890FXA-GD70 Will Not Wake From S3 Sleep

890FXA-GD70 will not wake from S3 sleep; the power comes back on and the fans run but the video never returns and the system hard locks with a POST code of 22 or 24. Other than this issue the system is rock solid.
Windows 7 Ultimate 64
AMD Phenom II X4 955 Processor
Sapphire 5870 Graphics
Crucial M4 SSD
Corsair DDR3
No overclock
I have reproduced the issue on two 890FXA-GD70s motherboards and I am convinced that this is not a result of a failed motherboard. I also was able to move my fully installed SSD hard drive, processor, memory and graphics card to an Asus 890FX board and successfully wake from S3 sleep proving that my OS and driver installation are working correctly.
I know how to properly set the BIOS as I have installed many 890GXM-G65 motherboards for S3 sleep without issue. The problem seems unique to the 890FXA-GD70.
Is there a fix for this?

I have identified the cause. The "Extra RAID/IDE Controller" must be "Enabled" to use S3; otherwise the system will hang on the wake event. This is true even if the "Extra RAID/IDE Controller" goes unused. The "Extra RAID/IDE Controller" must be set to "Enabled" for S3 sleep to wake.
This would seem to me to be a bug since none of the other MSI boards I have used require the optional IDE controller to be enabled in order for S3 to function properly.

Similar Messages

Macbook pro will not wake from sleep without shut down?

My macbook pro 2007 will not wake from sleep without holding down start button and then restarting? Is this a serious problem?

You can Try resetting NVRAM/PRAM http://support.apple.com/kb/ht1379
You can run the Disk Utility> Repair Disk from Recovery ( command R on start)
if that does not sort it I would reinstall OS X

IPhone 1.1.4 will not wake from sleep mode

Hi all,
I have an iPhone with 1.1.4 firmware. The problem that I have is that the phone will not wake from sleep mode by pressing the "home" button. I have to press both the "home" and "sleep/power" buttons and hold them for 6 seconds for the phone to restart. I did restore the phone twice - did not solve the problem. Then, one day, I left it charging for about 3 days and when I came back it started working fine. Not for long though( After about a week of normal usage the wake up problem came back. I don't know what to do. I don't think it's the software problem, since I did complete restoration 2 times.
If the phone is connected to a charger or computer - it wakes up fine.
Thanks, Gene K
Message was edited by: rimini

rimini,
When you've restored the iPhone, have you tried setting it up as a new phone? This would truly eliminate software as a possibility.
If setting it up as a new phone doesn't correct the issue, it's probably time for service: apple.com/support/iphone/service/faq/
Hope this helps,
Raleigh

IPhone will not wake from sleep and locks up with new MMS update

Hey everyone,
Has anyone had these problems with their new update as well?
1) Sometimes my iPhone will not wake from sleep mode, I have to hold down both buttons for it to restart...I do this about 5 times a day!
2) I cannot send SMS messages and when I send more than one sometimes the iPhone locks up and will not unfreeze.
Does anyone know if this is an Apple update issue or if it is an AT&T issue? And if this is being addressed?
Apple, if you read this could there be an update to all members what is going on?

I am experiencing the same issue with iPhone 3GS. After yesterday update to 3.1.2, it is a bit better in the sense that I can restart the iPhone slightly faster but still getting frozen screen during a call. I will try to call support once more. I don't believe that the problem is solved in the new update.

HP 15t j000 will not wake from sleep/hibernate Windows 8,8.1,10

HP 15t j000 will not wake from sleep/hibernate Windows 8,8.1,10. I have to restart. I've searched high and low for answer to this. I've seen videos, played with power settings. I hoped each Windows system upgrade would fix the problem. No go. Anyone with any ideas?

Hi , Thank you for your query. I understand that after upgrading to Windows 10, it will not wake from sleep mode unless you restart. The first step I would try is to disable "Hybrid Boot' or "Hybrid Shutdown. This can be done by turning off "Fast Startup" Fast Startup - Turn On or Off in Windows 10 Next try running the "Update Troubleshooter" Windows Update troubleshooter. Once launched, it should show a screen like this. Use the second option "Background Intelligent Transfer Service", it should lead to a force update of 'Windows Updates' that may not be automatically being applied, that could fix some of these issues.
Here is a link to HP PCs - Sleep and Hibernate Issues (Windows 10, 8) that may also help. To say thanks for replying please click the thumbs up button below.If this yielded a solution please choose solution provided to help other people find this information. Best of Luck!

