, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1888-0x188f, BIOS settings: hdc:pio, hdd:DMA
Probing IDE interface ide0...
hda: QUANTUM FIREBALLlct20 40, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdd: Compaq CRD-8322B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 78177792 sectors (40027 MB) w/418KiB Cache, CHS=65535/16/63
hda: cache flushes not supported
hda: hda1 hda2 hda3
hdd: ATAPI 32X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Linux agpgart interface v0.101 (c) Dave Jones
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:14.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ
11
uhci_hcd 0000:00:14.2: UHCI Host Controller
uhci_hcd 0000:00:14.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:14.2: irq 11, io base 0x00001840
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:14.3[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ
11
uhci_hcd 0000:00:14.3: UHCI Host Controller
uhci_hcd 0000:00:14.3: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:14.3: irq 11, io base 0x00001860
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
agpgart: AGP aperture is 64M @ 0x90000000
usb 1-1: new low speed USB device using uhci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
usb 1-2: new full speed USB device using uhci_hcd and address 3
usb 1-2: configuration #1 chosen from 1 choice
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,EC
P]
parport_pc: VIA parallel port: io=0x378, irq=7
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:14.5[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ
10
PCI: Setting latency timer of device 0000:00:14.5 to 64
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
input: PC Speaker as /class/input/input1
via686a 0000:00:14.4: base address not set - upgrade BIOS or use force_addr=0xad
dr
vt596_smbus 0000:00:14.4: SMBUS: Error: Host SMBus controller not enabled! - upg
rade BIOS or use force=1
via-rhine.c:v1.10-LK1.4.2 Sept-11-2006 Written by Donald Becker
PCI: Enabling device 0000:00:05.0 (0004 -> 0007)
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ
5
eth0: VIA Rhine II at 0x11000, 00:05:5d:e9:5a:17, IRQ 5.
eth0: MII PHY found at address 8, status 0x782d advertising 01e1 Link 0021.
usbcore: registered new interface driver hiddev
usbhid: probe of 1-1:1.0 failed with error -71
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Initializing USB Mass Storage driver...
lp0: using parport0 (interrupt-driven).
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
Real Time Clock Driver v1.12ac
ppdev: user-space parallel port driver
EXT3 FS on hda3, internal journal
Adding 262576k swap on /dev/hda2. Priority:-1 extents:1 across:262576k
scsi 0:0:0:0: Direct-Access JetFlash TS256MJF110 0.00 PQ: 0 ANSI: 2
usb-storage: device scan complete
eth0: link up, 10Mbps, half-duplex, lpa 0x0021
SCSI device sda: 512000 512-byte hdwr sectors (262 MB)
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 512000 512-byte hdwr sectors (262 MB)
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
sda: sda1
sd 0:0:0:0: Attached scsi removable disk sda
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 3 (level, low) -> IRQ
3
[drm] Initialized savage 2.4.1 20050313 on minor 0
mtrr: base(0x8a000000) is not aligned on a size(0x5000000) boundary
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
eth0: no IPv6 routers present
mtrr: base(0x8a000000) is not aligned on a size(0x5000000) boundary
mtrr: base(0x8a000000) is not aligned on a size(0x5000000) boundary
mtrr: base(0x8a000000) is not aligned on a size(0x5000000) boundary
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
And here's the output of dmesg when the mouse works :
$ dmesg
Linux version 2.6.19-ARCH (root@Laptop) (gcc version 4.1.2 20061215 (prerelease
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ec000 - 00000000000f0000 (ACPI NVS)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000f800000 (usable)
BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
248MB LOWMEM available.
Entering add_active_range(0, 0, 63488) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 63488
HighMem 63488 -> 63488
early_node_map[1] active PFN ranges
0: 0 -> 63488
On node 0 totalpages: 63488
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 464 pages used for memmap
Normal zone: 58928 pages, LIFO batch:15
HighMem zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP (v000 COMPAQ ) @ 0x000ec010
ACPI: RSDT (v001 COMPAQ HAWA7K31 0x00010503 0x00000000) @ 0x000ec080
ACPI: FADT (v001 COMPAQ HAWA7K31 0x00010503 0x00000000) @ 0x000ec0cc
ACPI: SSDT (v001 COMPAQ HAWA7K3 0x00000001 MSFT 0x0100000c) @ 0x000ec223
ACPI: DSDT (v001 COMPAQ DSDTTBL 0x00000001 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0xee08
Allocating PCI resources starting at 10000000 (gap: 0f800000:f07c0000)
Detected 901.637 MHz processor.
Built 1 zonelists. Total pages: 62992
Kernel command line: root=/dev/hda3 ro earlymodules=piix
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (011fa000)
Enabling fast FPU save and restore... done.
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 4096 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 246968k/253952k available (2330k kernel code, 6392k reserved, 735k data
virtual kernel memory layout:
fixmap : 0xfff83000 - 0xfffff000 ( 496 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xd0000000 - 0xff7fe000 ( 759 MB)
lowmem : 0xc0000000 - 0xcf800000 ( 248 MB)
.init : 0xc0405000 - 0xc0446000 ( 260 kB)
.data : 0xc0346806 - 0xc03fe64c ( 735 kB)
.text : 0xc0100000 - 0xc0346806 (2330 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1805.52 BogoMIPS (lpj=3611040)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0183f9ff c1c7f9ff 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 64K (64 bytes/line)
CPU: After all inits, caps: 0183f9ff c1c7f9ff 00000000 00000420 00000000 000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
