875P Neo-FIS2R File Copy errors loading Win XP Pro

While installing WinXP Pro SP 1 I get file copy failures on random files two or three times during the install. Retry succeeds on the file, but errors keep coming up after install randomly. Explorer crashes on logon, files are corrupt, etc. Tried two different MBs, two different CPUs, two different PSUs, two different sets of RAM, different IDE cables, booting from both DVD Drives, different Win XP CDs. I also tried the same with a Gigabyte 875 board and had exactly the same problem. With the Gigabyte board, if I ran the bus with a setting of 190 or 195 instead of 200MHz, the system ran fine, but then my 2.8GHz CPU is running at 2.66GHz. I can't go slower than 200MHz (but I did try 201 and 202; same errors) on the Neo-FIS2R so I can't find a setting that is stable and that's the board I'd like to be running. Any ideas about what's causing all of these combinations from running stable at a stock setting of 2.8GHz?
Thanks.
Mike Wolfe
P4 2.8C @FSB 200, HT Enabled
Corsair Platinum TwinX DDR400 2x256MB
875P Neo-FIS2R Bios Version 1.8
ATI AIW 9600 Pro 128MB No OC
PowerUp 350W Power Supply
WD2000JB 200GB; Master on IDE 1; No S-ATA
Sony DDU 1621 16x DVD ROM Master on IDE2
Sony DRU-510A DVD+-R/RW Slave on IDE2
BIOS Defaults - 200MHz CPU Bus - DDR Voltage 2.7V
On Board Promise Disabled; IDE Bus Master; P-ATA Only

I am also having trouble with this on xp pro. When fully installed I get many random errors. New at this but have read that if you install a partition more than 137 gb data corruption may occur. So I partitioned the drive 20, 70, 70, and installed xp pro on the 20 gb partition. Per mb and hdd manuals I installed xp sp1. I am still getting random errors. This is the only hdd. Maxtor 160 gb ata 133 on ide1. Is it impossible to run the system this way? It gives me random crashes and stop requests. It also at one point gave me erros saying the cdrom memory is corrupt. Is the hdd drive sze possibly the problem?
MSI 875p max fisr
corsair twinx xms 333 1 gb
ati raideon all in wonder
samsung 352 cdrw
antec 430w true power
3.0 g intel p4

Similar Messages

875P Neo-FIS2R Dead

Hi,
I just built a new machine with the 875P Neo-FIS2R, and it was working fine. I read that there were problems with the BIOS V1.3. Of course, I had to update my BIOS. I saw V1.4 was out and figured it was safe and fixed. So I used MSI's LIVE BIOS to flash the BIOS in Windows mode. I have done this before with my other MSI board and had no problems. The flashing process went successful, and asked me to reboot. Then when I did it never came back up. No video or POST beep. I tried switching out memory, clearing the CMOS, and even changing to my older GF3 card. Nothing worked. Can someone tell me what to do? I want my PC to work.... Again.
Pentium 4 3.0C
1 GB Corsair Twinx
36 GB SATA Raptor
MSI Neo-FIS2R
Radeon 9800 Pro 256 MB
SB Audigy 2

I took out the battery and tried but it didn't work. Then I took a stick of pc2100 ddr out of my older machine and put it in, and it booted! Then I swapped out back to my new ddr 400 and it booted! Okay, so now when it boots, it says no BIOS installed and acts like I never had win xp on it. So thats alright, I can reload it, but My Cmos is like it was in 1999. Do I just load the defaults then fix it back to where it was and reload windows? Or do I need to slow down dram timings and reload windows and flash bios back to V1.2?

