890FXA-GD70 no post

Specs:
AMD 1090T 6 core phenom
MSI 890FXA-GD70
Corsair CMX4GX3M2A1600C9 pc1600 x2
PC Power and Cooling 850 watt power supply
Caviar green 1Tb
Samsung 223b dvdrw
Antec 1200 case
5870 ATI
Swap parts
Kingston HyperX PC1600 DDRIII
AMD 955T Black Phenom II 4 core
Antec Truepower 2.0 tested good ATX 430 watt
Radeon 7x known good pci graphics card
I'm building this for a buddy and I'm stumped. I breadboarded it up on the box with the proc/heat sink, one stick of the corsair (also tried Kingston), and the PCP&C power supply and I couldn't get the board to post. I have subbed the processor with a 955t black 4 core phenom II,the memory with Kingston hyper x, the power supply with an Antec truepower 2.0. The alphanumeric LEDs would blink and the DDR leds came on but no cpu fan. So we RMA'd back to Newegg and did it all over again today with the replacement board fore even less response.
Only the DDR phase lights will come on, the fan on the graphics and cpu would wiggle a bit and stop, and the psu fan would stay on. This time the alphanumeric leds didn't flash at all. I followed all the troubleshooting for no post on Tom's Hardware, I've swapped out every component, and the second mobo is seemingly also dead? Is this a bad batch of boards? Why no post? Thanks in advance

The 890FXA-GD70 supports the 1090T and 955 without any need to update the BIOS so we know they are supported. Do you think there's actually a chance both CPUs are faulty? Inspect both CPUs for any bent pins or signs of damage.
You've tried another power supply and different RAM so they're not likely culprits. A short isn't that likely since you have the system on a sheet of cardboard.
You haven't plugged the CPU fan into the sys fan socket by mistake? Different number of pins I know but worth just checking with you. Another thing to check is that the CMOS jumper isn't set on clear by mistake when trying to boot up.
Quote from: Mark on 12-December-10, 21:15:55
Have you cleared the CMOS? >>Clear CMOS Guide<<
Do try clearing the CMOS.

Similar Messages

890FXA-GD70 no post with PERC6i

Per subject line; I have a 890FXA-GD70 which I can't get to post with a PERC6i card.
Board code FF and system restarts itself in a cycle. No video display. CPU phase 3 LEDs light up. 2 memory phase LEDs lit.
Remove PERC card; system posts fine & remains stable.
The PERC6i works fine in other systems (servers).
I know its not a desktop product but I've read other people's spec on other forums who've used this card successfully in this board.
I've disabled onboard Raid and all other I/O devices in the bios (v1.7). Next step is to contact MSI Tech Support but given the phase 3 CPU LEDs I'm wondering if there's a CPU setting in the bios I can adjust that might help or if there's anyone else who's had the same problem with this or another Raid card & resolved it??
Spec:
890FXA-GD70 (bios v1.7)
AMD Phenom X6 Thuban 1055T (not OC'd yet)
2x4GB Gskill Ripjaws PC1333 (not OC'd yet)
Asus EAH5830
CoolerMaster SilentPro M1000

Quote from: Fredrik on 02-November-10, 10:19:25
Where do you put it?
In any of the available PCI-E slots. The GPU takes up the first 2 slots (x16 & x1). I’ve yet to try moving the GPU to another slot but afaik the GPU needs to be in the first PCI-E slot in this board in order to work...correct me if I’m wrong.
Quote from: Fredrik on 02-November-10, 10:19:25
Is it that card in particular or any card you put in?
This card in particular. I need it to run ESX4i. The card works fine in other systems.
Quote from: Fredrik on 02-November-10, 10:19:25
I get allergic reactions from RipJaws and CoolerMaster. But surely they can't be the culprits this time. :undecided
TBH I was unaware of issues with RipJaws & CoolerMaster PSUs. Need to research it more.
Quote from: Fredrik on 02-November-10, 10:19:25
You could try with a single stick of memory with correct/manuf. recommended voltage.
Tried with 1DIMM; same.
Using default voltages. I’ll check what voltage is recommended by Gskill.
Tks for the replies so far.

890FXA-GD70 No POST, no LEDs except HDD_LED constant ON

Powered on machine and received no POST. HDD_LED constant RED on, no CPU_PHASE LEDs lit, no DDR_PHASE LEDs lit, no LCD codes on the on-board display (display no lit at all). Tried removing components one by one (GPU, memory modules, etc) to isolate problem but could not. Checked CPU for bent pins, reseated, and checked for visible shorts behind board/standoffs. P/S (Corsair TX650W) voltages all correct when tested while not connected. Barebones setup outside case gave same result/error. All fans fire up & HDDs spin up.
Antec 900
Corsair TX650W
AMD 970 (x/ZALMAN CNPS9900)
MSI 890FXA-GD70, BIOS v1.8
OCZ Gold 1600 4 X 2GB (8-8-8-24-1T)
Sapphire AMD 6970 reference board
WD Black 750GB (2x)
All help is appreciated,
Thanks

Quote
8GB (4 X 2GB) OCZ Gold DDR3 1600 @ 1333 7-7-7-20
Take out all sticks but just 1, see what happens.
Also clear the cmos, and leave all memory timings on auto.
Quote
This has been my faithful setup for about 15 months since I upgraded from the 790GX-GD65.
So this board never worked? Or did you upgrade 15 months ago and it worked until yesterday.
Please be specific.

