881 Router Wireless Module

Hi Everyone,
I was given an 881 router to work on. I was told that it has the integrated wireless module installed, but I cannot see any radio antenna on the device. Is there a command I can run to determine if the wireless module is installed. I tried sh ver and it did not reveal any information to suggest there is a wireless module.
Also in global configuration mode, the command interface Wlan-ap0, is not accepted.
Any help is appreciated. Thanks.

880W antenna is fixed. You can't remove or replace it. So if there's no antenna then it doesn't have one.
The command "sh inventory" that Michael has posted is a pretty good indication as to the exact model of the router you've got. "sh version | b License UDI" command will also help.

Similar Messages

Wireless Module Not Supported...in the manual it is?

HP maual located here: http://h10032.www1.hp.com/ctg/Manual/c02770268.pdf
Page 20 Chapter 3 it lists:
Intel Centrino® Wireless-N 1000 (802.11b/g/n) 593530-001
So I ordered this from the HP parts store and received it today and the laptop posts with a Wireless Module Not Supported. WLAN Module ID 702 message.
So how do I proceed from here? Laptop came with an ralink card that only connected at 72Mbps, the atheros AR9285 constantly connects at 65Mbps unless I reset my router every time I connect.
My laptop is a HP Pavilion g6-1a40ca
Help please!
Marc

Thanks for replying
Looks like modding the bios is the only way I'll get something better into this laptop. All I know is that the two officially supported cards I have right here are terribly slow/flaky. Going by the manual I really don't have any other choice in wireless cards. This is a great laptop for the price, just wish it didn't come crippled.
Oh I know...lol...I'll buy a usb one and soldier it onto one of the usb ports internally. j/k
Thanks again for clarifying for me. If anyone has anything additional to add to this thread in future about adding support official or unofficial, please post it here.
Thanks,
Marc

Wireless module different IP addresses

hello I have a problem with my wireless router, cisco wireless module allows you to give different IP addresses so that IP addresses are different who can help me please

First you want a merry Christmas and a happy new year 2011 and to wish good health especially
no, it now works as a computer directly connected to the cable it does not get internal ip address of dhcp server wireless, nor how to solve that problem?
mvg

Using WRT610N w/ Intel WiFi Link 5100 wireless module

I am considering buying an FW or Z series Sony laptop which includes Intel WiFi Link 5100 as the wireless module, which is a dual range (2.4 & 5 GHz) 802.11 a/b/g/draft-n module. In order to benefit from wireless-n speeds as much as possible, I want to buy a good Wireless-N router. The one I am considering buying is Linksys WRT-610N. However, the thing is that I see on some forums that people have some problems with an older Linksys Wireless-N router used in conjunction with an older Intel wireless module. I am afraid I can have similar problem with the combination of the above mentioned router and wireless module. Moreover, I read a comment on somebody’s review of WRT610N on amazon.com that says that WRT610N is based on broadcom wireless chipset and thus may not give a good performance on PCs having an Atheros wireless module. If this is correct, it may go the same for using WRT610N with an Intel wireless chipset. Anyhow, my question is, have you been using a Linksys router with your PC that has an Intel wireless module and how do you find the performance (speed, range, frequency of drop-offs)? Comments from people using WRT610N (at least WRT600) along with a PC that has an Intel WiFi Link 5100 will be much more appreciated!

I think your in luck.. I have the exact combination that you are considering. I have a Sony FW190 with the intel 5100 a/g/draft-n card.
In my network I have the following:
1 Toshiba laptop 802.11abg (atheros)
1 Sony laptop 802.11abg (intel)
1 Sony FW190 802.11agn (Intel 5100)
I'm leveraging the dual radios on the wrt610n using 5Ghz band (wide) exclusively for the Sony FW190 the other laptops use the 2.4Ghz band.
On the Draft-N wifi connections I get connection speeds from 136Mbps to 300Mbps .. I've gotten donload speeds from my home server at a sustained 60Mbps+ speeds.
The configuration on both the laptop and the router took some understanding because of the features that 802.11n provides and the capability of the router to support dual radios. But overall I'm happy with the hardware and performance.
Good luck!