875P Neo FIS2R-Slow boot with Raid on Intel + Raid on Promise

Hello all.
Here is the configuration I'm trying to set up (and almost did)
SI 875P Neo FIS2R,MS-6758 BIOS v2.4
P4 2.6 GHz HT
500W 6fan total
2x1G Kit DDR 400
2x74 G WD Raptor Raid0 (Intel S1-2) Win XP inst
2x36 G WD Raptor Raid0 (Promise S3-4)
GeCube X1600Pro
DVD-RW (IDE 2 )
Win XP SP2 (All latest updates installed)
I followed the instructions as they are listed in the sticky (great job btw) and configured the 2 SATA 74G WD Raptor on Intel Raid controller(serial1&2) as Raid0 and install WindowsXP Prof sp 2 on it.
Then I configured the 2 SATA 36G WD Raptor on Promise controller(serial3&4) as Raid0 and added this Raid to the existing WindowsXP installation.
This set up is working very good once I'm logged into Windows with no problems at all.
The glitch is that I need 3 min waiting time till I see the windows loading logo.
I have all the latest drivers installed also IAA and INFs and my bios is as the default values except the changes mentioned in the sticky
Onboard Promise IDE - as Raid
ON-Chip IDE Configuration:
Native Mode
SATA Only
Keep SATA Active - Yes
Keep PATA Active - Yes
PATA Channel selection - Both
Configure SATA as Raid - Yes
I did the Win XP installation twice till now, taking care to install INFs and drivers in the right order but the result is the same...3-5 mins till I have a fully operational windows environment and after that all is running like a dream.
Now, I've searched in the forum and saw that many more people have the same problem but never read the solution to it, so if someone has ever found the way to solve this or has the same configuration please tell me how he did it. Even if someone knows that it can't be solved just drop me a line telling me so. Altough the system is running smoothly I find the 3 min waiting time unacceptable and frustrating. I've run out of ideas so please help me.
Thanks in advance

Hello Blazer and thank you for replying.
Answering one at a time...
are both raid arrays setup with the same stripe size?--> Yes Both arrays are configured at 16k stripes
do you see both the intel and the promise bios setup screens?-->Yes both screens (Intel(R) RAID... and Fast Built (tm) ...)appear almost instantly after MSI's logo screen showing my Raid arrays in Normal status. The delay starts after the Promise's screen till the Windows Loading logo screen.
how is the raid bootable drive identified in the boot from menu?-->
Boot Device Priority:
1st BBS-0 (Raid): Intel <name> (---> this is the OS drive on Intel controller)
2nd Disabled
3rd Disabled
Try other boot devices NO
I have also the option to select the the Drive on Promise which shows as BBS-1 (Raid) FT 378 Ary 1 but I have left it out cause it doesn't have the OS on it.
is the OS drive labeled as C: and seen as 200GB drive [as one] from the four drive array]--> No as it shouldn't cause these are two different Raid Arrays. The first Raid on Intel's controller with the 2x74G WD Disks indeed shows as one C: 137 G and has the OS on it. The second on Promise controller with 2x36G WD Disks also shows as one D: 70G.These are two separate Arrays with 2 disks each and they show as indented.
is network boot enabled causing a delayed boot?--> I don't quit understand what you mean. In case you mean what happens if I unplug the 2 disks from the promise controller then yes if I do that the system boots fast in the Windows even if I leave the Bios setting "configure promise as raid"!!!
My problem is similar with this post: https://forum-en.msi.com/index.php?topic=69994.0
other posts that have reported the same trouble:
https://forum-en.msi.com/index.php?topic=94944.msg683258#msg683258
https://forum-en.msi.com/index.php?topic=81901.0
https://forum-en.msi.com/index.php?topic=66662.0
https://forum-en.msi.com/index.php?topic=98005.0 ---> I wish it was that simple, I did it as with all other drivers
I hope that info helps you helping me.