890FXA-GD70-Not Posting and Memory Issues

Purchased new 890FXA-GD70 board over the weekend and I am having problems after new build. Board will not post with 2 stick of Corsair DDR3 4GB PC1600 in slots 1 and 2. I removed one stick in slot 2 and board posted. I installed all drivers and Win 7 pro and added the second stick into slot 2 and will not post again. I moved the 2GB stick to slot 3 and the computer boots and seems to run fine. Should'nt DDR3 be run in slots 1 and 2?
System
CPU-AMD Phenom II x4 945
Motherboard-890FXA-GD70
Memory-Corsair DDR3 4GB 2 sticks at 2GB each PC1600 Dual
Video Card-EVGA GTS250 512MB
Hard Drives-Western Digital Black Edition 500Gb
OS-Windows 7 Professional
Power Supply-Corsair 750

After checking the boards and google search, it appears that several other people are having the same issue. If the memory sticks are placed in dimm1 and dimm3 the board seems to post and runs fine. But that will not produce dual channel memory. Should I change memory to another brand? What is the best memory for this board. The computer has been running all day and seems to be stable but, just worried that memory is still incorrect and only have 10 days to return to Frys. I have also flashed the bios to 1.6! It appears that after reading several other post on this forum, they had to return the board, could I have a bad board?

MSI 890FXA-GD70 LED panel debug show 2A, unable to post

Dear guys,
I need some help with my motherboard, recently did a new set up but having some problem. My computer is unable to boot most of the time but sometime it is able to post.
Been having this problem since i did the new set up but recently it is unable to boot most of the time.
It appears to be stuck showing 2A on the led debug panel unable to get past that.
my set up as follows :
AMD Phenom X4 965
890FXA-gd70'
8gb ram Team elite ddr3 1333 cl9 2x4gb kit
sapphire 5770 vapourcool x2 Crossfire
western digital 1 tb caviar black x2 Raid 0
Coolermaster slient pro 600w psu
Running Win 7
Bios version 1.7.
All drivers are the latest I have from the MSI website, graphic drivers are the latest I have from ATI.
Crossfire has been installed as instructed from the manual, slot 1(closet to the cpu and slot 5)

The mainboard can't be unstable at crossfire,
but eventually broken one of the VGA's or weak PSU yes.
Quote
What do you suggest if I am still stuck on 2A after using only 1 graphic card?
If that hapends, test with the second VGA alone in the 1st PCI-E slot
Quote
8gb ram Team elite ddr3 1333 cl9 2x4gb kit
Also leave one memory stick only in 1st DIMM close to CPU socket,
remove power cord from the PSU,
then do >>Clear CMOS Guide<<
and try to boot

890FXA-GD70 Will not POST

I recently purchased a new MSI 890FXA-GD70 motherboard from Newegg.com, along with a couple other upgrades. I put together my new computer consisting of this motherboard, a new AMD Phenom II X4 965 BE CPU, 8 GB of RAM, and an older nVidia 9800GTX+ GPU. The memory and video card have worked in previous machines.This PC will not boot. It will not even POST. The lights on the motherboard flash like mad, and the LED readout just flashes "FF." I RMA'd it to NewEgg, but was denied due to peeling the sticker off the back of the MOBO, so now I'll send it to MSI. I'm hoping for some good news.

Quote from: Bas on 06-November-11, 04:07:12
>>Posting Guide<<
Sorry, here are my specs...
•   AMD Phenom II 965 Black Edition CPU (NEW)
•   MSI 890FXA-GD70 Motherboard (NEW)
•   G.SKILL Value Series 8GB (4 x 4GB) 240-Pin DDR3 SDRAM DDR3 1333 (PC3 10600) (NEW)
•   XFX 9800 GTX+ 512MB nvidia GPU
•   Western Digital 1TB HDD SATA 7200RPM
•   Antec SmartPower 2.0 SP-500 500W ATX12V SLI Ready Modular Power Supply (+3.3V@32A, +5V@35A, +12V1@17A, +12V2@19A, [email protected], +5VSB@2A)

890fxa-gd70 motherboard no longer posts; blinking ff debug code

As topic says I am no longer capable of starting up my computer. Here is a detailed list of specs:
Msi 890fxa-gd70 mainboard
OCZ 1333mhz memory 2x2 gb
Amd phenom 2 1055t 6-core processor
Seasonic x-760 psu
ASus geforce gtx 580
Corsair a50 air cooler
After waking up this morning my computer was unable to post. I had a very mild overclock of 3.5 ghz from stock 2.8 ghz at 1.39-1.4 volts and ram multi lowered to keep things stable. I had an issue like this before involving g.skill memory but got this ocz kit to resolve the problem. I breadboarded the setup keeping only one stick in the slot closest to the CPU. Ive tried clearing CMOS while CPU out of socket and reseating CPU. All 4 CPU phase LEDs light up, NB phase light up, sOuthbridge LEDs light up and 2 DDR phase LEDs light on the motherboard. All these components were working before. After using a known working 2-core phenom 555 CPU, working 550w psu from tt, and a plethora of video cards, I'm thinking the bios or DDR slots on the motherboard has finally kicked the bucket. Is there anything else I can do to help resolve my problem?

