877 as Access Point

Hi all,
i've got a 877w and i need to configure it only as a access point.Can i trunk the 877 wich my lan and pass vlans from my lan to the 877 and associate one ssid to each vlan?
IOS Version:
C870 Software (C870-ADVSECURITYK9-M), Version 12.4(4)T8.
thanks

Perform these steps to configure integrated routing and bridging on VLANs, beginning in global configuration mode:
1 ) bridge [number | crb | irb |mac-address-table]
2) interface name number
3) bridge-group number
4) bridge-group number parameter
5) interface name numbe
6) bridge number route protocol
7) ip address address mask
For the further description for the configuration following URL may help you ;
http://www.cisco.com/en/US/docs/routers/access/800/850/software/configuration/guide/wireless.html#wp999748

Similar Messages

Cisco 877 as access point and DSL router - 2 subnets

I have been using an 877 to provide DSL access and wireless access point from two separate wired subnets. The idea is that traffic from one subnet will be routed to the DSL connection. The other subnet provides a bridged connection to wireless clients. Both subnets being isolated from each other. In the former case the router acts as DHCP server, whilst in the latter case a separate DHCP server is used. Despite all apparently working, recent introduction of a wireless client did not work and seemed to be acquring a DHCP lease from the router rather than the external DHCP server. It seems that broadcast traffic from the router DHCP server was traversing to the wrong interfaces, despite (I hope) only the wireless and the second wired subnet being in the bridge group.
I would be grateful if anyone can throw any light on this, the salient parts of my config are enclosed below. I have anonymised the public addreses using q1.q2.q3 therein. Many thanks.
dot11 ssid MYSSID
   authentication open eap eap_methods
   authentication network-eap eap_methods
   authentication key-management wpa
   guest-mode
no ip source-route
ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.10.10.1
ip dhcp excluded-address q1.q2.q3.15 q1.q2.q3.254
ip dhcp excluded-address q1.q2.q3.1 q1.q2.q3.8
ip dhcp pool sdm-pool1
   import all
   network q1.q2.q3.0 255.255.255.0
   domain-name MyDomain
   dns-server x.y.z.1 x.y.z.2
   default-router q1.q2.q3.3
bridge irb
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
switchport access vlan 10
spanning-tree portfast
interface FastEthernet3
switchport access vlan 10
spanning-tree portfast
interface Dot11Radio0
no ip address
encryption mode ciphers tkip
ssid mySSID
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
bridge-group 10
bridge-group 10 subscriber-loop-control
bridge-group 10 spanning-disabled
bridge-group 10 block-unknown-source
no bridge-group 10 source-learning
no bridge-group 10 unicast-flooding
interface Vlan1
description $ES_LAN$
ip address q1.q2.q3.3 255.255.255.0
ip access-group 102 in
ip nat inside
ip virtual-reassembly
interface Vlan10
no ip address
bridge-group 10
interface BVI10
ip address 192.168.253.251 255.255.255.0
bridge 10 protocol ieee
bridge 10 route ip

If the Router is not the DHCP server, you'll want to put an ip helper-address under teh BVI 10 and point to the correct DHCP server
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered

Wireless access point advice for SMB (5 users)

I have a small site, 12 employees, five of whom will need wireless access to the LAN.
This site has an 877 (not 877W) and so I need a wireless access point.
I've been looking at the Cisco Aironet 1130AG. Can anyone make a recommendation, something that will be the same or similar to configure as wireless services on the 800 series wireless routers.
There is no domain or radius server, so any user authentication will need to be handled by the AP.
Any useful information would be much appreciated.
Thanks
Gareth

You're on the right track. The 1131AG is a great platform for small offices. It has built in antennas and is not offensive looking when mounted to the ceiling. Running a single 1131AG would allow you to run RADIUS locally on the AP so you could still use EAP security types such as EAP-FAST with WPA2.
Once you go to deploy, there are plenty of us here on the forum that can help if you run into config gotchas.
Of course I'll include the standard disclaimer that your coverage might vary based on the building construction, so you could need multiple APs to cover enough area. If certain coverage is absolutely mandatory, you should consider a site-survey beforehand.
-Eric