IMac will not wake from sleep after 10.4.8 Update

Recently after a couple of software updates my IMac goes to sleep and the Bluetooth keyboard and mouse will not wake it. The option for wake with Bluetooth is checked. I zapped the PRAM and also checked the HD, Nothing has changed. NOTE: No new software or hardware installs were done except for 10.4.8 update and the other mac software updates. This did not happen in prior versions of the OS on my iMac. Is this a new bug?
iMac G5 1.8 (pre iSight) Mac OS X (10.4.8) Bluetooth, Wake from Sleep

I've been dealing with this same issue, have tried everything, but to no avail. After MANY sessions on the phone with Apple tech support, as well as an Apple product specialist, I was advised to erase my computer and do a fresh install. I did an archive an install, which didn't help, but am not thrilled about the prospect of erasing everything and starting over. This problem started after the August 2006 round of updates. I feel it's bluetooth related, because I used a usb keyboard and mouse for a week as a test, with no problem. The funny thing is, I unchecked "allow bluetooth device to wake computer" thinking it might help, but the bluetooth devices continue to wake the computer anyway (except when it refuses to wake, of course!)
Jerry

MacBook Pro will not wake from sleep

My new 13" MacBook Pro will occasionally refuse to wake from sleep. Touching the keyboard or moving the mouse will turn on the keyboard background lights but the computer will not wake. This occurs without any peripherals attached. I have reset the PRAM and the SMC ... no help.
The only option for recovery is the hard power down with the power button and restart. Anyone else seeing this?

Yes and I hate it. I am having pretty much the same problem, and have tried the same solutions, also Iupgraded to Lion and there still has been no relief. My computer just runs slower.

MacBook pro 17" will not wake from sleep mode

Ok so my MacBook Pro 17" with osx 10.6.8 will not awaken from sleep mode. when attempting to wake it up the screen dosent come on and the mouse and keyboard do not receve any power. to get back on the computer i have to force a hard restart by holding the power button for 10 seconds then pressing it again. then it boots to where i left off when i closed the lid. i have read a few forums about this problem and i have went through all the steps of reseting various things and went as far as going into terminal using sudo to disable safe sleep and nothing helps. i noticed an unusual error in my console. here is a copy of my console log. the one in question is {7/14/13 4:52:43 AM com.apple.UserEventAgent-Aqua[118] dontAutoLoad = EMPTY!} someone please help me I am over 150 miles from the nearest apple store or authorised retailer

Active Profiles:
Battery Power                    -1*
AC Power                    -1
Currently in use:
halfdim          1
sms                    1
hibernatefile          /var/vm/sleepimage
gpuswitch          2
disksleep          10
sleep                    0 (imposed by 223)
hibernatemode          3
ttyskeepawake          1
displaysleep          5
acwake                    0
lidwake          1
Also I broke down and called support again this time a senior advisor's boss recorded the events and sent the data to their "engineering department" still waiting on the results hopefully they will get back to me sometime between today and saturday. will post the results of the tests. also this is a 2011 17in intel i5

Dual 1.25 mdd g4 will not wake from sleep

if i leave the comp on and it goes to sleep or if i force it sleep, it will not wake, the power button will not pulse its stays on solid, the display shuts down, but when i move the mouse nothing, if i click the mouse it will light up red only when i click it after that i goes back out, the display stays in sleep mode, i have to hold the power button down till it shuts off then restart it and it starts and runs fine till it goes to sleep then i have to restart
any help would be great, thanks

Well I'm having a combination of a number of these issues. Background is dual 1.25 GHz with OSX 4.11. Current situation is that the computer will not wake when put to sleep. This will happen whether I select Sleep from the Apple menu or just let the thing time out and put itself to sleep. I haven't been able to narrow it down but if I don't wait too long after sleep it seems I can log back in (even though during sleep the power light is only dim and doesn't pulse and the fans keep running so it doesn't really seem like "sleep"). Mostly the power light dims when in sleep and then is unresponsive requiring a hard reset. The most recent development is that after some time instead of going into this nebulous sleep state the computer just shuts down altogether, just like a hard crash, and I have to restart and reset the clock.
I've read many of the posts regarding problematic PCI USB cards and I did have one which I removed, but this didn't have any effect. I've reset the PMU to no effect. I should also point out that the USB ports on the back of my Apple Cinema Display don't work now either and I have to plug the keyboard directly into the Mac (though I can boot the computer from the power button on the keyboard).
Any knowledge or suggestions would be great...