Need help w/ 875P Neo-FIS2R

875P Neo-FIS2R BIOS V 1.2
Intel CPU 2.8 FSB 800mhz
Corsair XMS Twin 512 (256 x 2)Dual Channel DDR 400 C2 LLPT
Sony DVD+R DRU500A (internal)
PowerColor Radeon 9700 Pro Evil Commando 2 AGP 128
Planar LCD 20" monitor DVI
Windows XP Pro
2 Western Digital ATA-100 100gig hardrives
Harddrives are only thing I kept from old system; unfortunately, I forgot to delete video drivers before installing in new system. Computer boots starts loading Win XP Pro then screen goes blank, Planar LCD monitor says no signal, so I figure the problem is the the AGP video card since I get this far. Windows won't load in safe mode either, screen just blanks monitor says no signal and it restarts with same results. I have changed BIOS settings to reflect 128 AGP aperture. LED monitor(in back)shows 1, 2 & 4 green and only 3 red. I am afraid to use flash utility to upgrade BIOS. I would prefer to upgrade via LiveUpdate. Help me get into windows via safe mode so I can uninstall old video drivers and install new video drivers.
Thx for your help.

Sorry,but if I got that right,u got a complete new system except the hdd´s.
But even with a "mobo only" change of ur system u should better make a complete windows new install.

875P neos fis2r IDE 3 Question

I have a raid 0 setup on the promise SER3 and SER4 connectors=sata
I also have a normal IDE 80 gig that I use for internal music and such. It is alone, no slave with it.
It was connected to IDE1, but it is soo crammed in there that I decided to move i down below by the SER 3 and SER 4.
My cdrom and dvd are master slave on IDE2.
So, when I boot up, my 80 gig on IDE3 is not detected, nor shows up in disk manager.
How to get it to "notice" it?
I also have an external esata 500 gig on ser1.
Any Suggestions?

Thanks for responding Leekh
the mobo 875p neo fis2r has 3 ides. 1 and 2 are next to eachother, then the floppy A next to those.
side by side. IDE 3 is down below-(yellow) next to ser3 ser 4 1st generation sata connetors.
I Have cdrom/dvd as /master slave on IDE1,
I moved my 80 gig-xtra drive to IDE 3.-because it was a crammed fir in IDE2.
my OS is setup on c drive raid 0 with 2x150 gigs via the ser3and ser4 mentioned above.
to better clarifysee page 2-18 of the manual
IDE1 blue IDE 2 white
here is a pic IDE3 is yellow,
to clarify my whole system.
my os is on raid0 on the connectors below the yellow. I have one esata 500 gig connected to the bottom orange, ABOVE the yellow. the other one is unoccupied.
I switched an internal HD from IDE2, to IDE3 (yellow above)-and I cannot get it detected for some reason. I do not know if it is a bios config or not, I go in there,look for 2 secs, and wanna runaway crying to my mommy.
I copy and paste a review part here.
" Like all motherboards with an 875P/ICH5(R) chipset combination, there are two Serial ATA connectors located next to the ICH5 South Bridge (ICH5R in the 875P Neo-FIS2R's case). As you may or may not already know, this new South Bridge controls both SATA connectors and in fact allows a stream of 266MB/s of data instead of the slower, PCI bus constrained 133MB/s which can get awfully clogged with having to attend to other needy components. Read through our 875P chipset review to understand the benefits of placing the Serial ATA controller in the South Bridge as opposed to a separate PCI Serial ATA controller.
" We are very pleased to see that the 875P Neo-FIS2R contains exceptional IDE/Serial ATA drive support. As is always the case there are two standard IDE connectors, dubbed the Primary and Secondary IDE connectors, which support two channels each or up to four IDE drives total.
The 875P Neo-FIS2R's Promise PDC20378 controller powers the third IDE controller on this motherboard, and is capable of supporting exactly two IDE drives. This same Promise PDC20378 controller also powers two Serial ATA connectors in addition to the two ICH5-bound Serial ATA connectors. You'll be able to connect one drive to each of the four SATA connectors powered by the ICH5 and Promise SATA connectors. So in total, you'll be able to connect four SATA and six IDE drives to this motherboard, which equals a grand total of ten possible drives that can be connected to this motherboard. As we said in our ASUS P4C800 Deluxe review, most desktop users will find this feature to be nice instead of necessary; but there will always be those who desire this capability for something a little more potent than desktop usage. "
http://www.anandtech.com/mb/showdoc.aspx?i=1820&p=2