Wireless module on 800 series reboot

I have a wireless problem on the 800 series and with two PCs connected to the wireless router and you're a 40GB file to send by second PC over the wireless module does away is this normal?

You can get the PoE daughter card pre-fitted before the appliance leaves the factory or you can do it yourself as an after-sales item.
800-IL-PM-4 is the daughter card. Read the Q & A below:
Q. Can the PoE be upgraded after ordering?
A. Yes, you can upgrade the PoE on all models except the C892FSP-K9, which does not support PoE at all. For all Cisco 890 Routers, the product ID (PID) for the PoE upgrade is 800-IL-PM-4=. This PID comes with two power supply options: 80 or 125 watts. The older CISCO890 requires the 80-watt option, whereas the newer C890 requires the 125-watt option.
Q. Why do some routers use 80 watts and others 125 watts for PoE?
A. The 80-watt power supply is used in addition to the standard 60-watt power supply, so you will have two power supplies connected to the router. For the newer routers we combined these two power supplies into the one 125-watt power supply (hence we have a 4-pin connector). Both models support the base router as well as 4 ports with standard PoE.

Cannot connect IBM Thinkpad to Linksys Router Wirelessly

I recently moved in with a friend, and my IBM Thinkpad T42, with Windows XP, cannot connect to her Linksys WRT120N router wirelessly. I am able to connect to the internet using an Ethernet cable, and I am able to connect to other public wireless networks.
I have been told by Cisco helpdesk people that it is because Windows XP does not support WPA2 security, and/or that because they don't know much about IBM computers, I should get rid of the third party internet connection software, IBM Access Connections, that came with my computer.
I have been having this problem for a week, and I did not even know I had IBM Access Connections until today, so I don't think that's the problem. Also, my friend has been using that application successfully on her computer, Thinkpad T61, Windows XP, to connect to this router, which she has been using for 2 years. So with two almost identical computers, does anybody know why my wireless connection isn't working?

Answer these questions, I may be able to give you the right solution to your issue:
1. Go to your Network Connections folder on your wired computer and check which one is connected:
a. Local Area Connection
b. Broadband Connection
c. 1394 Connection
2. What is the IP address of your computer?
3. Who is your internet service provider?
4. What is the error message when you connect the wireless computer to the network?

Wireless module not working(701)

Hello, i recently formatted my laptop and then i found that at startup my laptop is saying Wireless module not found(701)
It says it may be not installed correctly or not functioning.
So i disassembled my laptop to see any connection problem and tried connecting with changing positions of wires with card but still not working!
I Googled for drivers but didnt geta any!
here is detail about Wlan + Bt card
AzureWave AW-NB041H
IEEE 802.11 b/g/n + 802.15 BT combo card
Model No.-RT3090BC4
FCC ID- VQF-RT3090BC4
IC-7542A-RT3090BC4
India-448/2010/WRLO
CMIIT ID- 2010DJ0636
Please help to me to solve this problem!
This question was solved.
View Solution.

It needs to be replaced. This one will work in your netbook. It will pass the whitelist BIOS check and provides wifi and Bluetooth:
http://www.ebay.in/itm/HP-WI-FI-BLUETOOTH-COMBO-CARD-BCM94313HMGB-600370-001-598711-001-G6-CQ42-/321...
If this is "the Answer" please click "Accept as Solution" to help others find it.

Connect 2 Router wireless

I have 2 WRT54G router, router#1 in the kitchen with modem and internet work perfectly. router#2 is in my home office without moden and no internet.
how can i connect this 2 router wireless?

Not at all. The WRT is a wireless router not an access point. The WRT does not support wireless bridging with Linksys firmware.
Option 1: Get a 3rd party firmware which allows wireless bridging on a WRT.
Option 2: Get an access point like the Linksys WAPs which are capable of wireless bridging.

Wireless module not supported

I have a DV6Z-6C00 CTO laptop notbook and I recently had to install a new wireless card but I keep getting a Wireless module not supported error. I checked with the manual and I ordered a Intel Centrino-N 1000 WLAN Module (593530-001 replacement #) and I checked on the actual card (and they match). So why am I getting this error, and how can I fix it?
Btw I have Windows 8

Is the wireless card an actual HP card? It is not enough that it be the same Intel chipset card.