PowerBook Will Not Wake from Sleep - Horizontal Lines on Display

I have a new PowerBook that I purchased last December. When my computer goes into sleep mode, it will not wake up unless I do a hard poweroff by holding in the power key for 5 seconds. When it tries to wake from sleep all I see is my mouse cursor on a black screen or the spinning beach ball. I'm also having problems with graphic applications such as Photoshop or Adobe Illustrator where I'm using lines that are only 1 pixel in length. The lines disappear when I drag them across the screen as though I'm missing a whole row of pixels or half of the line is fainter. I also notice very fine horizontal lines throughout my display. My older PowerBook does not have these lines nor this wake from sleep problem.

Contact tech support, it will need to be sent in for repair, and as long as your hardware warranty is good or you have APP the repair will cost nothing. unfortunatly this is basically your only option, unless resetting NVRAM takes care of it. to do that turn off com. hold down option, apple(2 key's left of space bar)and o, f, then turn on while holding those down. when firmware opens up type in reset-nvram, press enter then type in reset-all(include the dash in both)
this will reboot com. if this does not take care of it a repair is needed.

Will not wake from sleep mode

When I close then open the lid on my MacBook, it will not wake up from sleep mode. I have to reboot by holding down the power button for 10 sec. When it restarts, it takes a long time to get past the gray screen with the apple logo. I also have this same problem when it goes into sleep mode, when left idle. I have since changed the settings so it will not go into sleep mode when idle in system preferences. I have reset PRAM and SMC, but the problem still persists.

I have the same problem, intermittently. I think it has something to do with full-screen mode, which I use intermittently. Have you noticed this happening only when you are in a full-screen app?
I also have a MacBook Pro from 2011, and I know for sure my MagSafe power adapter is fine and not part of the problem.
I have noticed a few things that may be hints at what is happening:
one time, (all??) while my screen was basking in the glow of sunlight from the side, I saw that the screen pixels were indeed "on", that the back-light of the screen was just off.
Which led me to the conclusion that my MacBook Pro was indeed waking from sleep, the screen was just not lighting up.
But that theory was disproved this morning, when when waking from sleep, the screen was black, except for my cursor. My cursor was completely visible on a black background. Huh?? It was like some software was putting up a black modal dialog over the whole screen. Also, the Apple Logo on the back of the laptop screen was fully lit -- meaning the backlight was on. The machine was awake (curson moving on a black background), and the screen was fully back-lit.
I'm not sure yet how consistent this behavior is... I will take more careful notes each time this problem happens in the future... But, it looks like I have rogue software that is trying to make my machine look like it is sleeping.
To "capture" the culprit I think I could set up a hot-key command that takes a snapshot of all running processes in Activity Monitor. This could show what processes are running when "waking" from sleep. nabbing the culprit?
I use Snapz Pro. That is non-standard software running with control over screen functions. Maybe Snapz Pro has a problem? I doubt it, but maybe, because it has hooks into background tasks with video. Snapz Pro is my only 32-bit process. Could Snapz Pro be the cause? I use Snapz Pro all the time.
The problem seems to be related to Full-Screen mode. Could it be possible that full-screen apps sometimes have problems returning from sleep? I know there are viewControllers responsible for handling events when waking. Could the symptoms of not waking from sleep be caused by bugs in full-screen apps?

After installing mavericks, the iMac will not wake from sleep properly (at all)

I've upgraded to 10.9 (late 2012 21" iMac), and I notice in the morning when the iMac has been sleeping overnight, it will not wake up,
During the day, if it sleeps for a few hours, it seems fine, and wakes normally, prompting me to type my password,
In the morning however, I hit a key (on my wireless keyboard), and the display wakes up, I get a dark grey screen, and see the loading circle (not the beachball) in the middle, and see the cursor for a few seconds, before it then disappears, and reappears.
This cycle repeats itself,
The 'fix' is to do a forced shutdown by holding the powwer button until it shuts down, and then restart.
Anyone else find this problem/find a solution?

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, or by corruption of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal boot may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

Often will not wake after extended sleep; PowerMac G5 Quad

Why is it that My G5 Quad has repeatedly refused to wake from a sleep?
when i leave it for a night, a few days, sometimes even a few hours, the machine will not wake. keyboard, mouse, all no response. even restart key combos, nothing. I end up doing a cold restart (holding down the power button). i hate doing that.
i've run hardware tests, nothing. Perhaps its a cooling/heating issue?
once, i did the cold restart and it froze up in the moment when the red light blinks and it shuts down. but that time the red light stayed on and the fans were all blaring. I had to pull the power cord out!
it seems to occur when i leave an application running that uses the internet. folding at home, mainly.
anyone know about this? do i have to send 'er in for some fixing?