Quote from: Froggy Gremlin on 25-September-12, 04:12:53
A low post count doesn't necessarily mean the people trying to assist are ignorant buffoons.
agreed! i only have over 570+ posts but ive been building computers since the 1990's when processors whern't compact single packages and where on literally a pci type board!
low posts don't mean we dont know what where talking about and ignorant posts like that are likely to make it so you get no support from us as its disrespectful!

Msi 890fxa-gd70 posting problems

the problem started after i installed a new thermaltake frio cpu cooler, i installed it outside of the case on the box the motherboard came in. I get the splash screen but the keyboard wont respond and hangs at code 38 with a usb mouse and keyboard and one sata Hdd & dvd drive plugged in. if i remove the mouse and keyboard it goes to code 78 and hangs. if i remove the hdd & dvd drive it cycles through and tells me i have no boot device. i have tried different combinations and tryed moving the ram around, just 1 stick!. i have tried clearing the cmos throughout doing the different combinations. I have tried all the different sata ports for just the hdd, and i have tried all the different usb ports to try to get the keyboard to register, i did also try another known working usb keyboard. this motherboard has never been OC'ed this is a custom build computer for a friend so i only have limited time to keep messing around with combinations of hardware. the ram is tested and i also tried using one of my sticks from my rig with no luck. so here is the specs
msi 890fxa-gd70 mobo - bios 1.6
AMD phen II 555 BE - no oc and no unlocked cores
G. Skill rip jaws 1333 mhz cas 9
this rig was working perfect for 2 weeks before i tried to install the new HS, i already checked the pins on the cpu to make sure that i didnt damaged it. i always practice safe ESD rules and was wearing my bracelet. i was very careful when installing the new cooler and made sure it wasn't too tight of a fit, i have already done this before on my rig same mobo, cpu and cooler and had no problems with it. I am stuck in a corner and I am hoping to find some help out... Any suggestions? Please and Thank You in advance

i have tried that also, the main problem is that i cant get it past code 38 with an usb keyboard in it so that i can enter the bios. i can get it to cycle through and not hang, but that is without any keyboard or Hdd so im back at square one. i still need to try an PS/2 keyboard but finding one is actually harder than i thought it would be. this board hasn't have a bios update, it came with 1.6 already on it. its not even an month old yet. but thank you for an possible answer to this dilemma.

890FXA-GD70 Will Not Wake From S3 Sleep

890FXA-GD70 will not wake from S3 sleep; the power comes back on and the fans run but the video never returns and the system hard locks with a POST code of 22 or 24. Other than this issue the system is rock solid.
Windows 7 Ultimate 64
AMD Phenom II X4 955 Processor
Sapphire 5870 Graphics
Crucial M4 SSD
Corsair DDR3
No overclock
I have reproduced the issue on two 890FXA-GD70s motherboards and I am convinced that this is not a result of a failed motherboard. I also was able to move my fully installed SSD hard drive, processor, memory and graphics card to an Asus 890FX board and successfully wake from S3 sleep proving that my OS and driver installation are working correctly.
I know how to properly set the BIOS as I have installed many 890GXM-G65 motherboards for S3 sleep without issue. The problem seems unique to the 890FXA-GD70.
Is there a fix for this?

I have identified the cause. The "Extra RAID/IDE Controller" must be "Enabled" to use S3; otherwise the system will hang on the wake event. This is true even if the "Extra RAID/IDE Controller" goes unused. The "Extra RAID/IDE Controller" must be set to "Enabled" for S3 sleep to wake.
This would seem to me to be a bug since none of the other MSI boards I have used require the optional IDE controller to be enabled in order for S3 to function properly.