Probems with msi 875p neo Fis2r and network controller driver

Hi guys just wondering if anyone could help me with my msi 875p neo FIS2R and problems with the network controller driver/network card.
I'm running xp on a computer my nextdoor neighbour gave me. I got it working fine with service pack 3 installed but then installed a bunch of windows updates last night and the computer would switch itself off before windows could start. Now I reinstalled xp and unfortunately it does not recognise the network controller/card at all now. I tried installing the intel network controller drivers but it stopped because it said no intel adapter/card was installed/present. Could anyone please help with suggestions? I tried running everest and under newtwork it doesnt list intel network adapters but I'm pretty certain it is. Again any suggestions?
--------[ EVEREST Home Edition (c) 2003-2005 Lavalys, Inc. ]
Computer:
Operating System Microsoft Windows XP Professional
OS Service Pack Service Pack 3
DirectX 4.09.00.0904 (DirectX 9.0c)
Motherboard:
CPU Type Intel Pentium 4, 2800 MHz (14 x 200)
Motherboard Name MSI 875P Neo-FIS2R (MS-6758) (5 PCI, 1 AGP, 4 DDR DIMM, Audio, Gigabit LAN, IEEE-1394)
Motherboard Chipset Intel Canterwood i875P
System Memory 1024 MB (PC3200 DDR SDRAM)
BIOS Type AMI (10/11/04)
Partitions:
C: (NTFS) 238464 MB (200326 MB free)
--------[ DMI ]---------------------------------------------------------------------------------------------------------
[ BIOS ]
BIOS Properties:
Vendor American Megatrends Inc.
Version V2.4
Release Date 10/11/2004
Size 512 KB
Boot Devices Floppy Disk, Hard Disk, CD-ROM, ATAPI ZIP, LS-120
Capabilities Flash BIOS, Shadow BIOS, Selectable Boot, EDD, BBS
Supported Standards DMI, APM, ACPI, ESCD, PnP
Expansion Capabilities ISA, PCI, AGP, USB
[ System ]
System Properties:
Manufacturer MICRO-STAR INC.
Product MS-6758
Version 00C
Serial Number 00000000
Wake-Up Type Modem Ring
[ Motherboard ]
Motherboard Properties:
Manufacturer MICRO-STAR INC.
Product MS-6758
Version 00C
Serial Number 00000000
[ Processors / Intel(R) Pentium(R) 4 Processor ]
Processor Properties:
Manufacturer Intel
Version Intel(R) Pentium(R) 4 Processor
External Clock 200 MHz
Maximum Clock 4000 MHz
Current Clock 2800 MHz
Type Central Processor
Voltage 3.3 V, 2.9 V
Status Enabled
Socket Designation FC-478
Network adapters:
Direct Parallel 5.1.2535.0
WAN Miniport (IP) 5.1.2535.0
WAN Miniport (IP) - Packet Scheduler Miniport 5.1.2535.0
WAN Miniport (L2TP) 5.1.2535.0
WAN Miniport (PPPOE) 5.1.2535.0
WAN Miniport (PPTP) 5.1.2535.0

Quote from: Jack t.N. on 14-November-09, 08:00:05
Clear CMOS with your PSU unplugged from A/C power. Then load "Optimized Defaults" in BIOS and retest.
thanks jimi... jack
will try that and post later if it worked... ive never cleared cmos, this sort of thing is relatively new to me but thanks again