Connect to WRT400N Router Wirelessly from Another Switch/Router?

My cable line, modem, and WRT400N router is in the basement and wired via cat5 to several other rooms in the house. The signal strength is great everywhere. Unfortunately, wiring was not run to the room where I need to connect (2) desktop PC's to the Internet. Can I use another router or switch to connect to the WRT400N router wirelessly so that those PC's will have Internet access via that device connection, or will I need to put wireless adapters in each machine that talk to the router in the basement directly?

Two linksys router will not communicate wirelessly...You can connect the switch/router hardwired to the router.

QoS 881 router not policing

Hi,
I'm trying to setup QoS policing to limit bandwith for some protocols. I'm using a 881 router.
I just want to police the traffic for the protocols and configured this:
class-map filetransfer
match protocol itunes
match protocol bittorrent
match protocol ftp
policy-map qos_filetransfer
class filetransfer
police 100000
   conform-action transmit
    exceed-action drop
int f4
service-policy input qos_filetransfer
service-policy output qos_filetransfer
But when I'm testing to download a file with ftp the traffic is not limited.
If I run: sh ip nbar protocol-discovery stats bit-rate top-n 10, I can see the ftp traffic:
FastEthernet4
Last clearing of "show ip nbar protocol-discovery" counters 00:05:03
                            Input                    Output
   Protocol                 5min Bit Rate (bps)      5min Bit Rate (bps)
   ftp                      3340000                  104000
   stun-nat                 14000                    97000
   ipsec                    1000                     1000
   icmp                     0                        1000
   isakmp                   0                        0
   dns                      0                        0
   skype                    0                        0
   unknown                  0                        1000
   Total                    3355000                  204000
If i run: sh policy-map interface f4
FastEthernet4
Service-policy input: qos_filetransfer
    Class-map: filetransfer (match-all)
      0 packets, 0 bytes
      5 minute offered rate 0000 bps, drop rate 0000 bps
      Match: protocol itunes
      Match: protocol bittorrent
      Match: protocol ftp
      police:
          cir 100000 bps, bc 3125 bytes
        conformed 0 packets, 0 bytes; actions:
          transmit
        exceeded 0 packets, 0 bytes; actions:
          drop
        conformed 0000 bps, exceeded 0000 bps
    Class-map: class-default (match-any)
      96296 packets, 139493940 bytes
      5 minute offered rate 3050000 bps, drop rate 0000 bps
      Match: any
Service-policy output: qos_filetransfer
    Class-map: filetransfer (match-all)
      0 packets, 0 bytes
      5 minute offered rate 0000 bps, drop rate 0000 bps
      Match: protocol itunes
      Match: protocol bittorrent
      Match: protocol ftp
      police:
          cir 100000 bps, bc 3125 bytes
        conformed 0 packets, 0 bytes; actions:
          transmit
        exceeded 0 packets, 0 bytes; actions:
          drop
        conformed 0000 bps, exceeded 0000 bps
    Class-map: class-default (match-any)
      59355 packets, 7299832 bytes
      5 minute offered rate 161000 bps, drop rate 0000 bps
      Match: any
Seems that the Class-map class-default are matching the packets, but I have not configured any class-defaults.
Please advice what to do.
Thanks