Unable to stop the event logs on access point console

Hi team,
I have an AIR-LAP1131AG-E-K9 access point having ios c1130-k9w8-mx.124-21a.JHB1.
When I am trying to take the console of it there are many logs generated like LWAPP ...Go join the controller, Discover controller etc. and the ap is unable to register to the controller(2112 with ios version 6.0.199.4). I'm trying to enter the command but there are many event msg generated....How do i stop this event log. I tried entering the command no debug all. but still there are many logs...
I want to enter the the following commands
#lwapp ap ip address <ip addr>.
#lwapp a pip default-gateway <gateway ip addr>
#lwapp ap controller ip addr <controller ip>
#wr me
Revert me back on urgent basis
Thanks in advance..

Thanks Rashika,
Now the access point got registered to the controller..This happened becuse of country Code..
I have changed the country code to UK, Belgium it started working fine.
Initially when it was IN the access point was not getting register..
But now the problem which arised is that the user is unable to get authenticated to the radius server.
Radius server is reachable and we have done every changes required for radius server authentication.
Users are getting rejected.
Customer is saying that the radius server is in IN domain and the WLC/access point is in UK,BE and hence the users are unable to connect..
Is it so??
Rply
Thanks in advance...

How do I make my AirPort Extreme a access point?

I just bought a Time Capsule and now I want to extend my range of my network. How do I make my AE an access point?

In this case, you will want to configure both base stations in an extended network.
Dynamic WDS - Extending a Wireless Network Setup
If practical, place the base stations in near proximity to each other during the setup phase. Once done, move them to their desired locations.
Open AirPort Utility, and then, select the base station that will connect to the Internet.
Choose Manual Setup from the Base Station menu, or double-click the base station to open the configuration in a separate window. Enter the base station password if necessary.
Click AirPort in the toolbar, and then, click Wireless.
Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then, select the “Allow this network to be extended” checkbox.
Next, select the base station that will extend this network, and then, choose Manual Setup from the Base Station menu, or double-click the base station to open its configuration in a separate window. Enter the base station password if necessary.
Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then, choose the network you want to extend from the Network Name pop-up menu.
Enter the base station network and base station password if necessary.
Click Update to update the base station with new network settings.
(ref: Pages 43-44 of Apple AirPort Networks.)

How do I configure my AirPort Extreme as a wireless access point? My cable modem goes to a router, and one of those ports goes to my AirPortExtreme.

I am about to hook up my airport extreme. My cable modem goes into a router, and one of those ports will supply my airport extreme. I was told by the Apple Store that I would need to configure my airport extreme as a wirreless access point. How do I do this?

With sbcgobal I got a Gateway 2wire modem. What I would like to know is how do I set up my APE as remote?
Unfortunately, you won't be able to do this as few non-AirPort routers will work with AirPorts in a Wireless Distribution System (WDS).

Can't HP Officejet pro 8100 do wifi access point?

Yesterday my HP Officejet pro 8100 arrived and I try to connect via wifi. I thinked that It need a infrastructure access point to print via wifi.
When I powered on the printer I osserved that It create an access point autonomously with SSID: HP-Setup-7A-Officejet Pro, with IPv4 address server, etc...
I was very happy and I printed a page with my smartphone samsung s4 connected directly with printer access point (not wifi direct but standard wifi).
Today no changed occurred but I can't use printer with its own access point, but only with an external wifi access point.
Someone can help me, please? It could be an hardware problem?
Thanks,
Luca
P.S. in web server I checked that "access point connectivity" (Punto di accesso wireless connettività in Italian) is checked.
This question was solved.
View Solution.