875P NEO FIS2R repaired

My board which died with BIOS 1.3 was repaired by the reseller today. I witnessed the process and thought you guys would like to know.
This guy knew from experience that an 800MHz CPU wouldn't work when trying to get the board back to life again, so first of all he put in a 533MHz CPU (don't know core clock, but doesn't matter I guess)
Then he took out my 2x512MB samsung PC3200 and put in a single pc2100 module.
After that he put in this custom (PLC programmer?) card from MSI in a PCI slot and powered up. From the status LEDs on the PLC card he knew it didn't work. Power of and back on: success. Power off and PLC card removed. Power on and boot from floppy to flash BIOS to v1.4. Flash successfull. Power off and power on: dead. Power off, clear CMOS, power on: dead. Power off, remove PC2100 module and insert corsair module (don't know spec, but it had heat-spreader), power on: POST. Entered BIOS and load setup defaults. Reboot: POST. Power off, removed CPU & memory and put my stuff back. Power on: POST.
System repaired.
I asked if it is safe to mess with mem timings in BIOS v1.4. He said that it's possible that the board won't POST then, but that can be cured by CMOS clear and when needed only one memory module (no dual channel) to get the board to POST again.
But I'm not going to try that. SPD is fine for me right now.
System runs great again.

I had the exact same problem with my new 875P Neo FIS2R, but after reading the post from Francois I tried my own little test.
I was upgrading from a 2.26/533 system with 333 memory so, of course, I still had the old CPU and memory. After being hung on the 'Keyboard Init' step on the D-Bracket after my 1.1 to 1.4 BIOS upgrade I swapped the old CPU and memory onto the board. Everything worked fine! I was able to see the 1.4 upgrade took fine.
Afterwards, I removed the old stuff and put the new stuff back on and it still works. I have no idea why, just thought I'd share.

VooDoo uses the MSI 875P Neo-FIS2R Motherboard

Hello All,
Just check at voodoo.com computers and they are offering the MSI™ 875P Neo-FIS2R as the motherboard in their top of the line PC.
Starting price $4,274.25.
From the postings they seem to have resolved the Bios flashing problem. How was never clear in their postings, but they are pretty confident that it was fixed.
Quote from the main Dude there
“The board is still our #1 choice for the i875 platform.”
I know the…….
“The Truth is Out there”

well just out of interest i punched a few selections
now they dont stop emailing me
Hi Steve,
Thank you for taking the time to submit your latest Luxury F-Class Tower configuration to us on our website. You have made some great choices regarding your next PC purchase, the system you put together looks great. Our next step if you are interested is to fine tune your configuration further with one of our technical experts once we have a better idea of what your needs are. Please do not hesitate to contact my VoodooPC Technical Expert Rahul toll-free at 1-888-708-6636 at your earliest convenience.
What's the Voodoo difference? The Voodoo Allure Paint is standard on the F-Class and is a true automotive finish. We use our own Downdraft Bake Booth and we use professional Sata Spray guns to complete the masterpiece. Voodoo was the first to introduce Automotive finishes to the PC Industry, and we set the standard for many companies. Every F-Class system gives you the full benefit of a full three-year comprehensive parts and labor warranty, which includes two-way shipping and backed up with our Premium version of our Lifetime Upgrade Assurance. Premium Upgrade Assurance gives you the option to upgrade your PC anytime you want, for the life of the PC. With Premium Upgrade Assurance we will cover the cost of shipping both ways on major upgrades (for 3 years), we will cover shipping on parts if you just want to buy parts. If you decide to do a major upgrade we will only charge you for one-hour labor maximum, and we will rebuild the entire machine, we'll update all the drivers and firmware, we will re-cable the machine, and we will reinstall and update the Operating System as if the system were new. If you decide to do a major upgrade we will only charge you for one-hour labor maximum, and we will rebuild the entire machine, we'll update all the drivers and firmware, we will re-cable the machine, and we will reinstall and update the Operating System as if the system were new.
We are also in the business of making high-end gaming machines as many of our satisfied customers are extreme gamers but we have our many customers who generally those who want and appreciate the best quality, craftsman & ultra-reliability money can buy - PERIOD. There are no assembly lines here! Voodoo technicians have industry reputation for squeezing maximum performance from components for maximum power and absolute stability. They handcraft each and every machine we build. They take complete ownership of each system (treating each and every machine they build as if it were there own) from start to finish adding up to 40 man hours for just assembly alone! It takes us a full 35 days to build a system and we never go about making any short-cuts or cut corners - from handpicking the best retail parts direct from the manufacturers (no cheap OEM components or dusty old stock here), careful assembly and world-renowned origami cabling for maximum airflow, softwaring (installing Windows and drivers), rigorous testing (it will NOT leave our facilities unless everything is completely fault free), tweaking for maximum performance & ultra-reliability AND we are perhaps known to have the best open box experience in the market when it arrives at your door. We also offer excellent customer service & support, upgrade Assurance & comprehensive warranty. We are also internationally ISO 9002 certified (which some of our other major competitors are not) and have been in computer business since 1991. Perfection simply cannot be rushed...
If you have any questions or need recommendations regarding your next PC purchase, feel free to give me or my Technical Expert Rahul a toll-free call at the number listed below - we would love to hear from you. Thank you for your interest in a VoodooPC and we look forward to hearing from you soon! Have yourself a great day!
Regards,
Richard Watson
40 hrs to screw together a pc and load windows
wonder if they have any vacancies
one think they still will not give is what i asked for
a final price
nice work and profits if you can get it