Hi,
Tested but can't get it to work.
I have tested:
class-map filetransfer
match protocol itunes
match protocol bittorrent
match protocol ftp
match any
and:
class-map match-all filetransfer
match protocol itunes
match protocol bittorrent
match protocol ftp
match any
and:
class-map match-any filetransfer
match protocol itunes
match protocol bittorrent
match protocol ftp
match any
I still get full bandwith when downloading a file with ftp from internet --> a computer on vlan1
Any more idea?
router#sh policy-map interface f4
FastEthernet4
Service-policy input: qos_filetransfer
    Class-map: filetransfer (match-all)
      0 packets, 0 bytes
      5 minute offered rate 0000 bps, drop rate 0000 bps
      Match: protocol itunes
      Match: protocol bittorrent
      Match: protocol ftp
      Match: any
      police:
          cir 100000 bps, bc 3125 bytes
        conformed 0 packets, 0 bytes; actions:
          transmit
        exceeded 0 packets, 0 bytes; actions:
          drop
        conformed 0000 bps, exceeded 0000 bps
    Class-map: class-default (match-any)
      260290 packets, 385289380 bytes
      5 minute offered rate 6399000 bps, drop rate 0000 bps
      Match: any
Service-policy output: qos_filetransfer
    Class-map: filetransfer (match-all)
      0 packets, 0 bytes
      5 minute offered rate 0000 bps, drop rate 0000 bps
      Match: protocol itunes
      Match: protocol bittorrent
      Match: protocol ftp
      Match: any
      police:
          cir 100000 bps, bc 3125 bytes
        conformed 0 packets, 0 bytes; actions:
          transmit
        exceeded 0 packets, 0 bytes; actions:
          drop
        conformed 0000 bps, exceeded 0000 bps
    Class-map: class-default (match-any)
      163215 packets, 16962903 bytes
      5 minute offered rate 283000 bps, drop rate 0000 bps
      Match: any

I can connect hardwired but my wireless laptop will not recognize my router wirelessly

I have the WRT54G and for a while my laptop was working with my router wirelessly. We then hooked 4 other computers into it. At that point my laptop could connect to my router wirelessly but i could not get on the internet. So i went to the website 192.168.1.1 and tryed to change the security settings. I reset the security settings and now I cannot get on that website anymore. My laptop doesn't see the wireless signal from the router but it does work hardwired. anyone have any ideas what i messed up??? oh and by the way i have vista
Message Edited by on 07-30-2007 02:36 PM

did you change the router settings from your wireless laptop ?? its always recommended to change the router settings from the wired computer ...
also , on the router web interface , try changing the wireless channel - either 1 or 11 , beacon interval - 50 , Fragmentation threshold - 2306 , RTS threshold - 2307

Can a Cisco 881 router create an L2TP/IPsec tunnel via NAT to Windows 2008?

Hi
Was anyone successfull in setting up an L2TP/IPsec tunnel through NAT-T against a Windows 2008/ R2 RRAS server? I am using an 881 router and the layout is someting like this:
Client -> 881 -> NAT -> internet -> Windows 2008 RRAS
The tunnel goes form the 881 to the Windows server (not from the client...).
Thanks
Roland

Hi Federico
Thanks for your help! Much appreciated.
In my case this should be transparent to the client - I would like not to initiate the connection from the client.
Does that makes sense? I am considering L2TP because Windows 2008 R2 doesn't support IPSec tunnels through NAT (2008 R2 being the responder and the Cisco router the initiator of the IPSec connection).
Regards
Roland

Can i transfer files from my galaxy note 3 to my apple airport router wirelessly?

Can i transfer files from my galaxy note 3 to my apple airport router wirelessly?

It should work.. remember all smb compatible names.. short no spaces pure alphanumeric.. not apple names with spaces and apostrophe.

881 Router - How many Vlans are supported (Dhcp scopes)

Dear All!
After calling Cisco three times without response, I need to ask this most likely simple question right here.
How many vlans does a 881 router support? Will this be the same number for dhcp scopes?
Thanks for your time...
..hopefully you guys can sort it for me ;)

Hi,
On every Cisco router platform each interface,sub interface & VLAN
uses a system reference point referred to as an Interface Desciptor Block.
IDB
Depending on processing power of each platform determines the number
of IDBs the router platform can support.
On all IOS version referred to in the documentation a Cisco 881
can support up to 300 IDBs
The router has physically 5 interfaces (4 x LAN + 1 x WAN)
300 - 5 = 295
So you shouldin theory be able to build
295/2 = 147 VLANs & 147 SVIs
Remember a VLAN uses 1 IDB & an SVI uses 1 IDB
See this link for more info.
http://www.cisco.com/c/en/us/support/docs/ios-nx-os-software/ios-software-releases-122-mainline/15096-idb-limit.html#max_no_interfaces
Hope this helps
Regards
Alex

881 Router Wireless Module

Similar Messages

Maybe you are looking for