checking if image is initramfs... it is
Freeing initrd memory: 501k freed
ACPI: Core revision 20060707
ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
ACPI: setting ELCR to 0200 (from 0c28)
CPU0: AMD Duron(tm) Processor stepping 01
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfa154, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs *3 4 5 6 7 10 11 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 15)
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [_SB_.PCI0] bus is 0
PCI quirk: region ee00-eeff claimed by vt82c586 ACPI
PCI quirk: region ec00-ec0f claimed by vt82c686 SMB
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [_SB_.PCI0._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
pnp: 00:0b: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0b: ioport range 0xee00-0xee7f could not be reserved
pnp: 00:0b: ioport range 0xee80-0xeeff has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: 80000000-800fffff
PREFETCH window: 88000000-8fffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 98304 bytes)
TCP bind hash table entries: 4096 (order: 3, 49152 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
apm: BIOS not found.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 [email protected]).
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Disabling Via external APIC routing
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PBTN]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:03: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PCI: Enabling device 0000:00:03.0 (0000 -> 0001)
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 3
PCI: setting IRQ 3 as level-triggered
ACPI: PCI Interrupt 0000:00:03.0[A] -> Link [LNKA] -> GSI 3 (level, low) -> IRQ
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 260k freed
Time: tsc clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:14.1
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci0000:00:14.1
ide0: BM-DMA at 0x1880-0x1887, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1888-0x188f, BIOS settings: hdc:pio, hdd:DMA
Probing IDE interface ide0...
hda: QUANTUM FIREBALLlct20 40, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdd: Compaq CRD-8322B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 78177792 sectors (40027 MB) w/418KiB Cache, CHS=65535/16/63
hda: cache flushes not supported
hda: hda1 hda2 hda3
hdd: ATAPI 32X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Linux agpgart interface v0.101 (c) Dave Jones
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:14.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IR
uhci_hcd 0000:00:14.2: UHCI Host Controller
uhci_hcd 0000:00:14.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:14.2: irq 11, io base 0x00001840
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:14.3[D] -> Link [LNKD] -> GSI 11 (level, low) -> IR
uhci_hcd 0000:00:14.3: UHCI Host Controller
uhci_hcd 0000:00:14.3: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:14.3: irq 11, io base 0x00001860
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
agpgart: AGP aperture is 64M @ 0x90000000
usb 1-1: new low speed USB device using uhci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
usb 1-2: new full speed USB device using uhci_hcd and address 3
usb 1-2: configuration #1 chosen from 1 choice
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,E
parport_pc: VIA parallel port: io=0x378, irq=7
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:14.5[C] -> Link [LNKC] -> GSI 10 (level, low) -> IR
PCI: Setting latency timer of device 0000:00:14.5 to 64
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
input: PC Speaker as /class/input/input1
via686a 0000:00:14.4: base address not set - upgrade BIOS or use force_addr=0xa
vt596_smbus 0000:00:14.4: SMBUS: Error: Host SMBus controller not enabled! - up
via-rhine.c:v1.10-LK1.4.2 Sept-11-2006 Written by Donald Becker
PCI: Enabling device 0000:00:05.0 (0004 -> 0007)
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ
eth0: VIA Rhine II at 0x11000, 00:05:5d:e9:5a:17, IRQ 5.
eth0: MII PHY found at address 8, status 0x782d advertising 01e1 Link 0021.
usbcore: registered new interface driver hiddev
usbhid: probe of 1-1:1.0 failed with error -71
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Initializing USB Mass Storage driver...
lp0: using parport0 (interrupt-driven).
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
Real Time Clock Driver v1.12ac
ppdev: user-space parallel port driver
EXT3 FS on hda3, internal journal
Adding 262576k swap on /dev/hda2. Priority:-1 extents:1 across:262576k
scsi 0:0:0:0: Direct-Access JetFlash TS256MJF110 0.00 PQ: 0 ANSI: 2
usb-storage: device scan complete
eth0: link up, 10Mbps, half-duplex, lpa 0x0021
SCSI device sda: 512000 512-byte hdwr sectors (262 MB)
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 512000 512-byte hdwr sectors (262 MB)
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
sda: sda1
sd 0:0:0:0: Attached scsi removable disk sda
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 3 (level, low) -> IRQ
[drm] Initialized savage 2.4.1 20050313 on minor 0
mtrr: base(0x8a000000) is not aligned on a size(0x5000000) boundary
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
eth0: no IPv6 routers present
mtrr: base(0x8a000000) is not aligned on a size(0x5000000) boundary
mtrr: base(0x8a000000) is not aligned on a size(0x5000000) boundary
mtrr: base(0x8a000000) is not aligned on a size(0x5000000) boundary
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
usb 1-1: USB disconnect, address 2
usb 1-2: USB disconnect, address 3
usb 1-1: new low speed USB device using uhci_hcd and address 4
usb 1-1: configuration #1 chosen from 1 choice
input: HID 062a:0000 as /class/input/input2
input: USB HID v1.10 Mouse [HID 062a:0000] on usb-0000:00:14.2-1