How much phases power supply does the 875P Neo FIS2R got ??

How much phases power supply does the 875P Neo FIS2R got ?(
And will it be enough for the Prescott ?(

Prescott will be made on a 0.09u process so it should use less power per MHz, I wouldn't worry about that.
According to what I see it has 6 power regulators which usually means 3 phase.

Is the 875P Neo-FIS2R a bad mb?

Like the title says:
Is the 875P Neo-FIS2R a bad motherboad? I can understand that tis is a place where you will find more problems then anything else. But I mostly see motherboard specific problems, that occur on many mb's of the same type. I find that a bit disturbing...
A friend of mine never had any troubles with it, then again, he might not tell me, or he is lucky. But based on his 'good' experience I have a 875P lying here right now.
I cannot use it yet since I am missing a graphic card to go with it, I expect that to arrive next Tuesday. Im a bit nervous now.....
Another question while I'm at it: will both controllers (the Intel and the Promise) work, or are the mutual exclusive. So I guess I mean is: do I have 3 P-ATA connectors on my mb or either 2 or 1??
If it is the latter option, that would be lame, then I would have to insert my PCI card with a pomise controller....

I have to say the 875P is definitely NOT a bad motherboard as long as you have approved components. It works very well for "standard" usage. It has all of the top features from Intel - 875P chipset, 10Gbit CSA, ICH5R, ADI audio, firewire, etc.
I am concerned with some things MSI could/should have done better in the first place:
1. Wrong NB temp (and it seems to be affected by NBFAN)
2. No SFAN speed monitoring though it wouldn't have cost more to put it in ... X(
3. Slow frequency of BIOS release or update fixes vs other "top tier" motherboard manufacturers
4. More issues than others with popular memory modules
5. Confusing or "poorly documented" BIOS features/interface leave tweakers less in control
6. Corecell, DOT & MAT, BIOS are still a work in progress
When you start looking for topnotch performance and stability via tweaking OR major overclocking - that is where it falls short - contrary to what their marketing says.
Read this thread where an 875P owner compares his new Asus P4C800E Deluxe (after his 875P Neo failed and had to go for RMA). I summarize his "review" here:
Quote
Criteria on MSI 875P Neo-FIS2R vs ASUS P4C800E DeLuxe
Ease in setting up P4C800E
Memory compatibility P4C800E
Overclocking
- setting options Neo
- higher performance P4C800E
- lower temperatures P4C800E
- lower voltages P4C800E
Video card compatibility Neo
Hard drive performance Same
Benchmark scores Est. 5% better on Asus vs MSI
Extra Goodies:
ASUS - ability to use USB ARMD devices and emulate them as floppies, HDD, and even CD-ROM
MSI - AUTO overclocking (Captain, etc. on the Neo boards - 5%, 10% etc on the Asus boards) works much better
quote:
... the Asus is much less of a problem child when setting up. So my final ruling is, don't expect much more from the ASUS board, but if you are fed up with your 875P Neo, or are returning/RMA-ing your board anyway, you might be pleasantly surprised with what the ASUS P4C800/E/Deluxe can do for you.
I think you'll find similiar comparisons from 865PE Neo2 users who had tried the P4P800...
So far many have said they're still keeping their MSI boards when RMA comes back
Conclusions:
- Good HW but FW/SW satsifactory~needs_improvement. :]
- If you don't do major tweaking , and want stability + full features, the 875P is a GOOD board overall, IMHO. 8)