Hello lucait
To print via WiFi you need to have a wireless router setup. Once you have the wireless router setup correctly you will have a SSID and Wepkey that will enable you to add devices to your network. The network will allow all your devices to communicate not just with each other but with the internet. At the moment your printer was not put in a network so instead of broadcasting on a network it is broadcasting on it's own network called HP-Setup-7A-Officejet Pro which is only good for a short period of time to allow you to setup your wireless. I am going to assume you have a wireless network and you are just needing assistance getting the printer setup on that network.
To set your printer up on a network you will need to reset your network defaults so your printer begins to broadcast that HP-Setup-7A-Officejet Pro network again. You can do this buy following the steps on the HP Support document Resetting the Network Settings. Once you have done this you can begin to install the software that came with your printer on your computer. You want to set the printer up wirelessly when the option arrives. The software should configure your printers wireless for you and put it on the network. Once completed you should be able to access your printer from all your devices as long as they are on the network.
I hope this helps resolve your wireless issue. Thank you for posting on the HP Forums. Have a great day!
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
Dunidar
I work on behalf of HP
Find out a bit more about me by checking out my profile!
"Customers don’t expect you to be perfect. They do expect you to fix things when they go wrong." ~ Donald Porter

Setting up a netgear n300 as wireless bridge/access point with airport extremee

I just replaced my netgear wireless router with the airport to allow our many devices on the network without knocking each other off and also increase the speed. But would like to use the netgear as a wireless bridge or access point so that I can still connect my NTFS formatted hard drive to be shared on the network. Any suggestions would be appreciated. I can not seem to find my netgear router with 192.168.1.1 as that comes up with another device. I have tried doing this with a windows laptop in another room but can not seem to make it work. I am now hooked up directly to the airport thinking i need to do it that way and still no luck. Please help.

As long as you intend to do this over ethernet it will work.. you cannot easily wireless repeat or bridge to an apple router.. you would need specific hardware to do it.
What is the exact model of netgear you have?
The setup method depends on the functionality of the router.. but lets assume it does not have a bridge or WAP mode.
You use WAN bypass.
1. Setup the Netgear with IP address in the correct IP range for the rest of the network.. it is hard to talk generalities so lets say the apple is main router and your network is now 10.0.1.x .. then set the Netgear to 10.0.1.250 (apple uses IP 2-200 by default) you can use any value you like outside the DHCP range. Up to the limit which is 254 as long as you keep track of all static IP devices. Apply this setting and power cycle the router.. and you might need to power cycle the computer as well to pick up the new IP.
2. Turn off the DHCP server in the Netgear. You may lose connection to the netgear now.. do not worry about it.. (this can be combined with one.. if you firstly turn off dhcp before you change the IP.. but whatever is possible.. at some point you will need to change around and if you forget what IP .. you will be in a mess.. so write it on a label and stick on the base of the router.. also without dhcp you will either need to reset router to factory using reset button or use static ip on the computer. )
3. Plug ethernet from LAN of the main router to LAN of the Netgear. Reboot the whole network is often necessary.
4. In your computer plugged somewhere in the network.. open browser and go to the address you set.. 10.0.1.250 in my example.
5. You can then setup the Netgear to do whatever you like.. DIsk access is fine.. wireless is fine.. it just cannot be a router.
Many many reboots if you get lost. Hit reset and start over.

New wireless network with several access points

Hi,
We are planing to deploy a wireless network that will cover two floors consisting of about 5 or 6 Access points. It should have 2 or 3 SSID (placing the clients in 2 or 3 different VLANS).
What would be the best solution for this?
I read a lot about wireless controllers. What about an option to just buy standalone access points? Are they all configured to work with the same SSID's and on the same channel?