[875P Neo Series] USB Flash Drive Boot?

I've got a 875P Neo-FIS2R MB, MS-6758 (v.1.x) with AMI Bios 1.6. Before purchasing a USB Flash drive, I'd like to know whether this MB can boot from it.
Any help appreciated

See the link in my signature. You should be able to.

875p Neo - PC halts on Cold Boot (Initalising Keyboard)

Everytime I press the power on button on my PC you can hear the power start up, cd and dvd rom light come on and hard disk light comes on for a short period of time. If you then press reset or press the power on and off again - it all springs to life !!!!! !!!
:O This problem is Pi*#ng me right off!!! Loads of people are complaining of it - what are you doing about it MSI???
I Cleared the Cmos, upgraded to 1.4 bios but that made no difference.
My spec is:
· Enermax 430watt PSU
· MSI 875P Neo-FIS2R Motherboard
· Intel P4 3ghz, 800fsb Processor
· 2 Geil PC3200 400Mhz 512mb Memory Modules
· Clean install of Windows 2000 Professional
· Coolermaster 201 Aluminium ATX Case
· Western Digital Caviar Special Edition 100GB HD
· Sony DRU-500AX DVD Writer
· NEC DVD Rom
· Gainward Geforce4 Ti4200 X8 AGP with 128mb DDR Ram
. Videologic Sonic Fury Soundcard
· HCS PCI 56k Modem
I looked at the MSI manual, which said to look at the back of the machine at the D-Bracket LED’s, which is supposed to tell you what is wrong. Every time the fault happened the LED’s pattern (according to the manual codes on page 10) showed that it was the “Initialising Keyboard Controller”.
I Changed the Keyboard but the problem still exists. I pulled the machine apart bit by bit to see if any one piece of hardware was the cause - but the problem still occurred! I even tried another PSU and hard disk but NOOOOOOOOO! didn't work.
My mem timings are set by SPD and I have tried lower settings.
I have sent a more detailed version of this to MSI Tech Support 3 days ago - BUT HEARD NOTHING. Arrrrrggggghhhh !!
Anyone with any solutions??? PLEASE HELP!!!!
Trevor Hatley.

Thanks guys, I'll keep that in mind, but I have just heard from my retailer that they are sending me a brand new motherboard!! Wahoooo! Great service from http://www.pcupgrade.co.uk
Do you think I should upgrade to 1.5 bios when I get my replacement mobo????
Anyone had any 1.5 problems??
Please let me have your comments.
Thanks,
T Hatley.

875p neo doesn't always boot

Similar Messages

Maybe you are looking for