Error writing the project file. Error loading type library / dll

Hi all,
I am trying to create a new portal project in PDK.NET. But I am getting this error- "Error writing the project file. Error loading type library / dll". Can anyone tell me how to solve this error.
rgds

I get this same error. Was working fine until I installed the SAP .Net Connector 2.0. Now it does not work even after it was uninstalled. Please help.

Documanage Error #2002 (File Copy Error)

Hi,
I am getting this error "Documanage Error #2002 (File Copy Error)" during the Genarc process. I am not able to understand the problem. Can any one please let me know about this error.
Also is there documentation about documanage errors, please let me know.
Thanks in Advace

Turn on your debugging options in Documaker INI and see what you get.
< DBHandler:DMIA >
DEBUG = YES
< DBHandler:ODBC >
Debug = YES
Also you may want to turn up your logging in the poffice.ini and check those logs as well. It's been a while since I've seen that but if I recall correctly this error usually happens when you are trying to archive a transaction from Genarc to Documanage and either the connection is broken or the document category doesn't match.

Escaping file copy error?

I was copying a data CD which had a bad file. When I hit the bad file, the message appeared "The Finder cannot complete the operation because some data in "the source file" could not be read or writte. (Error code -36)".
When I click okay, the Copy message box remains, and clicking the X in that box to stop copying had no effect. I had to restart finder to escape. This is OS 10.5.4 on 2 x 2.66 GHz Dual-Core Intel Xeon Mac Pro. Thanks for any ideas. I couldn't find a bug report location in Apple Support.

Thanks for the suggestion, but there are no permission errors on the target disk or the system disk. The problem file is on a CD, and there's no way to repair permissions on a CD.
I think it's an OS bug that the copy dialog box won't cancel on a bad file copy error.

Need help with 875P Neo-FIS2R!! No on board lan??

Hey i just got the 875P Neo-FIS2R, it came with bios 1.2 on it.
At that point I got everything working nice, INcluding the onboard lan card. I then went to live update bios to 1.6 through windows and I had no problems, but after I restarted my comp. it came back on with out detecting the onboard lan?? It was detected before,but ever since I updated to bios 1.6, it doesn't dectect the lan anymore!!! Anything I can do??

It could be something simple. Did you check to see if the onboard LAN is Enabled in the Bios?
I'd check that first!

Can MSI add DOT to 875P Neo-FIS2R

Hi! Those guys here!
Will DOT be added to the 875P Neo-FIS2R in the next bios???
I'm using the BIOS1.6 but I still couldn't find DOT!
I hope it will be in BIOS1.7.
I LOVE MSI that's why I bought my board!
My Computer's Configuration:
P4 2.4C+875P Neo-FIS2R+GEIL DDR400 512MB+Winfast A310 Ultra
THANKS :D :D :D

There are some threads stating that it's already in the Beta 1.74 BIOS but requires a specific version of CoreCell (which is indicated by a DOT sticker on the board/box)
There was also another thread saying that aside from this, it seems to depend on the processor installed - which I find puzzling ?(

875P Neo-FIS2R File Copy errors loading Win XP Pro

Similar Messages

Maybe you are looking for