A centralized controller should make your life easier:
- Centralized config - set up everything on the controller and it gets applied to the AP's.
- Centralized monitoring - when someone has a problem, you can check the controller instead of having to figure out the AP to which they are connecting (computers don't always connect to the closest AP)
- Dumb AP's - if someone steals one of your APs, they will not be able to learn much about your network from a lightweight AP
- Radio Resource Management - let the controller make the channel and power setting decisions for you
- If you use PoE, you may never have to get on a ladder and use the console port of a lightweight AP. The AP is managed by the controller, and for the rare occasion that you can't get an AP to respond - just cycle the power to the AP via the switch port.
There are some downsides:
- Cost of the controller (since you're buying AP's one way or the other)
- Most cost: If your wireless network is important, then you typically want a second wireless controller as a backup
- Probably more downsides, but my brain hurts today

When using EA6400 as an access point only, certain features lost

I've set up my EA6400 and have it connected to my Verizon MW424WR(Gigabit) and it works fine as an access point and the Twonky Server uses the USB drive I have attached to the router's USB port. Problems:
1)I can not use the linksyssmartwifi link for management, I have to use the IP(set for 192.168.1.50) for this. When trying to register/login, the Linksys end is trying to find a Linksys router but can not and will not allow any action.
2)Although Twonky will use the attached HD, I can not share the device over the home (Windows) network. I've tried various incantations of the IP \\192.168.1.50\(whatever share name I can think of) with no avail.
3)Using the Linksys admin, the Device List is incomplete. Devices connected wirelessly such as my iPod, Roku, Sony Media Player and WD HD TV Live do not show as wirelessly connected and do not have an IP listed.
4)Is there any point in using the Media Prioritization settings since no routing is done by an access point. Or will it actually prioritize the wireless connection.
BTW, the Verizon router can not be set in bridge mode so I have to use the router as an access point to accomplish what I wish.
TIA,
Randy

Some applications and router features require the use of the WAN port. If the router is set up for LAN to LAN AP mode only, then those features won't work in this mode. Only Router mode.
If the ISP modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems: Link>http://www.practicallynetworked.com/networking/fixing_double_nat.htm and http://computer.howstuffworks.com/nat.htm If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ. Then connect the router in router mode using the WAN port to the ISP modem, then features and apps should work.
tduong44 wrote:
I am having the same problem, not being able to use ANY apps like USB drive, FTP, etc when setting the device in bridge mode because I want to access the drive outside of my network using port forwarding. Contact Linksys/Cisco support and was told that I needed to setup the Verizon router in Bridge mode.. That was it, that was the solution... AND also to check with provider for instruction how to.. WTH kind of support is that>??

An Error Occurred while trying to join "my wireless access point"

Hi,
I've been using wireless access for a year and never had a problem connecting.
But starting yesterday I get a +*An Error Occurred while trying to join "my wireless access point", Please try again.+* Message.
I have 2 Mac's and have no problem connecting with the other one. It’s just the IMac.
I tried everything including resetting router, changing password, adding a $ to the password, accessing without password, deleting the whole air port and create a new one, but still getting the same message.
I might need to add, while I was working with the IMac I didn’t use wireless for a few hours, but when I got back to my browser I noticed that I was connected to a different wireless service. (FONFREEINTERNET if it matters) I have no idea why, since I didn’t change it.
Anyways, I tried to switch back to my access point, but it wouldn’t let me. It’ll just give me the +*An Error Occurred while trying to join "my wireless access point", Please try again.+* Message.
Funny is when I use the FONFREEINTERNET access point the internet seems to work fine.
I could look up Google without a problem, but when I tried to connect to Facebook for example it won’t let me. Instead a FONFREEINTERNET page will pop up with some options on how to pay! (by minute/or day/or week…)
I get the strange feeling that they planted some kind of bug/virus!!!
I don’t know what else to do.
Anyone knows that problem? What can I do?
Any help is greatly appreciated!
I researched on FONFREEINTERNET, there’s a spot close to my house/guess that’s the one I used…
http://maps.fon.com/ ZIP CODE 904-0113 and you’ll see a coffee pod, which is about 2 minutes walk from my house.