If you're in a
very dusty environment, I've seen that cause clogging
of the fans/cooling system - otherwise, suspect RAM
first as noted.
I think you may be right. i just found the processor box thingy (next to the fans?) was almost 90% caked with dust. i busted out the handy vac and carefully vac'ed it clean. i made sure not to put the vacuum nozzle right up to the box, just skirting it a half-inch above.
I called applecare just now and went through some steps to remedy the sleeping crashes;
we booted from install dvd, ran disk utility "repair disk" no errors, hardware test said no errors on a recent test. we then booted to open firmware, reset three things rebooted with some key commands, three chimes, booted, unplugged the beast, replugged, rebooted, unpluged, pushed in the little power module button. now it seems even a bit smoother than before!
only thing was that pushing the little power reset button in there is subtle. you can't really feel that you've pushed it! the guy didn't tell me to be careful not to push it more than once until after i'd tried to push it maybe ten times. apparently you just touch it and it's done, but i thought it would pop or click or slide more, but i guess not?
hopefully that will resolve the sleeping crashes, i'll have to wait and see.
if it happens again, i'll take your advice and assume it's the ram. I won't swap them, because i'm a front-end guy. i was so scared to open the box just now, and imagine my peril when i realized i had to vacuum inside there!
If it happens again, I will take it in to an applestore, that way if it breaks i am not gonna get blamed.
THANK YOU BOTH!

HP P1102w printer will not wake up after sleep (wireless setup, win8)

Bought this printer a month ago. I have no problem with both LAN +Wireless setup.
Windows8 OS
I noticed once the printer is not on (goes to sleep), it will not wake up by itself.
According to manual, if I send a print job, it should wake up by itself.
Currently, this is what I need to do.
I need to physically turn off and turn on the printer, wait for 10-15 seconds until the wifi blue light is solid (no blinking)
and then send my print job, and it will work
Just wondering whether HP has a solution to this, thanks
This question was solved.
View Solution.

Is HP ever going to fix / address this issue?
People Running the latest firmware - 20130703
And there is no option to disable Sleep mode. The max you can set it to is 1 hour.
The power physically / manually has to be powered back on, to establish IP connectivity.
This has been an issue for 2 years now!!! Come on what does it take to get an update?
Seriously?

Non retina 15" MBP will not wake up after sleep following mountain lion upgrade

I have an early 2012 15" 2.2 MBP with the 4gb video card. since upgrading to ML a lengthy sleep renders it unresponsive. it will not wake up and will have to be force shut down, then restarted to use. you can here the hard drive spin up after a long sleep (6-8 hours) but only after you hit the power button. even so it's completely unresponsive until restarted.. i noticed apple released an update for retina MBPs for the same issue. unfortunately they have not released the same update for non retina users yet.

Since you had NO problems before ML upgrade:
Not to side with the tech or you, because upgrading OS can be frustrating (it shouldn't).
It appears that you need to do a reinstall (backup first). Its pretty simple to reinstall, just go to boot drive and reinstall. You'll probably have to reinstall print drivers, other than that it's pretty straight forward.
A couple of things I'd do before and after reinstall is to repair the disk (3 times each) while in the boot drive. Then once completed choose the startup disk in system preferences or at least verify it's the startup disk, then repair permissions. If you add apps or printer drivers repair permissions again.
A major problem for lots of folks updating to a new OS is they don't think about disk health....And that's why it's important to insure everything is in mint condition before upgrading to a new OS. The same reason many choose to do a FRESH install of a new OS, by zeroing out the HDD (or SSD) and then repairing the disk and then installing the new OS (you MUST have a solid backup before doing so).
I always have at least 2 solid backups before doing so, but that's me. 100% of the time I do a fresh install of a new OS.
I have a spare computer I use as a test machine for a week or so by upgrading without fresh install. After figuring out all the possible bugs with the test machine I do a clean install of my other computers and once there stable I do a fresh install of the upgraded one.
Not a lecture on how to do things just my procedure which has served me over the years without any problems.
I have photos, videos, documents, and financial records dating back to 1991 so I must be doing something right.

890FXA-GD70 Will Not Wake From S3 Sleep

Similar Messages

Maybe you are looking for