MSI 890FXA-GD70 w/ 2xIntel 510 120GB in RAID 0 on Locks up and BSOD

I am getting hard lockups and BSOD from the following
OS: Win7x64
MB: MSI 890FXA-GD70 w/ latest BIOS
CPU: AMD Phenom II X6 1100T
HD: 2xIntel SSD 520 120GB SSD RAID 0
VID: ATI FirePro V4800
RAM: G.SKILL Ripjaws Series 8GB (4 x 2GB) 240-Pin DDR3 1600 F3-12800CL9D-4GBRL
I have swapped power supplies. I have swapped identical RAM. I have swapped video cards. I have used Ultimate Boot CD to run Memtest and other stress tests and everything passes with flying colors. BIOS is loaded with defaults fail safe. RAID array is created using all defaults for a RAID 0. Everything points to SSD firmware or other issues. Maybe RAID 0 with 2 Intel 510's using a AMD SB850 is not supported? Firmware versions on the 510's are both PPG4 which is the latest. Am I doing something wrong? Anyone have any ideas? I am very disappointed that that I can not get my RAID 0 stable. BTW I am doing no overclocking etc. Hardware and errors follow. Thanks!
Microsoft (R) Windows Debugger Version 6.12.0002.633 AMD64 Copyright (c) Microsoft Corporation. All rights reserved. Loading Dump File [D:\Kingston\BSODDmpFiles\chapmunger\Windows_NT6_BSOD_jcgriff2\031112-15210-01.dmp] Mini Kernel Dump File: Only registers and stack trace are available Symbol search path is: SRV*c:\symbols*http://msdl.microsoft.com/download/symbols Executable search path is: Windows 7 Kernel Version 7601 (Service Pack 1) MP (6 procs) Free x64 Product: WinNt, suite: TerminalServer SingleUserTS Built by: 7601.17640.amd64fre.win7sp1_gdr.110622-1506 Machine Name: Kernel base = 0xfffff800`02c5a000 PsLoadedModuleList = 0xfffff800`02e9f670 Debug session time: Sun Mar 11 00:13:13.124 2012 (UTC - 6:00) System Uptime: 0 days 0:04:46.289 Loading Kernel Symbols ....................................... ........................ ....................................... ......................... .............................. Loading User Symbols Loading unloaded module list ....... ******************************************************************************* * * * Bugcheck Analysis * * * ******************************************************************************* Use !analyze -v to get detailed debugging information. BugCheck D1, {fffff88001308c08, 2, 8, fffff88001308c08} Probably caused by : Ntfs.sys ( Ntfs! ?? ::NNGAKEGL::`string'+2bf0 ) Followup: MachineOwner --------- 4: kd> !analyze -v ******************************************************************************* * * * Bugcheck Analysis * * * ******************************************************************************* DRIVER_IRQL_NOT_LESS_OR_EQUAL (d1) An attempt was made to access a pageable (or completely invalid) address at an interrupt request level (IRQL) that is too high. This is usually caused by drivers using improper addresses. If kernel debugger is available get stack backtrace. Arguments: Arg1: fffff88001308c08, memory referenced Arg2: 0000000000000002, IRQL Arg3: 0000000000000008, value 0 = read operation, 1 = write operation Arg4: fffff88001308c08, address which referenced memory Debugging Details: ------------------ READ_ADDRESS: GetPointerFromAddress: unable to read from fffff80002f09100 fffff88001308c08 CURRENT_IRQL: 2 FAULTING_IP: Ntfs! ?? ::NNGAKEGL::`string'+2bf0 fffff880`01308c08 55 push rbp CUSTOMER_CRASH_COUNT: 1 DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT BUGCHECK_STR: 0xD1 PROCESS_NAME: explorer.exe TRAP_FRAME: fffff8800a580fb0 -- (.trap 0xfffff8800a580fb0) NOTE: The trap frame does not contain all registers. Some register values may be zeroed or incorrect. rax=fffff88001308c08 rbx=0000000000000000 rcx=fffff8800a581180 rdx=fffff8800a582770 rsi=0000000000000000 rdi=0000000000000000 rip=fffff88001308c08 rsp=fffff8800a581148 rbp=fffff8800a581280 r8=fffff8800a581900 r9=fffff8800a581280 r10=fffff8800a582970 r11=fffff8800a5811b8 r12=0000000000000000 r13=0000000000000000 r14=0000000000000000 r15=0000000000000000 iopl=0 nv up ei ng nz na pe nc Ntfs! ?? ::NNGAKEGL::`string'+0x2bf0: fffff880`01308c08 55 push rbp Resetting default scope LAST_CONTROL_TRANSFER: from fffff80002cd61e9 to fffff80002cd6c40 FAILED_INSTRUCTION_ADDRESS: Ntfs! ?? ::NNGAKEGL::`string'+2bf0 fffff880`01308c08 55 push rbp STACK_TEXT: fffff880`0a580e68 fffff800`02cd61e9 : 00000000`0000000a fffff880`01308c08 00000000`00000002 00000000`00000008 : nt!KeBugCheckEx fffff880`0a580e70 fffff800`02cd4e60 : 00000000`000000e9 00000000`00000000 fffff800`02ce1845 fffff880`01269840 : nt!KiBugCheckDispatch+0x69 fffff880`0a580fb0 fffff880`01308c08 : fffff800`02d02a7c 00000000`00000001 fffffa80`09667000 fffffa80`08c92d01 : nt!KiPageFault+0x260 fffff880`0a581148 fffff800`02d02a7c : 00000000`00000001 fffffa80`09667000 fffffa80`08c92d01 fffffa80`08d1aea0 : Ntfs! ?? ::NNGAKEGL::`string'+0x2bf0 fffff880`0a581150 fffff800`02d024fd : fffff880`01269834 fffff880`0a582770 00000000`00000000 fffff880`01219000 : nt!