Hello Tesserax,
I get the same error message again...
I tried the 3 suggested steps again, but unfortunately it did not work.
After a Restart, Sleep or just the awaking from Screensaver mode I’m disconnected from my wireless Network anymore.
Even if the Computer was asleep for just a second!
I am able to fix the problem temporarily with Network Preferences → Assist me → Diagnostics
Choose Airport → Choose network → Enter Password (Even if I check safe password it’ll ask me every time) → and than usually all lights on the left menu switch from red to green and I get the popup message “A Network Change has been detected. Your Internet seems to work fine.” (similar - I’m at work and don’t remember exactly)
And it works fine…until the screensaver comes on or it sleeps again
I have the Problem with my IMac and Mini but the IMac at least remembers my password…
Any Ideas
I’m connected through a Buffalo WZR2-G300N wireless router

How to use Home Hub 3 as a 2nd router(access point...

Hi guys hope you can help; I am trying to add my Home Hub 3 as a 2nd router (ie an access point) to my home network and struggling.
What am I trying to achieve.
I have a fully functioning home network which is working great but the wireless range does not extend to the room above my garage, some distance away from the main house. I currently service it with an Ethernet link from my E4200 router, via the mains wiring, to link to a PS3 there. But I want to extend this to have a wireless network in the remote room so I can link multiple devices - rather than spend more money, deploying a 2nd router which I already have is preferable.
What have I got.
I have a Linksys E4200 router (nice piece of kit) attached to my ADSL line via a Belkin N1 wireless modem-router set to “modem only” mode (I was using a DSL modem until yesterday but that went AWOL and digging out the Belkin router I saw that it had a modem only function – and it/they worked first time )
All of my gear in the house is attached wirelessly to the E4200 which is delivering circa 11.5mbps from a maximum of 12.5mbps for the line measured by BT onsite. So all is fine there.
What have I done to try and use the HH3
Linked an Ethernet cable between one of the Ethernet ports on the E4200 to a mains plug.
Linked an Ethernet cable from a mains plug to one of the Ethernet ports on the HH3 router.
Ie as the PS3 was linked.
3. Switched on the HH3 router: the power light is solid blue, the wireless light is solid blue, the broadband light is off
4. Connected my laptop to the HH3 network and loading up a web page on IE9 displays a web page from bthomehub.home/etc etc with title BT Home Hub and a message “Can’t connect to Broadband”. It is the start of a self- diagnostic routine. Answering all the questions I eventually get a Home Hub Administrative Home Page displayed.
Is there a quicker way of getting to this admin page??
5. I switched off DHCP
I changed the IP address from 192.168.1.254 to 192.168.1.200 as this seems to be what the other threads on this subject did.
When I went to apply the change a message came up telling me that I might not be able to access the HH3. I ploughed on disregarding this and needless to say I could not then access the HH3 via the web interface and trying to access a web site nothing happened.
6. I did a hardware reset on the HH3
7. Going through the motions again, when I got to the admin pages again, I switched off DHCP and this time left the IP address alone, ie 192.168.1.254.
When I went to apply this I got the message
“After changing these settings you will need to renew the IP address of all devices connecting to your BT Home Hub. Please follow the instructions provided with your devices.”
I applied the change – but have not yet done any fooling around with IP addresses on my laptop because I don’t want to start mucking around with my laptop
I then tried to access a website, and failed, but on this occasion rather than nothing happening, the Home Hub website came up again displaying the error message page.
And that is where I stand. All looks so easy when reading other threads on this and other forums but it is not working for me.
Any help greatly appreciated.
The IP settings on the E4200 are
IP 192.168.1.1
Range 192.168.1.100 to 192.168.1.149
Also connection type on the E4200 is POE not POA – as far as I recall that is what it needed to be to connect to the DSL modem and work.