_C_specific_handler+0x8c fffff880`0a5811c0 fffff800`02d012d5 : fffff880`01269834 fffff880`0a581238 fffff880`0a5820a8 fffff880`01219000 : nt!RtlpExecuteHandlerForException+0xd fffff880`0a5811f0 fffff800`02d12361 : fffff880`0a5820a8 fffff880`0a581900 fffff880`00000000 ffff5fff`ffffffff : nt!RtlDispatchException+0x415 fffff880`0a5818d0 00000000`00000000 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : nt!KiDispatchException+0x135 STACK_COMMAND: kb FOLLOWUP_IP: Ntfs! ?? ::NNGAKEGL::`string'+2bf0 fffff880`01308c08 55 push rbp SYMBOL_STACK_INDEX: 3 SYMBOL_NAME: Ntfs! ?? ::NNGAKEGL::`string'+2bf0 FOLLOWUP_NAME: MachineOwner MODULE_NAME: Ntfs IMAGE_NAME: Ntfs.sys DEBUG_FLR_IMAGE_TIMESTAMP: 4d79997b FAILURE_BUCKET_ID: X64_0xD1_CODE_AV_BAD_IP_Ntfs!_??_::NNGAKEGL::_string_+2bf0 BUCKET_ID: X64_0xD1_CODE_AV_BAD_IP_Ntfs!_??_::NNGAKEGL::_string_+2bf0 Followup: MachineOwner ---------
Loading Dump File [D:\Kingston\BSODDmpFiles\chapmunger\Windows_NT6_BSOD_jcgriff2\031012-22963-01.dmp] Mini Kernel Dump File: Only registers and stack trace are available Symbol search path is: SRV*c:\symbols*http://msdl.microsoft.com/download/symbols Executable search path is: Windows 7 Kernel Version 7600 MP (6 procs) Free x64 Product: WinNt, suite: TerminalServer SingleUserTS Built by: 7600.16841.amd64fre.win7_gdr.110622-1503 Machine Name: Kernel base = 0xfffff800`0285a000 PsLoadedModuleList = 0xfffff800`02a97e70 Debug session time: Sat Mar 10 22:15:14.047 2012 (UTC - 6:00) System Uptime: 0 days 0:02:55.014 Loading Kernel Symbols ....................................... ........................ ....................................... ......................... ............. Loading User Symbols Loading unloaded module list ..... ******************************************************************************* * * * Bugcheck Analysis * * * ******************************************************************************* Use !analyze -v to get detailed debugging information. BugCheck F4, {3, fffffa8009348b30, fffffa8009348e10, fffff80002bd2300} Probably caused by : hardware_disk Followup: MachineOwner --------- 3: kd> !analyze -v ******************************************************************************* * * * Bugcheck Analysis * * * ******************************************************************************* CRITICAL_OBJECT_TERMINATION (f4) A process or thread crucial to system operation has unexpectedly exited or been terminated. Several processes and threads are necessary for the operation of the system; when they are terminated (for any reason), the system can no longer function. Arguments: Arg1: 0000000000000003, Process Arg2: fffffa8009348b30, Terminating object Arg3: fffffa8009348e10, Process image file name Arg4: fffff80002bd2300, Explanatory message (ascii) Debugging Details: ------------------ PROCESS_OBJECT: fffffa8009348b30 IMAGE_NAME: hardware_disk DEBUG_FLR_IMAGE_TIMESTAMP: 0 FAULTING_MODULE: 0000000000000000 PROCESS_NAME: csrss.exe EXCEPTION_RECORD: fffff88001ed8b78 -- (.exr 0xfffff88001ed8b78) ExceptionAddress: 0000000077514e8f ExceptionCode: c0000006 (In-page I/O error) ExceptionFlags: 00000000 NumberParameters: 3 Parameter[0]: 0000000000000000 Parameter[1]: 000007fefd47d8a8 Parameter[2]: 00000000c000000e Inpage operation failed at 000007fefd47d8a8, due to I/O error 00000000c000000e EXCEPTION_CODE: (NTSTATUS) 0xc0000006 - The instruction at 0x%p referenced memory at 0x%p. The required data was not placed into memory because of an I/O error status of 0x%x. CUSTOMER_CRASH_COUNT: 1 DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT CURRENT_IRQL: 0 ERROR_CODE: (NTSTATUS) 0xc0000006 - The instruction at 0x%p referenced memory at 0x%p. The required data was not placed into memory because of an I/O error status of 0x%x. EXCEPTION_PARAMETER1: 0000000000000000 EXCEPTION_PARAMETER2: 000007fefd47d8a8 EXCEPTION_PARAMETER3: 00000000c000000e IO_ERROR: (NTSTATUS) 0xc000000e - A device which does not exist was specified. EXCEPTION_STR: 0xc0000006_c000000e FAULTING_IP: +23a 00000000`77514e8f ?? ??? BUGCHECK_STR: 0xF4_IOERR_C000000E FOLLOWUP_IP: +23a 000007fe`fd47d8a8 ?? ??? FOLLOWUP_NAME: MachineOwner MODULE_NAME: hardware_disk STACK_COMMAND: kb FAILURE_BUCKET_ID: X64_0xF4_IOERR_C000000E_IMAGE_hardware_ disk BUCKET_ID: X64_0xF4_IOERR_C000000E_IMAGE_hardware_ disk

Thanks for the help! It is appreciated. Power supply is Antec 380W. I have tried swapping out with identical one - both were brand new and I have had pretty good luck with Antec in the past so I kind of doubt that's it. Wish it was so easy! The machine is on a good line interactive UPS as well so power fluctuations are not causing this.
I am using the hardware RAID on the SB850 - it requires loading the latest driver from USB during installation. But prior to that it requires a Ctrl-F and into the RAID setup. I choose RAID 0 and then select both Intel 510 120GB SATA III. The two SSD have the exact same firmware which is the latest per Intel Website.
Drivers are the latest for Win7x64 from here:
http://www.msi.com/product/mb/890FXA-GD70.html#/?div=Driver&os=Vista%2064
This problem is posted in two other spots - Intel Forums and Windows Seven Forums
http://communities.intel.com/thread/28220?tstart=0
http://www.sevenforums.com/crashes-debugging/218850-bsod-msi-890fxa-gd70-w-2xintel-ssd-520-120gb-ssd-raid-0-a.html
No one has been able to solve it yet. Seems like MSI and Intel are both good companies but these products are not compatible in the configuration I am attempting.

Code FF :( Please Help MSI 890FXA-GD70

Specs:
MSI 890FXA-GD70 AM3+ AMD 890FX SATA 6Gb/s USB 3.0 ATX AMD Motherboard
AMD Phenom II X6 1090T Black Edition Thuban 3.2GHz Socket AM3 125W
G.SKILL Ripjaws Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800)
EVGA GeForce GTX460 1 GB Superclocked GDDR5 PCI-Express 2.0 Graphics Card -
Western Digital Caviar Black 1 TB Bulk/OEM Hard Drive 3.5 Inch, 32 MB Cache, 7200 RPM SATA II
Corsair - Gaming Series 700-Watt ATX CPU Power Supply
I had everything working for 8 months or so then everything suddenly went bonkers....my cpu wouldn't start up. I replaced my PSU and took everything apart and I had it working outside of my case for 2 weeks and then it decided not to start up again.....I resat all components with no luck.
I RMA'd my motherboard to MSI and had it swapped out. Now....I went to reseat everything and like an idiot; I had spilled excess arctic silver 5 onto the mainboard socket and the PCU. I cleaned everything best I could without any solution and tried to start it up; CODE FF (only using 1 stick of ram and video card).
I did some reading and picked up some loctite electrical cleaner http://www.rshughes.com/products/079340_1174633.html
and cleaned everything out. I used a fine brush to clean out the socket.
Now; I installed pcu; heat sink; 1 stick ram (tried all slots) video card. I also made sure my power connections were hooked up---pcu and mainboard---I still get a code FF immediately..no post; nothing. Every time it goes to code FF and nothing else. Fans run and the all lights on the motherboard light up...the PCU lights are on as well. (all 4)
I've tried every solution I've read on this board and whatever google could find for me....my questions is (sorry for long story); should I just replace my PCU and motherboard as I messed it up with the arctic 5?
Thanks for any insight!

Quote from: Scrumhalf01 on 29-February-12, 22:57:23
Don't have the spare parts or I would have done that.....do computer shops willingly let you test out pieces you bring in to their shops? If there was an issue with the motherboard could it fry the new pcu installed?
Quote from: Scrumhalf01 on 29-February-12, 22:57:23
Don't have the spare parts or I would have done that.....do computer shops willingly let you test out pieces you bring in to their shops?
yes eventually, you have to ask them
Quote
If there was an issue with the motherboard could it fry the new pcu installed?
yes its possible

MSI 890FXA-GD70 | ATI/AMD Downloads | Advice needed on a few things

Hi
I have a few questions to which someone would probably know off-hand the answers to, so here goes:
1. I purchased the MSI 890FXA-GD70 along with an AMD Phenom X6 1090T BE CPU and need some recommendations on which 8GB (2 x 4) memory kit to purchase. This will be used with a 64 bit OS (Win 7/Linux) and would like to slightly overclock the memory (IF NEEDED) to reach a CPU speed of 4.5GHz. I would prefer Patriot, Corsair or Gskill DDR3 10666 or higher...whatever would do the job.
2. This question involves downloading and installing the Catylist drivers for the motherboard. I DO NOT use an ATI/AMD GPU, but rather a nVidia 580 Reference board, so I am under the assumption that I DO NOT need to download any of the catalyst drivers EXCEPT the following:
AHCI
SB Driver
RAID
Those are directly related to everything BUT the GPU...if I am wrong, please correct me. For the following components, I usually go to the individual manufactures web-site to download drivers:
RealTek LAN: RTL-8111DL PCI-E LAN Driver - v7.034 - 2010-DEC-22
IEEE 1394: From VIA - VT6315N
Realtek Audio: From Realtek ALC889/ALC892
USB 3.0: From NEC
I have not yet installed the mobo yet as I am awaiting for memory suggestions, thus I am grabbing all the absolute latest drivers for my system beforehand.
I just downloaded the RTM SP1 for Win 7 64 file and addition to that, wish to merge (slipstream) the above drivers into the Win 7 OEM DVD so I have everything ready to go.
3. In regards to AHCI, do I or can I use that with a fresh install of Win 7 or is AHCI reserved for those with SSD's ? I know I can use AHCI via Linux which I do on several other boxes, however, I am not sure about Windows 7 64.
I suppose that wraps it up. All this is replacing my DFI LanParty 790FXB-M2RSH board in which I fell in love with, however, DFI is not supporting/making that line of boards again, so my choice was between MSI and Gigabyte. Obviously, you can tell who won.
If there is anything I should be 'prepaired' for (e.g. bugs, troubles, etc.) feel free to post the information.
Thank You Very Much
Tim
ARS N9NU
Digital Audio Productions

Quote
some recommendations on which 8GB (2 x 4) memory kit to purchase
The following kit is in use by some of the forum members and it performs exemplary in all instances. Although being a 1333 it will OC to 1600 at 1,5V. The link is for the UK store, but they are available through the Crucial US store as well. http://www.crucial.com/uk/store/mpartspecs.aspx?mtbpoid=930A546EA5CA7304
Quote
This question involves downloading and installing the Catylist drivers for the motherboard
Your analysis is quite correct. Insert your GPU card before your windows installation. Once the installation is complete you can then install the latest NVidia drivers, or start with the ones that shipped with your GPU.
Quote
If there is anything I should be 'prepaired' for
Initially start with only one mem module, single optical drive, single HDD and GPU card. Ideally do ar barebones build outside the case on a non-conducting surface. Get everything up and running, and then transfer everything to the case. Test if all is still normal, and then start to add the other copmponents, ie. 2nd mem module, HDDs, etc.