Thanks for the speedy reply!
I have actually came across this page before - I seem to hit a snag when I connect the repeater hub (my HH3). As outlined, I have at all times kept the repeater hub connected via ehternet into one of the regular LAN ports to my main HH5.
But when I connect my laptop to the repeat hub (HH3), I am actually connected to the internet somehow (I assuem using the HH5 network) but under my network connections it says I am connected to the HH3. As a result, when I go to the homehub settings page 192.168.1.254, it brings me to the main HH5 settings page and not the repeater HH3.
According to the instructions it says I should "Ignore the not connected page", but I am connected and I cant seem to alter any of the settings on my HH3 while it is connected to the HH5.
Any other pointers?
Thanks!

What is the WPS button on my access point? I am trying to setup wirelessly with a canon MX892 printer

Printer setup instructions say to press the WPS button on the access point (my 4th gen Time Capsule). Does that mean hit reset and will I have to setup every other device again by doing that?

No, do not hit reset .. it is not a WPS button.
Apple products do not use WPS, so no WPS button is needed. And they have no need to implement one.. nothing exists outside the Apple bubble.. didn't you know that??
Read the forum expert Tesserax instructions for using WPS. https://discussions.apple.com/message/16034147#16034147
But it is better to plug in your printer to a mac by usb and use the disk provided to do a full manual setup of wireless.. WPS is simply the easy way.

Can a single Access Point support both bridge mode and Access Point mode at the same time

Hi Guys
Does anyone know which access point can work in both bridge mode and AP mode ?
Cheers

Well what are you trying to cover. If its really a large outdoor area, then look at the mesh AP. Those require a WLC. Autonomous or stand alone ap can perform bridging on one radio and client access on another. You can also look at AP that support indoor mesh that also controlled by a wlc. If your putting APs outdoors, then look at the outdoor mesh.
Thanks,
Scott Fella
Sent from my iPhone