890FXA-GD70 bios update via Live Updat & now won't load windows...help pls

Hi There
First off, please excuse the fact that I am not very experienced with the tech aspects of a home build (which this is & I bought off the builder), or any build for that matter..
I was getting a 'keyboard/interface' press f1 to continue error message, when I started my computer, along with most of the usb ports not working when windows 7 ultimate (64) sp1 (build 7601) loads.
Otherwise it was working fine..
So I deceided to follow the instructions of the Live Update tool & used the total installer to update the bios from American Megatrends V1.10 06/30/2011 to the latest bios. I know now that wasn't very wise (why is it even an option if it can do soooo much harm?).
After it updated the bios there was a question (which I don't recall of course), something about ROM I think and not being the same, with 3 choices to correct it and I'm pretty sure I went with the 1st option for it to be corrected.
So now when I turn the computer on it starts loading everything (I can get in to the bios setup), right after it shows the windows logo it flashes a blue screen with some type on it & goes to windows startup repair which of course doesn't help & tries to do a system recovery which also doesn't work.
I don't want to do any more damage by fiddling around with things I know little about.
I was encouraged to read in one of the post answers that if it gets to the point where Windows goes to load than the mobo is ok...hopefully!
Any assistance would be greatly appreciated.
Specs: (Copied from a Belarc Advisor scan)
O/S Windows 7 Ultimate (x64) Service Pack 1 (build 7601)
Main Board: 890FXA-GD70, Bus Clock: 200 megahertz BIOS: American Megatrends V1.10 06/30/2011
Processor: 3.30 gigahertz AMD Phenom II X 6 1100T Multi Core Not hyper-threaded
Drive: ST3500418AS Hard drive 500 gig SMART Status: Healthy
HL-DT-ST DVDRAM GH24LS50 ATA Device (optical drive)
Optiarc DVD RW AD-728OS ATA Device (optical drive)
PSU: Corsair GS500
12 gigs of RAM 1. 2048, 2. 2048, 3. 4096 4. 4096
Display adapter: MSI R7850 Twin Frozr 2GD5
Local Drive Volumes: c: (NTFS on drive 0)
Hopefully that is the required info on the specs.
Thanks in advance for any assistance.
Rob

yes the BIOS controls the CMOS from that User interface with all the settings menus!
and yes its in there where you can see what Drive mode its set at!
if its using the older style BIOS like my board has and not a UEFI then in this heading set:
1: go into your BIOS (press Delete)
2: Integrated Perifirals
3: On-Chip ATA Devices
4: Raid Mode <--- the options for that should be in there if its the same and may have been set to IDE mode before the update but may be set to AHCI now after you flashed the BIOS via live update which is more then likely why your getting a BSOD as it in the wrong operating mode!

MSI 890FXA-GD70 AM3 - Hard Drive in Sata Port 6 Not recognized in WIN7-[SOLVED]

I just bought this motherboard (MSI 890FXA-GD70 AM3), new memory, case and processor. I love it. But while I can put something together, I do not consider myself much more then an experienced novice.
Anyway, I bought a 5th hard drive and plugged it into SATA connector 6. Connector 5 remains unused. The new hard drive is recognized when the BIOS boots, but in Windows 7, I only show the first 4 drives like always. I just want to use this drive as a 5th hard drive for normal use and storage.
I went into the BIOS to see if there was a setting I was missing; read through the posts to see if I could find the answer; and prayed to GOD, but nothing has worked! I have found nothing on this topic, but then the FORUM is hard to navigate after a while with people not carefully choosing their topic subject name. (Why do people sometimes post - I HAVE A PROBLEM - without anything in the SUBJECT line to help the casual reader know what they are asking about?) My searches were fruitless, but then I know the key to a good search is using the right keywords.
I know this is going to turn out to be a simple setting, but can you help? Thanks in advance! And when the solution is presented, I will post back that ALL IS WELL!

PROBLEM SOLVED! Found it myself through careful research.
This is the link that helped me: http://www.ithinkdiff.com/how-to-enable-ahci-in-windows-7-rc-after-installation/
Apparently, because I had IDE and not AHCI enabled in the BIOS, only the first 4 ports were being identified. AND because I had not not changed the BIOS to AHCI before the installation of Windows 7, NO obvious way to change the setting AFTERWARDS!
In part what the post link above states:
AHCI (Advanced Host Controller Interface) enables native command queuing and hot-plugging through SATA host controllers (Serial-ATA) for your hard drives. In many scenarios it enables more efficient multi-tasking. Vista was the first Windows OS to support AHCI out of the box, where as Windows 7 does the same. But an issue with AHCI is that if you install the OS without enabling AHCI in the BIOS, enabling it after installation will render your OS unusable. This is because Windows disable the AHCI driver since it is not needed during the installation.
There is one way to fix this, although you need to have knowledge of registry editing. The detailed steps from Microsoft are as follows:
To resolve this issue, enable the AHCI driver in the registry before you change the SATA mode of the boot drive. To do this, follow these steps:
1. Exit all Windows-based programs.
2. Click Start, type regedit in the Start Search box, and then press ENTER.
3. If you receive the User Account Control dialog box, click Continue.
4. Locate and then click the following registry subkey: HKEY_LOCAL_MACHINESystemCurrentControlS etServicesMsahci
5. In the right pane, right-click Start in the Name column, and then click Modify.
6. In the Value data box, type 0, and then click OK.
7. On the File menu, click Exit to close Registry Editor.
After this you’ll have to restart your computer, go to BIOS and enable AHCI. When you log in to Windows again, you’ll notice the installation of drivers for AHCI. Another restart will be required to finish the driver installation.
I had been trying to select something in the BIOS other then IDE (choices are IDE, AHCI and RAID) to see if that would result in my 5th drive being recognized, but when I selected AHCI or RAID, the OS would flash the EVIL blue screen before it completed booting into Window 7.
I copied the instructions here in case the link gets disabled in the future. This link explained why I was having the problem I was having and how to solve it.
Thanks to everyone who tried to assist. I consider this closed.

890FXA-GD70 Overclocking DDR 1333 Memory to 1600

I am a professional network administrator and have been building my own computers since 2002. However, am not a gamer and have never over clocked anything. I just built a new rig based on the on a MSI 890FXA-GD70 mobo and an AMD 1090T processor. The mobo supported 1600, 1800, and 2000 speeds of over clocked DDR3 1333 RAM. I purchased 2 2GB sticks of Corsair Dominator CMP4GX3M2A1600C8 RAM because it was supposed to be able to handle being OCed to 1600 with no problems. My system is running great but it automatically detects the RAM as 1333 MHz with timings of 9-9-9-24 instead of the advertised 1600 with 8-8-8-24. I went into the BIOS and manually set the timings to 8-8-8-24 and it worked fine. I then set the ratio from Auto to 1/4 which showed the speed of the RAM at 1600 MHz. However, when I told it to save the setting and reboot it would not come up at all. The only way to recover my system was to use the jumpers on the mobo to reset the CMOS back to its original settings. From everything I've read it's easy to set the RAM to 1600. Both my mobo and the RAM are advertised by the manufacturer as supporting 1600 DDR3. I would appreciate any advice anyone has. Specific settings for my mobo would be appreciated. My system is fine the way it is but I paid extra to have certified 1600 MHz RAM and would like to be able to use it at that speed. Thanks in advance.

Mobilebyrd,
I received a personal message from you with the question below but for some reason my account won't let me send personal messages or view to profile to get your e-mail address. Hopefully you will get this. Please post a reply to this forum if you have any more questions. Hopefully it will help others how are having the same problem. I have posted the question and answer. Please keep in mind that the settings I used are for the Corsair Dominator RAM that is approved to go to 1800 MHz. You settings may be different but this is how you change them. Also some of the settings have to be made individually for each stick of ram while others apply to all sticks. I am not familiar with the setting for TC but assume that is the same as CAS since that's the only one missing and it's in the same order. The timings on the RAM like 8-8-8-24 are in order of CAS, tRCD, tRP, and tRAS. They are also in that same order in the BIOS.
Q: I saw where you had successfully overclocked your memory inside the BIOS. I have looked at the manual for the board but have not been able to figure out how to input the changes for the memory. Can you supply a step by step for accessing the Cell Menu and then accessing the Ram's TC, TRCD, TRP, etc. I have figured out how to change the command rate and can see the aforementioned timings but have not been able to determine where I go to change them.
A: To Overclock Memory from 1333 to 1600
Go to Cell Menu
Advanced DRAM Configuration (press enter to go into sub menu)
Change each option below by hitting enter on default setting (auto) and using up and down arrows to select new setting then hit enter to select it.
DRAM Timing Mode: Both
CAS: 8
tRCD: 8
tRP: 8
tRAS: 24 *highlight Auto and use + and – buttons to change
(must change for each stick of RAM individually)
ESC to exit sub menu
Under Advanced DRAM Configuration select FSB/DRAM Ratio
FSB/DRAM Ratio: 1/4 (for 1600 MHz RAM)
Command Rate: Auto
Scroll down further in the menu until you get to voltages
DRAM Voltage: 1.651 *highlight
Options are grayed out, you must select Auto and use + and – buttons to change value then push enter to select.
Spread Spectrum: Enable
After making these changes and it's working I recommend backing up your BIOS settins to a USB device from the M-Flash menu. I would also recommend backing up your working BIOS before making these changes in case it won’t book after you change the RAM settings. In my case I didn’t change the RAM voltage and it wouldn’t boot so I had to use the reset jumper on the Mobo to set it back to factory settings. I then had to reconfigure everything else that I had already done.
Save and Exit

890FXA-GD70 no post

Similar Messages

Maybe you are looking for