Prompt never appears in a 2602i access point

Hello:
Today I converted an AIR-CAP2602I-A-K9 access point to autonomous using the mode button/tftp method, but no matter what IOS I install (I tried 2 different IOS and also tried entering to Rommon - I am able to change IOS because the procedure I used does not need any command), i never get to see the prompt so that I can introduce commands to configure the AP. It's like it hangs after "succesfully" initializing
The only thing I can see all the time are "normal" console messages, and It shows no error message at all. It happened even before the downgrade.
This is where the AP stops, but it is not really hung because console messages could keep showing up. It just never gets to the promt so I can enter some commands. Would not even acept Enter.
Cisco IOS Software, C2600 Software (AP3G2-K9W7-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 30-Jul-13 23:12 by prod_rel_team
Initializing flashfs...
flashfs[3]: 200 files, 7 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 31739904
flashfs[3]: Bytes used: 14286848
flashfs[3]: Bytes available: 17453056
flashfs[3]: flashfs fsck took 9 seconds.
flashfs[3]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 11999232
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 11998208
flashfs[4]: flashfs fsck took 0 seconds.
flashfs[4]: Initialization complete.
Copying radio files from flash: to ram:
Copy in progress...CCCCC
Copy in progress...CCC
Copy in progress...CCCC
Copy in progress...CCCC
Copy in progress...CC
Uncompressing radio files...
...done Initializing flashfs.
Radio0 present 8764 8000 0 A8000000 A8010000 0
Rate table has 244 entries (64 SGI/104 BF variants)
Radio1 present 8764 8000 0 88000000 88010000 4
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-SAP2602I-A-K9 (PowerPC) processor (revision A0) with 180214K/81920K bytes of memory.
Processor board ID FGL1716S0Q6
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: BC:16:65:95:A7:C3
Part Number                          : 73-14588-02
PCA Assembly Number                  : 800-37899-01
PCA Revision Number                  : A0
PCB Serial Number                    : FOC17151DSW
Top Assembly Part Number             : 800-38356-01
Top Assembly Serial Number           : FGL1716S0Q6
Top Revision Number                  : A0
Product/Model Number                 : AIR-CAP2602I-A-K9
Press RETURN to get started!
*Mar 1 00:00:11.819: %IFMGR-7-NO_IFINDEX_FILE: Unable to open nvram:/ifIndex-table No such file or directory
*Mar 1 00:00:11.935: FIPS IOS test Image Checksum successful
*Mar 1 00:00:11.935: FIPS IOS test Crypto RNG DEK Key Test successful
*Mar 1 00:00:11.939: FIPS IOS test SHA-1 successful
*Mar 1 00:00:11.939: FIPS IOS test HMAC-SHA1 successful
*Mar 1 00:00:11.939: FIPS IOS test AES CBC 128-bit Encrypt successful
*Mar 1 00:00:11.939: FIPS IOS test AES CBC 128-bit Decrypt successful
*Mar 1 00:00:11.939: FIPS IOS test IOS AES CMAC Encrypt successful
*Mar 1 00:00:11.939: FIPS IOS test IOS CCM Encrypt successful
*Mar 1 00:00:11.939: FIPS IOS test IOS CCM Decrypt successful
*Mar 1 00:00:11.939: FIPS IOS test RSA Signature Generation successful
*Mar 1 00:00:11.939: FIPS IOS test RSA Signature Verification successful
*Mar 1 00:00:11.939: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:18.863: FIPS RADIO test AES 128-bit encrypt for TX on Dot11Radio 0 successful
*Mar 1 00:00:18.863: FIPS RADIO test AES 128-bit CCM encrypt on Dot11Radio 0 successful
*Mar 1 00:00:18.863: FIPS RADIO test AES 128-bit CCM decrypt on Dot11Radio 0 successful
*Mar 1 00:00:18.863: FIPS RADIO test AMAC AES 128-bit CMAC encrypt on Dot11Radio 0 successful
*Mar 1 00:00:18.863: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:24.991: FIPS RADIO test AES 128-bit encrypt for TX on Dot11Radio 1 successful
*Mar 1 00:00:24.991: FIPS RADIO test AES 128-bit CCM encrypt on Dot11Radio 1 successful
*Mar 1 00:00:24.991: FIPS RADIO test AES 128-bit CCM decrypt on Dot11Radio 1 successful
*Mar 1 00:00:24.991: FIPS RADIO test AMAC AES 128-bit CMAC encrypt on Dot11Radio 1 successful
*Mar 1 00:00:24.991: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:25.007: initializing dot11 onplus
*Mar 1 00:00:25.259: not a autoconfig enabled device!!!
*Mar 1 00:00:27.039: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:28.039: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 00:01:13.383: Starting Ethernet promiscuous mode
*Apr 12 07:12:42.000: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Apr 12 07:12:42.000: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Apr 12 07:12:42.003: %CDP_PD-4-POWER_OK: Full power - AC_ADAPTOR inline power source
*Apr 12 07:12:42.011: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2600 Software (AP3G2-K9W7-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Tue 30-Jul-13 23:12 by prod_rel_team
*Apr 12 07:12:42.011: %SNMP-5-COLDSTART: SNMP agent on host ap is undergoing a cold start
*Apr 12 07:12:42.991: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Apr 12 07:12:42.999: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Apr 12 07:12:42.999: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Apr 12 07:12:44.651: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed
*Apr 12 07:12:44.651: DPAA Initialization Complete
*Apr 12 07:12:44.651: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Apr 12 07:12:44.971: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up <--- CURSOR STOPS HERE AND WON'T ACCEPT ENTER OR ANY OTHER KEYBOARD ACTION
Any thoughts?
Best regards and thanks in advance

Leo, I'm usign SecureCrt, so I disabled XON/XOFF and DTR/DSR as usual, but was not disabling RTS/CTS, so I did and now it is working. Thank you very much!

877 as Access Point

Similar Messages

Maybe you are looking for